Tapered distributed analogue tunable phase shifter with low insertion and return loss

Some improvements for distributed Schottky diode tunable phase shifters are carried out. First, near- and far-end sections are tapered to improve return loss. Then, to reduce device length, and the number of varactors, inductances are added in series with the varactors, leading to an improved C/sub max//C/sub min/ ratio. For a 360/spl deg/ tunable phase shifter working at 1 GHz, insertion losses are limited to 2.4 dB maximum. Return loss is better than 20 dB. The tapered sections allow a wide working frequency range, typically from 800 to 1200 MHz with the same characteristics: around 2.4 dB insertion losses, 20 dB return loss.     

Distributed 2- and 3-bit W-band MEMS phase shifters on glass substrates

This paper presents state-of-the-art RF microelectromechanical (MEMS) phase shifters at 75-110 GHz based on the distributed microelectromechanical transmission-line (DMTL) concept. A 3-bit DMTL phase shifter, fabricated on a glass substrate using MEMS switches and coplanar-waveguide lines, results in an average loss of 2.7 dB at 78 GHz (0.9 dB/bit). The measured figure-of-merit performance is 93/spl deg//dB-100/spl deg//dB (equivalent to 0.9 dB/bit) of loss at 75-110 GHz. The associated phase error is /spl plusmn/3/spl deg/ (rms phase error is 1.56/spl deg/) and the reflection loss is below -10 dB over all eight states. A 2-bit phase shifter is also demonstrated with comparable performance to the 3-bit design. It is seen that the phase shifter can be accurately modeled using a combination of full-wave electromagnetic and microwave circuit analysis, thereby making the design quite easy up to 110 GHz. These results represent the best phase-shifter performance to date using any technology at W-band frequencies. Careful analysis indicates that the 75-110-GHz figure-of-merit performance becomes 150/spl deg//dB-200/spl deg//dB, and the 3-bit average insertion loss improves to 1.8-2.1 dB if the phase shifter is fabricated on quartz substrates.     

New miniature 15-20-GHz continuous-phase/amplitude control MMICs using 0.18-/spl mu/m CMOS technology

The design and performance of two new miniature 360/spl deg/ continuous-phase-control monolithic microwave integrated circuits (MMICs) using the vector sum method are presented. Both are implemented using commercial 0.18-/spl mu/m CMOS process. The first phase shifter demonstrates all continuous phase and an insertion loss of 8 dB with a 37-dB dynamic range from 15 to 20 GHz. The chip size is 0.95 mm /spl times/ 0.76 mm. The second phase shifter can achieve all continuous phase and an insertion loss of 16.2 dB with a 38.8-dB dynamic range at the same frequency range. The chip size is 0.71 mm /spl times/ 0.82 mm. To the best of the authors' knowledge, these circuits are the first demonstration of microwave CMOS phase shifters using the vector sum method with the smallest chip size for all MMIC phase shifters with 360/spl deg/ phase-control range above 5 GHz reported to date.     

A 1-GHz active phase shifter with a ferroelectric varactor

An active phase shifter circuit implemented with discrete components is reported. The tuning element, a ferroelectric varactor, is a parallel plate capacitor with Ba/sub 0.5/Sr/sub 0.5/TiO/sub 3/ (BST) as the dielectric. The circuit consists of two bipolar junction transistors coupled with a feedback network, which contains the varactor and thus produces a transfer function that can be varied with a control voltage. The active nature of the circuit allows for signal gain, while the BST varactor provides a high-Q tuning element. This represents an improvement over strictly passive phase shifters with ferroelectric elements. Circuit simulation results are presented and compared with measured data from the implemented system. The network, even with markedly nonideal transistors, can provide a true all-pass response over the frequency band of interest (200-1100 MHz). The measurement results demonstrate an analog tunability of about 100/spl deg/ with a gain variation of about 0.6 dB at I GHz when using a BST capacitor with a tunability of 2.75:1.     

Distributed phase shifter with pyrochlore bismuth zinc niobate thin films

A monolithic Ku-band phase shifter employing voltage tunable Bi/sub 1.5/Zn/sub 1.0/Nb/sub 1.5/O/sub 7/ (BZN) thin film parallel plate capacitors is reported. BZN films were deposited by radio frequency magnetron sputtering on single-crystal sapphire substrates. A nine-section distributed coplanar waveguide loaded-line phase-shifter structure was designed. A differential phase shift of 175/spl deg/ was achieved with a maximum insertion loss of 3.5 dB at 15 GHz, giving a figure of merit /spl sim/50/spl deg//dB. To the best of our knowledge, this is the first demonstration of a monolithic tunable microwave circuit using BZN thin films.     

W-band CPW RF MEMS circuits on quartz substrates

This paper presents W-band coplanar waveguide RF microelectromechanical system (MEMS) capacitive shunt switches with very low insertion loss (-0.2 to -0.5 dB) and high-isolation (/spl les/ -30 dB) over the entire W-band frequency range. It is shown that full-wave electromagnetic modeling using Sonnet can predict the performance of RF MEMS switches up to 120 GHz. Also presented are W-band 0/spl deg//90/spl deg/ and 0/spl deg//180/spl deg/ switched-line phase shifters with very good insertion loss (1.75 dB/bit at 90 GHz) and a wide bandwidth of operation (75-100 GHz). These circuits are the first demonstration of RF MEMS digital-type phase shifters at W-band frequencies and they outperform their solid-state counterparts by a large margin.     

Linear tunable phase shifter using a left-handed transmission line

We demonstrate a compact, linear, and low loss variation hybrid phase shifter using a left-handed (LH) transmission line. For frequencies from 4.3 to 5.6 GHz, this phase shifter gives a nearly linear phase variation with voltage, with a maximum deviation of /spl plusmn/7.5/spl deg/. Within this frequency range, the maximum insertion loss is 3.6 dB, and the minimum insertion loss is 1.8 dB over a continuously adjustable phase range of more than 125/spl deg/, while minimum return loss is only 10.2 dB. Furthermore, this phase shifter requires only one control line, and it consumes almost no power.     

On the feasibility of CMOS multiband phase shifters for multiple-antenna transmitters

We present the design of an integrated multiband phase shifter in RF CMOS technology for phased array transmitters. The phase shifter has an embedded classical distributed amplifier for loss compensation. The phase shifter achieves a more than 180/spl deg/ phase tuning range in a 2.4-GHz band and a measured more than 360/spl deg/ phase tuning range in both 3.5-GHz and 5.8-GHz bands. The return loss is less than -10dB at all conditions. The feasibility for transmitter applications is verified through measurements. The output power at a 1-dB compression point (P/sub 1 dB/) is as high as 0.4dBmat 2.4GHz. The relative phase deviation around P/sub 1 dB/ is less than 3/spl deg/. The design is implemented in 0.18-/spl mu/mRF CMOS technology, and the chip size is 1200/spl mu/m /spl times/ 2300 /spl mu/m including pads.     

RF MEMS phase shifters based on PCB MEMS technology

An X-band main-line type loaded line RF MEMS phase shifter fabricated using printed circuit based MEMS technology is reported. The phase shifter provides a phase shift of 31.6/spl deg/ with a minimum insertion loss of 0.56 dB at 9 GHz for an applied DC bias voltage of 40 V. These phase shifters are suitable for monolithic integration with low-cost phased arrays on Teflon or Polyimide such as low dielectric constant substrates.     

A scalable reflection type phase shifter with large phase variation

We describe a reflection type phase shifter which exhibits a large phase shift range. We characterized its response between 1.95 GHz and 2.15 GHz and achieved over 400/spl deg/ phase shift with less than 4dB insertion loss. The transition time from 0/spl deg/ to 180/spl deg/ is <20 nS. Our design is scalable to mm-wave operation because it uses no inductors.     

Distributed MEMS analog phase shifter with enhanced tuning

The design, fabrication, and measurement of a tunable microwave phase shifter is described. The phase shifter combines two techniques: a distributed capacitance transmission line phase shifter, and a large tuning range radio frequency (RF) microelectromechanical system (MEMS) capacitor. The resulting device is a large bandwidth, continuously tunable, low-loss phase shifter, with state-of-the-art performance. Measurements indicate analog tuning of 170/spl deg/ phase shift per dB loss is possible at 40 GHz, with a 538/spl deg/ phase shift per centimeter. The structure is realized with high-Q MEMS varactors, capable of tuning C/sub max//C/sub min/= 3.4. To our knowledge, this presents the lowest loss analog millimeter wave phase shifter performance to date.     

A compact V-band 2-bit reflection-type MEMS phase shifter

Air-gap overlay CPW couplers and low-loss series metal-to-metal contact microelectromechanical system (MEMS) switches have been employed to reduce the loss of reflection-type MEMS phase shifters at V-band. Phase shift is obtained by changing the lengths of the open-ended stubs using series MEMS switches. A 2-bit [135] reflection-type MEMS phase shifter showed an average insertion loss of 4 dB with return loss better than 11.7 dB from 50 to 70 GHz. The chip is very compact with a chip size as small as 1.5 mm /spl times/ 2.1 mm.     

An X-band 22.5°/45° digital phase shifter based on switched filter networks

The design approach and performance of a 22.5°/45°digital phase shifter based on a switched filter network for X-band phased arrays are described. Both the MMIC phase shifters are fabricated employing a 0.25μm gate GaAs pHEMT process and share in the same chip size of 0.82×1.06 mm². The measurement results of the proposed phase shifters over the whole operating frequency range show that the phase shift error is less than 22.5°±2.5°, 45°±3.5°, which shows an excellent agreement with the simulated performance, the insertion loss is within the range of 0.9-1.2 dB for the 22.5°phase shifter and 0.9-1.4 dB for the 45°phase shifter, and the input/output return loss is better than -12.5 and -11 dB respectively. They also achieve the similar P_1dB continuous wave power handing capability of 24.8 dBm at 10 GHz. The phase shifters show a good phase shift error, insertion loss and return loss in the X-band (40%), which can be employed into the wide bandwidth multi-bit digital phase shifter.     

A 2-bit miniature X-band MEMS phase shifter

The design and performance of a compact low-loss X-band true-time-delay (TTD) MEMS phase shifter fabricated on 8-mil GaAs substrate is described. A semi-lumped approach using microstrip transmission lines and metal-insulator-metal (MIM) capacitors is employed for the delay lines in order to both reduce circuit size as well as avoid the high insertion loss found in typical miniaturized designs. The 2-bit phase shifter achieved an average insertion loss of -0.70 dB at 9.45 GHz, and an associated phase accuracy of /spl plusmn/1.3/spl deg/. It occupies an area of only 5 mm/sup 2/, which is 44% the area of the smallest known X-band MEMS phase shifter . The phase shifter operates over 6-14 GHz with a return loss of better than -14 dB.     

An impedance matched phase shifter using BaSrTiO/sub 3/ thin film

We present a distributed phase shifter with an equal ripple return loss at its operation frequency range. The phase shifter is based on a periodic structure and consists of a coplanar waveguide (CPW) line periodically loaded with voltage-variable barium strontium titanate (BST) interdigitated capacitors. Measurements show that its return loss is better than -15dB at frequencies from direct current to 16GHz, and at 9.4GHz, its phase shift is 41/spl deg/ under 120-V applied bias voltage.     

Design and modeling of 4-bit slow-wave MEMS phase shifters

A true-time-delay multibit microelectromechanical systems (MEMS) phase-shifter topology based on impedance-matched slow-wave coplanar-waveguide sections on a 500-/spl mu/m-thick quartz substrate is presented. A semilumped model for the unit cell is derived and its equivalent-circuit parameters are extracted from measurement and electromagnetic simulation data. This unit cell model can be cascaded to accurately predict N-section phase-shifter performance. Experimental data for a 4.6-mm-long 4-bit device shows a maximum phase error of 5.5/spl deg/ and S/sub 11/ less than -21 dB from 1 to 50 GHz with worst case S/sub 21/ less than -1.2 dB. In a second design, the slow-wave phase shifter was additionally loaded with MEMS capacitors to result in a phase shift of 257/spl deg//dB at 50 GHz, while keeping S/sub 11/ below -19 dB (with S/sub 21/<-1.9 dB). The beams are actuated using high-resistance SiCr bias lines with typical actuation voltage around 30-45 V.     

Continuous Varactor-Diode Phase Shifter with Optimized Frequency Response

A method is introduced for designing continuous varactor-diode phase shifters with optimum frequency response. The circuit used gives very small frequency variations of the phase shift if the maximum phase shift of the device is less than about 200/spl deg/. Measurement results on a 180/spl deg/ L-band phase shifter are presented. This unit gives less than 5/spl deg/ variation of any given phase shift less than 180/spl deg/, when the frequency is changed from 1.5 to 1.7 GHz.     

0.13-μm CMOS Phase Shifters for X-, Ku-, and K-Band Phased Arrays

Two 4-bit active phase shifters integrated with all digital control circuitry in 0.13-mum RF CMOS technology are developed for X- and Ku-band (8-18 GHz) and K-band (18-26 GHz) phased arrays, respectively. The active digital phase shifters synthesize the required phase using a phase interpolation process by adding quadrature-phased input signals. The designs are based on a resonance-based quadrature all-pass filter for quadrature signaling with minimum loss and wide operation bandwidth. Both phase shifters can change phases with less than about 2 dB of RMS amplitude imbalance for all phase states through an associated DAC control. For the X- and Ku-band phase shifter, the RMS phase error is less than 10^o over the entire 5-18 GHz range. The average insertion loss ranges from to at 5-20 GHz. The input for all 4-bit phase states is typically at -5.4 plusmn1.3 GHz in the X- and Ku-band phase shifter. The K-band phase shifter exhibits 6.5-13 of RMS phase error at 15-26 GHz. The average insertion loss is from 4.6 to at 15-26 GHz. The input of the K-band phase shifter is at 24 GHz. For both phase shifters, the core size excluding all the pads and the output 50 Omega matching circuits, inserted for measurement purpose only, is very small, 0.33times0.43 mm² . The total current consumption is 5.8 mA in the X- and Ku-band phase shifter and 7.8 mA in the K-band phase shifter, from a 1.5 V supply voltage.     

K-band HBT and HEMT monolithic active phase shifters using vector sum method

Two monolithic 3-bit active phase shifters using the vector sum method to K-band frequencies are reported in this paper. They are separately implemented using commercial 6-in GaAs HBT and high electron-mobility transistor (HEMT) monolithic-microwave integrated-circuit (MMIC) foundry processes. The MMIC HBT active phase shifter demonstrates an average gain of 8.87 dB and a maximum phase error of 11/spl deg/ at 18 GHz, while the HEMT phase shifter has 3.85-dB average measured gain with 11/spl deg/ maximum phase error at 20 GHz. The 20-GHz operation frequency of this HEMT MMIC is the highest among all the reported active phase shifters. The analysis for gain deviation and phase error of the active phase shifter using the vector sum method due to the individual variable gain amplifiers is also presented. The theoretical analysis can predict the measured minimum root-mean-square phase error 4.7/spl deg/ within 1/spl deg/ accuracy.     

Design and performance of a new digital phase shifter at X-band

A new digital phase shifter design at X-band is presented. The phase shifter operates based on converting a microstrip line to a rectangular waveguide and thus achieving the phase shift by changing the wave propagation constant through the medium. As a proof of principle, a 3-b phase shifter has been designed and constructed using PIN diode switches. An average insertion loss of 1.95 dB and phase shift error of less than 4/spl deg/ at 10.6 GHz are achieved.