共查询到20条相似文献,搜索用时 250 毫秒
1.
2.
试述Fe在Al-Mg-Si系铝合金中的行为 总被引:1,自引:0,他引:1
一、序言 Al-Mg-Si系铝合金中主要是6061和6063合金,用途最广的是6063铝合金。众所周知,6063铝合金是中等强度合金,且易于加工成型,广泛用于建筑装饰行业。其生产过程包括熔炼、铸造、挤压和阳极氧化着色,合金中Fe成为附属组元是不可避免的。研究Fe在Al-Mg-Si系铝合金生产过程中的行为是很有必要的,这样有益于改善该系合金加工性能和型材产品质量。二、Fe的来源 Al-Mg-Si合金中的Mg、Si含量是该合 相似文献
3.
作者概述了以6063合金为代表的Al—Mg—Si系铝合金型材的生产工艺过程,从理论上分析了6063合金型材生产过程中的各个工艺参数对形成型材表面暗斑的影响趋势,提出了各工艺参数的控制范围。 相似文献
4.
《有色金属材料与工程》2020,(3)
以6063铝合金汽车吸能型材为研究对象,采用准静态轴向加载方式,从组织、力学性能等方面研究不同时效制度对6063铝合金型材准静态压缩性能的影响。结果表明:当时效温度为200℃时,随着时效时间的延长,合金组织中大尺寸析出相的数量呈先增加后减少的趋势,粗晶层厚度基本不变;随着时效时间的延长,6063铝合金型材的强度、硬度升高,同时准静态压缩的承载能力增强,时效时间6 h时承载能力达到峰值;6063铝合金型材的吸能性能随时效时间的延长而提高,时效时间6 h的吸收功较2 h的提高了48%。 相似文献
5.
6005T5铝合金天线管型材生产工艺研究 总被引:1,自引:0,他引:1
6005铝合金属于A l-M g-Si系热处理可强化变形铝合金,该合金具有优良的挤压性、耐腐蚀性、良好的加工性以及中等强度,因而得到广泛的应用,主要用于要求强度大于6063铝合金强度的结构件,如梯子、电视天线等。6005T5铝合金天线管型材为四筋有缝管材,由于其系列产品的各种规格之间需要进行伸缩配合,因此对产品质量要求较为严格:①由于该合金合金化程度相对较低,需合理控制主要强化元素M g、Si比例,才能保证天线管型材具有一定的强度;②需严格控制挤压工艺以及在线淬火风冷强度,以保证型材的状态及最终性能;③由于天线管型材是由可伸缩的多节… 相似文献
6.
《铝加工》2021,(2)
正近日,山东南山铝业股份有限公司成功生产出稀土铝合金6063A管材,标志着公司自主试制稀土铝合金管材取得突破性进展。6063A合金是南山铝业公司在原6063合金研制的基础上,根据客户要求而研制的新型合金牌号,具有合金含量要求高、合金化程度高、挤压技术高等优点,同时还具有合金含量控制难度大、铸造难度大、挤压裂纹倾向性大等特点和难点。6063铝合金是一种较常用的变形合金,多用于工业和民用建筑,在该合金熔炼过程中加入微量的稀土元素就形成了新型稀土铝合金材料,比原合金材料抗拉强度提高24%、挤压速度提高0.5倍、成材率提高3%,并改善了其表面质量,增加了其耐蚀性和着色性。 相似文献
7.
研究了6063合金中的微量Si、Mg元素对Al-Ti-C中间合金细化效果的影响,并探讨了其影响机理。试验结果表明,当6063铝合金中同时存在微量的Si、Mg元素时,Al-Ti-C的细化效果会更加显著。 相似文献
8.
6063铝棒质量提高的措施探讨 总被引:1,自引:0,他引:1
6063合金棒属Al—Mg—Si系合金,本文通过介绍Al—Mg—Si系合金的基本特点、合金元素以及熔炼过程中工艺控制,并对其进行探讨分析,提出了6063铝合金棒质量提高的措施。 相似文献
9.
10.
浅析了铸锭质量、挤压质量对6063型材磨砂质量的影响,从溶铸、挤压方面探讨了提高磨砂面型材表面质量的途径. 相似文献
11.
12.
13.
Alan A. Luo Robert C. Kubic John M. Tartaglia 《Metallurgical and Materials Transactions A》2003,34(11):2549-2557
This study investigated the microstructure and fatigue properties of hydroformed sections of the 5754 and 6063 aluminum alloys.
The second-phase particles in 6063-T7 are identified as a mixture of Al12Fe3Si and Al9Fe2Si2, with a slightly higher fraction of the former. The constituent particles in the 5754 alloy are Al4Mn-type hexagonal compounds, where Mn is partially substituted by various other elements, resulting in Al4(Fe,Mn,Si,Cr). The results show that despite its lower yield strength, the hydroformed 5754 alloy has higher ultimate tensile
strength, ductility, and, more importantly, higher fatigue resistance than the 6063 material. Both crystallographic stage
I and noncrystallographic stage II cracking are found in the 6063-T7 samples, but only stage II cracking is observed in the
5754 alloy. This implies that the low fatigue strength of 6063-T7 is related to its relatively large grain size, resulting
in rapid stage I crack propagation. The higher fatigue lives of the 5754 alloy compared to the 6063 alloy in both the low-
and high-cycle life regimes are due to the increased fatigue-crack-initiation and propagation resistance of the 5754 alloy
and its probable cyclic strain-hardening behavior. 相似文献
14.
分析铝合金淬火性能,确认风淬火方式无法满足产品的技术要求。本结合我厂实际情况提出了在线水淬火装置技改方案,并进行了技术和经济分析与探讨。 相似文献
15.
挤压铸锭的质量对铝型材的质量有着举足轻重的影响,高质量的挤压铸锭是获得高质量铝型材的基础。本文分别从铝型材的化学元素成分控制、熔体质量、铸造的工艺参数、铸锭的均匀化处理等方面探讨了提高6063铝合金挤压铸锭质量的技术途径。 相似文献
16.
17.
18.
阐述了6063铝合金“中心裂纹”铸锭对铝型材表面质量的不良影响,其次,分析了裂纹的形成机理及其影响因素,提出了具体的解决方案。 相似文献
19.
The microstructure and mechanical properties of the ultra-fine grained (UFG) Al6063 alloy reinforced with nanometric aluminum
oxide nanoparticles (25 nm) were investigated and compared with the coarse-grained (CG) Al6063 alloy (~2 μm). The UFG materials were prepared by mechanical alloying (MA) under high-purity Ar and Ar-5 vol pct O2 atmospheres followed by hot powder extrusion (HPE). The CG alloy was produced by HPE of the gas-atomized Al6063 powder without
applying MA. Electron backscatter diffraction under scanning electron microscopy together with transmission electron microscopy
studies revealed that the microstructure of the milled powders after HPE consisted of ultra-fine grains (>100 nm) surrounded
by nanostructured grains (<100 nm), revealing the formation of a bimodal grain structure. The grain size distribution was
in the range of 20 to 850 nm with an average of 360 and 300 nm for Ar and Ar-5 pct O2 atmospheres, respectively. The amount of oxide particles formed by reactive mechanical alloying under the Ar/O2 atmosphere was ~0.8 vol pct, whereas the particles were almost uniformly distributed throughout the aluminum matrix. The
UFG materials exhibited significant improvement in the hardness and yield strength with an absence of strain hardening behavior
compared with CG material. The fracture surfaces showed a ductile fracture mode for both CG and UFG Al6063, in which the dimple
size was related to the grain structure. A mixture of ductile–brittle fracture mode was observed for the UFG alloy containing
0.8 vol pct Al2O3 particles. The tensile behavior was described based on the formation of nonequilibrium grain boundaries with high internal
stress and dislocation-based models. 相似文献
20.
为了研究连退板表层元素富集行为及相互作用,借助扫描电镜、辉光放电光谱仪、光电子能谱仪和透射电镜等技术手段对铝镇静钢和双相钢连退板表层中的富集元素进行了详细地表征与分析。结果表明,铝镇静钢连退板表面的主要富集元素有O、Mn和Al;而双相钢连退板表面的主要富集元素有O、Mn和Si。沿着浅表层深度分析可知,对于合金元素含量较高的双相钢,沿浅表层富集更深,富集深度约为50 nm;而合金元素含量较低的铝镇静钢,富集深度仅约为25 nm。综合分析不难发现,相对于铝镇静钢,双相钢添加了Si元素以后在其表面优先富集Si元素并同时形成了Si的氧化物,从而导致Al元素的富集及氧化物的形成受到了抑制。 相似文献