A merged CMOS LNA and mixer for a WCDMA receiver

A low-noise amplifier (LNA) and mixer circuit in 0.35-/spl mu/m CMOS operates at 2.1 GHz. Merging the LNA and mixer lowers the number of transistors in the signal path and thereby also the nonlinearity and power consumption. The circuit meets the specifications for a direct conversion wide-band code-division multiple access (WCDMA) receiver. Its noise figure is 3.4 dB (5kHz to 5MHz), the total conversion gain is 23 dB, the third-order input-referred intercept point is -1.5 dBm, and the local oscillator leakage to the antenna is less than -71 dBm. The fully differential circuit takes 8 mA from a 2.7-V supply.     

An integrated low power highly linear 2.4-GHz CMOS receiver front-end based on current amplification and mixing

A low power 2.4-GHz complementary metal oxide semiconductor (CMOS) receiver front-end using highly linear mixer based on current amplification and mixing is reported. In the proposed mixer, linearity is greatly improved by using current mirror amplifier and transconductance linearization using multiple gated transistors. Single IF direct conversion receiver (DCR) architecture is used to achieve higher level of integration and to relax the problem of DCR. The fully integrated receiver front end is fabricated in 0.18-/spl mu/m CMOS technology and HP3 of -9 dBm with a gain of 32 dB and noise figure of 6.5 dB are obtained at 8.8 mW power consumption.     

A 0.13 /spl mu/m CMOS front-end, for DCS1800/UMTS/802.11b-g with multiband positive feedback low-noise amplifier

This paper presents a fully integrated CMOS receiver front-end based on a direct conversion architecture for UMTS/802.11b-g and a low-IF architecture at 100 kHz for DCS1800. The two key building blocks are a multiband low-noise amplifier (LNA) that uses positive feedback to improve its gain and a highly linear mixer. The front-end, integrated in a 0.13 /spl mu/m CMOS process, exhibits a minimum noise figure of 5.2 dB, a programmable gain that can be varied from 13.5 to 28.5 dB, an IIP3 of more than -7.5 dBm and an IIP2 better than 50 dBm. The total current consumption is 20mA from a 1.2V supply.     

K-band 3-D MMIC low noise amplifier and mixer using TFMS lines with ground slit

Three-dimensional (3-D) microwave monolithic integrated circuit (MMIC) technology, that incorporates slits in the ground metal, was applied to K-band low noise amplifier (LNA) and I/Q mixer to provide a low cost solution for various K-band receivers such as for P-to-P radio, WLAN, and UWB sensors. The LNA incorporates a quasicoplanar stub in the input-matching network, improving the noise figure by 1 dB. This low-noise amplifier (LNA) exhibits a noise figure of 2.5 dB with an associated gain of 16 dB and an area of 0.75/spl times/0.65 mm/sup 2/. The I/Q resistive mixer incorporates a broadside 3-dB coupler with a 22-/spl mu/m-wide slit in the ground metal beneath the coupled thin-film micro-strip (TFMS) lines (patent pending). The insertion loss of the 3 dB coupler is 0.75 dB. The I/Q mixer exhibits a conversion loss of less than 14 dB at 0.1-2.0GHz IF frequencies for 2-dBm local input power. These LNA and mixer potentially make it easier to integrate receiver functions in a die.     

A 0.7-7 GHz wideband reconfigurable receiver RF front-end in CMOS

In this paper,a 0.7-7 GHz wideband RF receiver front-end SoC is designed using the CMOS process.The front-end is composed of two main blocks:a single-ended wideband low noise amplifier (LNA) and an inphase/quadrature (I/Q) voltage-driven passive mixer with IF amplifiers.Based on a self-biased resistive negative feedback topology,the LNA adopts shunt-peaking inductors and a gate inductor to boost the bandwidth.The passive down-conversion mixer includes two parts:passive switches and IF amplifiers.The measurement results show that the front-end works well at different LO frequencies,and this chip is reconfigurable among 0.7 to 7 GHz by tuning the LO frequency.The measured results under 2.5-GHz LO frequency show that the front-end SoC achieves a maximum conversion gain of 26 dB,a minimum noise figure (NF) of 3.2 dB,with an IF bandwidth of greater than 500 MHz.The chip area is 1.67 × 1.08 mm2.     

A 2.7-V 900-MHz CMOS LNA and mixer

A CMOS low-noise amplifier (LNA) and a mixer for RF front-end applications are described. A current reuse technique is described that increases amplifier transconductance for the LNA and mixer without increasing power dissipation, compared to standard topologies. At 900 MHz, the LNA minimum noise figure (NF) is 1.9 dB, input third-order intercept point (IIP3) is -3.2 dBm and forward gain is 15.6 dB. With a 1-GHz local oscillator (LO) and a 900-MHz RF input, the mixer minimum double sideband noise figure (DSB NF) is 5.8 dB, IIP3 is -4.1 dBm, and power conversion gain is 8.8 dB. The LNA and mixer, respectively, consume 20 mW and 7 mW from a 2.7 V power supply. The active areas of the LNA and mixer are 0.7 mm×0.4 mm and 0.7 mm×0.2 mm, respectively. The prototypes were fabricated in a 0.5-μm CMOS process     

A 24-GHz CMOS front-end

This paper reports the first 24-GHz CMOS front-end in a 0.18-/spl mu/m process. It consists of a low-noise amplifier (LNA) and a mixer and downconverts an RF input at 24 GHz to an IF of 5 GHz. It has a power gain of 27.5 dB and an overall noise figure of 7.7 dB with an input return loss, S/sub 11/ of -21 dB consuming 20 mA from a 1.5-V supply. The LNA achieves a power gain of 15 dB and a noise figure of 6 dB on 16 mA of dc current. The LNA's input stage utilizes a common-gate with resistive feedthrough topology. The performance analysis of this topology predicts the experimental results with good accuracy.     

A 170 MHz RF front-end for ERMES pager applications

A 170 MHz RF front-end for ERMES pager applications has been implemented in a 1.2 μm BiCMOS technology. The chip comprises a low noise amplifier with AGC, a double balanced mixer, a varactor tuned LC local oscillator, and an IF strip containing an AGC amplifier and a double balanced mixer with integrated active output filter. The LNA has a measured gain of 22.3 dB at 170 MHz with a usable AGC range of approximately 20 dB while the conversion transconductance of the mixer is 130 μS. This front-end is suitable for direct conversion and superheterodyne pager receivers, and its noise figure is 6.2 dB. Low power operation has been achieved with the front-end drawing 230 μA at 3 V, which is compatible with the intended application in wrist-watch style pagers     

A 1.2-V RF front-end with on-chip VCO for PCS 1900 direct conversion receiver in 0.13-/spl mu/m CMOS

In this paper, a 1.2-V RF front-end realized for the personal communications services (PCS) direct conversion receiver is presented. The RF front-end comprises a low-noise amplifier (LNA), quadrature mixers, and active RC low-pass filters with gain control. Quadrature local oscillator (LO) signals are generated on chip by a double-frequency voltage-controlled oscillator (VCO) and frequency divider. A current-mode interface between the downconversion mixer output and analog baseband input together with a dynamic matching technique simultaneously improves the mixer linearity, allows the reduction of flicker noise due to the mixer switches, and minimizes the noise contribution of the analog baseband. The dynamic matching technique is employed to suppress the flicker noise of the common-mode feedback (CMFB) circuit utilized at the mixer output, which otherwise would dominate the low-frequency noise of the mixer. Various low-voltage circuit techniques are employed to enhance both the mixer second- and third-order linearity, and to lower the flicker noise. The RF front-end is fabricated in a 0.13-/spl mu/m CMOS process utilizing only standard process options. The RF front-end achieves a voltage gain of 50 dB, noise figure of 3.9 dB when integrated from 100 Hz to 135 kHz, IIP3 of -9 dBm, and at least IIP2 of +30dBm without calibration. The 4-GHz VCO meets the PCS 1900 phase noise specifications and has a phase noise of -132dBc/Hz at 3-MHz offset.     

用于IEEE802．11b／g WLAN直接下变频接收机的射频前端设计

介绍了一种应用于IEEE802．11b／g无线局域网接收机射频前端的设计。基于直接下变频的系统架构。接收机集成了低噪声放大器、I／Q下变频器、去直流偏移滤波器、基带放大器和信道选择滤波器。电路采用TSMC0．18μm CMOS工艺设计,工作在2．4GHz ISM（工业、科学和医疗）频段,实现的低噪声放大器噪声系数为0．84dB,增益为16dB,S11低于-15dB,功耗为13mW;I／Q下变频器电压增益为2dB,输入1dB压缩点为-1 dBm,噪声系数为13dB,功耗低于10mw。整个接收机射频前端仿真得到的噪声系数为3．5dB,IIP3为-8dBm,IP2大于30dBm,电压增益为31dB,功耗为32mW。     

Low-power fully integrated and tunable CMOS RF wireless receiver for ISM band consumer applications

A 0.25-/spl mu/m single-chip CMOS single-conversion tunable low intermediate frequency (IF) receiver operated in the 902-928-MHz industrial, scientific, and medical band is proposed. A new 10.7-MHz IF section that contains a limiting amplifier and a frequency modulated/frequency-shift-key demodulator is designed. The frequency to voltage conversion gain of the demodulator is 15 mV/kHz and the dynamic range of the limiting amplifier is around 80 dB. The sensitivity of the IF section including the demodulator and limiting amplifier is -72 dBm. With on-chip tunable components in the low-power low-noise amplifier (LNA) and LC-tank voltage-controlled oscillator circuit, the receiver measures an RF gain of 15 dB at 915 MHz, a sensitivity of -80 dBm at 0.1% bit-error rate, an input referred third-order intercept point of -9 dBm, and a noise figure of 5 dB with a current consumption of 33 mA and a 2450 /spl mu/m/spl times/ 2450 /spl mu/m chip area.     

A 2.4 GHz CMOS sub-sampling mixer with integrated filtering

A sub-sampling mixer that incorporates sampling switches and hold capacitors into the parallel resonant LC load of an LNA is proposed. The noise figure of the proposed sub-sampling mixer is lower than that of a standard sampling circuit because the proposed mixer has narrow-band gain and input noise filtering properties. A novel level-shifting clock buffer with fast rise and fall times to drive the mixer sampling switches is presented. The mixer was fabricated in a 0.18 /spl mu/m CMOS process and measured results are presented for an RF input frequency of 2.42 GHz and a sampling frequency of 100 MHz. With a measured noise figure of 21.8 dB, the proposed circuit shows improved performance compared to other published sub-sampling mixers.     

A CMOS passive mixer with low flicker noise for low-power direct-conversion receiver

A CMOS passive mixer is designed to mitigate the critical flicker noise problem that is frequently encountered in constituting direct-conversion receivers. With a unique single-balanced passive mixer design, the resulted direct-conversion receiver achieves an ultralow flicker-noise corner of 45 kHz, with 6 dB more gain and much lower power and area consumption than the double-balanced counterpart. CMOS switches with a unique bias-shifting network to track the LO DC offset are devised to reduce the second-order intermodulation. Consequently, the mixer's IIP2 has been greatly enhanced by almost 21 dB from a traditional single-balanced passive mixer. An insertion compensation method is also implemented for effective dc offset cancellation. Fabricated in 0.18 /spl mu/m CMOS and measured at 5 GHz, this passive mixer obtains 3 dB conversion gain, 39 dBm IIP2, and 5 dBm IIP3 with LO driving at 0 dBm. When the proposed mixer is integrated in a direct-conversion receiver, the receiver achieves 29 dB overall gain and 5.3 dB noise figure.     

A dual-b and RF front-end of direct conversion receiver for wireless CDMA cellular phones with GPS capability

A highly integrated direct conversion receiver for cellular code division multiple access (CDMA) and GPS applications is successfully developed using a 0.5-/spl mu/m SiGe BiCMOS technology. The receiver consists of two low-noise amplifiers (LNAs), a dual-band mixer, two voltage-controlled oscillators (VCOs), a local-oscillator signal generation block, and channel filters. The CDMA LNA achieves a noise figure of 1.3 dB, an input-referred third-order intercept point (IIP3) of 10.9 dBm, and a gain of 15.3 dB with a current consumption of 9.8 mA in the high-gain mode. The mixer for the CDMA mode achieves an uncalibrated input-referred second-order intercept point of 53.7 dBm, an IIP3 of 6.4 dBm, a noise figure of 7.2 dB and a voltage gain of 37.2 dB. The phase noise of the CDMA VCO is approximately -133 dBc/Hz at a 900-kHz offset from a 1.762-GHz operating frequency. It exceeds all the CDMA requirements when tested on a handset.     

A 60-GHz CMOS receiver front-end

The unlicensed band around 60 GHz can be utilized for wireless communications at data rates of several gigabits per second. This paper describes a receiver front-end that incorporates a folded microstrip geometry to create resonance at 60 GHz in a common-gate LNA and active mixers. Realized in 0.13-/spl mu/m CMOS technology, the receiver front-end provides a voltage gain of 28 dB with a noise figure of 12.5 dB while consuming 9 mW from a 1.2-V supply.     

Low-voltage 1.9-GHz front-end receiver in 0.5-μm CMOS technology

This paper describes the design of a 1.9-GHz front-end receiver. The target application of the receiver is the personal communications standard PCS1900. Powered by a 1-V supply, the receiver consists of a low noise amplifier (LNA) and a downconversion mixer. The receiver was fabricated within a 0.5-μm CMOS technology. The LNA features 15 dB of gain and a 1.8-dB noise figure. The mixer exhibits 1.5-dB conversion loss, 12-dB noise figure, and 0 dBm 1 dB-compression point     

Design and optimization of a 2.4 GHz RF front-end with an on-chip balun

A 2.4 GHz low-power,low-noise and highly linear receiver front-end with a low noise amplifier(LNA) and balun optimization is presented.Direct conversion architecture is employed for this front-end.The on-chip balun is designed for single-to-differential conversion between the LNA and the down-conversion mixer,and is optimized for the best noise performance of the front-end.The circuit is implemented with 0.35μm SiGe BiCMOS technology.The front-end has three gain steps for maximization of the input dynamic range.The overall maximum gain is about 36 dB.The double-sideband noise figure is 3.8 dB in high gain mode and the input referred third-order intercept point is 12.5 dBm in low gain mode.The down-conversion mixer has a tunable parallel R-C load at the output and an emitter follower is used as the output stage for testing purposes.The total front-end dissipation is 33 mW under a 2.85 V supply and occupies a 0.66 mm~2 die size.     

Design of a High Performance 2-GHz Direct-Conversion Front-End With a Single-Ended RF Input in 0.13 $mu$m CMOS

A 2.1 GHz CMOS front-end with a single-ended low-noise amplifier (LNA) and a double balanced, current-driven passive mixer is presented. The LNA drives an on-chip transformer load that performs single-ended to differential conversion. A detailed comparison in gain, noise, and second and third order linearity performance is presented to motivate the choice of a current-driven passive mixer over an active mixer. The front-end prototype was implemented on a 0.13 $mu$m CMOS process and occupies an active chip area of 1.1 mm $^{2}$. It achieves 30 dB conversion gain, a low noise figure of 3.1 dB (integrated from 40 KHz to 1.92 MHz), an in-band IIP3 of ${-}$12 dBm, and IIP2 better than 39 dBm, while consuming only 12 mW from a 1.5 V power supply.      

A single-chip GaAs MMIC image-rejection front-end for digitalEuropean cordless telecommunications

An active image-rejection filter is presented in this paper, which applies actively coupled passive resonators. The filter has very low noise and high insertion gain, which may eliminate the use of a low-noise amplifier (LNA) in front-end applications. The GaAs monolithic-microwave integrated-circuit (MMIC) chip area is 3.3 mm² . The filter has 12-dB insertion gain, 45-dB image rejection, 6.2-dB noise figure, and dissipates 4.3 mA from a 3-V supply. An MMIC mixer is also presented. The mixer applies two single-gate MESFETs on a 2.2-mm² GaAs substrate. The mixer has 2.5-dB conversion gain and better than 8-dB single-sideband (SSB) noise figure with a current dissipation of 3.5 mA applying a single 5-V supply. The mixer exhibits very good local oscillator (LO)/RF and LO/IF isolation of better than 30 and 17 dB, respectively, Finally, the entire front-end, including the LNA, image rejection filter, and mixer functions is realized on a 5.7-mm ² GaAs substrate. The front-end has a conversion gain of 15 dB and an image rejection of more than 53 dB with 0-dBm LO power. The SSB noise figure is better than 6.4 dB, The total power dissipation of the front-end is 33 mW. The MMIC's are applicable as a single-block LNA and image-rejection filter, mixer, and single-block front-end in digital European cordless telecommunications. With minor modifications, the MMIC's can be applied in other wireless communication systems working around 2 GHz, e.g., GSM-1800 and GSM-1900     

An 800-MHz–6-GHz Software-Defined Wireless Receiver in 90-nm CMOS

A software-defined radio receiver is designed from a low-power ADC perspective, exploiting programmability of windowed integration sampler and clock-programmable discrete-time analog filters. To cover the major frequency bands in use today, a wideband RF front-end, including the low-noise amplifier (LNA) and a wide tuning-range synthesizer, spanning over 800 MHz to 6 GHz is designed. The wideband LNA provides 18-20 dB of maximum gain and 3-3.5 dB of noise figure over 800 MHz to 6 GHz. A low 1/f noise and high-linearity mixer is designed which utilizes the passive mixer core properties and provides around +70 dBm IIP2 over the bandwidth of operation. The entire receiver circuits are implemented in 90-nm CMOS technology. Programmability of the receiver is tested for GSM and 802.11g standards