The effect of nanoscale vanadium pentoxide on the electrical and mechanical properties of poly(vinyl alcohol)

Poly(vinyl alcohol) (PVA) loaded with vanadium pentoxide (V₂O₅) nanoparticles was successfully prepared at room temperature and ambient pressure. Transmission electron microscopy was used to characterize the final product. It was found that V₂O₅ nanoparticles were well dispersed and uniform in shape and that the diameter of the particles was confined to within 8 nm. Addition of small amounts (0.2–1 wt%) of nanoparticulate V₂O₅ to PVA increased the electrical conductivity as well as the modulus of elasticity. The deformation behaviour after preparing the nanocomposites, irrespective of V₂O₅ concentration, is similar to that of the unfilled elastomer, implying that the mechanism of large deformation is mainly governed by the matrix. Copyright © 2007 Society of Chemical Industry     

Morphology and mechanical and electrical properties of oriented PVA-VGCF and PVA-MWNT composites

The composites poly(vinyl alcohol) (PVA) and vapor growth carbon fiber (VGCFs) and multi wall carbon nanotubes (MWNTs) were prepared by gelation/crystallization from the mixture of dimethyl sulfoxide (DMSO) and water (H₂O). The composite films were elongated to 5-10-fold uniaxially. The mechanical properties of PVA composites were improved significantly by introduction of VGCFs and MWNTs and also by the orientation of fillers. Compared to VGCFs, MWNTs was more effective to improve the electric conductivity of the composites because of its network structure. The change in the electrical conductivity for the PVA/MWNT composites containing 5 wt% MWNT was independent of the draw ratio up to eight-fold indicating no disruption of the network formation. A certain high level of filler content was proved to be necessary for the promotion of both mechanical and electrical properties in oriented composite.     

Effect of vanadium pentoxide on the mechanical,thermal, and electrical properties of poly(vinyl alcohol)/vanadium pentoxide nanocomposites

In this study, we examined the effect of vanadium pentoxide (V₂O₅) on the mechanical, thermal, and morphological properties of poly(vinyl alcohol) (PVA)/V₂O₅ nanocomposites. The PVA/V₂O₅ nanocomposites were prepared by solution mixing, followed by film casting. The results show that the Young's moduli of the resulting nanocomposites films were higher than the pure PVA modulus with increasing V₂O₅ content, and it reached a maximum point at about 0.4 wt % V₂O₅ content at 8.55 GPa. The tensile strength and stress at break increased with increasing V₂O₅ content. The addition of V₂O₅ did not affect the melting temperature. The crystallization temperatures of PVA were significantly changed with increasing V₂O₅ content. The 5% weight loss degradation temperature of the nanocomposites was measured by thermogravimetric analysis. The degradation temperatures of the V₂O₅ nanocomposites increased with increasing filler content and were higher than the degradation temperature of pure PVA; this showed a lower thermal stability compared to those of the nanocomposites. The results show that the thermal stability increased with the incorporation of V₂O₅ nanoparticles. The dielectric constant of PVA had a tendency to improve when the dispersion of particles was effective. The morphology of the surfaces the nanocomposites was examined by scanning electron microscopy. We observed that the dispersion of the V₂O₅ nanoparticles was relatively good; only few aggregations existed after the addition of the V₂O₅ nanoparticles at greater than 0.4 wt %. In perspective, the addition of 0.4 wt % V₂O₅ nanoparticles into PVA maximized the mechanical, thermal, and electrical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Eco-friendly poly(vinyl alcohol)/delaminated V2C MXene high-k nanocomposites with low dielectric loss enabled by moderate polarization and charge density at the interface

High-dielectric-constant (high-k) polymer/conductor composites with low dielectric loss are desirable for energy storage. However, high leakage currents from interfacial regions with high charge density are difficult to handle. In this work, high permittivity and low dielectric loss were achieved in poly(vinyl alcohol) (PVA)/V₂C MXene nanocomposite films fabricated by solution casting by taking advantage of the interfacial compatibility and moderate interfacial charge density of the nanocomposites. Water-soluble PVA was utilized as the polymer matrix. Delaminated V₂C MXene nanosheets with appropriate conductivity were prepared and used as the filler. The mild interface polarization of the nanocomposites was responsible for achieving favourable permittivity values. The small gap between the work functions of PVA and V₂C contributed to moderate interfacial charge density values and thus low dielectric loss values. A proportional correlation between the interfacial charge density and the conductivity of composites was also verified. The depth of charge injection from the MXene to PVA was found to be half of the interlamellar spacing of the delaminated MXene. The dependence of the electrical properties of the nanocomposites on the frequency and MXene content was also studied. The composite with 4 wt% MXene exhibited a permittivity of ~24 (16 times that of PVA) and a dielectric loss of ~0.14 (1.5 times that of PVA) at 1 kHz, as well as breakdown strength of ~31 MV m⁻¹ (63% of PVA). This work might enable environmentally friendly fabrication of promising composite dielectrics.     

Tailored thermal expansion and electrical properties of α-Cu2V2O7/Al

α-Cu₂V₂O₇/Al composites (with 5–80 wt% of Al) were prepared by a solid state method. Their structural stability, thermal expansion, hardness and electrical properties were studied in detail. The coefficient of thermal expansion (CTE) and hardness of α-Cu₂V₂O₇/Al composites sample can be tailored with the content of Al. The CTE is only 0.49×10⁻⁶ K⁻¹ (RT–780 K) when the Al content is 10 wt%, which is near-zero thermal expansion. The electrical conductivity of α-Cu₂V₂O₇/Al composites increases with increasing the content of Al. When the content of Al is larger than 40 wt%, the α-Cu₂V₂O₇/Al composites exhibit excellent electrical conductivity, which can be mainly attributed to the conductive percolation phenomena of Al in the α-Cu₂V₂O₇/Al composites.     

Effect of the filler morphology on the crystallization behavior and dielectric properties of the polyvinylidene fluoride-based composite

Ceramic/polymer composites can be chemically stable, mechanically strong, and flexible, which make them candidates for electric devices, such as pressure or temperature sensors, energy storage or harvesting devices, actuators, and so forth. Depending on the application, various electrical properties are of importance. Polymers usually have low dielectric permittivity, but increased dielectric permittivity can be achieved by the addition of the ceramic fillers with high dielectric constant. With the aim to enhance dielectric properties of the composite without loss of flexibility, 5 wt% of BaTiO₃-Fe₂O₃ powder was added into a polyvinylidene fluoride matrix. The powder was prepared by different synthesis conditions to produce core/shell structures. The effect of the phase composition and morphology of the BaTiO₃-Fe₂O₃ core/shell filler on the structure and lattice dynamics of the polymer composites was investigated. Based on the results of the thermal analysis, various parameters of ceramic/polymer composites were determined. Differences in the phase composition and morphology of the filler have an influence on the formation of various polyvinylidene fluoride allomorphs and the degree of crystallinity. Furthermore, the dielectric performances of pure polyvinylidene fluoride and the polymer/ceramic composites were measured.     

Intercalation of conducting poly(N‐propane sulfonic acid aniline) in V2O5 xerogel

Poly(N‐propane sulfonic acid aniline) (PSPAN) can be formed between the lamellas of V₂O₅ xerogel by in situ oxidative polymerization/intercalation of N‐propane sulfonic acid aniline in the presence of air (V₂O₅ being the oxidation agent). The PSPAN/V₂O₅ nanocomposites were characterized by XRD, TEM, TGA, FTIR, UV–vis‐NIR, and conductivity measurement. The results show that the V₂O₅ maintains lamellar structure, but its interlayer spacing has increased from 1.18 to 1.31 nm. The FTIR spectra indicate that there is interaction between negatively charged oxygen of the sulfonic group of PASPN and the vanadium ion in V₂O₅ matrix. The electrical conductivity of PSPAN/V₂O₅ nanocomposite reached the value of 1.2 × 10^?2 S/cm, which is 10⁴ times higher than that of the V₂O₅ xerogel, and is 10² times more than that of the PSPAN. It was found that the aging in air facilitated the chain growth of PSPAN between the V₂O₅ lamellas, resulting in the increase of the electrical conductivity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2569–2574, 2007     

Structural,Dielectric Permittivity and Optical Characteristics of Casting Poly Vinyl Alcohol/Calcium Nickel Aluminate Nanocomposite Films

Triplex hybrid nanofiller (CaNiAl₂O₅) have been synthesized by sol-gel method and its nanocomposite (NC) films were incorporated with poly vinyl alcohol (PVA). The scanning electron microscopy (SEM) was used to probe morphological behaviors and dispersion of CaNiAl₂O₅ in PVA matrix. In order to probe the microstructure X-ray diffraction (XRD) and FTIR were performed on PVA/CaNiAl₂O₅ NCs. Based on the results of both XRD and transmission electron microscopy (TEM), the average particle size of the CaNiAl₂O₅ lies in the range 7–15 nm. The current (I) – voltage (V) behaviors were studied using LCR-meter at room temperature. The dc-conductivity increases with increasing in both CaNiAl₂O₅ at different voltages. The dielectric constant exhibits higher values at lower frequency and increases with nanoparticle (NP) loading due to increase in polarization particles in polymer matrix. The ac conductivity tends to increase with increase frequency and NPs content. The cyclic voltammetric data indicate the NC with 8wt% NPs exhibit higher specific capacitance as compared with PVA. The optical constants of the NCs were evaluated from UV-Visible spectra. The band gap energies has a blue shift from 4.4 eV (PVA) to 2.8 eV (PVA/8wt% CaNiAl₂O₅), whereas refractive index (RI) and the optical conductivity of NCs increased with an increasing in NPs content.     

Infrared and raman characterization of V<Subscript>2</Subscript>O<Subscript>5</Subscript> on zirconia modified with WO<Subscript>3</Subscript> and activity for acid catalysis

Vanadium oxide supported on zirconia modified with WO₃ was prepared by adding Zr(OH)₄ powder into a mixed aqueous solution of ammonium metavanadate and ammonium metatungstate followed by drying and calcining at high temperatures. The characterization of prepared catalysts was performed by using FTIR, Raman, and XRD. In the case of calcination temperature at 773 K, for samples containing low loading V₂O₅ below 18 wt%, vanadium oxide was in a highly dispersed state, while for samples containing high loading V₂O₅ equal to or above 18 wt%, vanadium oxide was well crystallized due to the high V₂O₅ loading on the surface of ZrO₂. The ZrV₂O₇ compound was formed through the reaction of V₂O₅ and ZrO₂ at 873 K, and the compound decomposed into V₂O₅ and ZrO₂ at 1,073 K, these results were confirmed by FTIR and XRD. Catalytic tests for 2-propanol dehydration and cumene dealkylation have shown that the addition of WO₃ to V₂O₅/ZrO₂ enhanced both catalytic activity and acidity of V₂O₅-WO₃/ZrO₂ catalysts. The variations in catalytic activities for both reactions are roughly correlated with the changes of acidity.     

Suppressing fire hazard of poly(vinyl alcohol) based on (NH4)2[VO(HPO4)]2(C2O4)·5H2O with layered structure

Two-dimensional layered ammonium vanadium oxalate-phosphates (AVOPh) with the structural formula of (NH₄)₂[VO(HPO₄)]₂(C₂O₄)·5H₂O are synthesized though a hydro-thermal method, which is dispersed into poly(vinyl alcohol) (PVA) matrix to prepare PVA/AVOPh composites. The results of thermal analysis indicate that AVOPh and PVA have similar decomposition temperature from 280 to 500°C, which is critical for choosing flame retardant. The incorporation of AVOPh significantly improves the thermal stability and flame retardancy of PVA/AVOPh composites that the T_5% value of PVA/2 wt% AVOPh composites is up to 215°C, and the residue of PVA/8 wt% AVOPh composites is enhanced to 16.9%, while those of pure PVA are only 178°C and 2.4%. PVA/4 wt% AVOPh composites can pass V-0 level, and its limiting oxygen index value is up to 32.0%. Furthermore, the peak heat release rate (PHRR) and total heat release (THR) of PVA/AVOPh composites are obviously decreased, which reduced by 43.4% and 43.8% with the addition of 4 wt% AVOPh, compared with those of pure PVA. The excellent thermal stability and flame retardancy are mainly attributed to the uniform dispersion and barrier effect of 2D layered AVOPh, the release of crystal water, ammonia and phosphorus free radicals and the two-phase flame retardant catalytic mechanism of vanadium and phosphorus.     

Synthesis and characterization of poly(o‐anisidine)/V2O5 and poly(o‐anthranilic acid)/V2O5 nanocomposites

Poly(o‐anisidine)/V₂O₅ and poly(o‐anthranilic acid)/V₂O₅ nanocomposites were prepared by in situ intercalative polymerization, and the structure and electrical properties of these nanocomposites were investigated using GPC, TGA, XRD, TEM, FTIR, UV‐vis as well as conductivity measurement. The results show that the steric effect and nature of the substituting groups in the aromatic ring has an influence on the structure and electrical properties of the nanocomposites. Poly(o‐anisidine) or poly(o‐anthranilic acid) exists as a monolayer of outstretched chains in the gallery of the V₂O₅ xerogel owing to the confined environment in the nanometer‐size gallery. And intercalation of poly(o‐anisidine) or poly(o‐anthranilic acid) can improve the conductivity of V₂O₅ xerogel. Copyright © 2005 Society of Chemical Industry     

Structural Characteristics and Electrical Conductivity of Vanadium-doped lithium Ultraphosphate Glasses

Glasses of the 33.5Li₂O-66.5P₂O₅-xV₂O₅ (mol. %) system with (0 ≤ x ≤ 5) were prepared by the normal melting and annealing technique. Their physical and spectroscopic properties such as X-ray powder diffraction (XRD), density, infrared spectroscopy and electrical conductivity were investigated. The composition dependent density shows an initial decrease at 0.1 mol.% of V₂O₅ followed by an increase in density with further addition of the V₂O₅ content. The structure of these glasses has been studied by recording the Fourier-transform infrared spectroscopy (FTIR) over the range 400–1800 cm^?1. Vibrational modes are assigned to different types of phosphate groups in the glass network. The temperature (333–452 K) and composition dependence of direct current (DC) electrical conductivity were measured. The electric conductivity is observed to increase with the first addition of vanadium oxide reflecting the presence of V⁴⁺ions that take part within modifying positions in the glass network .Then, the electric conductivity is found to decrease with the further increase in the content of V₂O₅ up to 5 mol.% reflecting the formation of V⁵⁺ions that take part as network forming positions in the glass network. The variations in density and electrical conductivity with V₂O₅ content are discussed in terms of changes in the glass structure.     

A study on polymer blend electrolyte based on PVA/PVP with proton salt

Proton-conducting polymer blend electrolytes based on PVA–PVP–NH₄NO₃ were prepared for different compositions by solution cast technique. The prepared films are investigated by different techniques. The XRD study reveals the amorphous nature of the polymer electrolyte. The FTIR and laser Raman studies confirm the complex formation between the polymer and salt. DSC measurements show decrease in T _g with increasing salt concentration. The ionic conductivity of the prepared polymer electrolyte was found by ac impedance spectroscopy analysis. The maximum ionic conductivity was found to be 1.41 × 10^?3 S cm^?1 at ambient temperature for the composition of 50PVA:50PVP:30 wt% NH₄NO₃ with low-activation energy 0.29 eV. The conductivity temperature plots are found to follow an Arrhenius nature. The dielectric behavior was analyzed using dielectric permittivity (ε*) and the relaxation frequency (τ) was calculated from the loss tangent spectra (tan δ). Using this maximum ionic conducting polymer blend electrolyte, the primary proton battery with configuration Zn + ZnSO₄·7H₂O/50PVA:50PVP:30 wt% NH₄NO₃/PbO₂ + V₂O₅ was fabricated and their discharge characteristics studied.     

Improved dielectric and mechanical properties of Ti3C2Tx MXene/silicone rubber composites achieved by adding a few boron nitride nanoplates

MXenes have attracted great attentions in the fabrication of dielectric polymer composites because of their excellent electrical conductivity. However, the high dielectric loss tangent would suppress the application of such polymer-based composites. Incorporating insulating fillers might be a solution. Herein, Ti₃C₂T_x MXene/silicone rubber (SR) composites incorporated with boron nitride (BN) nanoplates were prepared. The homogeneous distribution of fillers was obtained in the composites, which was also thermally stable up to 400 °C. Dielectric constant of 7.06 (2.54 times of pure SR) and dielectric loss tangent of 0.00131 were achieved when the filling contents of MXene and BN in SR composite were 1.2 wt% and 5 wt%, respectively. The improved dielectric constant can be ascribed to the enhanced interfacial polarization and the formation of conductive network, while the low dielectric loss tangent can be due to the insulating interlayers of BN which could inhibit the transfer of free electrons from conductive fillers to the insulating polymer matrices. BN/MXene/SR composites displayed improved mechanical properties (tensile stress of 671 kPa and elongation at break of 353%) and good flexibility (elastic modulus of 540 kPa) due to the low filling content of fillers. This work is promising for preparing dielectric polymer composites in applications of electronic devices.     

Preparation,characterization, electrical and antibacterial properties of sericin/poly(vinyl alcohol)/poly(vinyl pyrrolidone) composites

In this study, we focused on the fabrication of poly(vinyl alcohol) (PVA)/poly(vinyl pyrrolidone) (PVP)/sericin composites via a simple solution‐blending method. The composites were characterized by Fourier transform infrared (FTIR) spectroscopy, UV spectroscopy, X‐ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry, thermogravimetric analysis (TGA), and measurements of the conductivity, tensile strength, and antibacterial activity against Staphylococcus aureus. The results of FTIR and UV spectroscopy implied the occurrence of hydrogen bonding between sericin and the PVA/PVP blend. The structure and morphology, studied by XRD and SEM, revealed that the sericin particles were well dispersed and arranged in an orderly fashion in the blend. The glass‐transition temperature (T_g) of the composite was higher than that of the pure blend, and the T_g value shifted toward higher temperatures when the volume fraction of sericin increased. TGA indicated that sericin retarded the thermal degradation; this depended on the filler concentration. The mechanical and electrical properties, such as the tensile strength, alternating‐current electrical conductivity, dielectric constant, and dielectric loss of the composites, were higher than those of the pure blend, and these properties were enhanced when the concentration of sericin was increased up to 10 wt % filler content, whereas the elongation at break of the composite decreased with the addition of sericin particles. The antibacterial properties of the composite showed that sericin had a significant inhibitory effect against S. aureus. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43535.     

A Concurrent Enhancement of Both In-Plane and Through-Plane Thermal Conductivity of Injection Molded Polycarbonate/Boron Nitride/Alumina Composites by Constructing a Dense Filler Packing Structure

In this work, a facile strategy is proposed to concurrently enhance both in-plane and through-plane thermal conductivity of injection molded polycarbonate (PC)-based composites by constructing a dense filler packing structure with planar boron nitride (BN) and spherical alumina (Al₂O₃) particles. The state of orientation of BN platelets is altered with the presence of Al₂O₃, which is favorable for improving both in-plane and through-plane thermal conductivity of subsequent moldings. Rheological analysis showed that the formation of intact thermal conductive pathways is crucial to the overall enhancement of thermal conductivity. Both in-plane and through-plane thermal conductivity of PC/BN(20 wt%)/Al₂O₃(40 wt%) composites reached as high as 1.52 and 1.09 W mK⁻¹, which are 485% and 474% higher than that of pure PC counterparts, respectively. Furthermore, the prepared samples demonstrated excellent electrical insulation and dielectric properties which show potential application in electronic and automotive industries.     

Thermal,electrical, and mechanical properties of addition-type liquid silicone rubber co-filled with Al2O3 particles and BN sheets

The addition-type liquid silicone rubber (ALSR) co-filled with spheroidal Al₂O₃ and flaky BN was prepared by the mechanical blending and hot press methods to enhance the thermal, electrical, and mechanical properties for industrial applications. Morphologies of ALSR composites were observed by scanning electron microscopy (SEM). It was found that the interaction and dispersion state of fillers in the ALSR matrix were improved by the introduction of BN sheets. Thermal, electrical, and mechanical performances of the ALSR composites were also investigated in this work. The result indicated that the thermal conductivity of ALSR can reach 0.64 W m⁻¹ K⁻¹ at the loading of 20 wt% Al₂O₃/20 wt% BN, which is 3.76 times higher than that of pure ALSR. The addition of Al₂O₃ particles and BN sheets also improve the thermal stability of ALSR composites. Moreover, pure ALSR and ALSR composites showed relatively lower dielectric permittivity (1.9–3.1) and dielectric loss factor (<0.001) at the frequency of 10³ Hz. The insulation properties including volume resistivity and breakdown strength were improved by the introduction of flaky BN in the ALSR matrix. The volume resistivity and characteristic breakdown strength E₀ are 6.68 × 10¹⁵ Ω m and 93 kV/mm, respectively, at the loading of 20 wt% Al₂O₃/20 wt% BN. In addition, the mechanical characteristics including elongation at break and tensile strength of ALSR composites were also enhanced by co-filled fillers. The combination of these improved performances makes the co-filled ALSR composites attractive in the field of electrical and electronic applications.     

Synthesis,characterization and electrical properties of polypyrrole/V<Subscript>2</Subscript>O<Subscript>5</Subscript> composites

Polypyrrole (PPy) and its composites with vanadium pentoxide (V₂O₅) were synthesized in aqueous medium by chemical oxidation polymerization using FeCl₃·6H₂O as an oxidant. The materials were characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffractometry (XRD), thermogravimetry analyzer (TGA), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), UV/visible spectroscopic techniques and LCR-meter. The FT-IR results confirmed the successful synthesis of PPy and PPy/V₂O₅ composites. The XRD study showed the amorphous and crystalline nature of PPy and PPy/V₂O₅ composites, respectively. The TGA analysis showed slight increase in the thermal stability of the composites. The SEM data verified the porous nature of PPy and the composites. The UV/visible spectrometry confirmed the doping of PPy in composites. The electrical properties of the materials displayed their semiconducting nature. The resistance of the samples was found to be dependent on temperature and the contents of V₂O₅ in the composites.     

Effect of V2O5 Loading on Propane Combustion over Pt/V2O5–Al2O3 Catalysts

Propane combustion was studied on Pt(0.4%)/V₂O₅–Al₂O₃ catalysts containing up to 20% V₂O₅. The density, strength and nature of surface acid sites were determined by TPD of NH₃ and FTIR spectra of adsorbed pyridine. The sample acidity increased with the vanadium content, essentially because the addition of vanadium oxide generated Brønsted acid sites. The Pt dispersion as determined by H₂ chemisorption increased with increasing V₂O₅ loading. The sample activity for propane combustion was evaluated through both conversion versus temperature (light-off curves) and kinetically-controlled conversion versus time catalytic tests. The propane combustion turnover rate on Pt/V₂O₅–Al₂O₃ increased with the amount of vanadium, probably because the intrinsic Pt oxidation activity increases with the sample acidity.     

In-situ formation of Al2O3/Al core-shell from waste material: Production of porous composite improved by graphene

Aluminum dross produced from aluminum industry was used to fabricate Al₂O₃/Al porous composites. The dross was milled for 20?h to obtain nano powder. The milled material was examined by TEM and XRD. Graphene (up to 4?wt%) was mixed with the dross and utilized to reinforce sintered composites. The milled powders were compacted then fired at various temperatures up to 700?°C. Physical properties in terms of bulk density and apparent porosity for sintered composites were tested using Archimedes method. SEM attached by energy dispersive spectrometer (EDS) was used to inspect microstructure and elemental analysis of sintered composites. Microhardness and compressive strength were also measured. Ultrasonic nondestructive technique was utilized to examine the elastic moduli. Electrical conductivity of sintered composite was also studied. During milling up to 20?h, Al₂O₃/Al core-shell was in-situ formed with size of 65.9 and 23.8?nm, respectively. The apparent porosity of sintered composites was improved with rising graphene percent while it decreased with increasing sintering temperature. Increasing of graphene mass percent and firing temperature led to remarkable increase in all mechanical properties and electrical conductivity. The maximum compressive strength, hardness, elastic modulus and electrical conductivity were 200?MPa, 1200?MPa, 215?GPa and 1.42?×?10^?5 S/m, respectively, obtained for composite sintered at 700?°C having 4?wt% graphene.