Gold Stud Bumps Flip-Chip Bonded onto Copper Electrodes with Titanium and Silver Layers

The purpose of this study was to develop the thermosonic flip-chip bonding process for gold stud bumps bonded onto copper electrodes on an alumina substrate. Copper electrodes were deposited with silver as the bonding layer and with titanium as the diffusion barrier layer. Deposition of these layers on copper electrodes improves the bonding quality between the gold stud bumps and copper electrodes. With appropriate bonding parameters, 100% bondability was achieved. Bonding strength between the gold stud bumps and copper electrodes was much higher than the value converted from the standards of the Joint Electron Device Engineering Council (JEDEC). The effects of process parameters, including bonding force, ultrasonic power, and bonding time, on bonding strength were also investigated. Experimental results indicate that bonding strength increased as bonding force and ultrasonic power increased and did not deteriorate after prolonged storage at elevated temperatures. Thus, the reliability of the high-temperature storage (HTS) test for gold stud bumps flip-chip bonded onto a silver bonding layer and titanium diffusion barrier layer is not a concern. Deposition of these two layers on copper electrodes is an effective and direct method for thermosonic flip-chip bonding of gold stud bumps to a substrate, and ensures excellent bond quality. Applications such as flip-chip bonding of chips with low pin counts or light-emitting diode (LED) packaging are appropriate.     

Thermosonic bonding of gold wire onto silver bonding layer on the bond pads of chips with copper interconnects

A copper pad oxidizes easily at elevated temperatures during thermosonic wire bonding for chips with copper interconnects. The bondability and bonding strength of a gold wire onto a bare copper pad are seriously degraded by the formation of a copper oxide film. A new bonding approach is proposed to overcome this intrinsic drawback of the copper pad. A silver layer is deposited as a bonding layer on the surface of copper pads. Both the ball-shear force and the wire-pull force of a gold wire bonded onto copper pads with silver bonding layers far exceed the minimum values stated in the JEDEC standard and MIL specifications. The silver bonding layer improves bonding between the gold ball and copper pads. The reliability of gold ball bonds on a bond pad is verified in a high-temperature storage (HTS) test. The bonding strength increases with the storage time and far exceeds that required by the relevant industrial codes. The superior bondability and high strength after the HTS test were interpreted with reference to the results of electron probe x-ray microanalyzer (EPMA) analysis. This use of a silver bonding layer may make the fabrication of copper chips simpler than by other protective schemes.     

Thermosonic bonding of gold wire onto a copper pad with titanium thin-film deposition

A novel thermosonic (TS) bonding process for gold wire bonded onto chips with copper interconnects was successfully developed by depositing a thin, titanium passivation layer on a copper pad. The copper pad oxidizes easily at elevated temperature during TS wire bonding. The bondability and bonding strength of the Au ball onto copper pads are significantly deteriorated if a copper-oxide film exists. To overcome this intrinsic drawback of the copper pad, a titanium thin film was deposited onto the copper pad to improve the bondability and bonding strength. The thickness of the titanium passivation layer is crucial to bondability and bonding strength. An appropriate, titanium film thickness of 3.7 nm is proposed in this work. One hundred percent bondability and high bonding strength was achieved. A thicker titanium film results in poor bond-ability and lower bonding strength, because the thicker titanium film cannot be removed by an appropriate range of ultrasonic power during TS bonding. The protective mechanism of the titanium passivation layer was interpreted by the results of field-emission Auger electron spectroscopy (FEAES) and electron spectroscopy for chemical analysis (ESCA). Titanium dioxide (TiO₂), formed during the die-saw and die-mount processes, plays an important role in preventing the copper pad from oxidizing. Reliability of the high-temperature storage (HTS) test for a gold ball bonded on the copper pad with a 3.7-nm titanium passivation layer was verified. The bonding strength did not degrade after prolonged storage at elevated temperature. This novel process could be applied to chips with copper interconnect packaging in the TS wire-bonding process.     

Enhancement of the Bondability and Die-Shear Force of Chip–Flex Substrate Assemblies by Depositing a Nickel Layer on the Flex Substrate

A nickel layer and a silver bonding layer have been deposited on copper electrodes over flex substrates to improve the bondability and die-shear force performance of chip?Cflex substrate assemblies when using the thermosonic flip-chip bonding process. For bonding temperature of 200°C, the maximum die-shear force was achieved by combining parameter values of 20.66?W ultrasonic power, 625?gf bonding force, and 0.5?s bonding time. The improved bondability and die-shear force could be attributed to better transfer of ultrasonic power across the bonding interface during thermosonic flip-chip bonding, owing to the high rigidity of the copper electrodes provided by the nickel layer. Experimental results also indicated that high bonding load is necessary at elevated ultrasonic power range to provide firm contact between the bumps and electrodes to enable smooth ultrasonic power transfer across the bonding interface. Moreover, prolonged bonding time caused cracks between the bumps and flex substrate. Close examination of the fracture morphologies after die-shear testing and after ultrasonic separation provided insight into the die-shear force performance as influenced by the process parameters and by the deposition of the nickel layer on the copper electrodes over the flex substrate.     

Increasing bondability and ball-shear force of gold balls thermosonic bonding to flex substrates by depositing a nickel layer

To improve the bondability and ball-shear force of gold balls that are thermosonically bonded to copper electrodes over flex substrates, a nickel layer was deposited on the surface of the copper electrodes to increase their rigidity. A silver layer was then deposited on the nickel layer to prevent oxidation of the copper electrodes during the thermosonic bonding process. This nickel layer was expected to enhance the rigidity of copper electrodes over the flex substrates, increasing the thermosonic bonding efficiency of gold balls to copper electrodes over the flex substrates.Deposition the nickel layer on the copper electrodes improved the elastic modulus of the flex substrates, indicating that the nickel layer is effective in enhancing the rigidity of copper electrodes over the flex substrates. The bondability and ball-shear force of gold balls that are thermosonically bonded to copper electrodes increases with the thickness of the nickel layer given fixed bonding parameters. One hundred percent bondability and high ball-shear force can be achieved when gold balls are thermosonically bonded to copper electrodes with the deposition of a 0.5 μm-thick nickel layer. Herein, the ball-shear force was higher than that specified in JEDEC standards. Furthermore, gold balls that were thermosonically bonded to copper electrodes with a nickel layer had a large bonded area with an extensive scrape, while gold balls that were thermosonically bonded to copper electrodes without a nickel layer had a blank surface morphology. This experimental result was similar to that of tests of the elastic modulus of flex substrates, similarity can be used to explain that the effectiveness of the nickel layer in increasing the rigidity of copper electrodes, increasing the bonding efficiency at the bonding interface between gold balls and copper electrodes during thermosonic bonding process. After ball-shear test, a layer that was stuck on the ball bond was observed at the location of fracture of the ball bonds for gold balls they were thermosonically boned on copper electrodes with 0.5 μm-thick nickel layer. This observation implies that the ball-shear force of the gold balls that were bonded on the copper electrodes exceeded even the adhesive force of the layers that were deposited on the copper electrodes.The deposition of a 0.5 μm-thick nickel layer on copper electrodes over flex substrates improved the rigidity of the copper electrodes; the ultrasonic power could be propagated to the bonding interface between the gold balls and the copper electrodes, increasing the bondability and ball-shear force.     

Single chip bumping and reliability for flip chip processes

Processes of bump deposition based on mechanical procedures together with their reliability data are summarized in this paper. The stud bumping of gold, palladium, and solder is described and also a novel bumping approach for fine pitch solder deposition down to 100 μm pitches using thermosonic bonding on a modified wedge–wedge bonding machine. This wedge bumping doesn’t require a wire flame-off process step. Because of this, no active atmosphere is necessary. The minimum pad diameter which can be bumped using the solder wedge bumping is 50 μm, up to now. This bumping process is highly reproducible and therefore well-suited for different flip chip soldering applications. Palladium stud bumps provide a solderable under bump metallization. Results from aging of lead/tin solder bumps on palladium are shown. The growth of intermetallics and its impact on the mechanical reliability are investigated.     

Increasing the bonding strength of chips on flex substrates using thermosonic flip-chip bonding process with nonconductive paste

Thermosonic flip-chip bonding process with a nonconductive paste (NCP) was employed to improve the processability and bonding strength of the flip-chip onto flex substrates (FCOF). A non-conductive paste was deposited on the surface of the copper electrodes over the flex substrate, and a chip with eight gold bumps bonded onto the copper electrodes by the thermosonic flip-chip bonding process.For the chips and flex substrates assembly, ultrasonic power is important in the removal of some of the non-conductive paste on the surface of copper electrodes during thermosonic bonding. Accordingly, gold stud bumps in this study were directly bonded onto copper electrodes to form successful electrical paths between chips and the flex substrate. A particular ultrasonic power resulted in some metallurgical bonding between the gold bumps and the copper electrodes, increasing the bonding strength. The ultrasonic power was not only to remove the NCP from the copper electrodes, but also formed metallurgical bonds during the thermosonic flip-chip bonding process with NCP.In this study, the parameters of the bonding of chips onto flex substrates using thermosonic flip-chip bonding process with NCP were a bonding force of 4.9 N, a curing time of 40 s, a curing temperature of 140 °C and an ultrasonic power of 14.46 W. The processability and bonding strength of flip-chips on flex substrates using thermosonic bonding process with NCP was verified in this study. This process has great potential to be applied to the packaging of consumed electronic products.     

Investigation of Thermosonic Wire Bonding Resistance of Gold Wire Onto Copper Pad

This paper discusses the electric performance for thermosonic wire bonding of gold wire onto copper pads. Various methods normally used to improve bondability were investigated including the bare copper pads with argon shielding gas and the copper pads with cupric oxide film, cuprous oxide film, and silver film. The micro-contact theory was used to determine the effective contact area. The circuit contact resistance was measured for each sample and was presented in terms of ultrasound power and effective contact area. The results show that the increase in the effective contact area leads to a lower circuit contact resistance before reaching a minimum value, and further increase in the effective contact area would not have noticeable effect on the resistance.      

Reliability of assembly of chips and flex substrates using thermosonic flip-chip bonding process with a non-conductive paste

This study investigates the reliability of the assembly of chips and flex substrates using the thermosonic flip-chip bonding process with non-conductive paste (NCP). The high-temperature storage (HTS) test, the temperature cycling test (TCT), the pressure cooker test (PCT) and the high-temperature/high-humidity (HT/HH) test were conducted to examine the reliability of chips that are bonded on flex substrates. The environmental parameters used in the various reliability tests were consistent with the JEDEC standards. After the reliability tests, a peeling test was performed and the microstructure of the tested specimen observed to evaluate further the reliability.The bonding strength increased with the storage period in the HTS test. After the peeling test, a layer of copper electrodes was observed to be stuck on gold bumps over the fractured morphology of the chips when the chips and flex substrates were assembled using an ultrasonic power of 14.46 W, indicating that the bonding strength between the gold bumps and the copper electrodes was even higher than the adhesive strength of the layers that were deposited on the flex substrates. The HTS test yielded sufficient thermal energy to promote atomic interdiffusion between gold bumps and copper electrodes. Metallurgical bonding between the gold bump and the copper electrode occurred, improving the bonding strength. In the assembly of chips and flex substrates without the application of ultrasonic power in bonding process, the adhesive strength of NCP was highly reliable after HTS test, because the bonding strength was maintained after HTS test for various storage periods. The typical failure mode of PCT was interfacial delamination between NCP and flex substrates. Approximately 80% of the specimens exhibited full separation after PCT at 336 h when chips and flex substrates were assembled without applied ultrasonic power to the bonding process, revealing that the NCP cannot withstand the PCT and lost its adhesive strength. Applying an adequate ultrasonic power of 14.46 W in the bonding process not only improved the bonding strength, but also enabled the bonding strength to be maintained at high level after PCT. The high bonding strength was attributable to the strong bonding of the gold bumps on the copper electrodes after PCT for various storage periods. This experimental result demonstrates that ultrasonic power can increase the reliability of PCT on chips and flex substrates that were assembled with the NCP. The bonding strength of the gold bumps on the flex substrates did not change significantly after the TCT, revealing the great reliability of TCT on chips and flex substrates that were assembled using the thermosonic flip-chip bonding process with the NCP. The bonding strength of chips bonded to flex substrates increased with the storage periods of the HT/HH test if ultrasonic power was applied to bonding process. Neither delamination nor any defect at the bonding interface was observed. The reliability of the HT/HH test for chips bonded on flex substrates using the thermosonic flip-chip process with the NCP fulfills the requirements stated in the JEDEC standards.According to the experimental findings of various reliability tests, the chips that were bonded to flex substrates using the thermosonic bonding process with NCP met the JEDEC specifications; with the exception of the adhesive strength of NCP under PCT which must be improved.     

A Novel Three-Dimensional Packaging Method for Al-Metalized SiC Power Devices

A novel three-dimensional packaging method for Al-metalized SiC power devices has been developed by means of Au stud bumping technology and a subsequent vacuum reflow soldering process with Au-20Sn solder paste. Al-metalized electrodes of a SiC power chip can be robustly assembled to a direct bonded copper (DBC) substrate with this method. The bump shear strength of a Au stud bump on an Al electrode of a SiC chip increased with bonding temperature. The die shear strength of a SiC chip on the DBC substrate increased with the number of Au stud bumps which were preformed on the Al electrode. The bonded SiC-SBD chips on a DBC substrate were aged at 250 ${^circ}{rm C}$ in a vacuum furnace and the morphologies, die shear strength and electrical properties were investigated after a certain aging time. After 1000 h aging at 250 ${^circ}{rm C}$, the electrical resistance of the bonded SiC-SBD chips only increased about 0.4%, the residual die shear strength was much higher than that of the IEC749 (or JEITA) standard value, and little morphological change was observed by a micro-focus X-ray TV system. Very little diffusion between Au stud bumps and Au-20Sn solder was observed by scanning electron microscope (SEM) equipped with an energy dispersed X-ray analyzer (EDX). Intermetallic compounds (IMC) evolved at the interface of chip/solder and chip/Au stud bumps after 1000 h aging at 250 ${^circ}{rm C}$. With this method, power devices with Al bond pads can be three-dimensionally packaged.      

Oxidation of copper pads and its influence on the quality of Au/Cu bonds during thermosonic wire bonding process

To understand the copper oxide effect on the bondability of gold wire onto a copper pad, thermosonic gold wire bonding to a copper pad was conducted at 90–200 °C under an air atmosphere. The bondability and bonding strength of the Au/Cu bonds were investigated. The bondability and bonding strength were far below the minimum requirements stated in industrial codes. At elevated bonding temperature of 200 °C, the bondability and bonding strength deteriorated mainly due to hydroxide and copper oxide formation on the copper pad. Oxide formation occurred if no appropriate oxide preventive schemes were applied. At lower bonding temperature, 90 °C, poor bondability and low bonding strength were mainly attributed to insufficient thermal energy for atomic inter-diffusion between the gold ball and copper pad.Copper pad oxidation was investigated using an electron spectroscopy for chemical analysis (ESCA) and thermogravimetric analysis (TGA). An activation energy of 35 kJ/mol for copper pad oxidation was obtained from TGA. This implies that different mechanisms govern the oxidation of copper pad and bulk copper. Hydroxide and copper oxide were identified based on the shifted binding energy. Cu(OH)₂ forms mainly on the top surface of copper pads and the underlying layer consists mainly of CuO. The hydroxide concentration increased with increasing the heating temperatures. After heating at 200 °C, the hydroxide concentration on the copper pad surface was approximately six times that at 90 °C. Protective measures such as passivation layer deposition or using shielding gas are critical for thermosonic wire bonding on chips with copper interconnects.     

Flip chip interconnect systems using copper wire stud bump and leadfree solder

This research focuses on flip chip interconnect systems consisting of wire stud bumps and solder alloy interconnects. Conventional gold (Au) wire stud bumps and new copper (Cu) wire stud bumps were formed on the chip by wire stud bumping. Cu wire studs were bumped by controlling the ramp rate of ultrasonic power to eliminate the occurrence of under-pad chip cracks that tend to occur with high strength bonding wire. Lead free 96Sn3.5Ag0.5Cu (SnAgCu) alloy was used to interconnect the wire studs and printed circuit board. A comparison was made with conventional eutectic 63Sn37Pb (SnPb) alloy and 60In40Pb (InPb) alloy. Test vehicles were assembled with two different direct chip attachment (DCA) processes. When the basic reflow assembly using a conventional pick and place machine and convection reflow was used, 30% of the lead free test vehicles exhibited process defects. Other lead free test vehicles failed quickly in thermal shock testing. Applying the basic reflow assembly process is detrimental for the SnAgCu test vehicles. On the other hand, when compression bonding assembly was performed using a high accuracy flip chip bonder, the lead free test vehicles exhibited no process defects and the thermal shock reliability improved. Cu stud-SnAgCu test vehicles (Cu-SnAgCu) in particular showed longer mean time to failure, 2269 cycles for the B stage process and 3237 cycles for high temperature bonding. The C-SAM and cross section analysis of the Cu stud bump assemblies indicated less delamination in thermal shock testing and significantly less Cu diffusion into the solder compared to Au stud bumped test vehicles. The Cu stud-SnAgCu systems form stable interconnects when assembled using a compression bonding process. Moreover, Cu wire stud bumping offers an acceptable solution for lead free assembly     

Thermosonic flip-chip bonding for SAW filter

A flip-chip bonding (FCB) method suitable for the surface acoustic wave (SAW) filter was developed. In this method, the gold-ball bumps formed on the chip are directly bonded onto the ceramic substrate by thermosonic bonding. After FCB, they are sealed with a cap without using underfill resin. To obtain high bond strength, characteristic properties of the substrate electrode and the ball bump, were optimized. Furthermore, bondability has been improved by adopting a ramp-up loading profile. The reliability test was carried out with 6-pin SAW chips, and we confirmed the sufficient reliability of bonds.     

Electroplated indium bump arrays and the bonding reliability

A novel electroplating indium bumping process is described,as a result of which indium bump arrays with a pitch of 100μm and a diameter of 40μm were successfully prepared.UBM(under bump metallization) for indium bumping was investigated with an XRD technique.The experimental results indicate that Ti/Pt(300(?)/200(?)) has an excellent barrier effect both at room temperature and at 200℃.The bonding reliability of the indium bumps was evaluated by a shear test.Results show that the shear strength of the ind...     

Innovative wire bonding method using a chemically reacted thin layer for chips with copper interconnects

This paper presents a novel method in which an oxide film is used to facilitate the thermosonic wire bonding of gold wire onto copper pads. A cuprous oxide film is generated by controlling the pH values of the chemical solution. Compared to cupric oxide films, the cuprous oxide film is denser and more brittle and therefore facilitates the bonding process without the need for the elaborate procedures and equipment required by more conventional wire bonding methods.     

Electroless Ni/Au Bump on a Copper Patterned Wafer for the CMOS Image Sensor Package in Mobile Phones

Wafer bumping technology using an electroless Ni/Au bump on a Cu patterned wafer is studied for the flip chip type CMOS image sensor (CIS) package for the camera module in mobile phones. The effect of different pretreatment steps on surface roughness and etching of Cu pads is investigated to improve the adherence between the Cu pad and the Ni/Au bump. This study measures the shear forces on Ni/Au bumps prepared in different ways, showing that the suitable pretreatment protocol for electroless Ni plating on Cu pads is “acid dip followed by Pd activation” rather than the conventional progression of “acid-dip, microetching, and Pd activation.” The interface between the Cu pad and the Ni/Au bump is studied using various surface analysis methods. The homogeneous distribution of catalytic Pd on the Cu pad is first validated. The flip chip package structure is designed, assembled, and tested for reliability. The successful flip chip bonding in the CIS package is characterized in terms of the cross-sectional structure in which the anisotropic conductive film (ACF) particles are deformed to about 1.5 μm in diameter. The experimental results suggest that electroless Ni/Au can be applied to the flip chip type CIS package using Cu patterned wafers for high mega pixel applications.     

Effects of metallization characteristics on gold wire bondability of organic printed circuit boards

Organic printed circuit boards (PCBs) with Au/Ni plates on bond pads are widely used in chip-on-board (COB), ball grid array (BGA), and chip-scale packages. These packages are interconnected using thermosonic gold wire bonding. The wire bond yield relies on the bondability of the Ni/Au pads. Several metallization parameters, including elemental composition, thickness, hardness, roughness, and surface contamination, affect the success of the solid state joining process. In this study, various characterization and mechanical testing techniques are employed to evaluate these parameters for different metallization schemes with varying Ni and Au layer thicknesses. The pull force of Au wires is measured as a function of plasma treatment applied before wire bonding to clean the bond pads. Close correlations are established between metallization characteristics and wire bond quality.     

Bondability analysis of bond pads by thermoelectric temperature measurements

To reduce cost and enhance reliability for microelectronics applications, a complete understanding of the thermosonic bonding process is required. In particular, the question of whether melting, diffusion, or significant heating occurs along the interface during friction has often been raised. We present results obtained with a new device based on thermoelectric temperature measurements to determine the temperature at the bond interface. In addition to the temperature information, the data characterizes the bonding process in real time on a micrometer scale. The basic principle of the developed apparatus is temperature measurement by an Au-Ni thermocouple fixed within the inside chamfer of a bonding capillary. Different bond substrates with high and low bond contact quality have been investigated. The thermoelectric temperature measurements very precisely determines the bonding behavior of the bond pads. A few nanometers surface contamination on a bond pad significantly reduces the temperature rise at the bond interface and therefore impairs bondability of the substrate. These results demonstrate the sensitivity and accuracy of the measurement principle. The apparatus is a powerful tool to measure the tribology of the bond system and to characterize the bondability of different bond pads.     

热超声倒装焊在制作大功率GaN基LED中的应用

设计了适合于倒装的大功率GaN基LED芯片结构,在倒装基板硅片上制作了金凸点,采用热超声倒装焊接(FCB)技术将芯片倒装在基板上.测试结果表明获得的大面积金凸点连接的剪切力最高达53.93 g/bump,焊接后的GaN基绿光LED在350 mA工作电流下正向电压为3.0 V.将热超声倒装焊接技术用于制作大功率GaN基LED器件,能起到良好的机械互连和电气互连.     

Carbon nanotubes for nanoscale low temperature flip chip connections

In this work we demonstrate a new approach for ultra fine flip chip interconnections based on carbon nanotubes as a wiring material. In contrast to other works we show patterned growth of multi walled CNTs on substrates with pre-structured bond pads including a complete metallization system for electrical characterization. Furthermore, we succeeded achieving a reliable flip chip connection between CNT-covered contact pads and metal pads at temperatures lower than 200 °C. Our goal is a reversible electrical and mechanical chip assembly with CNT bumps.For bonding experiments and electrical characterization a test structure with a damascene metallization including a layer stack of TiN/Cu/TiN was prepared. For CNT growth a thin nickel catalyst layer was selectively deposited with sputtering and a lift-off technique on the contact pads. The CNTs were grown by thermal CVD with ethylene as carbon source. CNT growth parameters like catalyst thickness, gas composition, growth time and temperature were optimized to get dense CNT growth. The metal bumps of the counter chip consist of electroless deposited Ni. With the selected layout we can obtain daisy chain and four-point measurements for lossless determination of single contact resistance. We have obtained reliable electrical contacts with relatively small resistance reaching values as low as 2.2 Ω. As CNT-quality is strongly dependent on the growth temperature we observed a strong change in resistivity of the flip chip connection as the growth temperature was varied. Reliability tests showed long time stability under thermal stress proving a reliable electrical contact between the contact pads. There is an appropriate potential for further optimization of the CNT bump resistance and applying this technology for IC-devices.