常化后冷却工艺对1600MPa级超高强钢组织性能的影响

为改善高强度钢的塑性和韧性,对中碳低合金马氏体高强度钢分别采用常化后空冷＋回火和常化后控冷＋回火工艺,研究常化后冷却工艺对钢中残余奥氏体及力学性能的影响.采用扫描电镜获得钢的组织形态,利用X射线衍射和电子背散射衍射技术分析钢中残余奥氏体的体积分数、形貌和分布.发现两种工艺下均得到板条马氏体＋残余奥氏体组织,残余奥氏体均匀分布在板条之间,随工艺参数不同,其体积分数在3%~10%变化.常化后加速冷却能显著细化马氏体板条,提高钢的屈服强度和抗拉强度100 MPa以上,冲击功下降4 J.残余奥氏体的体积分数随常化控冷终冷温度的升高呈现先升高后降低的变化,常化后的控制冷却也可以作为进一步改善马氏体类型钢组织和性能的方法      

回火温度对COST-FB2转子钢析出相与力学性能的影响

 为了调整COST-FB2转子钢的强韧性,采用OM、SEM和TEM等手段研究了回火温度对COST-FB2转子钢的析出相类型与力学性能的影响。结果表明,随着回火温度由350 ℃升高到750 ℃,试验钢的强度、硬度不断下降,塑性和冲击功上升;试验钢350 ℃和570 ℃回火后的高强低韧性可通过再次在700 ℃回火改善。淬火后COST-FB2转子钢中的残余奥氏体,可通过在570 ℃回火消除;在350 ℃和570 ℃回火后马氏体板条内部有大量针状的M₃C,700 ℃回火后的显微组织中M₃C消失,M₂₃C₆在原奥氏体晶界和马氏体板条界上析出,750 ℃回火后晶界上的M₂₃C₆有聚集粗化的现象,部分马氏体板条存在回复现象。     

Effect of Heat Treatment on Microstructure and Mechanical Properties of HB400 Grade High Strength Abrasion Resistant Steel

High strength abrasion resistant steel plates are widely used in mining,construction and agricultural machineries.The plates are,however,usually poor in impact toughness.An attempt is made to improve the impact toughness of HB400 grade abrasion resistant steel by controlling quenching and tempering of the plates.Optimized combination of the strength and the toughness has been achieved by choosing best fit set of quenching and tempering condition.Mechanism underlying the achievement has been investigated in terms of the microstructure consisting of tempered lath martensite,retained austenite and precipitated carbides.     

新型低合金高强韧性耐磨钢的研究

采用多元合金化及变质处理设计了一种新型低合金高强度高韧性耐磨钢。研究了钢的基本特性、显微组织、断口形貌以及热处理工艺对钢的力学性能和耐磨性的影响。研究结果表明,该钢的过冷奥氏体的稳定性高,具有高淬透性及高回火稳定性,经８８０～９２０℃淬火及２５０～３００℃回火后获得回火板条马氏体组织,使钢具有高强韧性及高耐磨性     

Investigation on microstructure and properties of a combined precipitation hardening ultrahigh strength steel

The microstructure and properties of a combined precipitation hardening ultrahigh strength steel with nano-sized carbides and intermetallics were studied systematically.The results show that after tempering at 300℃lots ofε-carbides are precipitated in the martensite,the strength rises and the toughness falls slightly.After tempering at 430℃,much coarser cementite lamina are precipitated in martensitic laths,which causes the impact toughness falls to the minimum value.With temperature further increasing the cementites are dissolved and M₂C carbides,β-NiAl intermetallics and reverse austenite begin to precipitate.The tensile strength and yield strength achieve the peak value at 470℃,490℃respectively.The tested steel achieve a tensile strength of 2 120 MPa,a yield strength of 1 950 MPa and impact energy of 54 J/cm² after optimum tempering at 510℃.When tempering temperature is above 530℃the M₂C carbides and reverse austenite is coarsening.After tempering at 560℃the reverse austenite reaches the maximum volume fraction in present work.     

调质低碳贝氏体钢的组织和性能

研究了C-Mn-Mo-Cu-Nb-Ti-B系低碳微合金钢915℃淬火和490~640℃回火的调质工艺对钢的组织及力学性能的影响.用扫描电镜和透射电镜对实验钢的组织、析出物形态和分布以及断口形貌进行观察,采用X射线衍射仪分析钢中残余奥氏体的体积分数.结果表明:调质后,实验钢获得贝氏体、少量马氏体及残余奥氏体复相组织,贝氏体板条宽度只有250 nm,残余奥氏体的体积分数随着回火温度的升高而降低,经淬火与520℃回火后残余奥氏体的体积分数为2.1%.调质后析出物的数量激增,6~15 nm的析出物占70%以上.实验钢经过915℃淬火与520℃回火后,其屈服强度达到915 MPa,抗拉强度990 MPa,-40℃冲击功为95 J.细小的析出物及窄的板条提高了钢的强度.板条间有残余奥氏体存在,改善了实验钢的韧性.      

The stability of precipitated austenite and the toughness of 9Ni steel

A correlation was confirmed between the good low temperature Charpy toughness of 9Ni steel and the stability of its precipitated austenite against the martensitic transformation. Changes in the microstructure during isothermal tempering were studied in detail. The austenite/martensite interface is originally quite coherent over ∼100 A distances. With further tempering, however, the dislocation structure at the austenite/martensite interface changes, and this change may be related to the increased instability of the austenite particles. The reduction in austenite carbon concentration does not seem large enough to account for the large reduction in austenite stability with tempering time. The strains inherent to the transformation of austenite particles create dislocation structures in the tempered martensite. The large deterioration of the Charpy toughness of overtempered material is attributed, in part, to these dislocation structures.     

深冷处理对NM500耐磨钢性能与磨损行为的影响

以一种自行设计的NM500级别耐磨钢为研究对象,利用冲击磨损试验,分析了深冷处理对其组织性能和磨损行为的影响。结果表明,NM500耐磨钢经深冷处理后,抗拉强度、硬度和冲击韧性均有提高,在淬火+深冷+回火处理后,最佳的综合力学性能可达抗拉强度1 910 MPa、硬度523HB、冲击韧性24.3 J/cm2,此时试验钢组织主要为马氏体,有Nb和Ti的碳化物析出。深冷处理通过残余奥氏体向马氏体转变,减少了不稳定相的含量,提升了试验钢的力学性能,从而使淬火+深冷+回火处理后的试验钢具有更高的耐磨性,此时的磨损机制以磨粒磨损为主,磨损形貌主要为犁沟、犁皱。而未经深冷处理的淬火+回火处理试验钢磨损机制以黏着磨损为主,磨损形貌主要为剥落坑和切削。     

非调质状态下HG80钢的组织和性能研究

研究了热轧态,回火态及不同冷却速度下ＨＧ８０钢的显微组织及力学性能,并讨论了ＨＧ８０钢在非调质状态下的强韧化机制。结果表明,ＨＧ８０钢非调质状态下的组织由铁素体基体和孪晶马氏体／残余奥氏体岛状相所组成;熟轧态主要是粒状组织,韧性偏低;随轧后冷却速度的提高,粒状贝氏体量增加,组织细化,钢的强性改善。     

Cr含量对G18CrMo2-6钢组织和性能的影响

通过热处理试验、微观组织表征和力学性能检测,对比研究了在不同Cr含量的情况下,G18CrMo2-6钢微观组织形貌、力学性能的变化.结果表明,随着合金元素Cr含量增加,同一温度退火热处理后G18CrMo2-6钢中铁素体体积分数减少,贝氏体增多,从而导致材料强度升高;但是Cr含量的增加还会导致该类材料退火产生的贝氏体中马氏...     

70Si3MnCrMo钢中贝氏体及其回火稳定性

 对一种新型70Si3MnCrMo钢进行了等温和连续冷却贝氏体相变热处理。利用拉伸和冲击试验研究试验钢的力学行为,利用XRD、SEM和TEM等方法对试验钢进行了相组成分析和微观组织形貌观察。研究结果表明,试验钢经等温贝氏体相变,其最佳综合力学性能出现在200 ℃回火,强塑积为26.4 GPa·%。经连续冷却贝氏体相变,其最佳综合力学性能出现在300 ℃回火,强塑积达到28.6 GPa·%。回火温度较低的情况下,热处理后的组织为由贝氏体铁素体和残余奥氏体组成的无碳化物贝氏体组织,这种无碳化物贝氏体由超细贝氏体铁素体板条而获得超高强度,由一定量的高碳残余奥氏体来保证较高的塑性和韧性。试验钢经连续冷却贝氏体相变,其贝氏体铁素体板条中出现了超细亚单元,并且残余奥氏体呈薄膜状和小块状两种形态分布于贝氏体铁素体板条之间,这两种形态残余奥氏体的稳定性不同。拉伸试样在变形过程中残余奥氏体持续发生TRIP效应,直至全部残余奥氏体都发生转变生成应变诱发马氏体,从而使钢得到更好的强、塑性配合,表现出十分优异的综合性能。     

淬火工艺对马氏体高强钢组织和性能的影响

摘要：采用拉伸、冲击、金相、电子背散射衍射、透射电镜、X射线衍射等试验手段,研究了在线直接淬火+回火（DQT）与离线再加热淬火+回火（RQT）工艺对马氏体高强钢组织性能的影响。结果表明,2种试验钢组织均为板条马氏体,RQT试验钢原奥氏体晶粒及板条束呈等轴状,板条块较短,板条较宽,DQT试验钢原奥氏体晶粒呈扁平状,板条束贯穿整个晶粒,板条块呈细长状,板条宽度较小;位错强化是DQT试验钢强度较RQT高的主要原因;板条束为控制DQT和RQT试验钢韧性的最小单元;DQT试验钢大角晶界比例较低,其具有较大的马氏体板条束尺寸以及更高的位错密度,断裂应力较低,低温韧性较差。     

HB450低合金超高强耐磨钢回火过程中的组织性能演变

  利用透射电镜（TEM）、扫描电镜（SEM）等试验方法,研究了新型低成本HB450低合金超高强耐磨钢在不同回火条件下组织和性能演变规律,并分析了其强韧变化机制。结果表明：回火对试验钢的硬度和强度均有较大影响。在200~250℃回火,试验钢表现出良好的强韧性配合,满足国标工程机械用高强度耐磨板GB/T24186—2009中NM450级别要求;在250℃回火时,试验钢出现硬化迹象。透射电镜分析表明,在该温度下回火,析出物中除了有大量弥散分布的ε 碳化物外,还出现了少量30~50nm的（Nb,Ti）（C,N）粒子,该2类粒子对试验钢的强化起着较大的作用。     

HB400级高强度准贝氏体耐磨钢板的组织与性能

研究了热轧、低温回火和热轧、正火、低温回火及轧态不同温度回火工艺对新型HB400级高强度准贝氏体耐磨钢板的组织和力学性能及耐磨性能的影响。结果表明，2种状态下耐磨板的组织由贝氏体铁索体(BF)和残余奥氏体(AR)组成，具有良好的强韧性及耐磨性能。低温回火可以改善耐磨钢板的韧性。新型耐磨钢板具有较强的回火抗力。用准贝氏体钢生产高强度耐磨板具有生产工艺简单，成本低廉等特点。     

Banded Microstructure Formation and Its Effect on the Performance of 06Ni9 Steel

Focusing on the banded microstructure formed during the production of 06Ni9 steels for cryo-LNG,this paper examines its formation,distribution of alloying elements,structure,hardness,and low-temperature property.The results show that the banded microstructure formed after hot-rolling and cooling of the steel binct in which the element segregation occurred during solidification.The phase change during heat treatment also can cause the formation of the banded microstructure of 06Ni9 steel.The white bands are mainly composed of ferrite and reversed austenite,and the black bands are mainly composed of reversed austenite and a certain amount of ferrite.Element segregation and formation of more carbide caused some black regions to appear.Grain refinement of 06Ni9steel is beneficial to the formation of reversed austenite,the redistribution of alloying elements,improving the stability of austenite and the low-temperature toughness of steel.This steel easily undergoes nickel segregation;thus,undergoing a secondary quenching and tempering process is recommended.The refinement of martensite quenching above A c3,the martensite that is rich in nickel and carbon,residual austenite and a few little of ferrite after secondary quenching lower than A c3 are beneficial to the formation of high stability austenite.Thus,this can meet the strength and toughness requirement of the low temperature 06Ni9 steel.     

高强韧性海洋平台用E550钢板生产工艺研究

介绍了E550钢板的主要生产工艺和技术难点,通过理论分析设计了E550的成分体系,采用Thermal-Calc和经验公式,获得了其热力学相图和相变点温度等热力学数据。根据E550的热力学特性,设计了两阶段轧制工艺,精轧的终轧温度控制在再结晶温度附近,利用奥氏体再结晶充分细化晶粒。淬火奥氏体化温度选择为920℃,回火温度设计为630℃,利用碳化物的析出强化效果和缺陷密度变化的位错强化获得良好的强韧性匹配。50 mm厚钢板的淬火态1/4厚度处的微观组织为马氏体,中心的组织为马氏体和少量贝氏体的混合物。回火热处理后,马氏体板条界面减少,碳化物在马氏体板条界面析出,钢板1/4到中心的组织均匀化。30和50 mm厚E550钢板的力学性能达到了船级社标准要求,并有较大的富裕量。热输入能量为15和50 kJ/cm焊接后,钢板具有良好的强度性能,熔合线和热影响区的冲击功较高。     

Transmission electron microscopy examination of hardening and toughening phenomena in Aermet 100

The effect of tempering on the microstructure and mechanical properties of ultrahigh strength Aermet 100 steel was examined. In the as-quenched condition, the steel contained a dispersion of relatively fine, undissolved, (CrTiFeMo)C and (CrFeMo)₂₃C₆ carbides in a martensitic matrix. Upon tempering at 427 °C, the martensite decomposed to form a high density of cementite particles concomitant with a significant drop in toughness. Tempering at 454 °C resulted in peak strength (yield strength ∼ 1756 MPa) due to the precipitation of coherent zones of fine carbides. The peak in toughness (170 MPa√m), attained at a tempering temperature of 482 °C, was attributed to both the absence of cementite and the formation of reverted, stable austenite. Tempering at higher temperatures resulted in loss of both strength and toughness, which was suggested to be the result of precipitate coarsening and formation of unstable austenite, respectively. The details of the electron microscopy studies and mechanism of strengthening and toughening are discussed in light of the current understanding of this subject.     

回火温度对9Ni钢低温韧度的影响研究

为了研究不同回火温度对9Ni钢低温韧度的影响,利用OM、SEM、TEM对试验钢微观组织和断口形貌进行观察分析,研究表明:在550~600℃范围内回火,9Ni钢强度和韧度达到最佳匹配,且其他各项性能也达到最佳;回转奥氏体、碳化物及回转奥氏体诱发马氏体相变等均对低温韧度产生重要影响。     

调质热处理对55NiCrMoV7模具钢组织与力学性能的影响

采用扫描电镜(SEM)、硬度测试、V型冲击实验和单向拉伸实验结合有限元建模仿真,研究了55NiCrMoV7模具钢在不同淬火温度(790～910℃)、回火温度(100～650 ℃)下的微观组织演化和力学性能的变化规律。结果表明,随着淬火温度升高,球状碳化物逐渐溶解到马氏体基体中,马氏体组织不断长大、粗化,残余奥氏体逐渐增多;淬火后HRC硬度值基本稳定在42～46,屈服强度和抗拉强度先增大后减小,870 ℃淬火后均达到最大值1 380 MPa和1485 MPa,冲击韧性在850 ℃淬火后最大,为26 J。在不同温度回火过程中,马氏体组织含量基本稳定,随着回火温度继续升高,残余奥氏体逐渐溶解,碳化物从马氏体边界处析出,细小而弥散。870 ℃ 4 h淬火+560 ℃ 6 h回火可以使55NiCrMoV7钢具有良好的综合力学性能。     

钢铁结构材料的组织细化

采用组织超细化提高钢铁结构材料的强细性和使用寿命是上个世纪90年代中期以来的发展趋势。介绍了我国973第一批项目之一“新一代钢铁材料重大基础研究”的主要5种超细化方法，适用于不同强度和显微组织的钢类：具有铁素体 珠光体(F P)的碳素或低合金钢，采用强力轧制和形变诱导铁素体相交(DIFT)技术；在薄板坯连铸连轧现代流程下，采用第二相(析出相)的纳米化控制；具有低碳贝氏体或针状铁素体的微合金钢采用形变诱导析出(DIP)和中温相交控制；采用调质处理的合金结构钢，应用新的合金设计思路以提高界面温度，增加氢陷阱和二次硬化路线，快速超细晶热处理的综合技术；发展无碳化物贝／马组织和富碳残奥薄膜以做到中低温回火合结钢的强韧化优良配合。