Supercapacitive properties of a nanowire-structured MnO2 electrode in the gel electrolyte containing silica

Nanowire-structured MnO₂ active materials were prepared by a chemical precipitation method and their supercapacitive properties for use in the electrodes of supercapacitors were investigated by means of cyclic voltammetry in an aqueous gel electrolytes consisting of 1 M Na₂SO₄ and fumed silica (SiO₂). The MnO₂ electrode showed a maximum specific capacitance of 151 F g⁻¹ after 1000 cycles at 100 mV s⁻¹ when using the gel electrolyte containing 3 wt.% of SiO₂, which is higher than 121 F g⁻¹ obtained when using the 1 M Na₂SO₄ liquid electrolyte alone.     

Nanosized α-LiFeO2 as electrochemical supercapacitor electrode in neutral sulfate electrolytes

In this work we have explored the electrochemical properties of two lithiated iron oxide powders for supercapacitor purposes. These samples mainly consisted of α-LiFeO₂ in nanosized or micrometric form. Electrolyte was an aqueous 0.5 M Li₂SO₄ solution and voltage range studied was between 0 and −0.7 V vs. a Ag/AgCl reference electrode. As expected, electrochemical performance was dependent on the particle size. When electrolyte was deaerated a stable capacitance of ≈50 F g⁻¹ is provided by the nanosized sample for several hundred cycles. Other sulfate based salts (Na₂SO₄, K₂SO₄, Cs₂SO₄) were investigated as electrolytes but only Li₂SO₄ leads to a stable capacitance upon cycling, probably due to lithium intercalation. An hybrid cell consisting of this sample and MnO₂ as negative and positive electrodes, respectively, delivered 0.3 F cm⁻² (10 F g⁻¹). Although these values are lower than reported for other aqueous hybrid cell, α-LiFeO₂/MnO₂ asymmetric capacitor is interesting from both, an economic and an environmental point of view.     

Synthesis and electrical properties of the (PVA)0.7(KI)0.3·xH2SO4 (0 ≤ x ≤ 5) polymer electrolytes and their performance in a primary Zn/MnO2 battery

Solid acid polymer electrolytes (SAPE) were synthesised using polyvinyl alcohol, potassium iodide and sulphuric acid in different molar ratios by solution cast technique. The temperature dependent nature of electrical conductivity and the impedance of the polymer electrolytes were determined along with the associated activation energy. The electrical conductivity at room temperature was found to be strongly depended on the amorphous nature of the polymers and H₂SO₄ concentration. The ac (100 Hz to 10 MHz) and dc conductivities of the polymer electrolytes with different H₂SO₄ concentrations were analyzed. A maximum dc conductivity of 1.05 × 10⁻³ S cm⁻¹ has been achieved at ambient temperature for electrolytes containing 5 M H₂SO₄. The frequency and temperature dependent dielectric and electrical modulus properties of the SAPE were studied. The charge transport in the present polymer electrolyte was obtained using Wagner's polarization technique, which demonstrated the charge transport to be mainly due to ions. Using these solid acid polymer electrolytes novel Zn/SAPE/MnO₂ solid state batteries were fabricated and their discharge capacity was calculated. An open circuit voltage of 1.758 V was obtained for 5 M H₂SO₄ based Zn/SAPE/MnO₂ battery.     

Electrolytes for hybrid carbon-MnO2 electrochemical capacitors

Different aqueous-based electrolytes have been tested in order to improve the electrochemical performance of hybrid (asymmetric) carbon/MnO₂ electrochemical capacitor (EC). Chloride and bromide aqueous solutions lead to the formation of Cl₂ and Br₂ respectively upon oxidation of the corresponding salt, thus limiting the useful electrochemical window of the MnO₂ electrode and producing gas evolution (in the case of chloride salts) detrimental to the cycling ability of an hybrid device. For sulfate and nitrate salts, MnO₂ electrode exhibits a 20% increase in capacitance when lithium is used as the cation compared to sodium or potassium salts, probably due to partial lithium intercalation in the tunnels of α-MnO₂ structure. The higher ionic conductivity and solubility of LiNO₃ has led to the investigation of this electrolyte in carbon/MnO₂ supercapacitor compared to standard hybrid cell using K₂SO₄. A lower resistance increase was evidenced when the temperature was decreased down to −10 °C. Long term cycling ability of carbon/MnO₂ supercapacitor was also evidenced with 5 M LiNO₃ electrolyte.     

A novel LiTi2(PO4)3/MnO2 hybrid supercapacitor in lithium sulfate aqueous electrolyte

In this work, carbon-coated lithium-ion intercalated compound LiTi₂(PO₄)₃ and MnO₂ have been synthesized and they deliver a capacity of 90 and 60 mAh/g in 1 M Li₂SO₄ neutral aqueous electrolyte within safe potentials without O₂ and H₂ evolution, respectively. The novel hybrid supercapacitor in which MnO₂ was used as a positive electrode and carbon-coated LiTi₂(PO₄)₃ as a negative electrode was assembled and the LiTi₂(PO₄)₃/MnO₂ hybrid supercapacitor showed a sloping voltage profile from 0.7 to 1.9 V, at an average voltage near 1.3 V, and delivers a capacity of 36 mAh/g and an energy density of 47 Wh/kg based on the total weight of the active electrode materials. It exhibits a desirable profile and maintains over 80% of its initial energy density after 1000 cycles. The hybrid supercapacitor also exhibit an excellent rate capability, even at a power density of 1000 W/kg, it has a specific energy 25 Wh/kg compared with 43 Wh/kg at the power density about 200 W/kg.     

Hot corrosion behaviors of gas tunnel type plasma sprayed La2Zr2O7 thermal barrier coatings

Gas tunnel type plasma sprayed free-standing La₂Zr₂O₇ coating specimens with a thickness of 300-400 μm were prepared under optimized operating conditions and were subjected to hot corrosion test in the presence of corrosive impurities such as V₂O₅, Na₂SO₄, and Na₂SO₄ + V₂O₅ mixtures (60:40 wt%) at two different temperatures for duration of 5 h, i.e. 1000 and 1350 K for V₂O₅ and Na₂SO₄ + V₂O₅ mixtures, 1200 and 1350 K for Na₂SO₄. For temperatures at 1350 K, the reaction mechanism of V₂O₅ and the mixture of Na₂SO₄ + V₂O₅ are similar and LaVO₄ is formed as the corrosive product, which leads to massive phase transformation from pyrochlore to tetragonal and monoclinic phases. Microstructural observations from planar reaction zone (PRZ) and melt infiltrated reaction zone (MIRZ) reveals that the present La₂Zr₂O₇ coating exhibits good hot corrosion resistance in V₂O₅ environment and moderate for the mixture of Na₂SO₄ + V₂O₅, but is worst in Na₂SO₄ environment.     

The Preparation and Characterization of High-Strength PMMA-Na2SO4 Composite Film

PMMA-Na₂SO₄ composite films were prepared by a solvent casting method and were characterized by SEM, EDX, DSC, UTM, TG/DTA and FTIR techniques. From the SEM it is clear that Na₂SO₄ were well dispersed, having sizes ranging from micrometer to nanometer. EDX results confirm the presence of Na₂SO₄ particles in a polymer matrix. UTM studies show that the tensile strength of PMMA-Na₂SO₄ composite is better than pure PMMA. FTIR spectra indicates the strong interaction between C=O of PMMA and Na₂SO₄. According to DSC, TG/DTA analysis the thermal stability and glass transition temperature of PMMA-Na₂SO₄ has increased as compared with that of pure PMMA.     

Catalytic removal of NO in waste incineration processes over Rh/Al2O3 and Rh–Na/Al2O3: Effects of particulates,heavy metals,SO2 and HCl

Two novel catalysts Rh/Al₂O₃ and Rh–Na/Al₂O₃ were prepared for NO removal and tested their practical performances in a laboratory-scale waste incineration system. The effects of particulates, heavy metals, and acid gases on the catalysts were evaluated and investigated through several characterization techniques, such as SEM, EA, XRPD, ESCA, and FTIR. The results indicated that the NO conversions were increased with the accumulation of particulates on the surface of catalysts, which was attributed to the increase in carbon content. However, the increase in heavy metals Cd and Pb contents on the surface of catalysts decreased the activity of catalyst for NO removal but did not change the chemical state of Rh and Na. The Rh/Al₂O₃ catalysts were poisoned when the acid gases SO₂ and HCl were present in the flue gas, because Rh and Al reacted with S and Cl to form inactive products. Adding Na to Rh/Al₂O₃ catalysts produced a promoting effect for SO₂ removal due to the formation of Na₂SO₄. The influence levels of different pollutants on the performances of Rh/Al₂O₃ and Rh–Na/Al₂O₃ catalysts for NO removal followed the sequence of HCl > heavy metals > SO₂ > particles.     

Polypyrrole and La1−xSrxMnO3 (0≤ x ≤0.4) composite electrodes for electroreduction of oxygen in alkaline medium

Composite G/PPy/PPy(La_1−xSr_xMnO₃)/PPy electrodes made of the perovskite La_1−xSr_xMnO₃ embedded into a polypyrrole (PPy) layer, sandwiched between two pure PPy films, electrodeposited on a graphite support were investigated for electrocatalysis of the oxygen reduction reaction (ORR). PPy and PPy(La_1−xSr_xMnO₃) (0≤ x ≤0.4) successive layers have been obtained on polished and pretreated graphite electrodes following sequential electrodeposition technique. The electrolytes used in the electrodeposition process were Ar saturated 0.1 mol dm⁻³ pyrrole (Py) plus 0.05 mol dm⁻³ K₂SO₄ with and without containing a suspension of 8.33 g L⁻¹ oxide powder. Films were characterized by XRD, SEM, linear sweep voltammetry, cyclic voltammetry (CV) and electrochemical impedance (EI) spectroscopy. Electrochemical investigations were carried out at pH 12 in a 0.5 mol dm⁻³ K₂SO₄ plus 5 mmol dm⁻³ KOH, under both oxygenated and deoxygenated conditions. Results indicate that the porosity of the PPy matrix is considerably enhanced in presence of oxide particles. Sr substitution is found to have little influence on the electrocatalytic activity of the composite electrode towards the ORR. However, the rate of oxygen reduction decreases with decreasing pH of the electrolyte from pH 12 to pH 6. It is noteworthy that in contrast to a non-composite electrode of the same oxide in film form, the composite electrode exhibits much better electrocatalytic activity for the ORR.     

Study of the preasphaltenes of coal liquefaction and its hydro-conversion kinetics catalyzed by SO4/ZrO2

The investigation of hydro-conversion behavior of the heavy intermediate products derived from coal direct liquefaction is advantageous to optimize the technological conditions of direct coal liquefaction and improve the oil yield. In this paper, the hydro-conversion of preasphaltenes catalyzed by SO₄²⁻/ZrO₂ solid acid was investigated based on the structural characterization of preasphaltenes and its hydro-conversion products, and the determination of products distribution and the kinetics of preasphaltenes hydro-conversion. The results indicated that the content of condensed aromatic rings increased, and the contents of hydrogen, oxygen and aliphatic side chains of preasphaltenes decreased with the increase of coal liquefaction temperature. The preasphaltenes showed higher hydro-conversion reactivity while SO₄²⁻/ZrO₂ solid acid was used as catalyst. Higher temperature and longer time were in favor of increasing the conversion and the oil + gas yield. The conversion of preasphaltenes hydro-conversion under 425 °C, for 40 min reached 81.3% with 51.2% oil + gas yield. SO₄²⁻/ZrO₂ solid acid was in favor of the catalytic cracking rather than the catalytic hydrogenation in the hydro-conversion of preasphaltenes. The activation energy of preasphaltenes conversion into asphaltenes was 72 kJ/mol. The regressive reactions were only observed at a higher temperature.     

Mn3O4 nanoparticles embedded into graphene nanosheets: Preparation, characterization, and electrochemical properties for supercapacitors

Mn₃O₄/graphene nanocomposites were synthesized by mixing graphene suspension in ethylene glycol with MnO₂ organosol, followed by subsequent ultrasonication processing and heat treatment. The as-prepared product consists of nanosized Mn₃O₄ particles homogeneously distributed on graphene nanosheets, which has been confirmed by field emission scanning electron microscopy and transmission electron microscopy analysis. Atomic force microscope analysis further identified the distribution of dense Mn₃O₄ nanoparticles on graphene nanosheets. When used as electrode materials in supercapacitors, Mn₃O₄/graphene nanocomposites exhibited a high specific capacitance of 175 F g⁻¹ in 1 M Na₂SO₄ electrolyte and 256 F g⁻¹ in 6 M KOH electrolyte, respectively. The enhanced supercapacitance of Mn₃O₄/graphene nanocomposites could be ascribed to both electrochemical contributions of Mn₃O₄ nanoparticles, functional groups attached to graphene nanosheets, and significantly increased specific surface area.     

Cation driven actuation for free standing PEDOT films prepared from propylene carbonate electrolytes containing TBACF3SO3

Free standing PEDOT [poly(3,4-ethylenedioxythiophene)] films (with surface conductivities of 200-400 S cm⁻¹) were generated in tetrabutylammonium trifluromethanesulfonate (TBACF₃SO₃) electrolytes by potentiostatic (E_P 1.05 V vs. Ag wire) electropolymerisation in propylene carbonate (at −27 °C) and methyl benzoate (at −4 °C). Films obtained in the TBACF₃SO₃ electrolytes showed a length increase of 2-3% during scans to negative potentials under isotonic (constant load 1.35 MPa) and stress of 0.3 MPa under isometric (constant length) conditions. Cation movement occurred due to immobilisation of CF₃SO₃⁻ anions during electropolymerisation. The system showed good stability and low creep during square wave electrochemical cycling in the potential range from 0.0 to 1.0 V. The surface morphology (SEM) of the PEDOT films showed that the polymer structure is dependent upon the solvent used during the polymerisation process.     

Factors influencing the structure of electrochemically prepared α-MnO2 and γ-MnO2 phases

The α- and γ-phases of MnO₂ prepared by electrolysis of MnSO₄ and M_xSO₄ (where M = Li⁺, Na⁺, K⁺, Rb⁺, Cs⁺ or Mg²⁺) in aqueous solutions at various pH and voltage E_v values under ambient conditions have been systematically studied. The structures of powdery MnO₂ produced are found to depend on the radius of the M^z+ counter cation in addition to the pH and E_v conditions. In order to achieve the α-phase for MnO₂ formation under neutral pH condition, the radius of counter cation must be equal to or greater than 1.41 Å, the size of the K⁺ cation. The relative concentration ratio of [MnO₄⁻]_transient/[Mn²⁺], which is related to the pH-E_v conditions, also affects the structure of MnO₂ produced with counter ions smaller than K⁺. For samples prepared in acidified solution with the counter ions of Li⁺, Na⁺ or Mg²⁺ at 2.2 V, the electrolysis products display the γ-MnO₂ phase while those prepared at 2.8 V electrolysis produce a mixture of γ-MnO₂ and α-MnO₂ phases. Single phase of α-MnO₂ is identified in the 5 V electrolysis products. Furthermore, the valence state of manganese was found to decrease as the applied voltage was reduced from 5.0 to 2.2 V. This implies that the lower [MnO₄⁻]_transient/[Mn²⁺] ratio or the less oxidative condition is responsible for the non-stoichiometric MnO₂ structure with oxygen deficiency.     

Hydrothermal synthesis of LiMn2O4/C composite as a cathode for rechargeable lithium-ion battery with excellent rate capability

A spinel LiMn₂O₄/C composite was synthesized by hydrothermally treating a precursor of manganese oxide/carbon (MO/C) composite in 0.1 M LiOH solution at 180 °C for 24 h, where the precursor was prepared by reducing potassium permanganate with acetylene black (AB). The AB in the precursor serves as the reducing agent to synthesize the LiMn₂O₄ during the hydrothermal process; the excess of AB remains in the hydrothermal product, forming the LiMn₂O₄/C composite, where the remaining AB helps to improve the electronic conductivity of the composite. The contact between LiMn₂O₄ and C in our composite is better than that in the physically mixed LiMn₂O₄/C material. The electrochemical performance of the LiMn₂O₄/C composite was investigated; the material delivered a high capacity of 83 mAh g⁻¹ and remained 92% of its initial capacity after 200 cycles at a current density of 2 A g⁻¹, indicating its excellent rate capability as well as good cyclic performance.     

Advanced experimental analysis of the reaction of Ca(OH)2 with HCl and SO2 during the spray dry scrubbing process

This work evaluates both the removal efficiencies of HCl and SO₂ at different points in a spray dryer using Ca(OH)₂ as the absorbent. The operating conditions were specified in terms of the temperature of the flue gas (200-300 °C), the HCl concentration (120-1000 ppm), the SO₂ concentration (150-500 ppm) and the amount of CaCl₂ added (10-30 wt.%).The experimental results showed that the SO₂ removal efficiencies were higher in the presence of HCl (120-500 ppm) than in the absence of HCl at 250 °C and 20% relative humidity (RH). However, the removal efficiency of SO₂ decreased as the HCl concentration increased. The removal efficiency of SO₂ also increased with the amount of CaCl₂ in the spray dryer.     

Multiwall carbon nanotube supported poly(3,4-ethylenedioxythiophene)/manganese oxide nano-composite electrode for super-capacitors

MWCNT-PSS/PEDOT/MnO₂ nano-composite electrodes were fabricated by generating pseudo-capacitive poly(3,4-ethylenedioxythiophene) (PEDOT)/MnO₂ nano-structures on poly(styrene sulfonate) (PSS) dispersed multiwalled carbon nanotubes (MWCNTs). PSS dispersed MWCNTs (MWCNT-PSS) facilitated the growth of PEDOT and MnO₂ into nano-rods with large active surface area and good electrical conductivity. The ternary MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode was studied for the application in super-capacitors, and exhibited excellent capacitive behavior between −0.2 V and 0.8 V (vs. saturated Ag/AgCl electrode) with high reversibility. Specific capacitance of the nano-composite electrode was found as high as 375 F g⁻¹. In contrast, specific capacitance of MWCNT-PSS/MnO₂ and MWCNT-PSS nano-composite electrodes is 175 F g⁻¹ and 15 F g⁻¹, respectively. Based on cyclic voltammetric studies and cycle-life tests, the MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode gave a highly stable and reversible performance up to 2000 cycles. Our studies demonstrate that the synergistic combination of MWCNT-PSS, PEDOT and MnO₂ has advantages over the sum of the individual components.     

Performance evaluation of CNT/polypyrrole/MnO2 composite electrodes for electrochemical capacitors

A ternary composite of CNT/polypyrrole/hydrous MnO₂ is prepared by in situ chemical method and its electrochemical performance is evaluated by using cyclic voltammetry (CV), impedance measurement and constant-current charge/discharge cycling techniques. For comparative purpose, binary composites such as CNT/hydrous MnO₂ and polypyrrole/hydrous MnO₂ are prepared and also investigated for their physical and electrochemical performances. The specific capacitance (SC) values of the ternary composite, CNT/hydrous MnO₂ and polypyrrole/hydrous MnO₂ binary composites estimated by CV technique in 1.0 M Na₂SO₄ electrolyte are 281, 150 and 35 F g⁻¹ at 20 mV s⁻¹ and 209, 75 and 7 F g⁻¹ at 200 mV s⁻¹, respectively. The electrochemical stability of ternary composite electrode is investigated by switching the electrode back and forth for 10,000 times between 0.1 and 0.9 V versus Ag/AgCl at 100 mV s⁻¹. The electrode exhibits good cycling stability, retaining up to 88% of its initial charge at 10,000th cycle. A full cell assembled with the ternary composite electrodes shows a SC value of 149 F g⁻¹ at a current loading of 1.0 mA cm⁻² during initial cycling, which decreased drastically to a value of 35 F g⁻¹ at 2000th cycle. Analytical techniques such as scanning electron microscopy (SEM), X-ray diffraction spectroscopy (XRD), Brunauer-Emmet-Teller (BET) surface area measurement and inductively coupled plasma-atomic emission spectrometry (ICP-AES) are also used to characterize the composite materials.     

Synthesis and electrochemical performance of Li2FeSiO4/carbon/carbon nano-tubes for lithium ion battery

Li₂FeSiO₄/carbon/carbon nano-tubes (Li₂FeSiO₄/C/CNTs) and Li₂FeSiO₄/carbon (Li₂FeSiO₄/C) composites were synthesized by a traditional solid-state reaction method and characterized comparatively by X-ray diffraction, scanning electron microscopy, BET surface area measurement, galvanostatic charge-discharge and AC impedance spectroscopy, respectively. The results revealed that the Li₂FeSiO₄/C/CNT composite exhibited much better rate performance in comparison with the Li₂FeSiO₄/C composite. At 0.2 C, 5 C and 10 C, the former composite electrode delivered a discharge capacity of 142 mAh g⁻¹, 95 mAh g⁻¹, 80 mAh g⁻¹, respectively, and after 100 cycles at 1 C, the discharge capacity remained 95.1% of its initial value.     

Factors influencing MnO2/multi-walled carbon nanotubes composite's electrochemical performance as supercapacitor electrode

Poor crystallined α-MnO₂ grown on multi-walled carbon nanotubes (MWCNTs) by reducing KMnO₄ in ethanol are characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and Brunauer-Emmett-Telle (BET) surface area measurement, which indicate that MWCNTs are wrapped up by poor crystalline MnO₂ and BET areas of the composites maintain the same level of 200 m² g⁻¹ as the content of MWCNTs in the range of 0-30%. The electrochemical performances of the MnO₂/MWCNTs composites as electrode materials for supercapacitor are evaluated by cyclic voltammetry (CV) and galvanostatic charge-discharge measurement in 1 M Na₂SO₄ solution. At a scan rate of 5 mV s⁻¹, rectangular shapes could only be observed for the composites with higher MWCNTs contents. The effect of additional conductive agent KS6 on the electrochemical behavior of the composites is also studied. With a fixed carbon content of 25% (MWCNTs included), MnO₂ with 20% MWCNTs and 5% KS6 has the highest specific capacitance, excellent cyclability and best rate capability, which gives the specific capacitance of 179 F g⁻¹ at a scan rate of 5 mV s⁻¹, and remains 114.6 F g⁻¹ at 100 mV s⁻¹.     

Synthesis of highly crystalline spinel LiMn2O4 by a soft chemical route and its electrochemical performance

Highly crystalline spinel LiMn₂O₄ was successfully synthesized by annealing lithiated MnO₂ at a relative low temperature of 600 °C, in which the lithiated MnO₂ was prepared by chemical lithiation of the electrolytic manganese dioxide (EMD) and LiI. The LiI/MnO₂ ratio and the annealing temperature were optimized to obtain the pure phase LiMn₂O₄. With the LiI/MnO₂ molar ratio of 0.75, and annealing temperature of 600 °C, the resulting compounds showed a high initial discharge capacity of 127 mAh g⁻¹ at a current rate of 40 mAh g⁻¹. Moreover, it exhibited excellent cycling and high rate capability, maintaining 90% of its initial capacity after 100 charge-discharge cycles, at a discharge rate of 5 C, it kept more than 85% of the reversible capacity compared with that of 0.1 C.