Ni52Mn21+xGa27-x(x=0-5)磁性形状记忆合金的相变

研究了非化学计量成分的多晶Ni52Mn21+xGa27-x(x=0-5)系列合金的热弹性马氏体相变和磁相变.合金的马氏体相变温度Ms随Mn含量的增加而升高,当x＞4时,Ms已经升高到室温以上,而马氏体相变滞后△T随z的增大而减小;合金的磁相变温度TC随z增加而升高,但变化范围不大,在z＞2后,Tc保持在348 K左右.实验获得了一种具有实用前景的合金成分--Ni52Mn25Ga23合金,其马氏体相变温度在室温以上,相变滞后仅为5 K.     

无磁钻铤用Cr-Mn-Ni-N系高氮钢平衡凝固相变与析出行为

借助Thermo-Calc软件对无磁钻铤用Fe-(15~25)Cr-(15~25)Mn-(0~5)Ni-(0~1)Mo-(0~1)N-(0~0.8)C多元系高氮钢在凝固和冷却过程中的相变及析出行为进行研究。使用Thermo-Calc软件中的TCFE9数据库对该钢相图的垂直截面图进行计算,分析了Cr、Mn、Ni、Mo、N及C元素对无磁钻铤用高氮钢凝固及冷却过程中相变的影响,并得到了平衡凝固相变路径图。结果表明,增加Cr、Mn含量可显著提高合金中氮的溶解度,Mo元素可以微弱提高氮的溶解度,Ni、C元素显著降低氮的溶解度。Ni、C和N含量提高可扩大单相奥氏体相区,具有稳定奥氏体的作用,Cr、Mo与Mn元素缩小单相奥氏体相区,具有稳定铁素体的作用。N元素可以促进M₂(C,N)相析出,使M₂₃C₆相析出受到抑制。Cr、Mn元素可以促进Sigma相析出,C、N元素抑制Sigma相析出。M₂₃C₆相的析出主要受C含量的影响,随着C含量的升高,M₂₃C₆相的析出温度显著升高。     

单晶Ni_(52)Mn_(24)Ga_(24)的磁感生应变和磁增强双向形状记忆效应

铁磁性Heusler合金Ni2 MnGa是近年开发的磁控制功能材料 ,已发现该材料结合马氏体相变可以产生大磁致伸缩 (磁感生应变 )和磁控制形状记忆效应两种应用功能。用磁悬浮冷坩埚提拉设备沿 [0 0 1]方向生长了组分为Ni52 Mn2 4 Ga2 4 的单晶。室温时沿该单晶样品 [0 0 1]方向加磁场 ,在该方向获得了 - 0 6 %的大磁感生应变。当磁场方向垂直于 [0 0 1]方向时 ,样品在 [0 0 1]方向的磁感生应变值为 0 5 %。同时该单晶样品在室温附近还具有可由磁场增强和控制的双向形状记忆效应。无磁场作用时 ,降低温度 ,样品在发生马氏体相变时 ,在 [0 0 1]方向产生1 2 %的收缩形变。随后升高温度 ,反马氏体相变时样品以同样的应变量膨胀 ,恢复到原来的形状 ,显示了特有的无需外应力协助的自发的双向形状记忆效应。其温度滞后只有 10℃。如果在样品的 [0 0 1]方向加一个偏磁场 ,其形状记忆的应变量随磁场的增强而增大。在磁场为 1 2T时可达 4%。而当磁场转向 [10 0 ]方向时 ,形状记忆的应变可以改变符号。本文指出产生大磁感生应变和磁增强双向形状记忆效应的关键是马氏体变体的择优取向。     

600°C热处理时Al-4Ni-2Mn合金中Al_9(Mn,Ni)_2共晶相的相变行为（英文）

采用扫描电子显微镜和透射电子显微镜研究600°C热处理时Al-4Ni-2Mn合金中Al_9(Mn,Ni)_2共晶相的形貌演变及相结构转变。结果表明:在热处理过程中,纤维状的Al_9(Mn,Ni)_2共晶相几乎全部转变成了椭球状和球状颗粒。而且,随着热处理时间的延长,共晶区的Al_9(Mn,Ni)_2颗粒发生了Oswald熟化现象。此外,通过研究证实热处理过程中的确存在由Al_9(Mn,Ni)_2到O相的相变过程。发生了相变的颗粒形貌表明:O相优先在Al_9(Mn,Ni)_2相的特定晶面上形核,然后沿一定方向朝母相生长。在相变过程中,由于O相的(010)[001]滑移系被激活,因此,在一些O相颗粒表面出现了滑移迹线。     

哈斯勒合金Ni_(46)Cu_4Mn_(38)Sn_(12)的相变应变与磁感生应变

通过结构、磁性以及应变测量,研究哈斯勒合金Ni46Cu4Mn38Sn12在马氏体相变过程中的相变应变与磁感生应变。结果表明:样品在马氏体相变过程中表现出一个接近0.12%的相变应变,几乎是目前研究所报道的三元哈斯勒合金Ni-Mn-Sn相变应变的3倍;此外,在等温条件下,通过外加磁场的诱导,获得了该样品在反马氏体相变起始温度点(284 K)的一个大的磁感生应变,这种行为可归结为马氏体与奥氏体相之间界面的磁弹耦合。     

Ga-Mn-Ni-Co磁驱动形状记忆合金的组织结构与相变

研究了Co掺杂对Ga2 MnNi磁性记忆合金马氏体相变行为、显微组织结构以及磁性能等的影响.结果表明:Co含量对Ga50 Mn25 Ni25xCox系列合金马氏体相变温度和晶格常数具有明显影响.Co原子数分数小于0.5％时,随着Co含量的增加,马氏体相变温度无显著变化,当Co原子数分数大于0.5％时,马氏体相变温度下降...     

Ni48Mn33Ga19合金的马氏体相变和磁性形状记忆效应

铁磁性Heusler型合金Ni2MnGa是近年来开发的新型磁控制功能材料，但其马氏体相变温度通常远远低于室温，不利于实际应用。本文研究了多晶Ni48Mn33Ga19合金的马氏体相变特征，发现该合金的马氏体相变温度已提高到室温以上。在室温下，分别测量了不同条件下制备的试样的磁场诱发应变，提出了增大材料磁致应变的有效方法。     

Ni50Mn26Ga24-yFey（y=0-23）磁性形状记忆合金的相变

制备了以Fe代Ga的Ni50Mn26Ga24-yFey（y=0-23）系列合金，研究了掺杂元素Fe对合金的马氏体相变温度、居里温度及相结构的影响，确定了合金成分与相变之间的变化规律。结果表明：掺杂元素Fe对Ni-Mn-Ga合金的马氏体相变的影响较为显著，当Fe含量（原子分数，下同）y≥12时，合金不显示热弹性马氏体相变过程，在具有母相结构的基础上有明显的第二相析出。合金的M5随Fe含量的增加而增加，合金的Tc随e／a的增大而增大。     

《金属功能材料》2004年（第11卷）总目录

·试验研究·Fe78- 2xCrxMoxSn2 P10 Si4 B4 C2 (x =2 ,4 )块体非晶合金　的制备和性能张　亮等 (1- 1)…………………化学沉积Co Fe P纳米涂层结构与磁学性能研究　马　杰等 (1- 4)…………………………………多晶Ni Mn Ga磁性记忆合金中间马氏体相变研究　赵增祺等 (1- 9)…………………………………Fe中刃型位错芯的模型建立及电子结构研究　党宏丽等 (1- 14 )…………………………………铸态和快淬态Mm(NiCoMnAl) 5合金的电化学　性能及相结构王国清等 (1- 19)…………………内禀矫顽力Hcj 对Nd Fe B磁体温度　稳定性的影响胡…     

Ni52Mn23+xSn25-x(x=0,1,2)合金的磁性

利用X射线衍射和振动样品磁强计研究了Ni52Mn23 xSn25-x(x=0,1,2)合金的结构和磁性.结果表明,合金为铁磁性形状记忆合金.奥氏体具有强的铁磁性,而马氏体表现为顺磁或反铁磁性.磁化曲线表现出明显的磁场诱导马氏体相变行为.Sn含量对居里温度影响十分显著,而对马氏体相变温度影响很小.合金马氏体相变过程的温度范围很窄,约在5K以内.     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

An Easy Way to Quantify the Adhesion Energy of Nanostructured Cu/X(X=Cr,Ta,Mo,Nb,Zr) Multilayer Films Adherent to Polyimide Substrates

An approach based on film buckling under simple uniaxial tensile testing was utilized in this paper to quantitatively estimate the interfacial energy of the nanostructured multilayer films(NMFs) adherent to flexible substrates. The interfacial energies of polyimide-supported NMFs are determined to be *5.0 J/m2 for Cu/Cr, *4.1 J/m2 for Cu/Ta,*2.8 J/m2 for Cu/Mo, *1.1 J/m2 for Cu/Nb, and *1.2 J/m2 for Cu/Zr NMFs. Furthermore, a linear relationship between the adhesion energy and the interfacial shear strength is clearly demonstrated for the Cu-based NMFs, which is highly indicative of the applicability and reliability of the modified models.     

High-Speed Friction Stir Welding of SiC_p/Al–Mg–Si–Cu Composite

A 17 vol% SiCp/Al–Mg–Si–Cu composite plate with a thickness of 3 mm was successfully friction stir welded(FSWed) at a very high welding speed of 2000 mm/min for the first time. Microstructural observation indicated that the coarsening of the precipitates was greatly inhibited in the heat-affected zone of the FSW joint at high welding speed, due to the significantly reduced peak temperature and duration at high temperature. Therefore, prominent enhancement of the hardness was achieved at the lowest hardness zone of the FSW joint at this high welding speed, which was similar to that of the nugget zone. Furthermore, the ultimate tensile strength of the joint was as high as 369 MPa, which was much higher than that obtained at low welding speed of 100 mm/min(298 MPa). This study provides an effective method to weld aluminum matrix composite with superior quality and high welding efficiency.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

A STUDY OF TEMPERATURE-DEPENDENT VALENCE BOND STRUCTURE OF TITANIUM

On the basis of energy and shape method for the determination of the valence bond (VB) structures of crystal, the valence bond structure of titanium is redetermined at room temperature and calculated in the whole temperature range of 0-1943K. The outer shell electronic distribution of Ti is e_c~(2.9907) · (s_c~(0.4980) d_c~(2.4927)) ef1.0093 in crystal. The temperature dependences of the VB structures of hcp and bcc phases are the same. The VB structures of hcp and bcc phases monotonically increase or decrease with the increase in temperature, but show discontinuous changes at the phase-transformation temperature 1155K.     

Structural Optimization of Electromagnetic Swirling Flow in Nozzle of Slab Continuous Casting

During the slab continuous casting process, the flow field of molten steel in the mold plays a decisive role in the quality of the slab. In this paper, electromagnetic swirling flow in nozzle technology is proposed to control the flow field in mold.This technology can drive molten steel to rotate inside the submerged entry nozzle by electromagnetic force, thereby controlling the flow field. This research shows that it can reduce the impact of molten steel on the bottom of nozzle and partly reduce the negative pressure at the upper part of nozzle outlet which is even eliminated by optimizing the structure and angle of nozzle. The area of heat flux of the mold wall becomes larger, and the crest value of heat flux gets lower than that without swirling in nozzle and any nozzle optimization. The meniscus fluctuates smoothly, and the flow velocity at the top surface is within a reasonable range. The temperature field distribution in the mold is uniform which was beneficial to the growth of equiaxed crystal and decreased element segregation.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).