Reliability of 80 μm pitch flip chip attachment on flex

The interest toward flip chip technology has increased rapidly during last decade. Compared to the traditional packages and assembly technologies flip chip has several benefits, like less parasitics, the small package size and the weight. These properties emphasize especially when flip chip component is mounted direct to the flexible printed board. In this paper flip chip components with Kelvin four point probe and daisy chain test structure were bonded to the polyimide flex with two different types of anisotropically conductive adhesive films and one anisotropically conductive adhesive paste. The reliability of small pitch flip chip on flex interconnections (pitch 80 μm) was tested in 85°C/85% RH environmental test and −40↔+125°C thermal shock test. According to the results it is possible to achieve reliable and stable ohmic contact, even in small pitch flip chip on flex applications.     

Anisotropic conductive film flip chip joining using thin chips

In this study, flip chip interconnections were made on very flexible polyethylene naphthalate substrates using anisotropic conductive film. Two kinds of chips were used: chips of normal thickness and thin chips. The thin chips were very thin, only 50 μm thick. Due to the thinness of the chips they were flexible and the entire joint was bendable. The reliability properties of the interconnections established with these two different kinds of chips were compared. In addition, the effect of bending of the chip and joint area on the joint reliability was studied. Furthermore, part of the substrates was dried before bonding and the effect of that on the joint performance was investigated.The pitch of the test vehicles was 250 μm and the chips had 25 μm high gold bumps. For resistance analysis there were two four-point measuring positions in each test vehicle. For finding the optimal bonding conditions for the test vehicles, the bonding was done using two different bonding pressures, of which the better one was chosen for the final tests.Furthermore, the test vehicles were subjected to thermal cycling tests between −40 and +125 °C (half-an-hour cycle) and to a humidity test (85%/85 °C). Part of the test vehicles were bent during the tests. Finally, the structures of the joints were studied using scanning electron microscopy.     

Flip chip attachment on flexible LCP substrate using an ACF

In this study the reliability of a flip chip bonding process using anisotropic conductive adhesives (ACA) was evaluated. The flexible substrates used were made of liquid crystal polymer (LCP), which is an interesting new material having excellent properties for flexible printed circuit boards. The test samples were prepared using two different anisotropic conductive films (ACF) having the same fast-cure resin matrix, but different conductive particles. The reliability of the test samples was studied by accelerated environmental tests. In the constant humidity test the temperature was 85 °C and the relative humidity was 85%. The temperature cycling test was carried out between temperatures of −40 °C and 85 °C. To determine the exact time of a failure the resistance of each test sample was measured using continuous real-time measurement. A clear difference between the behaviour of the conductive particles was seen in the test. While the adhesive having polymer particles had only one failure during testing, the adhesive having nickel particles had a considerable number of failures in both tests. Cross sections of the samples were made to analyze the failure mechanisms.     

Effects of bonding temperature on the properties and reliabilities of anisotropic conductive films (ACFs) for flip chip on organic substrate application

The effects of bonding temperatures on the composite properties and reliability performances of anisotropic conductive films (ACFs) for flip chip on organic substrates assemblies were studied. As the bonding temperature decreased, the composite properties of ACF, such as water absorption, glass transition temperature (T_g), elastic modulus (E′) and coefficient of thermal expansion (α), were improved. These results were due to the difference in network structures of cured ACFs which were fully cured at different temperatures. From small angle X-ray scattering (SAXS) test result, ACFs cured at lower temperature, had denser network structures. The reliability performances of flip chip on organic substrate assemblies using ACFs were also investigated as a function of bonding temperatures. The results in thermal cycling test (−55 °C/+150 °C, 1000 cycles) and PCT (121 °C, 100% RH, 96 h) showed that the lower bonding temperature resulted in better reliability of the flip chip interconnects using ACFs. Therefore, the composite properties of cured ACF and reliability of flip chip on organic substrate assemblies using ACFs were strongly affected by the bonding temperature.     

Reliability of adhesive joined thinned chips on flexible substrates under humid conditions

Thin chips are an interesting option for reducing the thickness of an electronics package. In addition to the reduced size, thinned chips are flexible and can dissipate more heat than thicker ones. Joining of the thin chips can be done using several different techniques. Of these, anisotropic conductive adhesives (ACA) are an interesting option as they have several advantages, such as low bonding temperature and capability for high density interconnections. The reliability of ACA flip chip joints under thermal cycling conditions has been found to increase when thinned chips are used. However, the effect of humidity has not been fully explored. In this study the reliability of thinned chips (50 μm) under humid conditions was investigated using thin flexible substrates. Seven test lots were assembled with thinned chips using two different ACA films and liquid crystal polymer (LCP), polyimide (PI) and thin FR-4 substrates. A high humidity and high temperature test was used to study the reliability of the interconnections. A finite element model (FEM) was used to analyse the stresses in the test samples during testing. Several failures occurred during the test and significant differences between the substrates were seen. Additionally, bonding pressure was found to be a critical factor for the reliability under the humid conditions.     

Highly reliable non-conductive adhesives for flip chip CSP applications

Non-conductive adhesives (NCA), widely used in display packaging and fine pitch flip chip packaging technology, have been recommended as one of the most suitable interconnection materials for flip-chip chip size packages (CSPs) due to the advantages such as easier processing, good electrical performance, lower cost, and low temperature processing. Flip chip assembly using modified NCA materials with material property optimization such as CTEs and modulus by loading optimized content of nonconductive fillers for the good electrical, mechanical and reliability characteristics, can enable wide application of NCA materials for fine pitch first level interconnection in the flip chip CSP applications. In this paper, we have developed film type NCA materials for flip chip assembly on organic substrates. NCAs are generally mixture of epoxy polymer resin without any fillers, and have high CTE values un-like conventional underfill materials used to enhance thermal cycling reliability of solder flip chip assembly on organic boards. In order to reduce thermal and mechanical stress and strain induced by CTE mismatch between a chip and organic substrate, the CTE of NCAs was optimized by filler content. The flip chip CSP assembly using modified NCA showed high reliability in various environmental tests, such as thermal cycling test (-55/spl deg/C/+160/spl deg/C, 1000 cycle), high temperature humidity test (85/spl deg/C/85%RH, 1000 h) and high temperature storage test (125/spl deg/C, dry condition). The material properties of NCA such as the curing profile, the thermal expansion, the storage modulus and adhesion were also investigated as a function of filler content.     

Study of adhesive flip chip bonding process and failure mechanisms of ACA joints

The flip chip bonding process using anisotropic conductive adhesives (ACA) and the consequent joint reliability were studied. The substrates used were rigid FR-4 boards, which are interesting due to their low cost and wide range of applications. The problems associated with the technique are discussed in this paper from the reliability point of view. Also, some aspects concerning production are introduced.The reliability of the joints was studied by accelerated environmental tests. A temperature cycling test was performed between temperatures −40 and +125 °C. Constant humidity testing was conducted at 85 °C and RH85%. In addition, reflow aging tests were performed using a conventional Sn/Pb reflow profile. For reducing the bonding cycle time, a two-stage curing process was used, which also utilizes the reflow process.The results show that the three bonding parameters, temperature, time, and pressure, all affect joint reliability. Most detrimental, however, seems to be reflow treatment performed after bonding. Most failures occurred only very briefly during the temperature cycling at the moment the temperature changed, while the joints were still conducting at both temperature extremes. However, a different failure mechanism caused a different kind of behavior during temperature cycling. The relationship between the failure modes and the failure mechanisms was studied using a scanning electron microscopy.     

A study on thermal cycling (T/C) reliability of anisotropic conductive film (ACF) flip chip assembly for thin chip-on-board (COB) packages

In this work, thermal cycling (T/C) reliability of anisotropic conductive film (ACF) flip chip assemblies having various chip and substrate thicknesses for thin chip-on-board (COB) packages were investigated. In order to analyze T/C reliability, shear strains of six flip chip assemblies were calculated using Suhir’s model. In addition, correlation of shear strain with die warpage was attempted.The thicknesses of the chips used were 180 μm and 480 μm. The thicknesses of the substrates were 120, 550, and 980 μm. Thus, six combinations of flip chip assemblies were prepared for the T/C reliability test. During the T/C reliability test, the 180 μm thick chip assemblies showed more stable contact resistance changes than the 480 μm thick chip assemblies did for all three substrates. The 550 μm thick substrate assemblies, which had the lowest CTE among three substrates, showed the best T/C reliability performance for a given chip thickness.In order to investigate what the T/C reliability performance results from, die warpages of six assemblies were measured using Twyman–Green interferometry. In addition, shear strains of the flip chip assemblies were calculated using measured material properties of ACF and substrates through Suhir’s 2-D model. T/C reliability of the flip chip assemblies was independent of die warpages; it was, however, in proportion to calculated shear strain. The result was closely related with material properties of the substrates. The T/C reliability of the ACF flip chip assemblies was concluded to be dominatingly dependent on the induced shear strains of ACF layers.     

Reliability study of underfill/chip interface under accelerated temperature cycling (ATC) loading

Interface reliability issue has become a major concern in developing flip chip assembly. The CTE mismatch between different material layers may induce severe interface delamination reliability problem. In this study, multifunctional micro-moiré interferometry (M³I) system was utilized to study the interfacial response of flip chip assembly under accelerated thermal cycling (ATC) in the temperature range of −40 °C to 125 °C. This in-situ measurement provided good interpretation of interfacial behavior of delaminated flip chip assembly. Finite element analysis (FEA) was carried out by introducing viscoelastic properties of underfill material. The simulation results were found to be in good agreement with the experimental results. Interfacial fracture mechanics was used to quantify interfacial fracture toughness and mode mixity of the underfill/chip interface under the ATC loading. It was found that the interfacial toughness is not only relative to CTE mismatch but also a function of stiffness mismatch between chip/underfill.     

Assembly of Copper Column Interconnect Flip Chip

This paper addresses a new flip chip interconnection technology, flexible flip chip connection (F2C2) technology, for attaching silicon chips to a chip carrier using flexible copper wires. F2C2 is a novel approach to create area array flip chip interconnections using a matrix block of wires encapsulated with a heat-resistant, dissolvable substance. A slice from the wire matrix ingot is first attached to the chip using solder. The other end of the slice is then matched and soldered to the footprint of a substrate. Finally, the encapsulating, dissolvable substance is removed from the body of the slice, leaving the chip attached to the carrier by the inter- disposed, flexible copper wires. The compliant copper wire interconnections can accommodate the coefficient of thermal expansion (CTE) mismatch problem between die and substrate, thus eliminating the need for underfill.     

Fatigue analysis of high-speed photodiode submodule by using FEM

Higher frequencies, super high-speed, and low-cost demands in wireless communication devices have lead to high density packaging technologies such as flip chip interconnections and multichip modules, as substitutes for wire bonding interconnection. Solder is widely used to connect chips to their packaging substrates in flip chip technology and surface mount technology. We constructed global full 3-D FE models for one photodiode on a submount to predict the fatigue life of solder interconnects during an accelerated thermal cycling testing. The 3-D FE models applied is based on the Darveaux approach does this approach have a non-linear viscoplastic analysis. In the bump structural photodiode submodule, the shortest fatigue life of 233 cycles was obtained at the thermal cycling testing condition from −65 to 150 °C. The bump material, rather than submount material, affected and varied the fatigue life. Also, The fatigue life is decreased with increase in creep strain energy density.     

Procedure for design optimization of a T-cap flip chip package

In this study, a 1/4 three-dimensional finite element model of a T-cap flip chip package containing the substrate, underfill, solder bump, silicon die, metal cap and cap attachment was established to conduct thermo-mechanical reliability study during the flip chip fabrication processes. The applied thermal load was cooled from 183 °C to ambience 25 °C to determine the thermal stress and warpage during the curing period of solder ball mounting process. Under fixed geometry, two levels of underfill, metal caps and cap attachments were used to conduct the 2³ factorial design for determining reliable material combinations. The statistical tests revealed that the significant effects affecting the thermal stress were the underfill, metal cap, cap attachment and the interaction between the underfill and cap attachment. The metal cap, cap attachment and their interaction significantly affected the warpage. The proposed regression models were used to perform the surface response simulations and were useful in selecting suitable materials for constructing the package. This study provides a powerful strategy to help the designer to easily determine reliable packaging structures under various reliability considerations.     

Rapid power cycling of flip-chip and CSP components on ceramic substrates

Power cycling has been done for flip-chip and CSP components solder joined onto ceramic substrates. Cycle periods as short as 1 min were applied in the experiments where the chip temperature varied between about 30°C in the power off-state and 100–150°C in the power on-state. Disconnections of the joints were found after 4000–17 000 power cycles. The flip-chip components joined onto low temperature cofired ceramic substrate showed slightly better reliability than the components joined onto alumina substrate. Most of the samples showed clear effects of deterioration of the joints seen as increasing chip temperature for power on-state. The experimental results are compared with calculations based on modified Coffin–Manson equation as well as with one-dimensional simulations.     

Effect of Gold Stud Bump Topology on Reliability of Flip Chip on Flex Interconnects

The flip chip technique using conductive adhesives have emerged as a good alternative to solder flip chip methods. Different approaches of the interconnection mechanism using conductive adhesives have been developed. In this paper, test chips with gold stud bumps are flip-chipped with conductive adhesives onto a flexible substrate. An experimental study to characterize the bonding process parameters is reported. Initial results from the environmental studies show that thermal shock test causes negligible failure. On the other hand, high humidity test causes considerable failure in flip chip on flex assemblies. Improvements in the reliability of the assembly are achieved by modifying the shape of the gold stud bumps.     

Qualification approaches and thermal cycle test results for CSP/BGA/FCBGA

Qualification of newly developed multifunctional electronic packages, e.g. system in a package (SIP), are becoming complex at the package level and even more at the assembly and system levels. After many years of data collection, just recently industry agreed to release an industry-wide specification for single die area array package assembly qualification.Probability risk assessment, being implemented by NASA for space flight missions, may be narrowed at the element level for advanced electronic systems and SIP, and further narrowed at the electronic subsystem level. This paper will review the key elements of an industry-wide specification recently published by the IPC (association connecting electronics industries). It will report on a few other unique qualification approaches that are currently being either implemented or developed for risk reduction in high reliability applications. Risk level assessment based 2-P, 3-P, and LogNormal distributions will be compared for plastic ball grid array (PBGA) and flip chip BGA (FCBGA). For this case, risks are compared using cycles-to-failures (CTFs) test results for temperature ranges of −30 to 100 °C and 0 to 100 °C (two profiles).In addition, CTFs up to 1,500 cycles in the range of −55 to 125 °C for a 784 I/O FCBGA (flip chip BGA, a 175 I/O FPBGA (fine pitch BGA)), and a 313 I/O PBGA (plastic BGA) are compared. Inspection results along with scanning electron microscopy and optical cross-sectional photos revealing damage and failure mechanisms are also included.     

Flexible Chip-on-Flex (COF) and embedded Chip-in-Flex (CIF) packages by applying wafer level package (WLP) technology using anisotropic conductive films (ACFs)

Due to increasing demand for higher performance, greater flexibility, smaller size, and lighter weight in electronic devices, extensive studies on flexible electronic packages have been carried out. However, there has been little research on flexible packages by wafer level package (WLP) technology using anisotropic conductive films (ACFs) and flex substrates, an innovative packaging technology that requires fewer process steps and lower process temperature, and also provides flexible packages. This study demonstrated and evaluated the reliability of flexible packages that consisted of a flexible Chip-on-Flex (COF) assembly and embedded Chip-in-Flex (CIF) packages by applying a WLP process.The WLP process was successfully performed for the cases of void-free ACF lamination on a 50 μm thin wafer, wafer dicing without ACF delamination, and a flip-chip assembly which showed stable bump contact resistances. The fabricated COF assembly was more flexible than the conventional COF whose chip thickness is about 700 μm. To evaluate the flexibility of the COF assembly, a static bending test was performed under different bending radiuses: 35 mm, 30 mm, 25 mm, and 20 mm. Adopting optimized bonding processes of COF assembly and Flex-on-Flex (FOF) assembly, CIF packages were then successfully fabricated. The reliability of the CIF packages was evaluated via a high temperature/humidity test (85 °C/85% RH) and high temperature storage test (HTST). From the reliability test results, the CIF packages showed excellent 85 °C/85% RH reliability. Furthermore, guideline of ACF material property was suggested by Finite Element Analysis (FEA) for better HTST reliability.     

Humidity and reflow resistance of flip chip on foil assemblies with conductive adhesive joints

The drive toward new first level interconnection technologies is running in parallel with the need to study their reliability as such, as well as in further processes such as second level reflow soldering. Both material properties and process settings have a significant effect on the reliability of adhesive interconnections of flip chips on flexible foil substrates. Integrated circuits (ICs) with pitches of 200 and 300 /spl mu/m bonded on two different foil types were subjected to various moisture preconditioning treatments, and subsequently reflow soldered. Measurements of the daisy chain resistance are used to monitor the yield before and after reflow testing, and to qualify the endurance behavior in the 85/spl deg/C/85% RH stress test. We address here the possible failure mechanisms.     

SMT-compatibility of adhesive flip chip on foil interconnections with 40-/spl mu/m pitch

The manufacturing and reliability of a novel type of first-level interconnections is described. Anisotropic conductive and nonconductive adhesives are used to electrically bond flip chip ICs with a pitch of 60 and 40 /spl mu/m to flexible substrates. Analyses cover the initial state of the samples as well as their performance in the JEDEC moisture sensitivity level assessment and subsequent life testing. From the different behavior of the two types of adhesives a failure mechanism issues for the reflow-soldering test.     

Compound semiconductor activation energy in humidity

Product reliability investigations typically include accelerated humidity testing. Originally, the “standard” test was a biased 85 °C/85% relative humidity (RH) lifetest for 1000 h. Recently, a substitute accelerated version of this test has been used. The accelerated version is called highly accelerated stress test (HAST). The HAST conditions are also biased, at 130 °C, 85%RH, and approximately 18 PSI overpressure. The duration of the HAST test is normally 96–100 h – to be equivalent to the 85/85 test. This study is intended to investigate thermal acceleration and show that equivalent HAST tests on compound semiconductors are more highly accelerated and could be conducted with much shorter durations.     

Board level reliability assessment of chip scale packages

A large program had been initiated to study the board level reliability of various types of chip scale package (CSP). The results on six different packages are reported here, which cover flex interposer CSP, rigid interposer CSP, wafer level assembly CSP, and lead frame CSP. The packages were assembled on FR4 PCBs of two different thicknesses. Temperature cycling tests from −40°C to +125°C with 15 min dwell time at the extremes were conducted to failure for all the package types. The failure criteria were established based on the pattern of electrical resistance change. The cycles to failure were analyzed using Weibull distribution function for each type of package. Selected packages were tested in the temperature/humidity chamber under 85°C/85%RH for 1000 h. Some assembled packages were tested in vibration condition as well. In all these tests, the electrical resistance of each package under testing was monitored continuously. Test samples were also cross-sectioned and analyzed under a Scanning Electronic Microscope (SEM). Different failure mechanisms were identified for various packages. It was noted that some packages failed at the solder joints while others failed inside the package, which was packaging design and process related.