Thermodynamic analysis of an SOFC–GT–ORC integrated power system with liquefied natural gas as heat sink

To recover the waste heat from solid oxide fuel cell (SOFC) and improve the overall electrical efficiency, a new integrated power system driven by SOFC is proposed to achieve the cascade energy utilization. This system integrates an SOFC–GT system with an organic Rankine cycle (ORC) using liquefied natural gas (LNG) as heat sink to recover the cryogenic energy of LNG. Based on the mathematical model, a parametric analysis is conducted to examine the effects of some key thermodynamic parameters on the system performance. The results indicate that the overall electrical efficiency of 67% can be easily achieved for the current system, which can be further improved with parametric optimization. An increase in fuel flow rate of SOFC can raise the net power output, but it has a negative effect on SOFC and overall electrical efficiency. The compressor pressure ratio contributes to an increase in SOFC and overall electrical efficiency, which are contrary to the effects of air flow rate and steam-to-carbon ratio. Under the given conditions, compared with the Kalina sub-system, the ORC sub-system produces 12.6% more power output by utilizing the cryogenic energy of LNG with simple configuration.     

Energetic and exergetic performance analyses of a combined heat and power plant with absorption inlet cooling and evaporative aftercooling

In this paper, exergy method is applied to analyze the gas turbine cycle cogeneration with inlet air cooling and evaporative aftercooling of the compressor discharge. The exergy destruction rate in each component of cogeneration is evaluated in detail. The effects of some main parameters on the exergy destruction and exergy efficiency of the cycle are investigated. The most significant exergy destruction rates in the cycle are in combustion chamber, heat recovery steam generator and regenerative heat exchanger. The overall pressure ratio and turbine inlet temperature have significant effect on exergy destruction in most of the components of cogeneration. The results obtained from the analysis show that inlet air cooling along with evaporative aftercooling has an obvious increase in the energy and exergy efficiency compared to the basic gas turbine cycle cogeneration. It is further shown that the first-law efficiency, power to heat ratio and exergy efficiency of the cogeneration cycle significantly vary with the change in overall pressure ratio and turbine inlet temperature but the change in process heat pressure shows small variation in these parameters.     

Thermodynamic analysis of a new combined cooling, heat and power system driven by solid oxide fuel cell based on ammonia-water mixture

Although a solid oxide fuel cell combined with a gas turbine (SOFC-GT) has good performance, the temperature of exhaust from gas turbine is still relatively high. In order to recover the waste heat of exhaust from the SOFC-GT to enhance energy conversion efficiency as well as to reduce the emissions of greenhouse gases and pollutants, in this study a new combined cooling, heat and power (CCHP) system driven by the SOFC is proposed to perform the trigeneration by using ammonia-water mixture to recover the waste heat of exhaust from the SOFC-GT. The CCHP system, whose main fuel is methane, can generate electricity, cooling effect and heat effect simultaneously. The overall system performance has been evaluated by mathematical models and thermodynamic laws. A parametric analysis is also conducted to examine the effects of some key thermodynamic parameters on the system performance. Results indicate that the overall energy conversion efficiency exceeds 80% under the given conditions, and it is also found that the increasing the fuel flow rate can improve overall energy conversion efficiency, even though both the SOFC efficiency and electricity efficiency decrease. Moreover, with an increased compressor pressure ratio, the SOFC efficiency, electricity efficiency and overall energy conversion efficiency all increase. Ammonia concentration and pressure entering ammonia-water turbine can also affect the CCHP system performance.     

Design and partial load exergy analysis of hybrid SOFC–GT power plant

This paper presents a full and partial load exergy analysis of a hybrid SOFC–GT power plant. The plant basically consists of: an air compressor, a fuel compressor, several heat exchangers, a radial gas turbine, mixers, a catalytic burner, an internal reforming tubular solid oxide fuel cell stack, bypass valves, an electrical generator and an inverter. The model is accurately described. Special attention is paid at the calculation of SOFC overpotentials. Maps are introduced, and properly scaled, in order to evaluate the partial load performance of turbomachineries. The plant is simulated at full-load and part-load operation, showing energy and exergy flows trough all its components and thermodynamic properties at each key-point. At full-load operation a maximum value of 65.4% of electrical efficiency is achieved. Three different part-load strategies are introduced. The off-design operation is achieved handling the following parameters: air mass flow rate, fuel mass flow rate, combustor bypass, gas turbine bypass, avoiding the use of a variable speed control system. Results showed that the most efficient part-load strategy corresponded to a constant value of the fuel to air ratio. On the other hand, a lower value of net electrical power (34% of nominal load) could be achieved reducing fuel flow rate, at constant air flow rate. This strategy produces an electrical efficiency drop that becomes 45%.     

Energy and exergy analyses of an integrated SOFC and coal gasification system

This paper examines an integrated gasification and solid oxide fuel cell (SOFC) system with a gas turbine and steam cycle that uses heat recovery of the gas turbine exhaust. Energy and exergy analyses are performed with two different types of coal. For the two different cases, the energy efficiency of the overall system is 38.1% and 36.7%, while the exergy efficiency is 27% and 23.2%, respectively. The effects of changing the reference temperature on the exergy destruction and exergy efficiency of different components are also reported. A parametric study on the effects of changing the pressure ratio on the component performance is presented.     

Exergy analysis of an integrated solid oxide fuel cell and organic Rankine cycle for cooling, heating and power production

The study examines a novel system that combined a solid oxide fuel cell (SOFC) and an organic Rankine cycle (ORC) for cooling, heating and power production (trigeneration) through exergy analysis. The system consists of an SOFC, an ORC, a heat exchanger and a single-effect absorption chiller. The system is modeled to produce a net electricity of around 500 kW. The study reveals that there is 3-25% gain on exergy efficiency when trigeneration is used compared with the power cycle only. Also, the study shows that as the current density of the SOFC increases, the exergy efficiencies of power cycle, cooling cogeneration, heating cogeneration and trigeneration decreases. In addition, it was shown that the effect of changing the turbine inlet pressure and ORC pump inlet temperature are insignificant on the exergy efficiencies of the power cycle, cooling cogeneration, heating cogeneration and trigeneration. Also, the study reveals that the significant sources of exergy destruction are the ORC evaporator, air heat exchanger at the SOFC inlet and heating process heat exchanger.     

Thermodynamic performance assessment of an indirect intercooled reheat regenerative gas turbine cycle with inlet air cooling and evaporative aftercooling of the compressor discharge

This study provides a computational analysis to investigate the effects of cycle pressure ratio, turbine inlet temperature (TIT), and ambient relative humidity (φ) on the thermodynamic performance of an indirect intercooled reheat regenerative gas turbine cycle with indirect evaporative cooling of the inlet air and evaporative aftercooling of the compressor discharge. Combined first and second‐law analysis indicates that the exergy destruction in various components of gas turbine cycles is significantly affected by compressor pressure ratio and turbine inlet temperature, and is not at all affected by ambient relative humidity. It also indicates that the maximum exergy is destroyed in the combustion chamber; which represents over 60% of the total exergy destruction in the overall system. The net work output, first‐law efficiency, and the second‐law efficiency of the cycle significantly varies with the change in the pressure ratio, turbine inlet temperature and ambient relative humidity. Results clearly shows that performance evaluation based on first‐law analysis alone is not adequate, and hence more meaningful evaluation must include second‐law analysis. Decision makers should find the methodology contained in this paper useful in the comparison and selection of gas turbine systems. Copyright © 2006 John Wiley & Sons, Ltd.     

High efficiency chemical energy conversion system based on a methane catalytic decomposition reaction and two fuel cells. Part II. Exergy analysis

A methane catalytic decomposition reactor-direct carbon fuel cell-internal reforming solid oxide fuel cell (MCDR-DCFC-IRSOFC) energy system is highly efficient for converting the chemical energy of methane into electrical energy. A gas turbine cycle is also used to output more power from the thermal energy generated in the IRSOFC. In part I of this work, models of the fuel cells and the system are proposed and validated. In this part, exergy conservation analysis is carried out based on the developed electrochemical and thermodynamic models. The ratio of the exergy destruction of each unit is examined. The results show that the electrical exergy efficiency of 68.24% is achieved with the system. The possibility of further recovery of the waste heat is discussed and the combined power-heat exergy efficiency is over 80%.     

A study on performance of solid oxide fuel cell‐organic Rankine cycle combined system

This study presents an energetic performance analysis for a combined power generation system consisting of a solid oxide fuel cell (SOFC) and an organic Rankine cycle (ORC). In order to simulate the SOFC–ORC combined system under steady‐state conditions, a mathematical model is developed. The developed model is used to determine the potential effects caused by the changes of the design parameters on the energetic performance of the combined system. As design parameters, turbine inlet pressure, condenser temperature, fuel utilization, current density, compressor pressure ratio, and cell operating temperature are taken into account. In this regard, the electrical power and First Law efficiency are estimated by parametrical analysis and discussed comprehensively. Results of these analyses show that the efficiency is increased about 14–25% by recovering SOFC waste heat through ORC based on investigated design parameter conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

Thermodynamic modeling of an integrated biomass gasification and solid oxide fuel cell system

An integrated process of biomass gasification and solid oxide fuel cells (SOFC) is investigated using energy and exergy analyses. The performance of the system is assessed by calculating several parameters such as electrical efficiency, combined heat and power efficiency, power to heat ratio, exergy destruction ratio, and exergy efficiency. A performance comparison of power systems for different gasification agents is given by thermodynamic analysis. Exergy analysis is applied to investigate exergy destruction in components in the power systems. When using oxygen-enriched air as gasification agent, the gasifier reactor causes the greatest exergy destruction. About 29% of the chemical energy of the biomass is converted into net electric power, while about 17% of it is used to for producing hot water for district heating purposes. The total exergy efficiency of combined heat and power is 29%. For the case in which steam as the gasification agent, the highest exergy destruction lies in the air preheater due to the great temperature difference between the hot and cold side. The net electrical efficiency is about 40%. The exergy combined heat and power efficiency is above 36%, which is higher than that when air or oxygen-enriched air as gasification agent.     

Performance comparison of three solid oxide fuel cell power systems

An energy analysis of three typical solid oxide fuel cell (SOFC) power systems fed by methane is carried out with detailed thermodynamic model. Simple SOFC system, hybrid SOFC‐gas turbine (GT) power system, and SOFC‐GT‐steam turbine (ST) power system are compared. The influences of air ratio and operative pressure on the performance of SOFC power systems are investigated. The net system electric efficiency and cogeneration efficiency of these power systems are given by the calculation model. The results show that internal reforming SOFC power system can achieve an electrical efficiency of more than 49% and a system cogeneration efficiency including waste heat recovery of 77%. For SOFC‐GT system, the electrical efficiency and cogeneration efficiency are 61% and 80%, respectively. Although SOFC‐GT‐ST system is more complicated and has high investment costs, the electrical efficiency of it is close to that of SOFC‐GT system. Copyright © 2013 John Wiley & Sons, Ltd.     

开式燃气轮机中冷回热再热循环功率和效率优化

建立了开式燃气轮机中冷回热再热（ICRR）循环有限时间热力学模型,导出了循环功率和效率解析式,优化了气流沿通流部分的压降（或低压压气机进口空气质量流率）和中间压比,得到最大功率;并在给定燃油流率的情况下,优化了气流沿通流部分的压降和中间压比,得到最大热效率,进一步在给定低压压气机进口和动力涡轮出口总面积的情况下,优化两者面积分配比,得到双重最大热效率.     

An analysis of SOFC/GT CHP system based on exergetic performance criteria

In this study, we first consider developing a thermodynamic model of solid oxide fuel cell/gas turbine combined heat and power (SOFC/GT CHP) system under steady-state operation using zero-dimensional approach. Additionally, energetic performance results of the developed model are compared with the literature concerning SOFC/GT hybrid systems for its reliability. Moreover, exergy analysis is carried out based on the developed model to obtain a more efficient system by the determination of irreversibilities. For exergetic performance evaluation, exergy efficiency, exergy output and exergy loss rate of the system are considered as classical criteria. Alternatively, exergetic performance coefficient (EPC) as a new criterion is investigated with regard to main design parameters such as fuel utilization, current density, recuperator effectiveness, compressor pressure ratio and pinch point temperature, aiming at achieving higher exergy output with lower exergy loss in the system. The simulation results of the SOFC/GT CHP system investigated, working at maximum EPC conditions, show that a design based on EPC criterion has considerable advantage in terms of entropy-generation rate.     

Effect of gasification agent on the performance of solid oxide fuel cell and biomass gasification systems

In this paper, an integrated solid oxide fuel cell (SOFC) and biomass gasification system is modeled to study the effect of gasification agent (air, enriched oxygen and steam) on its performance. In the present modeling, a heat transfer model for SOFC and thermodynamic models for the rest of the components are used. In addition, exergy balances are written for the system components. The results show that using steam as the gasification agent yields the highest electrical efficiency (41.8%), power-to-heat ratio (4.649), and exergetic efficiency (39.1%), but the lowest fuel utilization efficiency (50.8%). In addition, the exergy destruction is found to be the highest at the gasifier for the air and enriched oxygen gasification cases and the heat exchanger that supplies heat to the air entering the SOFC for the steam gasification case.     

Multiobjective optimization for exergoeconomic analysis of an integrated cogeneration system

In this paper, a novel cogeneration system integrating Kalina cycle, CO₂ chemical absorption, process, and flash‐binary cycle is proposed to remove acid gases in the exhaust gas of solid oxide fuel cell (SOFC) system, improve the waste heat utilization, and reduce the cold energy consumed during CO₂ capture. In the CO₂ chemical absorption process, the methyldiethanolamine (MDEA) aqueous solution is utilized as a solvent, and feed temperature and absorber pressure are optimized via Aspen Plus software. The single‐objective and multiobjective optimization are carried out for the flash‐binary cycle subsystem. Results show that when the multiobjective optimization is applied to identify the exergoeconomic condition, the cogeneration system can simultaneously satisfy the high thermodynamic cycle efficiency and also the low product unit cost. The optimal results of the exergy efficiency, product unit cost, and normalized CO₂ emissions obtained by Pareto chart were 75.84%, 3.248 $/GJ, and 13.14 kg/MWhr, respectively.     

Parametric optimization design for supercritical CO2 power cycle using genetic algorithm and artificial neural network

Supercritical CO₂ power cycle shows a high potential to recover low-grade waste heat due to its better temperature glide matching between heat source and working fluid in the heat recovery vapor generator (HRVG). Parametric analysis and exergy analysis are conducted to examine the effects of thermodynamic parameters on the cycle performance and exergy destruction in each component. The thermodynamic parameters of the supercritical CO₂ power cycle is optimized with exergy efficiency as an objective function by means of genetic algorithm (GA) under the given waste heat condition. An artificial neural network (ANN) with the multi-layer feed-forward network type and back-propagation training is used to achieve parametric optimization design rapidly. It is shown that the key thermodynamic parameters, such as turbine inlet pressure, turbine inlet temperature and environment temperature have significant effects on the performance of the supercritical CO₂ power cycle and exergy destruction in each component. It is also shown that the optimum thermodynamic parameters of supercritical CO₂ power cycle can be predicted with good accuracy using artificial neural network under variable waste heat conditions.     

Investigation of effect of variation of cycle parameters on thermodynamic performance of gas-steam combined cycle

The paper deals with second law thermodynamic analysis of a basic gas turbine based gas-steam combined cycle. The article investigates the effect of variation of cycle parameters on rational efficiency and component-wise non-dimensionalised exergy destruction of the plant. Component-wise inefficiencies of the combined cycle have been quantified with the objective to pin-point the major sources of exergy destruction. The parameter that affects cycle performance most is the TIT (turbine inlet temperature). TIT should be kept on the higher side, because at lower values, the exergy destruction is higher. The summation of total exergy destruction of all components in percentage terms is lower (44.88%) at TIT of 1800 K & r_p,c = 23, as compared to that at TIT = 1700 K. The sum total of rational efficiency of gas turbine and steam turbine is found to be higher (54.91%) at TIT = 1800 K & r_p,c = 23, as compared to that at TIT = 1700 K. Compressor pressure ratio also affects the exergy performance. The sum total of exergy destruction of all components of the combined cycle plant is lower (44.17%) at higher value of compressor pressure ratio (23)& TIT = 1700 K, as compared to that at compressor pressure ratio (16). Also exergy destruction is minimized with the adoption of multi-pressure-reheat steam generator configuration.     

Exergy-based performance analysis of the heavy-duty gas turbine in part-load operating conditions

The present study describes details of exergy-based performance characteristics of a heavy-duty gas turbine, 150MW-class GE 7F model. Results have shown that a chemical reaction in the combustor of which the exergy destruction ratio is 28.3% at full-load is one of the major sources of exergy destructions in the gas turbine. It was found that, in spite of its usefulness to the performance enhancement of the combined cycle plant in part-load operations, the variable inlet guide vane located in front of the multi-stage compressor caused the increase of exergy destruction in the first stage (about 10 times lager than that of other stages below 80% load) and decreased the overall compressor efficiency. Also, it was discovered that the magnitude of exergy destruction by the cooling air in turbine stages is large enough to influence the overall turbine efficiency. The exergy destruction by the cooling air is more than half of the total exergy destruction of each cooled turbine stage.     

Energy and exergy analyses of a hybrid molten carbonate fuel cell system

This study deals with the energy and exergy analysis of a molten carbonate fuel cell hybrid system to determine the efficiencies, irreversibilities and performance of the system. The analysis includes the operation of each component of the system by mass, energy and exergy balance equations. A parametric study is performed to examine the effect of varying operating pressure, temperature and current density on the performance of the system. Furthermore, thermodynamic irreversibilities in each component of the system are determined. An overall energy efficiency of 57.4%, exergy efficiency of 56.2%, bottoming cycle energy efficiency of 24.7% and stack energy efficiency of 43.4% are achieved. The results demonstrate that increasing the stack pressure decreases the overpotential losses and, therefore, increases the stack efficiency. However, this increase is limited by the remaining operating conditions and the material selection of the stack. The fuel cell and the other components in which chemical reactions occur, show the highest exergy destruction in this system. The compressor and turbine on the other hand, have the lowest entropy generation and, thus, the lowest exergy destruction.     

Energy and exergy analyses of a CFB‐based indirectly fired combined cycle power generation system

Combined cycle configuration has the ability to use the waste heat from the gas turbine exhaust gas using the heat recovery steam generator for the bottoming steam cycle. In the current study, a natural gas‐fired combined cycle with indirectly fired heating for additional work output is investigated for configurations with and without reheat combustor (RHC) in the gas turbine. The mass flow rate of coal for the indirect‐firing mode in circulating fluidized bed (CFB) combustor is estimated based on fixed natural gas input for the gas turbine combustion chamber (GTCC). The effects of pressure ratio, gas turbine inlet temperature, inlet temperatures to the air compressor and to the GTCC on the overall cycle performance of the combined cycle configuration are analysed. The combined cycle efficiency increases with pressure ratio up to the optimum value. Both efficiency and net work output for the combined cycle increase with gas turbine inlet temperature. The efficiency decreases with increase in the air compressor inlet temperature. The indirect firing of coal shows reduced use with increase in the turbine inlet temperature due to increase in the use of natural gas. There is little variation in the efficiency with increase in GTCC inlet temperature resulting in increased use of coal. The combined cycle having the two‐stage gas turbine with RHC has significantly higher efficiency and net work output compared with the cycle without RHC. The exergetic efficiency also increases with increase in the gas turbine inlet temperature. The exergy destruction is highest for the CFB combustor followed by the GTCC. The analyses show that the indirectly fired mode of the combined cycle offers better performance and opportunities for additional net work output by using solid fuels (coal in this case). Copyright © 2009 John Wiley & Sons, Ltd.