A new topology for nonisolated multiport zero voltage switching dc‐dc converter

In this paper, a new multiport zero voltage switching dc‐dc converter is proposed. Multiport dc‐dc converters are widely applicable in hybrid energy generating systems to provide substantial power to sensitive loads. The proposed topology can operate in 3 operational modes of boost, buck, and buck‐boost. Moreover, it has zero voltage switching operation for all switches and has the ability to eliminate the input current ripple; also, at low voltage side, the input sources can be extended. In addition, it has the ability of interfacing 3 different voltages only by using 3 switches. In this paper, the proposed topology is analyzed theoretically for all operating modes; besides, the voltage and current equations of all components are calculated. Furthermore, the required soft switching and zero input currents ripple conditions are analyzed. Finally, to demonstrate the accurate performance of the proposed converter, the Power System Computer Aided Design(PSCAD)/Electro Magnetic Transient Design and Control(EMTDC) simulation and experimental results are extracted and presented.     

A new interleaved bidirectional dc/dc converter with zero voltage switching and high voltage gain: analyses,design and simulation

In this paper, a new interleaved non‐isolated bidirectional dc–dc converter with capability of zero voltage switching and high voltage gain is proposed. In the proposed converter by using two coupled inductors and one capacitor, the voltage gain is extended. Moreover, by using only an auxiliary circuit that includes an inductor and two capacitors, the zero voltage switching (ZVS) of two used switches in the first phase of converter can be achieved. The ZVS operation of two used switches in the second phase is always obtained without using any extra auxiliary circuit. This converter similar to other interleaved converters has low input current ripple and low current stress on switches. In this paper, the proposed converter is analyzed in all operating modes, and also the voltage gain, required conditions for ZVS operation of switches, voltage and current stresses of all switches, and the value of input current ripple in both boost and buck operations are obtained. Finally, the accuracy performance of the proposed converter is verified through simulation results in EMTDC/PSCAD software. Copyright © 2017 John Wiley & Sons, Ltd.     

A high‐voltage gain nonisolated noncoupled inductor based multi‐input DC‐DC topology with reduced number of components for renewable energy systems

This paper proposes a modular nonisolated noncoupled inductor‐based high‐voltage gain multi‐input DC‐DC converter. Despite the high‐voltage gain of the proposed topology, the average of normalized voltage stress (NVS) on its switches/diodes is low. This property leads to less loss and cost of switches/diodes. Using the same number of components, the proposed topology produces higher voltage gains, in comparison with recently presented high step‐up topologies. Also, the proposed topology utilizes less number of components (capacitors, inductors, diodes, and switches) for producing a desired voltage gain, which can reduce the size, mass, cost, complexity, and losses and improve the efficiency of converter. Continuous current of input sources is another main advantage of the proposed topology. All the abovementioned characteristics have made the proposed topology very suitable for renewable energy systems (or even hybrid/electric vehicles). Design considerations of the proposed topology have also been presented. For better evaluation, the proposed topology has been compared with some of recently presented high step‐up structures, from viewpoints of producible voltage gain, number of components, and normalized voltage stress (NVS) on switches/diodes. Finally, the prototype of 2‐input version has been experimentally implemented. Obtained experimental results confirm appropriate performance of the proposed topology.     

A new non‐isolated free ripple input current bidirectional DC‐DC converter with capability of zero voltage switching

In this paper, a new nonisolated free ripple input current bidirectional dc‐dc converter with capability of zero voltage switching (ZVS) is proposed. The free ripple input current condition at low voltage side is achieved by using third winding of a coupled inductor and a capacitor for the whole range of duty cycles. In the proposed structure, the voltage conversion ratio can be more increased by adding the turn ratio of the second winding of the coupled inductor for the whole range of duty cycles. By adjusting the value of an auxiliary inductor in the topology of the converter, according to the power, the ZVS operation of the implemented 2 switches can be achieved throughout the whole power range. The mentioned features of proposed converter are validated theoretically for both boost and buck operations. In this paper, the proposed converter is analyzed for all operating modes. Moreover, all equations of the voltages and currents of all components, voltage conversion ratio, the required conditions for ZVS operation of switches, and also required conditions for canceling input current ripple at low voltage side are obtained. Finally, the performance of the proposed converter is reconfirmed through experimental and EMTDC/PSCAD simulation results.     

A new single‐phase high‐power‐factor converter with buck and buck–boost hybrid operation

In recent years, a wide variety of high‐power‐factor converter schemes have been proposed to solve the harmonic problem. The schemes are based on conventional boost, buck, or buck–boost topology, and their performance, such as output voltage control range in the boost and buck topology or efficiency in the buck–boost topology, is limited. To solve this, the authors propose a single‐phase high‐power‐factor converter with a new topology obtained from a combination of buck and buck–boost topology. The power stage performs the buck and buck–boost operations by a compact single‐stage converter circuit while the simple controller/modulator appropriately controls the alternation of the buck and buck–boost operation and maintains a high‐quality input current during both the buck and buck–boost operations. The proposed scheme results in a high‐performance rectifier with no limitation of output voltage control range and a high efficiency. In this paper, the principle and operation of the proposed converter scheme are described in detail and the theory is confirmed through experimental results obtained from 2‐kW prototype converter. © 2000 Scripta Technica, Electr Eng Jpn, 131(3): 91–100, 2000     

LLC resonant DC–DC converter with series‐connected primary windings of transformer

This paper proposes a zero‐voltage switching (ZVS) LLC resonant step up DC–DC converter with series‐connected primary windings of the transformer. The series resonant inverter in the proposed topology has two power switches (MOSFETs), two resonant capacitors, two resonant inductors, and only one transformer with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. Resonant capacitors and inductors along with the primary windings of the transformer form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with an interleaved half switching cycle. The secondary winding of transformer is connected to a bridge rectifier circuit to rectify the output voltage. The converter operates within a narrow frequency range below the resonance frequency to achieve ZVS, and its output power is regulated by pulse frequency modulation. The converter has lower conduction and switching losses and therefore higher efficiency. The experimental results of a 500‐W prototype of proposed converter are presented. The results confirm the good operation and performance of the converter. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A new control method of a resonant switched‐capacitor converter and the application for balancing of the split DC voltages in a multilevel inverter

This paper proposes a new voltage‐balancing circuit for the split DC voltages in a diode‐clamped five‐level inverter. The proposed circuit is based on a resonant switched‐capacitor converter (RSCC), which consists of two half‐bridge inverters, a resonant inductor, and a resonant capacitor. A new phase‐shift control of the RSCC is proposed to improve voltage balancing performance. Theoretical analysis reveals the rating of the RSCC and stored energy in the resonant inductor. Experimental results confirm the reduction of the inductor to one‐tenth in volume compared to a conventional voltage‐balancing circuit based on buck‐boost topology. Moreover, the proposed phase‐shift control has demonstrated that it is possible to eliminate the voltage deviation between the DC capacitors. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 168(2): 69–79, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20719     

A novel active‐clamp zero‐voltage‐switching buck‐boost converter

An active‐clamp zero‐voltage‐switching (ZVS) buck‐boost converter is proposed in this paper to improve the performance of converter in light load condition. By employing a small resonant inductor, the ZVS range of switches could be adjusted to very light load condition. Moreover, 2 clamping capacitors are added in the converter to eliminate the voltage spike on the switches during transition. The operating principle of the proposed converter is analyzed, and the optimal design guide for full range ZVS is also provided. A 60‐W output prototype is experimentally built and tested in laboratory to verify the feasibility of proposed converter. The measured results show the critical ZVS operation of power switches at 1 and 0.7‐W output power for buck and boost mode, respectively. The peak conversion efficiency is up to 92.3%.     

High‐power‐factor single‐switch AC to DC converter for LED lighting

In this paper, we report a novel single‐switch AC to DC step‐down converter suitable for light emitting diodes. The proposed topology has a buck and a buck–boost converter. The circuit is designed to operate in the discontinuous conduction mode in order to improve the power factor. In this topology, a part of the input power is connected to the load directly. This feature of the proposed topology increases the efficiency of power conversion, improves the input power factor, produces less voltage stress on intermediate stages, and reduces the output voltage in the absence of a step‐down transformer. The theoretical analysis, design procedure, and performance of the proposed converter are verified by simulation and experiment. A 36 V, 60 W prototype has been built to demonstrate the merits of this circuit. © 2017 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Step-up Transformerless Seven-level DC-AC Hybrid Topology for Interconnection of Renewable-based DC Sources to Microgrids

This article introduces a new step-up transformerless multi-level DC-AC hybrid topology for interconnecting renewable DC sources to loads or microgrids. This enabling technology incorporates the best characteristics of three modified basic topologies—a DC-DC multi-level boost converter, a DC-DC multi-level buck converter, and an H-bridge—to obtain a seven-level step-up DC-AC hybrid structure using only one DC input and nine power switches for a single-phase output with field-programmable gate array based control. The advantages of the step-up seven-level structure compared to other proposals are higher efficiency, a reduced number of power switches, and high power density associated with transformerless characteristic. Furthermore, in contrast to conventional topologies, the proposed design does not require voltage/current monitoring of the capacitors or a capacitor-balancing control scheme, and only one DC source input is used. Consequently, a high-performance configuration is obtained. The laboratory results demonstrate the validity of the design and the performance of the prototype.     

A new arrangement of Z‐source AC–AC converter and its closed‐loop control system

In this study, a Z‐source alternating current‐to‐alternating current (AC–AC) converter with a specific topology, which can provide both buck and boost modes, is investigated. This converter, which can be implemented easily, utilizes only two switches with complemented commands. A comparison between the Z‐source AC–AC converter and a conventional thyristor voltage controlled one is presented here, and it shows that in the most areas, the Z‐source converter provides a faster response and lower total harmonic distortion of the output currents than the conventional one. Moreover, the Z‐source converter is also extended to the multiphase systems. In addition, a new arrangement of this converter is proposed here to remove the isolated single‐phase sources. Furthermore, an open‐loop method is proposed for soft‐starting applications. Finally, a closed‐loop control system is also suggested for a three‐phase Z‐source converter to soft start and control the speed of an induction motor. Computer simulations show the validity and effectiveness of the proposed schemes. Copyright © 2014 John Wiley & Sons, Ltd.     

Single Switch DC-DC Boost Converter using Diode-Capacitor Module and Capacitor-Inductor-Capacitor Lift

ABSTRACT–

This article presents a single switch DC-DC boost converter using diode-capacitor (DC) modules and capacitor-inductor-capacitor (CLC) lifts. This topology can step-up the voltage of battery-input sources and power the DC-voltage bus of practical applications. The output voltage is the superposition of the voltage of capacitors in each module and inductors in each lift. Operational modes in on-off state can largely increase the step-up ratio of the proposed converter. The voltage gain of the circuit has a wide range with only one switch to control the operation of it. In addition, the extended circuit with multi-module and multi-lift is also derived and analyzed in this article to expand the potential application of the proposed topology. The steady-state characteristics of the proposed circuit are presented in detail in this article. Hardware-based circuit employing one module and one lift will be tested using a battery and experimental results can verify the potential value of this design.     

Single‐stage single‐switch PFC converter for wide‐input extreme step‐down voltage applications

This paper presents a new single‐stage single‐switch high power factor correction AC/DC converter suitable for low‐power applications (< 150 W) with a universal input voltage range (90–265 V_rms). The proposed topology integrates a buck–boost input current shaper followed by a buck and a buck–boost converter, respectively. As a result, the proposed converter can operate with larger duty cycles compared with the existing single‐stage single‐switch topologies, hence, making them suitable for extreme step‐down voltage conversion applications. Several desirable features are gained when the three integrated converter cells operate in discontinuous conduction mode. These features include low semiconductor voltage stress, zero‐current switch at turn‐on, and simple control with a fast well‐regulated output voltage. A detailed circuit analysis is performed to derive the design equations. The theoretical analysis and effectiveness of the proposed approach are confirmed by experimental results obtained from a 100‐W/24‐V_dc laboratory prototype. Copyright © 2011 John Wiley & Sons, Ltd.     

A Multi-Functional Single-Stage Power Electronic Interface for Plug-In Electric Vehicles Application

This paper proposes a Zeta-derived non-isolated single-stage power electronic interface for on-board application of plug-in electric vehicles, which provides all modes (plug-in charging, propulsion, and regenerative braking) of vehicle operation. In addition, the proposed converter can charge the battery through universal input voltage range, i.e., 90–260 V due to buck/boost operations in plug-in charging mode. In propulsion and regenerative braking modes, the proposed converter operates as conventional boost and buck DC/DC converter, respectively. Compared to existing single-stage converters, the proposed converter has least components to those converters which have buck/boost operation in plug-in charging mode. A voltage/current stresses and loss analysis of the converter have been investigated for each mode of converter operation. Detailed simulation and experimental results are given to show the effectiveness of the proposed converter.     

A ZVS‐ZCS phase shift full bridge DC‐DC converter with secondary‐side control for battery charging applications

The output power requirement of battery charging circuits can vary in a wide range, hence making the use of conventional phase shift full bridge DC‐DC converters infeasible because of poor light load efficiency. In this paper, a new ZVS‐ZCS phase shift full bridge topology with secondary‐side active control has been presented for battery charging applications. The proposed circuit uses 2 extra switches in series with the secondary‐side rectifier diodes, operating with phase shift PWM. With the assistance of transformer's magnetizing inductance, the proposed converter maintains zero voltage switching (ZVS) of the primary‐side switches over the entire load range. The secondary‐side switches regulate the output voltage/current and perform zero current switching (ZCS) independent of the amount of load current. The proposed converter exhibits a significantly better light load efficiency as compared with the conventional phase shift full bridge DC‐DC converter. The performance of the proposed converter has been analyzed on a 1‐kW hardware prototype, and experimental results have been included.     

Single‐Inductor Dual‐Output DC–DC Converter Design Using RC Ripple Regulator Method

In this paper, we have proposed Single‐Inductor Dual‐Output (SIDO) buck–buck and boost–boost dc–dc converter using improved RC ripple regulator control. The proposed SIDO buck–buck converter has the characteristics of low‐ripple and high control frequency. RC ripple regulator control cannot be applied to SIDO boost–boost converter because RC ripple regulator undergoes self‐excited oscillation and two self‐excited oscillating controllers make the SIDO converter unstable. Thus we proposed the priority circuit for RC ripple regulator control. The proposed control circuit improves response characteristic and simplicity of the control circuit. Simulations are performed to verify the validity of the proposed SIDO converter. Simulation results indicate good performance of the proposed SIDO converter.     

Output current ripple reduction of LED driver using ceramic‐capacitor‐input circuit and buck‐boost converter

This article proposes an LED driver that consists of a ceramic‐capacitor‐input rectifier and a buck‐boost converter. The LED driver has an advantage of long life because it does not contain any electrolytic capacitors. However, the issue with electrolytic capacitor‐less LED driver is that the ripple of the smoothed voltage becomes large due to insufficient capacitance of the smoothing capacitor. The proposed method, which uses the discontinuous current mode of a buck‐boost converter, reduces the output current ripple under such conditions. Experimental results using a 5.7 W LED driver prototype demonstrate that the proposed method reduces the output current ripple and that the percent flicker becomes 4.4%, which is smaller than the recommended upper limit of 8%.     

An interleaved high step‐up DC‐DC converter with double boost paths

This paper proposed a novel high step‐up converter with double boost paths. The circuit uses two switches and one double‐path voltage multiplier cell to own the double boost and interleaved effects simultaneously. The voltage gain ratio of the proposed DC‐DC converter can be three times the ratio of the conventional boost converter such that the voltage stress of the switch can be lower. The high step‐up performance is in accordance with only one double‐path voltage multiplier cell. Therefore, the number of diodes and capacitors in the proposed converter can be reduced. Furthermore, the interleaved property of the proposed circuit can reduce the losses in the rectifier diode and capacitor. The prototype circuit with 24‐V input voltage, 250‐V output voltage, and 150‐W output power is experimentally realized to verify the validity and effectiveness of the proposed converter. Copyright © 2014 John Wiley & Sons, Ltd.     

Analysis and implementation of a high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter

A high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter with ripple‐free input current is presented. In the presented converter, the ripple‐free boost cell provides ripple‐free input current and zero‐voltage switching of power switches. The resonant flyback cell provides zero‐voltage switching of power switches and zero‐current switching of the output diode. Also, it has a simple output stage. The proposed converter achieves high efficiency because of the reduction of the switching losses of the power switches and the output diode. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed and its experimental results are presented for validation. Copyright © 2011 John Wiley & Sons, Ltd.     

Non-isolated high step-up dual-input DC-DC converter with zero-voltage transition

In this paper, a non-isolated dual-input DC-DC converter with zero-voltage transition (ZVT) is proposed for renewable energy systems. The proposed converter has high step-up conversion gain without using any transformer or coupled inductors. The proposed structure consists of two boost cells, one diode-capacitor multiplier cell, and one ZVT auxiliary circuit. The main switches turn on and off under zero voltage condition and the auxiliary switch turns on under zero current condition and turns off under zero current and zero voltage conditions. Soft switching conditions, high efficiency, continuous current of input sources, low-voltage stress on switches, and returning the energy of the auxiliary circuit to the boost cell connected to the lower-voltage input are the main advantages of the proposed converter. The steady-state analysis of the converter and operation intervals are discussed. A 160-W prototype of the proposed converter is designed and implemented. Experimental results confirm the theoretical analysis. The efficiency reaches 96.7% at the nominal load by providing soft-switching for all switches. The proposed topology can be extended for multi-input applications by expanding the number of diode-capacitor multiplier and input boost cells.