High-throughput optimization and fabrication of Bi2Te2.7Se0.3-based artificially tilted multilayer thermoelectric devices

Artificially tilted multilayer thermoelectric devices (ATMTDs) have attracted growing attention due to their ease in miniaturization and high flexibility in device design. However, most of these devices are inefficient due to the lack of effective strategy to optimize their material matching and geometrical configurations. Herein, a high-throughput optimization approach is employed to screen high-performance Bi₂Te_2.7Se_0.3-based ATMTDs from a material genome database covering 230 kinds of candidates. 14 kinds of ATMTDs are found to have ZT_zx,max values exceeding 0.3 and tilt angles greater than 15°. Bi_0.1Sb_1.9Te₃/Bi₂Te_2.7Se_0.3 ATMTD is screened out and fabricated because of its excellent transverse figure of merit, large tilt angle, and good interface compatibility. Consequently, transverse figure of merit over 0.3, thermal sensitivity greater than 0.11 mV·K^?1, and power density up to 1.1 kW·m^?2 are recorded in Bi_0.1Sb_1.9Te₃/Bi₂Te_2.7Se_0.3 ATMTD. This indicates that ATMTDs have great potential for application in the fields of temperature detection and power generation.     

Preparation and thermoelectric properties of Bi2SexTe3−x bulk materials

Bi₂Te₃ and Bi₂Se₃ nanoplates were synthesized by a microwave-assisted wet chemical method, and Bi₂Se_xTe_3−x (x=1, 2, 3) bulk nanocomposites were then prepared by hot pressing the Bi₂Te₃ and Bi₂Se₃ nanoplates at 80 MPa and 723 K in vacuum. The phase composition and microstructures of the bulk samples were characterized by powder X-ray diffraction and field-emission scanning electron microscopy, respectively. The electrical conductivity of the Bi₂Se_xTe_3−x bulk nanocomposites increases with increasing Se content, and the Seebeck coefficient value is negative, showing n-type conduction. The absolute Seebeck coefficient value decreases with increasing Se content. A highest power factor, 24.5 µWcm⁻¹ K⁻², is achieved from the sample of x=1 at 369 K among the studied samples.     

Ti3C2Tx aerogel with 1D unidirectional channels for high mass loading supercapacitor electrodes

As one of the typical MXenes materials, 2D Ti₃C₂T_x has attracted extensive attention in the field of energy storage. However, due to the restacking problem of Ti₃C₂T_x nanosheets, the electrochemical performance of Ti₃C₂T_x is unsatisfactory. In this paper, a scheme is proposed to obtain 3D aerogel with 1D channels by directional freeze drying of Ti₃C₂T_x. With the help of the unidirectional channels, the 3D Ti₃C₂T_x/Sodium alginate (SA) aerogel can effectively solve the stacking problem of Ti₃C₂T_x nanosheets, and it also accelerates the diffusion of ions. The Ti₃C₂T_x/SA-5 electrode can still reach the mass capacitance of 284.5 F g^?1 and the areal capacitance of 4030.4 mF cm^?2 at 2 mV s^?1 when the loading is 14.2 mg cm^?2 in 1 M H₂SO₄ electrolyte. In addition, the electrode showed good cycling performance without capacitor degradation after 20,000 cycles at 50 mV s^?1. These results suggest that by using the strategy of building special 3D structure of 2D MXene with 1D unidirectional channels, high performance supercapacitor electrodes with high mass loading can be realized.     

Fabrication of PANI@Ti3C2Tx/PVA hydrogel composite as flexible supercapacitor electrode with good electrochemical performance

Developing a new strategy to effectively prevent the restacking of MXene nanosheets will have significant impacts on designing flexible supercapacitor electrodes. Herein, a novel Ti₃C₂T_x/polyvinyl alcohol (PVA) porous sponge with 3D interconnected structures is prepared by sol-gel and freeze-dried methods. This Ti₃C₂T_x/PVA porous sponge is used as the template of in-situ polyaniline (PANI) polymerization, and the fabricated PANI@Ti₃C₂T_x/PVA hydrogel composite is applied as flexible supercapacitors electrodes. 1D conductive polymer chains PVA could increase the interlayer spacing of Ti₃C₂T_x nanosheets, which is beneficial to expose more electrochemical active sites. The supercapacitor based on PANI@Ti₃C₂T_x/PVA hydrogel composite exhibits the coexistence of double-layer capacitance and pseudocapacitance behavior. This supercapacitor shows a maximum areal specific capacitance of 103.8 mF cm^?2 at 2 A m^?2, and it also exhibits a maximum energy density of 9.2 μWh·cm^?2 and an optimum power density of 800 μW cm^?2. The capacitance of this supercapacitor is almost not change under different bending angles. Moreover, 99% capacitance retention is achieved after 10 000 charge/discharge cycles of the supercapacitor. The synergistic effect between PANI and Ti₃C₂T_x/PVA composite may improve the number of reactive sites and provide efficient channels for ion diffusion/electron transport.     

Fabrication and electrical properties of Bi2-xSbxTe3 ternary nanopillars array films

Highly oriented Bi_2-xSb_xTe₃ (x?=?0, 0.7, 1.1, 1.5, 2) ternary nanocrystalline films were fabricated using vacuum thermal evaporation method. Microstructures and morphologies indicate that Bi_2-xSb_xTe₃ films have pure rhombohedral phase with well-ordered nanopillars array. Bi, Sb and Te atoms uniformly distributed throughtout films with no precipitation. Electrical conductivity of Bi_2-xSb_xTe₃ films transforms from n-type to p-type when x?>?1.1. Metal-insulator transition was observed due to the incorporation of Sb in Bi₂Te₃. Bi_2-xSb_xTe₃ film with x?=?1.5 exhibits optimized electrical properties with maximum electrical conductivity σ of 2.95?×?10⁵ S?m^?1 at T?=?300?K, which is approximately ten times higher than that of the undoped Bi₂Te₃ film, and three times higher than previous report for Bi_0.5Sb_1.5Te₃ films and bulk materials. The maximum power factor PF of Bi_0.5Sb_1.5Te₃ nanopillars array film is about 3.83?μW?cm^?1 K^?2 at T?=?475?K. Highly oriented (Bi,Sb)₂Te₃ nanocrystalline films with tuned electronic transport properties have potentials in thermoelectric devices.     

Synthesis of n-type Bi2Te1-xSex compounds through oxide reduction process and related thermoelectric properties

We propose a new process for the fabrication of n-type Bi₂Te_3-xSe_x (x = 0, 0.25, 0.4, 0.7) compounds. The compounds could be synthesized successfully using only oxide powders as the starting materials via the mechanical milling, oxidation, reduction, and spark plasma sintering processes. The controllability of the Se content could be ascertained by structural, electrical, and thermal characterizations, and the highest thermoelectric figure of merit (ZT) of 0.84 was achieved in Bi₂Te_2.6Se_0.4 compound at 423 K without any intentional doping. This process provides a new route to fabricate n-type Bi₂Te_3-xSe_x compounds with competitive ZTs using all oxide starting materials.     

Enhanced thermal stability of Bi2Te3-based alloys via interface engineering with atomic layer deposition

The ease of Te sublimation from Bi₂Te₃-based alloys significantly deteriorates thermoelectric and mechanical properties via the formation of voids. We propose a novel strategy based on atomic layer deposition (ALD) to improve the thermal stability of Bi₂Te₃-based alloys via the encapsulation of grains with a ZnO layer. Only a few cycles of ZnO ALD over the Bi₂Te_2.7Se_0.3 powders resulted in significant suppression of the generation of pores in Bi₂Te_2.7Se_0.3 extrudates and increased the density even after post-annealing at 500 °C. This is attributed to the suppression of Te sublimation from the extrudates. The ALD coating also enhanced grain refinement in Bi₂Te_2.7Se_0.3 extrudates. Consequently, their mechanical properties were significantly improved by the encapsulation approach. Furthermore, the ALD approach yields a substantial improvement in the figure-of-merit after the post-annealing. Therefore, we believe the proposed approach using ALD will be useful for enhancing the mechanical properties of Bi₂Te₃-based alloys without sacrificing thermoelectric performance.     

Electrochemical storage mechanism of interstratification-assembled Ti3C2Tx MXene/NiCo-LDHs electrode in alkaline,acid and neutral electrolytes

Different kinds of two-dimensional hybrid electrodes have high theoretical capacitance and energy density. However, the origin of the electrochemical storage mechanism still remains elusive in alkaline, acid and neutral electrolytes. Herein, the interstratification-assembled Ti₃C₂T_x MXene/NiCo-LDHs electrodes were successfully prepared and studied in different electrolytes by in-situ Raman spectroscopy. The results show that H₂O molecules in neutral electrolyte combine with –OH at the end of Ti₃C₂T_x MXene during charging, and debonding occurs during discharge. Similarly, this reaction also occurs in the discharge process with NiCo-LDHs and provides smaller pseudocapacitance characteristics. Although this pseudocapacitance reaction also occurs in acidic and alkaline electrolytes, however, the difference is that the hydrogen ions will promote the electrochemical performance of Ti₃C₂T_x MXene and has a certain corrosion consumption effect on NiCo-LDHs, but generally improve the electrochemical performance of Ti₃C₂T_x MXene/NiCo-LDHs. Interestingly, the OH^? in alkaline electrolyte can promote the electrochemical performance of NiCo-LDHs, and produce a new electrochemical reaction with –F between the layers of Ti₃C₂T_x MXene, which greatly improves the overall electrochemical performance of this hybrid electrodes. As a result, Ti₃C₂T_x MXene/NiCo-LDHs electrodes have the best electrochemical performance in alkaline electrolyte with capacitance of 283 F g^?1, energy density of 14.2 Wh kg^?1 and power density of 3007.1 W kg^?1. This work lays a foundation for the preparation of high-performance two-dimensional hybrid electrochemical energy storage devices.     

High thermoelectric performance of (Bi1-xPrx)2(Te0.9Se0.1)3 alloys prepared by high-pressure sintering method

In this article, n-type (Bi_1-xPr_x)₂(Te_0.9Se_0.1)₃ (x = 0, .002, .004, .008) alloys were fabricated by high-pressure sintering (HPS) method together with annealing. The effect of high pressure and Pr contents on the microstructure and thermoelectric performance of samples were explored in detail. The results show that the HPS samples are composed of nanoparticles. Pr doping has significant impacts on the electrical and thermal transport properties of the Bi₂Te_2.7Se_0.3 alloys. The HPS sample with x = .004 shows the maximum ZT value of .31 at 473 K, which is enhanced by 41% to compare with the Pr-free sample. Annealing can improve the thermoelectric properties by increasing the electrical transport properties and decreasing the thermal conductivity simultaneously. As a result, the highest ZT value of 1.06 is achieved for the annealed sample with x = .004 at 373 K, which is beneficial to the thermoelectric power generation.     

Synergistically optimizing electrical and thermal transport properties of Bi2O2Se ceramics by Te‐substitution

Bi₂O₂Se oxyselenides, characterized with intrinsically low lattice thermal conductivity and large Seebeck coefficient, are potential n‐type thermoelectric material in the mediate temperature range. Given the low carrier concentration of ~10¹⁵ cm^?3 at 300 K, the intrinsically low electrical conductivity actually hinders further enhancement of their thermoelectric performance. In this work, the isovalent Te‐substitution of Se plays an effective role in narrowing the band gap, which notably increases the carrier concentration to ~10¹⁸ cm^?3 at 300 K and the electron conduction activation energy has been lowered significantly from 0.33 to 0.14 eV. As a consequence, the power factor has been improved from 104 μW·K^?2·m^?1 for pristine Bi₂O₂Se to 297 μW·K^?2·m^?1 for Bi₂O₂Se_0.96Te_0.04 at 823 K. Meanwhile, the suppressed lattice thermal conductivity derives from the introduced point defects by heavier Te atoms. The gradually decreased phonon mean free path reflects the increasingly intense phonon scattering. Ultimately, the ZT value attains 0.28 for Bi₂O₂Se_0.96Te_0.04 at 823 K, an enhancement by a factor of ~2 as compared to that of pristine Bi₂O₂Se. This study has demonstrated that Te‐substitution of Se could synergistically optimize the electrical and thermal properties thus effectively enhancing the thermoelectric performance of Bi₂O₂Se.     

Bifunctional Ti3C2Tx–CNT/PANI composite with excellent electromagnetic shielding and supercapacitive performance

Ti₃C₂T_x exhibits excellent electromagnetic (EM) shielding and electrochemical properties. However, the inherent re-stacking tendency and easy oxidation of Ti₃C₂T_x limit its further application. In this study, a multi-walled carbon nanotube/polyaniline composite (CNT/PANI, denoted as C–P) was introduced into Ti₃C₂T_x nanosheets to obtain a Ti₃C₂T_x–CNT/PANI composite (T@CP). Owing to the integrated effects of Ti₃C₂T_x and C–P, the contribution of absorption was significantly improved, which finally enhanced the EM shielding performance of T@CP. The highest total EM shielding effectiveness (SE_T) was close to 50 dB (49.8 dB), which was substantially higher than that of pure Ti₃C₂T_x (45.3 dB). Moreover, T@CP demonstrated outstanding supercapacitive performance. The specific capacitance of T@CP (2134.5 mF/cm² at 2 mV/s) was considerably higher than that of pure Ti₃C₂T_x (414.3 mF/cm² at 2 mV/s). These findings provide a new route for the development of high-efficiency Ti₃C₂T_x-based bifunctional EM shielding and electrochemical materials.     

Manganese dioxide nanosheets decorated on MXene (Ti3C2Tx) with enhanced performance for asymmetric supercapacitors

The incorporation of nanosized pseudocapacitive materials and structure design are general strategies to enhance the electrochemical performance of MXene-based materials. Herein, the decoration of manganese dioxide (MnO₂) nanosheets on MXene (Ti₃C₂T_x) surfaces was prepared by a facile liquid phase coprecipitation method. Ti₃C₂T_x is initially modified by polydopamine (PDA) coating to ensure the homogeneous distribution of MnO₂ nanosheets and tight and close connections between MnO₂ and the Ti₃C₂T_x backbone. Due to the obtained three-dimensional (3D) nanostructure, facilitating electron transport within the electrode and promoting electrolyte ion accessibility, the δ-MnO₂@Ti₃C₂T_x-0.06 electrode yields superior electrochemical performances, such as a rather large areal capacity of 1233.1 mF cm^?2 and high specific capacitance of 337.6 F g^?1 at 2 mV s^?1, as well as high cyclic stability for 10000 cycles. Furthermore, δ-MnO₂@Ti₃C₂T_x-0.06 composites are employed as positive electrodes, and activated carbon (AC) materials act as negative electrodes with an aqueous electrolyte of 1 M Na₂SO₄ to assemble asymmetric supercapacitors. The prototype device is reversible at cell voltages from 0 to 1.8 V, and manifests a maximum energy density of 31.4 Wh kg^?1 and a maximum power density of 2700 W kg^?1. These encouraging results show enormous possibilities for energy storage applications.     

A novel “plane-line-plane” nanostructure of the sandwich-like CNTs@SnO2/Ti3C2Tx 3D nanocomposite as a promising anode for lithium-ion batteries

As one of the novel two-dimensional metal carbides, Ti₃C₂T_x has received intense attention for lithium-ion batteries. However, Ti₃C₂T_x has low intrinsic capacity due to the fact that the surface functionalization of F and OH blocks Li ion transport. Herein a novel “plane-line-plane” three-dimensional (3D) nanostructure is designed and created by introducing the carbon nanotubes (CNTs) and SnO₂ nanoparticles to Ti₃C₂T_x via a simple hydrothermal method. Due to the capacitance contribution of SnO₂ as well as the buffer role of CNTs, the as-fabricated sandwich-like CNTs@SnO₂/Ti₃C₂T_x nanocomposite shows high lithium ion storage capabilities, excellent rate capability and superior cyclic stability. The galvanostatic electrochemical measurements indicate that the nanocomposite exhibits a superior capacity of 604.1 mAh g^?1 at 0.05?A?g^?1, which is higher than that of raw Ti₃C₂T_x (404.9 mAh g^?1). Even at 3?A?g^?1, it retains a stable capacity (91.7 mAh g^?1). This capacity is almost 5.6 times higher than that of Ti₃C₂T_x (16.6 mAh g^?1) and 58 times higher than that of SnO₂/Ti₃C₂T_x (1.6 mAh g^?1). Additionally, the capacity of CNTs@SnO₂/Ti₃C₂T_x for the 50th cycle is 180.1 mAh g^?1 at 0.5?A?g^?1, also higher than that of Ti₃C₂T_x (117.2 mAh g^?1) and SnO₂/Ti₃C₂T_x (65.8 mAh g^?1), respectively.     

Fabrication of 2D titanium carbide MXene/Au nanorods as a nanosensor platform for sensitive SERS detection

As an emerging label-free detection technology, surface-enhanced Raman scattering (SERS) has been used for biological detection, food safety, and environmental pollution owing to its high sensitivity, specificity and rapid response. However, traditional SERS substrates are unstable, prone to agglomeration, and demonstrate low productivity and high production cost. In this work, hybrids of a two-dimensional electron gas (2DEG) Ti₃C₂T_x monolayer and Au nanorods (AuNRs) were fabricated via self-assembly. Ti₃C₂T_x:AuNRs ratios were prepared, and each hybrid's SERS activity was evaluated through 4-aminothiophenol (pATP) detection. The Ti₃C₂T_x/AuNRs-1 substrate exhibited the weakest SERS performance, whereas the Ti₃C₂T_x/AuNRs-3 substrate had the best SERS activity enhancement, with a pATP limit of detection (LOD) of 10⁻⁹ M. When 30 sites on substrates were selected for SERS detection, the relative standard deviation (RSD) was found to be only 7.18 %, revealing the good performance sensitivity and high reproducibility of the Raman signal. The sensitivity of Ti₃C₂T_x/AuNRs-3 was also assessed with respect to a hazardous chemical, 1,2-bis (4-pyridyl) ethylene (BPE), revealing an LOD of 10⁻¹² M. For thiram, the LOD of Ti₃C₂T_x/AuNRs-3 was 10⁻⁸ M, which is considerably lower than the 1 ppm industry safety standard. A relative standard deviation RSD of 7.94 % indicates the high reproducibility and uniformity of the Raman signal of thiram for Ti₃C₂T_x/AuNRs-3. Compared with the LODs of 10⁻⁵ M and 10⁻⁶ M for commercial substrates T-SERS and Au nanorod arrays (AuNRAs), respectively, the 10⁻⁸ M LOD of our synthesized Ti₃C₂T_x/AuNRs indicates good sensitivity. Three kinds of pesticides were detected by Ti₃C₂T_x/AuNRs, and only Raman signal of thiram can be found, revealing the good selectivity for thiram. These results for Ti₃C₂T_x/AuNRs suggest its potential to serve as a novel SERS platform.     

Optimization of chemical and electrochemical parameters for the preparation of n-type Bi2Te2.7Se0.3 thin films by electrodeposition

A 2^3–1 fractional factorial design comprising four runs and three centre points was applied in order to optimize the electrodeposition process to find a compound with the best stoichiometry leading to a Bi₂Te_2.7Se_0.3 thin film suitable for thermoelectric applications. The key factors considered were the deposition potential, the percentage of bismuth and the percentage of selenium in the solution. The Bi^III, Se^IV, Te^IV electrolyte mixtures in 1 M HNO₃ (pH 0), allowed deposition of ternary alloys to be achieved at room temperature on stainless steel substrates. The deposition mechanism was investigated by linear voltammetry. The films were characterized by micropobe analysis, X-ray diffraction, scanning electron microscopy and atomic force microscopy. The XRD patterns of the film show that the as-deposited are polycrystalline and isostructural to Bi₂Te₃. The SEM study shows that the film is covered by crystallites while the AFM image reveals a low level of roughness.     

Substrate temperature-dependent thermoelectric figure of merit of nanocrystalline Bi2Te3 and Bi2Te2.7Se0.3 prepared using pulsed laser deposition supported by DFT study

This work reports the pulsed laser deposition of n-type selenium (Se) doped bismuth telluride (Bi₂Te_2.7Se_0.3) and n-type bismuth telluride (Bi₂Te₃) nanostructures under varying substrate temperatures. The influence of the substrate temperature during deposition on the structural, morphological and thermoelectric properties for each phase was investigated. Density functional theory (DFT) simulations were employed to study the electronic structures of the unit-cells of the compounds as well as their corresponding partial and total densities of states. Surface and structural characterization results revealed highly crystalline nanostructures with abundant grain boundaries. Systematic comparative analysis to determine the effect of Se inclusion into the Bi₂Te₃ matrix on the thermoelectric properties is highlighted. The dependence of the thermoelectric figure of merit (ZT) of the nanostructures on the substrate temperatures during deposition was demonstrated. The remarkable room temperature thermoelectric power factor (PF) of 2765 μW/mK² and 3179 μW/mK² for pure and Se-doped Bi₂Te₃ compounds respectively, signifies their potential of being useful in cooling and power generation purposes. The room temperature ZT values of the Se-doped Bi₂Te₃ was found to be 0.92, about 30% enhancement as compared with the pure phase, which evidently results from the suppressed thermal conductivity in the doped species caused by phonon scattering at the interfaces.     

Subsize Ti3C2Tx derived from molten-salt synthesized Ti3AlC2 for enhanced capacitive deionization

Ti₃C₂T_x is a promising intercalation-type electrode material for capacitive deionization (CDI). However, Ti₃C₂T_x, obtained from traditional synthesized Ti₃AlC₂, is with large particle size and undersized interlayer space, which can easily lead to the longer ion diffusion path, fewer adsorption sites, and higher ion diffusion barrier in CDI process. In this work, subsize and Na⁺ intercalated Ti₃C₂T_x (Na⁺-Ti₃C₂T_x-MS) was prepared by HF etching KCl-assisted molten-salt synthesized Ti₃AlC₂ and following NaOH treatment. The Na⁺-Ti₃C₂T_x-MS achieves a high electrosorption capacity of 14.8 mg/g and a high charge efficiency of 0.81 at the applied voltage of 1.2 V in 100 mg/L NaCl solution. Besides, the stable desalination performance of Na⁺-Ti₃C₂T_x-MS has been confirmed. The superior performance of Na⁺-Ti₃C₂T_x-MS can be attributed to the subsize particle and larger interlayer space. Both two factors can effectively increase ions adsorption sites, shorten diffusion path lengths, and reduce diffusion barriers in the CDI process.     

Cost effective synthesis of CuxBi2-xSe3 photocatalysts by sol-gel method and their enhanced photodegradation and antibacterial activities

A simple sol-gel approach was used to synthesize Cu doped Bismuth Selenide nanoparticles denoted as Cu_xBi_2-xSe₃ (x = 0.1, 0.2), in order to comprehend the effect of Cu-dopant on the photocatalytic and antibacterial activity of Bismuth Selenide. The structural properties of prepared samples were investigated by the XRD technique and results showed the formation of hexagonal Cu_xBi_2-xSe₃ (x = 0.1, 0.2). The average crystallite size of Cu_xBi_2-xSe₃ was found to increase from 39 nm to 42 nm with the increase in the concentration of Cu ions. Atomic force microscopy (AFM) was used to confirm the morphology and particle size of prepared samples. Photoluminescence (PL) studies revealed the decrease in band gap from 1.66 eV to 1.61 eV for Cu_0.1Bi_1.9Se₃ and Cu_0.2Bi_1.8Se₃, respectively. The Raman spectra of Cu_xBi_2-xSe₃ (x = 0.1, 0.2) showed two vibrational modes at 130 cm^?1 and 170 cm^?1. The photocatalytic performance of prepared nanoparticles was evaluated by the removal of methyl blue (MB) and malachite green (MG), under natural sunlight. Cu doped Bismuth Selenide Cu_0.2Bi_1.8Se₃ exhibited higher photocatalytic activity as compared to Cu_0.1Bi_1.9Se₃ and undoped Bismuth Selenide with the 97% and 99% degradation of MB and MG, respectively. Hence, Cu doping proved an efficient way to enhance the photocatalytic response of Bismuth Selenide. Through the antibacterial activity, it was further disclosed that the Cu doped samples had better inhibition zones than undoped Bismuth Selenide. The maximum inhibition zone (29 mm) was observed at optimum doping concentration for Cu_0.2Bi_1.8Se₃. From the results, it can be deduced that Cu_0.2Bi_1.8Se₃ can be as effective photocatalytic and antibacterial agent to treat water pollution.     

Improved photoelectrocatalytic degradation of methylene blue by Ti3C2Tx/Bi12TiO20 composite anodes

In order to effectively reduce the high recombination rate of photogenerated carriers when Bi₁₂TiO₂₀ (BTO) was excited by visible light, Ti₃C₂T_x/BTO/fluorine-doped tin oxide photoanodes were conveniently prepared with the aid of mechanical coating by gentle ultrasonic mixing. Systematic characterization and the degradation of methylene blue in a photoelectrochemical cell were performed. The results showed that the Ti₃C₂T_x/BTO composite exhibited a strong light absorption ability and the effective separation of photogenerated carriers. The optimal anode (6 wt% Ti₃C₂T_x/BTO) degraded 85.4% of methylene blue within 120 min at an applied electric field of 1 V, with a reaction rate that was 3.5 times that of BTO. It was proved that Ti₃C₂T_x, as a useful co-catalyst, creates an internal electric field at the contact interface with BTO and an external electric field, which are responsible for the enhanced photoelectrocatalytic degradation capacity of the composite anode materials.     

Grain boundary engineering strategy for simultaneously reducing the electron concentration and lattice thermal conductivity in n-type Bi2Te2.7Se0.3-based thermoelectric materials

This study demonstrates atomic layer deposition (ALD) of an extremely thin Al₂O₃ layer over n-type Bi₂Te_2.7Se_0.3 to alleviate the adverse effects of multiple boundaries on their thermoelectric performance. Multiple boundaries reduce thermal conductivity (κ), but generate electrons, deviating from the optimum carrier concentration. Only one Al₂O₃ ALD cycle effectively suppresses Te volatilization at the grain boundaries, resulting in a decrease from 5.8 × 10¹⁹/cm³ to 3.6 × 10¹⁹/cm³ in the electron concentration. Concurrently, the one-cycle-Al₂O₃ coating produces fine grains, thus inducing numerous boundaries, ultimately suppressing the lattice κ from 0.64 to 0.33 W/m·K. A further increase in the number of Al₂O₃ cycles leads in a significant rise in the resistance, resulting in degradation of thermoelectric performance. Consequently, the ZT value is increased by 51 % as a result of Al₂O₃ coating with a single ALD cycle. Our approach offers new insights into the simultaneous reduction of the κ and electron concentration in n-type Bi₂Te₃-based materials.