聚合方法对硅胶表面接枝聚合物过程的影响研究

分别用溶液聚合与分散聚合两种方法,在硅胶载体表面实施了苯乙烯的接枝聚合,重点考察了聚合方法对接枝聚合过程的影响。结果表明,在基本相同的反应条件下,分散聚合体系的接枝率明显高于溶液聚合体系的接枝率,最高可达47%(即47g/100g);除聚合方法之外,影响聚合物在硅胶表面接枝率的因素还有硅胶表面的双键含量、单体浓度、引发剂浓度、温度等。     

Dynamic Mechanical Properties and Adhesive Joint Strengths of Emulsion Polymers Produced by Power Feed Technique. II. Chemical Structure of Grafted Power Feed Polymer

Power feed copolymers were synthesized using styrene and n-butyl acrylate through a non-uniform feeding emulsion polymerization. Poly(vinyl alcohol) (PVA) was used as a protective colloid, onto which vinyl monomers were grafted. With the increase of PVA, grafting was also increased. Feeding method did not affect grafting nor grafting efficiency to a great extent. However, the amount of initiator had a negative correlation against grafting or grafting efficiency. From NMR spectroscopy, it was known that n-butyl acrylate monomer grafted onto PVA rather than copolymerized with styrene monomer. In order to increase the cohesive strengths of each phase, grafting was introduced to the power feed polymerization. In these cases, the chemical structure of grafted power feed polymer was investigated.     

Dynamic Mechanical Properties and Adhesive Joint Strengths of Emulsion Polymers Produced by Power Feed Technique. II. Chemical Structure of Grafted Power Feed Polymer

Power feed copolymers were synthesized using styrene and n-butyl acrylate through a non-uniform feeding emulsion polymerization. Poly(vinyl alcohol) (PVA) was used as a protective colloid, onto which vinyl monomers were grafted. With the increase of PVA, grafting was also increased. Feeding method did not affect grafting nor grafting efficiency to a great extent. However, the amount of initiator had a negative correlation against grafting or grafting efficiency. From NMR spectroscopy, it was known that n-butyl acrylate monomer grafted onto PVA rather than copolymerized with styrene monomer. In order to increase the cohesive strengths of each phase, grafting was introduced to the power feed polymerization. In these cases, the chemical structure of grafted power feed polymer was investigated.     

Studies on preparation of PGMA/Al2O3 and its effect on impact strength of epoxy resin

In this article, two kinds of methods for grafting polyglycidyl methacrylate (PGMA) onto Al₂O₃ surface by the radical polymerization initiated by peroxide groups and double bond groups, respectively, were investigated. In the first method, peroxide groups, as initiators, were immobilized onto the Al₂O₃ surface. Then, GMA was polymerized on Al₂O₃ under the radicals decomposed by peroxide groups, and PGMA was grafted onto Al₂O₃. But in the second method, 3‐methacryloylpropyl trimethoxysilane was chemically bonded onto the Al₂O₃ surfaces firstly to introduce double bonds. Secondly, the copolymerizations between the immobilized double bonds and the monomer GMA were performed, homopolymerizations of GMA followed, and finally PGMA was grafted to the Al₂O₃ surfaces. The effects of grafting methods on grafting degree were examined mainly. At the same time, the effects of different grafting conditions on the grafting degree were researched. Furthermore, the effect of the grafted particles PGMA/Al₂O₃ on impact strength of the epoxy composites was studied. It was found that the grafting degree achieved by the first method was much higher than that by the second, and the grafting degree can reach about 54%. Moreover, the impact strength of epoxy composites containing PGMA/Al₂O₃ particles were improved largely, and which increased with the grafting degree. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Surface functionalization of Si3N4 nanoparticles by graft polymerization of glycidyl methacrylate and styrene

To improve dispersibility and interfacial interaction of nano‐Si₃N₄ particles in epoxy‐based composites, graft of glycidyl methacrylate (GMA) and styrene (St)/GMA onto the nanoparticles' surface was carried out in terms of emulsion polymerization method. The grafting polymers proved to be chemically attached to the nanoparticles via the double bonds introduced during the coupling agent pretreatment. The factors affecting the graft parameters, such as monomer concentration, initiator consumption, reaction time, etc., were investigated. It was shown that higher concentrations of monomer and initiator are favorable for the graft polymerization. When St/GMA was employed as the grafting monomer, the nanoparticles were found to play the role of polymerization loci. The grafted nanoparticles exhibit greatly improved dispersibility in cured epoxy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 992–999, 2006     

Mechanism and grafting reactions in seeded emulsion polymerization with emulsified monomer feeding

The seeded emulsion polymerization of styrene with emulsified monomer feeding was performed by polyethyl acrylate (PEA) latex as seed emulsion. It was shown that the grafting reactions occurred between two components on the composite latex particles. The loci of seeded polymerization were studied by the kinetics of grafting reaction. The highest grafting efficiency in the initial period of seeded emulsion polymerization supported the fact that the surfaces of PEA particles are the sites of polymerization of styrene. The grafting efficiency decreased with increasing monomer‐to‐polymer ratio and initiator concentration. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1495–1499, 1999     

Effect of solvents on radiation‐induced grafting of styrene onto fluorinated polymer films

The effect of solvents on radiation‐induced grafting of styrene onto commercial fluorinated polymer films such as poly(tetrafluoroethylene) (PTFE), poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) and poly(tetrafluoroethylene‐co‐perfluorovinyl ether) (PFA) was investigated by a simultaneous irradiation technique. Three solvents, ie methanol, benzene and dichloromethane, were used to dilute styrene under various irradiation doses, dose rates and monomer concentrations. The effect of addition of mineral and organic acids on the degree of grafting in the presence of the three solvents was also studied. The degree of grafting was found to be strongly dependent upon the type of solvent and composition of the monomer/solvent mixture. Dilution of styrene with dichloromethane in various grafting conditions was found to enhance dramatically the degree of grafting compared with other solvents, and the maximum degree of grafting was achieved at a monomer/solvent mixture having a composition of 60:40 (v/v). The formation of polystyrene grafts in the three fluorinated films was verified using FTIR spectrometry. © 2001 Society of Chemical Industry     

Graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto silica surface by Michael addition

The introduction of peroxycarbonate groups onto a silica surface and the graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto a silica surface were investigated. The introduction of peroxycarbonate groups onto a silica surface was achieved by Michael addition of amino groups introduced onto the silica surface to t‐butylperoxy‐2‐methacryloyloxyethylcarbonate (HEPO). The amount of peroxycarbonate groups was determined to be 0.17 mmol/g. The graft polymerization of various vinyl monomers such as styrene (St), N‐vinyl‐2‐pyrrolidinone (NVPD), and 2‐hydroxyethyl methacrylate (HEMA) was initiated by peroxycarbonate groups introduced onto the silica surface to give the corresponding polymer‐grafted silicas. The percentage of poly(St)‐grafting reached about 120% after 5 h. This means that 1.20 g of poly(St) is grafted onto 1.0 g of silica. The surface of poly(St)‐grafted silica shows a hydrophobic nature, but the surfaces of poly(NVPD) and poly(HEMA)‐grafted silica show a hydrophilic nature. Furthermore, the poly(St)‐grafted silica was found to give a stable colloidal dispersion in a good solvent for the grafted polymer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1491–1497, 1999     

Postgrafting of vinyl polymers onto hyperbranched poly(amidoamine)-grafted nano-sized silica surface

To prepare polymer-grafted nano-sized silica with hydrophilic core and hydrophobic shell and with higher percentage of grafting, the postgraft polymerization of vinyl polymers onto hyperbranched poly(amidoamine)-grafted (PAMAM-grafted) nano-sized silica initiated by the system consisting of Mo(CO)₆ and terminal trichloroacetyl groups of PAMAM-grafted silica was investigated. The introduction of trichloroacetyl groups onto PAMAM-grafted silica surfaces was readily achieved by the reaction of trichloroacetyl isocyanate with terminal amino groups of PAMAM-grafted silica. It was found that the polymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and glycidyl methacrylate (GMA) was successfully initiated by the system consisting of Mo(CO)₆ and terminal trichloroacetyl groups of PAMAM-grafted silica. In the polymerization, the corresponding vinyl polymers were effectively postgrafted onto PAMAM-grafted silica, based on the propagation of polymer from surface radicals formed by the reaction of terminal trichloroacetyl groups with Mo(CO)₆: the percentage of PMMA postgrafting onto PAMAM-grafted silica reached to 400% after 30 min, but the formation of gel was observed after 35 min. The formation of gel tends to decrease by use of hyperbranched PAMAM-grafted silica with higher percentage of grafting. The vinyl polymer-postgrafted nano-sized silica gave a stable colloidal dispersion in various organic solvents.     

Synthesis and characterization of PMMA grafted ZnO nanoparticles

ZnO nanoparticles were synthesized by homogeneous precipitation. To reduce the aggregation among ZnO nanoparticles, an effective surface modification method was proposed by grafting polymethyl methacrylate (PMMA) onto the ZnO particles. That is, the surface of ZnO nanoparticles was firstly treated with a KH570 silane coupling agent, which introduces functional double bonds onto the surface of ZnO nanoparticles, followed by radical grafting polymerization in non-aqueous medium. The obtained nanocomposite was characterized by Fourier transform infrared spectroscopy (FT-IR), thermogravimetry (TG), sedimentation test, scanning electron microscopy (SEM), and X-ray powder diffraction (XRD). Results of FT-IR and TG showed that the desired polymer chains have been covalently bonded to the surface of ZnO nanoparticles. It was found that the increasing monomer concentration could increase the grafting percentage and hence promote the dispersibility. The application of some surfactant is also helpful for dispersion. The viscous properties of nano-suspensions were investigated. The ZnO/PS nanocomposite was prepared by adding PMMA-grafted ZnO into styrene monomer, followed by radical grafting polymerization. The resulted nanocomposite was characterized by TG, DSC (differential scanning calorimetry) and XRD, and the testing results indicated that thermal behaviors of PS were obviously changed.     

Molecular characterization of alkyd/acrylic latexes prepared by miniemulsion polymerization

The molecular characterization of alkyd/acrylic hybrid latexes produced by miniemulsion polymerization was characterized in terms of the resin degree of grafting, acrylic degree of grafting, reacted double bonds in the alkyd, gel content, and molecular weight distribution of the sol part. A simple method based on conventional size exclusion chromatography measurements was developed to estimate the fraction of alkyd resin grafted to the acrylic polymer. The method could be applied to completely soluble hybrids and to hybrids containing gel. Also, the limits of the extraction method used in the literature to estimate the fraction of acrylic polymer grafted to the alkyd was investigated; we found that this technique only provided accurate results at high values of the acrylic degree of grafting. The combination of this information with the reacted double bonds of the alkyd (determined by iodine titration) and the molecular weight distribution of the sol polymer provided a detailed characterization of the alkyd–acrylic hybrid polymer. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

聚丁二烯橡胶接枝苯乙烯本体自由基聚合机理

采用傅里叶变换红外光谱法和碘值法分析了在热引发和化学引发方式下,低顺式和高顺式聚丁二烯橡胶接枝苯乙烯聚合物的双键结构和含量,确定了橡胶接枝苯乙烯本体自由基聚合机理。结果表明,热引发时,接枝机理主要是自由基夺取橡胶链上α氢原子;而化学引发时,同时存在自由基与橡胶双键加成的机理。橡胶的结构不同导致接枝点的位置差异,在低顺式聚丁二烯橡胶体系中,自由基以夺取反式-1,4-结构和1,2-乙烯基结构为主,而在高顺式聚丁二烯橡胶体系中。自由基以夺取顺式-1,4-结构为主。     

Radiation‐induced graft copolymerization of α‐methyl styrene and butyl acrylate mixture into polyetheretherketone films

Radiation‐induced graft copolymerization of α‐methyl styrene (AMS), butyl acrylate (BA) monomers, and their mixture was investigated on poly(etheretherketone) films. The graft polymerization was carried out using ethyl methyl ketone as the medium for the copolymerization and the maximum degree of grafting of 27% was achieved. It was observed that the grafting is significantly influenced by the reaction conditions, such as reaction time, preirrradiation dose, monomer concentration, monomer ratio, and the reaction temperature. The degree of grafting increases as the monomer concentration increases up to 30%, beyond which a decrease in the grafting was observed. The degree of grafting showed a maximum at 40% BA content in the monomer mixture. The temperature dependence of the grafting process shows decreasing grafting with the increase in the reaction temperature. The presence of AMS and BA grafts in the film was confirmed by FTIR spectra. The relative change in the PBA/PAMS fraction with respect to the reaction temperature has been found in this study. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Chemical Functionalization of Graphene Oxide by Poly(styrene sulfonate) Using Atom Transfer Radical and Free Radical Polymerization: A Comparative Study

Poly(sodium styrenesulfonate)-functionalized graphene was prepared from graphene oxide, using atom transfer radical polymerization and free radical polymerization. In atom transfer radical polymerization route, the amine-functionalized GO was synthesized through hydroxyl group reaction of GO with 3-amino propyltriethoxysilane. Atom transfer radical polymerization initiator was grafted onto modified GO (GO-NH₂) by reaction of 2-bromo-2-methylpropionyl bromide with amine groups, then styrene sulfonate monomers were polymerized on the surface of GO sheets by in situ atom transfer radical polymerization. In free radical polymerization route, the poly(sodium 4-styrenesulfonate) chains were grafted on GO sheets in presence of Azobis-Isobutyronitrile as an initiator and styrene sulfonate monomer in water medium. The resulting modified GO was characterized using range of techniques. Thermal gravimetric analysis, scanning electron microscopy, transmission electron microscopy, and atomic force microscopy results indicated the successful graft of polymer chains on GO sheets. Thermogravimetric analysis showed that the amount of grafted polymer was 22.5 and 31?wt% in the free radical polymerization and atom transfer radical polymerization methods, respectively. The thickness of polymer grafted on GO sheets was 2.1?nm (free radical polymerization method) and 6?nm (atom transfer radical polymerization method) that was measured by atomic force microscopy analysis. X-ray diffractometer and transmission electron microscopy indicated that after grafting of poly(sodium 4-styrenesulfonate), the modified GO sheets still retained isolated and exfoliated, and also the dispersibility was enhanced.     

Preparation and properties of poly[styrene‐co‐(butyl acrylate)‐co‐(acrylic acid)]/silica nanocomposite latex prepared using an acidic silica sol

BACKGROUND: Polyacrylate/silica nanocomposite latexes have been fabricated using blending methods with silica nanopowder, in situ polymerization with surface‐functionalized silica nanoparticles or sol–gel processes with silica precursors. But these approaches have the disadvantages of limited silica load, poor emulsion stability or poor film‐forming ability. RESULTS: In this work, poly[styrene‐co‐(butyl acrylate)‐co‐(acrylic acid)] [P(St‐BA‐AA)]/silica nanocomposite latexes and their dried films were prepared by adding an acidic silica sol to the emulsion polymerization stage. Morphological and rheological characterization shows that the silica nanoparticles are not encapsulated within polymer latex particles, but interact partially with polymer latex particles via hydrogen bonds between the silanol groups and the ? COOH groups at the surface of the polymer particles. The dried nanocomposite films have a better UV‐blocking ability than the pure polymer film, and retain their transparency even with a silica content up to 9.1 wt%. More interestingly, the hardness of the nanocomposite films increases markedly with increasing silica content, and the toughness of the films is not reduced at silica contents up to 33.3 wt%. An unexpected improvement of the solvent resistance of the nanocomposite films is also observed. CONCLUSION: Highly stable P(St‐BA‐AA)/silica nanocomposite latexes can be prepared with a wide range of silica content using an acidic silica sol. The dried nanocomposite films of these latexes exhibit simultaneous improvement of hardness and toughness even at high silica load, and enhanced solvent resistance, presumably resulting from hydrogen bond interactions between polymer chains and silica particles as well as silica aggregate/particle networks. Copyright © 2009 Society of Chemical Industry     

A facile,green, versatile protocol to prepare polypropylene‐g‐poly(methyl methacrylate) copolymer by water‐solid phase suspension grafting polymerization using the surface of reactor granule technology polypropylene granules as reaction loci

A facile and environment friendly process, called water‐solid phase suspension grafting polymerization, was developed to prepare polypropylene‐g‐poly(methyl methacrylate) (PP‐g‐PMMA) copolymer with a submicrometer microdomain. In this approach, graft polymerization was elaborately regulated to occur within micropores of polypropylene particles prepared by reactor granule technology. FTIR spectra of the samples after extraction demonstrated that PMMA was successfully grafted onto the PP. The results showed grafting percentage (GP) of PMMA increased with the increasing monomer ratios to PP and that could reach 13.6%. Whereas the grafting efficiency decreased as the monomer ratio increased. The addition of second monomer styrene improved GP up to 24.5%. Differential Scanning Calorimetry tests showed that the grafting of PMMA have a slight effect on the melting point and the relative crystallinity of PP. TEM micrographs demonstrated PMMA domains distributed in PP matrix with sizes ranging from about 100 to 300 nm. In addition, Shear viscosity increased with the growing GP indicated by rheological measurement. The preliminary evaluation showed PP‐g‐PMMA was effective in improving the compatibility of PP/acrylonitrile‐styrene‐acrylate blends. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

悬浮法PEB-g-SAN的合成及其对SAN树脂的增韧作用

以(乙烯/1丁-烯)共聚物(PEB)、苯乙烯(St)和丙烯腈(AN)为原料,采用悬浮接枝共聚法合成了(苯乙烯/丙烯腈)共聚物(SAN)接枝PEB(PEB-g-SAN),用其与SAN熔融共混制备了冲击性能优异的增韧塑料AEBS。研究了反应条件对单体转化率(CR)、接枝率(GR)、接枝效率(GE)及AEBS冲击性能的影响。结果表明,在适宜的聚合条件下,PEB/St-SAN悬浮接枝体系具有较高的CR、GE和GR,分别可达94.8%、49.3%和38.2%。当PEB质量分数为25%时,AEBS的缺口冲击强度高达42.8 kJ/m2,约为纯SAN(1.2 kJ/m2)的35倍。扫描电子显微镜分析表明,增韧机理以剪切屈服为主。动态机械分析表明,在PEB-g-SAN接枝反应中,当PEB质量分数为55%、AN为35%时,其增韧的AEBS的两个tanδ峰向内靠拢程度最大,SAN与PEB-g-SAN的相容性最好。     

Cationic graft polymerization of polymers from carbon fiber initiated by acylium perchlorate groups introduced onto the surface

The cationic graft polymerization of several monomers initiated by acylium perchlorate groups introduced onto the carbon fiber surface was investigated to modify the surface. The introduction of acylium perchlorate groups was successfully achieved by the reaction of silver perchlorate with acyl chloride groups, which were introduced by the reaction of surface carboxyl groups with thionyl chloride. It was found that the cationic polymerization of styrene is initiated by acylium perchlorate groups on the carbon fiber. In the polymerization, polystyrene was grafted onto the carbon fiber surface through the propagation of polystyrene from the surface. Ungrafted polymer was also formed by the chain transfer reaction of growing polymer cation to the monomer. The acylium perchlorate groups have the ability to initiate cationic ring-opening polymerization of tetrahydrofuran (THF) and ε-caprolactone (CL), polyTHF and polyCL being grafted onto the carbon fiber surface, respectively. Polyacetals, such as poly(1,3-dioxolane) and polyoxymethylene, were able to graft onto the carbon fiber by cationic ring-opening polymerization of the corresponding monomers.     

Preparation of Ni-g-polymer core–shell nanoparticles by surface-initiated atom transfer radical polymerization

Surface-initiated atom transfer radical polymerization (si-ATRP) technique was successfully employed to modify Ni nanoparticles with polymer shells. ATRP initiators were covalently bonded onto Ni nanoparticle surfaces by a combination of ligand exchange and condensation reactions. Various kinds of polymers including poly(methyl methacrylate) (PMMA) and poly(n-isopropylacrylamide) (PNIPAM) were grafted from the immobilized initiators. The grated polymer shells gave Ni nanoparticles exceptionally good dispersion and stability in solvents. Fourier transform infrared (FT-IR) spectroscopy, thermogravimetric analysis (TGA) and transmission electron spectroscopy (TEM) were employed to confirm the grafting and to characterize the nanoparticle core–shell structure. Gel permeation chromatography (GPC) studies of cleaved polymer chains revealed that the grafting polymerization was well controlled. The magnetic properties of Ni-g-polymer nanoparticles were also studied.     

Preparation of acrylate polymer/silica nanocomposite particles with high silica encapsulation efficiency via miniemulsion polymerization

Acrylate polymer/silica nanocomposite particles were prepared through miniemulsion polymerization by using methyl methacrylate/butyl acrylate mixture containing the well-dispersed nano-sized silica particles coupling treated with 3-(trimethoxysilyl)propyl methacrylate (MPS). The encapsulation efficiency of silica particles was determined through the elution and hydrofluoride acid etching experiments, and the size distribution and the morphology of the composite latex particles were characterized by dynamic light scattering and transmission electron microscopy. The coupling treatment of silica with MPS can improve the encapsulation efficiency of silica and the degree of grafting of polymer onto silica. When 0.10 g MPS/g silica was used to modify silica, the encapsulation efficiency of silica was greater than 95%, and the degree of grafting of acrylate polymer onto silica was about 60%. Although the average size and the size distribution index of the composite latex particles increased as the weight fraction of silica increased, the stable latex containing the ‘guava-like’ composite particles was obtained. The grafting of polymer onto silica particles improved the dispersion of silica particles in the solvents for acrylate polymer and in the polymer matrix.