紧凑型强化传热管管束受限空间内沸腾强化换热特性

采用满液式蒸发换热器，利用强化传热管管束受限空间内早期沸腾强化机理，将中小热负荷条件下的自然对流换热转化为核沸腾换热。其换热性能大大优于降膜式蒸发换热器。对紧凑型滚压表面传热管管束在受限空间内沸腾强化换热进行实验研究，确认了满液式蒸发换热器使用紧凑型滚压强化管束具有良好的换热性能，在小管间距时有显著的沸腾换热复合强化效应。     

紧凑满液型叉排管束蒸发换热器内水的沸腾强化换热特性

采用紧凑满液型蒸发换热器,利用水平传热管叉排管束狭窄空间内早期沸腾强化换热机理将中小热负 荷条件下的自然对流换热转化为旺盛核沸腾换热,换热性能大大优于传统的降膜式蒸发换热器。对水平传热管 管束在受限空间内沸腾强化换热进行实验研究,确认了紧凑满液式水平管蒸发换热器具有良好的换热性能,传 热管在管束中的位置对换热特性已经没有明显影响,随着压力增加,受限空间内沸腾强化换热强化效果显著增 加。     

紧凑高效型水平管束降膜蒸发换热器的实验研究

在大气压条件下使用单列和3列叉排光滑管和滚压强化换热管紧凑管束进行了水降膜蒸发换热实验,确认了滚压管在中,低热负荷范围内能够增强换热系数3～4倍,有很好的沸腾强化换热性能。管间距及液膜溅射损失对蒸发换热特性影响很小。同时也考察了单列和3列管束换热特性闯的差异。实验发现这种差异在低雷诺数区域时更加明显。     

满液型海水淡化蒸发器的换热特性研究

海水淡化装置，太阳能或余热吸收式制冷机中的蒸发换热器目前使用管排外降膜式蒸发方式。如将传热管束紧凑排列置于饱和状态液体中则变为满液式蒸发换热器，利用传热管束间受限空间内早期沸腾强化换热机理，将中小热负荷条件下的自然对流换热转化为核沸腾换热，在间隙尺寸适宜时，其换热性能可能优于降膜式蒸发换热器。该研究以盐水为实验工质，对紧凑传热管束受限空间的沸腾换热进行了实验研究，确认了满液式蒸发换热器也具有很好的换热性能，在中小热负荷条件下甚至超过降膜式蒸发换热器。     

低压条件下紧凑式顺排管束满液型蒸发换热器的强化换热特性研究

提出了一种新型紧凑式顺排光滑管束组成的满液式蒸发换热器。在低压条件下对水平光滑顺排管束的小空间内沸腾强化换热特性进行了实验研究,确认了管距、管位置和运行压力对强化换热性能的影响。实验表明存在一个能得到最大强化换热效果的最佳管距,这一最佳管距接近沸腾气泡的脱离直径。压力对强化换热效果也有重要影响:随着压力降低,强化换热效果也逐步减弱。实验结果对高效节能型蒸发换热器设计提供了设计基础。     

紧凑传热管束受限空间内沸腾强化换热特性

海水淡化装置以及太阳能或余热吸收式制冷机中的蒸发换热器,采用管排外降膜式蒸发方式,它具有很多优点,但管间距离较大,以致尺寸较大,供液方式较复杂。将传热管束紧凑排列置于饱和状态液体中,将其变为满液式蒸发换热器,利用传热管束间受限空间内早期沸腾强化机理,将中小热负荷条件下的自然对流换热转化为核沸腾换热,在间隙尺寸适宜时,其换热性能可能优于降膜式蒸发换热器。对紧凑传热管束在受限空间内沸腾强化换热进行实验研究,确认了满液式蒸发换热器具有良好的换热性能,在中小热负荷条件下甚至超过降膜式蒸发换热器。     

紧凑式两相换热器中管式换热元件沸腾传热实验研究

以烃类物质（丙烷和正戊烷）作为工质,进行了紧凑式换热器中带有加工配置表面的管式换热元件池沸腾实验研究。其中,单管实验温度工况为２５３Ｋ￣２９３Ｋ（饱和工质）。实验中所采用的换热元件为重入式结构加工配置表面的强化传热管和光管以及低助管。针对由４５根光管或带有加工配置表面的管子所构成的叉排管束进行了实验研究,实验工质为丙烷和正戊烷,实验温度分别为两种工质在２６３Ｋ和３０８Ｋ之间的饱和和温度。并将所得实     

紧凑传热管束爱限空间内沸腾强化换热特性

海水淡化装置以及太阳能或余热吸收式制冷机中的蒸发换热器,采用管排我降膜式蒸发方式,它具有很多优点,但管间距离较大,以致尺寸较大,供液方式较复杂。将传热管束紧凑排列置于饱和状态液体中,将其变为满液式蒸发换热器,利用传热管束间受限空间内早期沸腾强化机理,将中小热负荷条件下的自然对流换热转化为核沸腾换热,在间隙尺寸适宜时,其换热性能可能优于降膜式蒸发换热器。     

外加电场强化苯自然对流和沸腾换热的试验研究

对沉浸在非极性有机液体工质苯中的平板表面自然对流和沸腾换热的外加电场强化进行了试验，得出了自然对流和沸腾换热的换热系数、强化效果与电场电压、热流密度的关系。试验数据表明外加电场对平板表面苯的自然对流换热和沸腾换热都有一定的强化效果，但外加电场对平板表面苯自然对流换热的强化效果明显好于对沸腾换热的强化效果；且平板表面苯的自然对流换热的强化效果与试验所给定的热流密度无关，而外加电场对平板表面苯的沸腾换热的强化效果随热流密度的增大而减弱。     

内燃机冷却水腔表面形貌对沸腾换热影响的研究

愈发严重的能源和环境问题要求内燃机的结构更加紧凑和复杂,导致缸盖等零部件所受的热负荷急剧增加,这对其内部冷却水腔提出了更高的换热要求。对流换热已不能满足苛刻的冷却要求,沸腾换热应运而生。据气泡动力学可知,汽化核心更倾向于分布在狭窄的凹坑处,因此在加热面上布置一定的表面形貌能够有效提高沸腾换热效果。文中设计4种形貌,并比较分析不同形貌的强化换热能力。结果表明:圆柱形凸起形貌强化沸腾换热和对流换热的效果最好,其次是圆柱形凹坑形貌,圆台形凹坑强化沸腾换热的效果好于半球形凹坑形貌,但强化对流换热的效果比半球形凹坑形貌差。不同凹坑形貌,汽化核心更倾向于分布在凹坑底部的狭窄区域,圆柱形凹坑底部狭窄区域的范围最广,有利于汽泡成核,圆台形凹坑次之,而半球形凹坑内部较为平整,不利于成核。     

碳钢_水热虹隙管内部强化传热机理研究

在微层蒸发模型的理论基础上,对热虹吸管内部设置分流管结构强化沸腾传热者机理分析。建立分流管强化热哐吸管内部沸腾传热模型,同时选择七种不同的分流管开孔结构,与光滑管进行了对比实验研究,寻得最佳分流管结构,并综合大量实验数据建立强化沸腾传热准数方程式。     

Enhancement of boiling heat transfer in restricted spaces in compact horizontal tube bundles

ln desalinization devices and some heat exchangers making use of low‐quality heat energy, both wall temperatures and heat fluxes of heated tubes are quite low and generally cannot cause boiling in flooded‐type tube bundle evaporators with a large tube spacing. But when the tube spacing is very small, boiling in restricted spaces can occur and induce a higher heat transfer than that of a falling film or pool boiling at the same heat flux. This study investigated experimentally the effects of tube spacing, positions of tubes, and heating status of tubes as well as surface status (smooth and roll‐worked) on boiling in restricted spaces in compact horizontal tube bundle evaporators under atmospheric pressure. The experimental results provide a restricted space boiling database for water in smooth and enhanced surface tube bundles. Of particular importance is information concerning the influence of tube spacing of flooded‐type tube bundle evaporators, especially for the case of zero pitch, when the neighboring tubes are contacting each other. © 2001 Scripta Technica, Heat Trans Asian Res, 30(5): 394–401, 2001     

表面强化管外池沸腾传热特性研究

为实现节能降耗,开发了多种强化沸腾传热的高效换热管。以水为工质,在0.1MPa下对垂直光管、烧结多孔管和T槽管进行了池沸腾传热实验研究,并分析了沿管子轴向的温度分布。实验结果表明,烧结多孔管与T槽管能显著降低起始沸腾过热度、强化沸腾传热:烧结多孔管和T槽管的起始沸腾过热度比光管的低1.5K左右;烧结多孔管和T槽管的核态沸腾传热系数分别为光管的2.4～3.2倍和1.6～2.0倍。此外,烧结多孔管和T槽管能降低相同热流密度下的壁面温度,且有利于降低管子轴向的温差。     

水平窄空间沸腾传热的实验研究

通过对五种尺寸的窄空间试验元件分别以水和乙醇做工质进行实验。研究了窄空间间距、窄空间尺寸、不同工质及不同热流密度对窄空间沸腾性能的影响。结果表明：当窄空间尺寸与热流通等因素组合恰当时。其换热系数可比大空间池沸腾提高3～6倍；临界热流密度有所降低。     

Experimental research of pool boiling heat transfer in horizontal narrow spaces

Much progress has been made in high‐performance electronic chips, the miniaturization of electronic circuits and other compact systems recently, which brings about a great demand for developing efficient heat removal techniques to accommodate these high heat fluxes. With this objective in mind, experiments were carried out on five kinds of test elements with distilled water and ethanol as working liquids. The test elements used in these experiments consisted of five parallel discs with diameters varying from 5 mm to 40 mm. The experiments were performed with the discs oriented horizontally and uniform heat fluxes applied at the bottom surfaces. The influence of narrow spacing, space size, working liquid property, and heat flux on boiling heat transfer performance in narrow spaces has been investigated. Experimental results showed that the boiling heat transfer coefficient of a narrow space was 3 to 6 times higher than that of pool boiling when the narrow space size and heat flux combine adequately, but the critical heat flux was lower than that of pool boiling. © 2004 Wiley Periodicals, Inc. Heat Trans Asian Res, 33(5): 307–315, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20017     

Enhanced Boiling Heat Transfer of the Compact Staggered Tube Bundles under Sub-Atmospheric Pressures

An experimental investigation was carried out on the boiling heat transfer enhancement of water on plain tubes in compact staggered tube-bundle evaporators under atmospheric and sub-atmospheric pressures. The experiment investigated the effects of the tube spacing and positioning and the test pressure on the boiling heat transfer characteristics in restricted spaces of compact tube bundles. The experimental results indicated that for compact tube bundles, the effect of the tube spacing is very significant on the boiling heat transfer. The boiling heat transfer has a maximum enhancement when the tube spacing is so selected as to take an optimum value. The enhanced heat transfer efficiency for the compact bundles would gradually decrease as the test pressure was reduced.     

Enhancement of boiling heat transfer in a 5 × 3 tube bundle

The results of an experimental investigation on nucleate boiling heat transfer in an electrically heated 5 × 3 in-line horizontal tube bundle under pool and low cross-flow conditions of saturated water near atmospheric pressure are presented here. It is observed that the heat transfer coefficient is minimum on bottom row tubes and increases in the upward direction with maximum values on top row tubes. Also, heat transfer coefficient on central column tubes was found to be slightly higher than those on the corresponding side tubes. Further, a Chen-type relation has been used to determine the local boiling heat transfer coefficient on a tube in a heated tube bundle.     

自转清洗扭带管对流传热强化机理的实验研究

具有传热强化功能的自转螺旋扭带清洗防垢技术发展较快。应用激光测速仪LDV(Laser Doppler Velocimeter)实验研究自转清洗扭带管内流体的湍流特性。结果表明：在自转扭带竹带动下,管内流体的流动结构发生了反常态的变化。在近管壁环形区域内流体的轴向分速度明显比管中心区域的高,轴向湍流度比无白转扭带时大;切向分速度随半径的增大而增大,并且存在很大的径向湍流度。这些结果初步说明了自转螺旋扭带管对流传热强化的机理是：管内由扭带带动形成的强制旋流和轴向平行流叠加而形成的螺旋流动,以及近管壁环形区域内流速的增大,不仅加强了边界层流体的扰动以及边界层流体与主流流体的混合,并且使边界层厚度减簿,从而才使管内的对流传热得以强化。本文试验研究的结果为自转螺旋扭带管内对流传热强化机理的深入理论研究提供实验基础。