Synthesis and Luminescence Properties of Gd2O3：Eu^3＋ Phosphors

Gd2O3: Eu^3 phosphors were prepared by urea homogeneous precipitation with different surfactant and sol-gel method. XRD patterns show that all the obtained samples are in cubic Gd2O3, and the results of FTIR and fluorescent spectra conformed that OP is a good surfactant for preparing the Gd2O3:Eu^3 phosphors. The SEM photographs show that the particles prepared by urea homogeneous precipitation method are all spherical and well-dispersed, and grain morphology can be controlled by different surfactant. XRD and SEM indicate that the particle sizes prepared by sol-gel method are in the range of 5-30 nm, and the grain sizes increase with increasing of heated temperatures. Luminescence spectra indicat that the main emission peaks of all samples are at 610 nm, the intensities are different from samples prepared with different surfactant and the luminescence intensities increase with increasing of annealed temperatures.     

Optical Spectroscopy of Er^3＋ and Er^3＋/Yb^3＋ Co-doped Bi2O3-GeO2-B2O3-ZnO Glasses

The （60 - x）Bi2O3 - xGeO2-30B2O3-10ZnO （x = 5, 10, 20, 30 molar percent） glasses doped with Er^3＋ and Er^3＋/Yb^3＋ were fabricated using the melting method. The thermal stability of the glasses was studied with their DTA curves. The results show that the difference between the glass transition temperature and the crystallization onset temperature increases with the increase of GeO2 content, indicating that the thermal stability of the glass has become better. The absorption spectra were recorded and the stimulated emission cross sections were calculated using the McCumber theory. The Ω2, O4, and Ω6 parameters,the transition probability, the radiative lifetime, and the fluorescence branch ratio of Er^3＋ for optical transition were calculated from their absorption spectra in terms of reduced matrix U^（t）（λ = 2, 4, 6） character for optical transitions. The infrared emission of Er^3＋ was measured upon excitation with 970 nm light and the full width at half-maximum （FWHM） was estimated from the emission spectra. The pumping efficiency and the intensity of the emission at the 1.54 μm band of Er^3＋ were enhanced considerably by co-doping Yb^3＋ .     

Photoluminescence properties of M2ZnSi2O7:Eu2+（M=Sr,Ba）

The hardystonite phosphors of Eu2+ activated M2ZnSi2O7(M=Sr,Ba) were synthesized by combustion-assisted method.They were systematically characterized by photoluminescence excitation and emission spectra.The emission spectra of these two phosphors showed that the main emission peaks are at 475 and 503 nm due to 4f65d1→4f7 transition of Eu2+.Both phosphors could be efficiently excited in the wavelength range of 250-425 nm where the near ultraviolet light-emitting diode was well matched.The(x,y) color coordinates were determined with the emission values(x,y)=(0.41,0.21) and(0.16,0.45) for the M2ZnSi2O7:Eu2+(M=Sr,Ba) phosphors.     

Luminescent Properties of Green Phosphor Ca8Mg（SiO4 ）4 Cl2：EU^2＋ , DY^3＋ for LED Applications

The new phosphor calcium magnesium chlorosilicate, codoped with Eu^2＋ and Dy^3＋, was synthesized with the help of the high temperature solid state reaction in reducing atmosphere. The excitation and emission spectra were very similar to that of Ca8Mg（SiO4）4Cl2 ：Eu^2＋, and the Dy^3＋ concentration influenced the emission intensity of this phosphor. The intensity of Eu^2＋ and Dy^3＋ codoped CMSC was stronger than that of Eu^2＋ singly doped CMSC. The emission spectrum of the Dy^3＋ ion overlapped the absorption band of the Eu^2＋ ion, indicating that an energy transfer from Dy^3＋ to Eu^2＋ took place in CMSC：Eu^2＋, Dy^3＋ phosphor. The mechanism of the energy transfer from Dy^3＋ tO Eu^2＋, in this phosphor, might be resonant energy transfer.     

Sol-gel processed Ce^3＋, Tb^3＋ codoped white emitting phosphors in Sr2Al2SiO7

Sr2Al2SiO7：Ce^3＋, Tb^3＋ white emitting phosphors were fabricated using the sol-gel method. X-Ray Powder Diffraction （XRD） analysis confirmed the formation of Sr2Al2SiO7：Ce^3＋, Tb^3＋. Scanning Electron Microscopy （SEM） observation indicated that the microstructure of the phosphor consisted of regular fine grains with an average size of about 0.5-1 μm. Luminescence properties were analyzed by measuring the photoluminescence spectra. The Ce^3＋, Tb^3＋-codoped Sr2Al2SiO7 phosphors showed four main emission peaks： one at 414 nm for Ce^3＋ and three at 482, 543, and 588 nm for Tb^3＋. The emission spectra of the samples with different doping concentrations showed that the Tb^3＋ emission was dominant because of the persistent energy transfer from Ce^3＋. The decay characteristic was better than that prepared by the solid-state process in the comparable condition. The codoped phosphor displayed long persistent white phosphorescence.     

Preparation and Long Persistence Red Luminescence of M0.2Ca0.8TiO3 ： Pr^3＋ （M = Mg^2＋ , Sr^2＋ , Ba^2＋ , Zn^2＋）

M0.2Ca0.8TiO3 : Pr^3 (M = Mg^2 , Sr^2 , Ba^2 , Zn^2 ) long persistence red phosphors were prepared by solid state reaction. The influence of the partially replacing Ca^2 in CaTiO3 with Mg^2 , Sr^2 , Ba^2 , Zn^2 on the excitation spectra, the emission spectra and the long persistence properties were studied. The results suggest that certain quantity of Mg^2 , Sr^2 , Ba^2 , Zn^2 which partially replace Ca^2 can enhance the luminescent intensity and prolong the afterglow persistence of the samples. The intensity of Mg0.2Ca0.8TiO3: Pr^3 is above all of the samples. Take Mg0.2Ca0.8TiO3:Pr^3 as the basic sample, the influence of Pr^3 concentrations (C (Pr^3 )) on the long afterglow properties were also studied.The results suggest that when the C (Pr^3 ) is 0.10% (tool fraction) the intensity of the sample is the highest. The excitation spectra of all these samples show broad band spectra ranging from 300 - 500 nm peaking at about 342 nm. The emission spectra also exhibit a broad band peaking at 613 nm (CaTiO3: Pr^3 is 612 nm). XRD research indicates that the crystalline phases change due to the replacement of divalent metal ions. The research on the thermoluminescence spectra of Mg0.2Ca0.8TiO3:Pr^3 indicates that the peak is at 107.35℃ and the depth of the trap energy is about 0.852 eV.     

Long-Lasting Properties of Rare Earth-Doped Y2O2S Phosphors

The aim of this presentation is to report a new result of afterglow materials. The Y2O2S:Ln^3 (Ln = Sm, Tm)phosphors show bright reddish orange and orange-yellow colors when excited by UV or visible light. The main spectroscopic characterizations of Sm^3 and Tm^3 in yttrium oxysulfide and their long-lasting phosphorescence were measured and discussed in this presentation. Their long-lasting phosphorescence can be seen by the naked eyes clearly for about one hour in the dark room after the irradiation light sources were removed. XRD and photoluminescence (PL) spectra as well as the luminance decay were used to characterize these long-lasting phosphorescence phosphors. The results of XRD indicate that the products synthesized through the flux fusion method under 1050℃ for 6 h have a good crystallization without any detectable amount of impurity phase. Both the PL spectra and luminance decay results reveal that these phosphors have efficient luminescent and good long-lasting properties. We believe that the experimental data gathered in our present work will be useful in finding some new long-lasting phosphors with different colors.     

Synthesis of Long Afterglow Phosphor CaAl2Si2O8 ：Eu^2＋, Dy^3＋ via Sol-Gel Technique and Its Optical Properties

The long afterglow phosphor CaAl2Si2O8：Eu^2＋ , Dy^3＋ was prepared by a sol-gel method. The sol-gel process and the structure of the phosphor were investigated by means of X-ray diffraction analysis （XRD）. It is found that the single anorthite phase formed at about 1000 %, which is 300 % lower than that required for the conventional solid state reaction. The obtained phosphor powders are easier to grind than those of solid state method and the partical size of phosphor has a relative narrow distribution of 200 to 500 nm. The photoluminescence and afterglow properties of the phosphor were also characterized. An obvious blue shift occurs in the excitation and emission spectra of phosphors obtained by sol-gel and solid state reaction methods. The change of the fluorescence spectra can be attributed to the sharp decrease of the crystalline grain size of the phosphor resulted from the sol-gel technique.     

Luminescence Properties of Green-Emitting Phosphor （Ba1- x, Srx ） 2 SiO4 ： EU^2＋ for White LEDS

The （Ba1- x, Srx ） 2 SiO4 ： EU^2＋ green-emitting phosphors were synthesized by conventional solid-state reaction in a CO-reductive atmosphere, and their luminescent properties were investigated. The XRD data show that the Ba/Sr ratio not only affects the lattice parameters, but also influences the emission peak. The excitation spectra indicate that this phosphor can be effectively excited by UV light from 370 to 470 nm. The emission band is due to the 4f^65d^1→4f^7 transition of the Eu^2＋ ion. With an increase in x, the emission band shifts to longer wavelength and the reason was discussed. The emission spectra exhibit a satisfactory green performance under different excitation wavelength（380,398,412,420,460 nm）. （Ba1- x, Srx ） 2 SiO4 ： EU^2＋ is a promising phosphor for green white-lighting-emission diode by ultraviolet chip.     

Synthesis of Long Afterglow Phosphors MAI204：Eu^2＋ , Dy^3＋ （M=Ca, Sr, Ba） by Microemulsion Method and Their Luminescent Properties

Long afterglow phosphors MAl2O4：Eu^2＋ , Dy^3＋ （M = Ca, Sr, Ba） were synthesized by microemulsion method, and their crystal structure and luminescent properties were compared and investigated. XRD patterns of samples indicate that phosphors CaAl2O4：Eu^2＋, Dy^3＋ and SrAl2O4 ： Eu^2＋, Dy^3＋ are with monoelinie crystal structure and phosphor BaAl2O4：Eu^2＋ , Dy^3＋ is with hexagonal crystal structure. The wide range of excitation spectrum of phosphors MAl2O4： Eu^2 ＋ , Dy^3＋ （M = Ca,Sr, Ba） indicates that the luminescent materials can he excited by light from ultraviolet ray to visible light and the maximum emission wavelength of phosphors MAl2O4：Eu^2＋ , Dy^3＋ （M = Ca, Sr, Ba） is found mainly at λem of 440 nm （M = Ca）, 520 nm （M = Sr） and 496 nm （M = Ba） respectively, the corresponding colors of emission light are blue, green and eyna-green respectively. The afterglow decay tendency of phosphors can he summarized as three processes： initial rapid decay, intermediate transitional decay and very long slow decay. Afterglow decay curves coincide with formula I = At^ - n, and the sequence of afterglow intensity and time is Sr 〉 Ca 〉 Ba.     

Synthesis and Photoluminescence of BaMgAl10O17 ：Eu^2＋ Phosphor by Oxalate Co-precipitation Process

Single phase of Ba1-x MgAl10O17 ： x Eu^2＋ （0.02≤ x ≤ 0. 14） phosphors was first successfully prepared by coprecipitation in aqueous medium with a “reverse strike” method, using oxalic acid and ammonia together as precipitants. Completely crystallized phosphors were obtained at 1300 ℃, which is 300 ℃ lower than the temperature of solid-state reaction. Their photoluminescence was investigated under UV and VUV region, respectively. The emission spectra of Ba1-x MgAl10O17：xEu^2＋ samples excited by 254 or 147 nm showed a characteristic wide band with the peak centred at about 450 454 nm. Optimum emission intensity reached at x = 0.1 and then concentration quenching occurred. The synthesized phosphor shows 10% higher emission intensity than that prepared by solid-state reaction.     

Luminescent Properties of BaMgAl10O17： Eu2＋ Phosphors Coated with Y2SiO5

BaMgAl10O17： Eu^2＋ phosphors was prepared by the solid-reaction method. Y2SiO5 was coated uniformly on the surface of phosphor by the surface-coated method, and the luminescent and deterioration properties were discussed. The XRD and SEM results show that Y2SiO5 film is produced on the surface of BAM phosphor. The emission spectrum analysis shows that the peak of the phosphor does not change after coating. The two phosphors were applied to lamps and the deterioration was tested at different ignited time. The keep ratio of luminous flux of the phosphor coated with Y2SiO5 is higher than that of the uncoated phosphor.     

Luminescent properties of red phosphors K2Ba（MoO4）2：Eu3＋ for white light emitting diodes

K2Ba(MoO4)2:Eu3+ phosphors were synthesized by solid-state reaction. The emission and excitation spectra of K2 Ba(MoO4)2:Eu3+ phosphors exhibited that the phosphors could be effectively excited by near ultraviolet (394 nm) and blue (465 nm) light, and emitted red light at 616 nm. The influence of Eu3+concentration, sintering temperature and charge compensators (K+, Na+ or Li+ ) on the emission intensity were investigated. The results indicated that concentration quenching of Eu3+ was not observed within 30mol.% Eu 3+, 600 oC was a suitable sintering temperature for preparation of K2 Ba(MoO4)2:Eu3+phosphors, and K+ ions gave the best improvement to enhance the emission intensity. The CIE chromaticity coordinates of K2 Ba(MoO4)2:0.05Eu3+phosphor were calculated to be (0.68, 0.32), and color purity was 97.4%.     

Luminescence Properties of Sm^3＋ doped Bi2ZnB2O7

The phosphors of （Bi1- x Smx ） 2ZnB2O7 （ x = 0. 01, 0. 03, 0. 05, 0. 07, and 0. 09） were synthesized by conventional solid state reaction. The purity of all samples was checked by X-ray powder diffraction （XRD）. XRD analysis shows that all these compounds are of a single phase of Bi2ZnB2O7, indicating that the Bi^3＋ in Bi2ZnB2O7 can be partly replaced by the Sm^3＋ without the change of crystal structure. The excitation and emission spectra at room temperature show the typical 4f-4f transitions of Sm^3＋ . The dominant excitation line is around 404 nm due to ^6H5/2→^4K11/2 and the emission spectrum consists of a series of lines at 563, 599, 646, and 704 nm due to ^4G5/2→^6H5/2, ^6H7/2, ^6H9/2, and ^6H11/2, respectively. The optimal concentration of Sm^3＋ in Bi2ZnB2O7 is about 3mol% （relative to lmol Bi^3＋ ） and the critical distance Rc was calculated as 2.1 nm. The temperature dependence of the emission intensity of Bi1.94Sm0.06ZnB2O7 was examined in the temperature range between 100 and 450 K. The quenching temperature where the intensity has dropped to half of the initial intensity is 280 K. The lifetime for Sm^3＋ in Bi1.94Sm0.06ZnB2O7 is fitted as a value of 0.29 and 1.03 ms.     

Photoluminescent properties of tunable green-emitting oxynitride （Baa-xSrx）Si6012N2 ：Eu2＋ phosphor and its application in white LEDs

Green emitting Eu2＋-doped （Ba3_xSrx）Si6012N2 solid solutions were synthesized through solid state reaction at 1350 ℃ for 10 h under a N2/H2 atmosphere. The XRD patterns revealed that the solid solution series of （Ba3 x-ySrx）Si6Ol2N2：yEu2＋ with x value ranging from 0-0.6 were established. An efficient and intense tunable green light was observed by varying the cation Sr/Ba ratio. The emission spectra exhibited an entire shift towards long wavelength with increasing ofx value, which was caused by large crystal field splitting and Stokes shift. The x value dependence of emission intensity was discovered and explained by the enhanced probability of electron from excited 4f state to 5d ground state via nonradioactive transition. Highly thermal stability and feasible color coordinates were verified. White LEDs with excellent photochromic properties were fabricated by packing GaN based blue chips and （Ba Sr）3Si6012N2：Eu2＋ phosphors. All results indicated that the （Ba3_xSrx）SirO12N2：Eu2＋ phosphors were confirmed to be a promising candidate for pc-white LEDs in solid state lighting.     

Luminescence properties of Mn2） ions doped Lu2CaMg2Si3O1） garnet phosphors

Yttrium aluminum garnet structure phosphors Lu2CaMg2Si3O12:Mn2+ were synthesized by conventional high temperature solid-state reaction in reductive atmosphere. The structure and optical properties of samples were characterized by application of powder X-ray diffraction (XRD) and photoluminescence spectroscopy. Results of X-ray diffraction (XRD) analysis showed that the phosphors mainly presented garnet structure with a few weak peaks of impurity phases. Lu2-xCaMg2Si3O12:xMn2+ (x=0.01-0.8) phosphors showed a broad emission band peaking at around 590 nm under ultraviolet (UV) light of 408 nm when Mn2+ concentration was less than 0.08 mol. With an increase in the Mn2+ concentration (above 0.08), another broad emission band peaking at 720 nm besides 590 nm was observed, which may be due to manganese ion having different valence and occupying different host lattice. The critical quenching concentrations of manganese ion in the wavelength of 590 and 720 nm were about 0.06 and 0.2 mol, respectively. With 408 nm excitation wavelength, emission color of the samples had a red shift trend as the Mn2+ concentration increased. All the results indicated that the Lu2CaMg2Si3O12:Mn2+ phosphors could be applicable to n-UV based white LEDs.     

Influence of reaction parameters on the luminescence properties of monodisperse NaGd(1−x−y)(WO4)2:xEu3+,yTb3+ phosphor by molten salt synthesis

Eu~(3+) activated and Eu~(3+), Tb~(3+) co-activated monodisperse sodium double tungstates NaGd(WO4)2 phosphors were prepared by molten salt method at 750 ℃ for 10 h using NaCl as a flux. The crystal structure and morphology of the as-synthesized phosphors were measured by XRD and SEM, respectively. The photoluminescence properties were characterized by PL spectra, decay lifetime and CIE. The presence of NaCl plays an important role in the morphology and luminescence properties. In this work,NaCl and one of the raw material Na_2 CO_3 in a certain proportion will form a low eutectic salt to decrease the reaction temperature and benefit the formation of monodisperse NaGd(WO_4)_2 crystals. The color of Eu~(3+) and Tb~(3+) co-doped NaGd(WO_4)_2 phosphors can be tuned from creamy white to orange, red and green by adjusting the doping concentration of rare earth ions, since the emission contain the broad blue-green emission origin from NaGd(WO_4)_2 host and characteristic red and green emission origin from Eu~(3+) and Tb~(3+) ions. The electroluminescent spectra and CIE measurement shows that the LED device with NaGd_((1-x))(WO_4)_2:xEu~(3+)(x = 0.24) phosphor can be excited by 365 nm and 380 nm LED chip, and their CIE coordinate is(x = 0.45, y = 0.45) and(x = 0.36, y = 0.37), Ra is 80.3 and 86.3, T_c is 3196 and4556 K, respectively. As a single-component phosphor, NaGd(WO_4)_2:Eu~(3+),Tb~(3+) have potential application in UV-pumped WLEDs.     

Effects of Host Doping on Spectral and Long-Lasting Properties of Sm^3＋ -Doped Y2O2S

Gd- or Lu-doped long afterglow red phosphor Y2O2S：Sm^3＋ was synthesized using the high temperature flux fusion method. The obtained phosphors were analyzed using X-ray diffraction to determine the crystal structure, and the phase analyses show that the product is in single phase. The luminescence spectra and decay curve were measured on a Hitachi F-4500 fluorescence spectrophotometer. The decay time was determined on an ST-900PM weak light photometer. The analyses show that host doping of Lu improves both luminescence and decay time of the materials. The concentration of doped Lu and Sm was varied in order to determine the optimal condition and to synthesize the product with the best properties. The mechanism of the long afterglow was also briefly discussed.     

Luminescent Properties of Y2O3： Eu Nanocrystalls Synthesized by EDTA Complexing Sol-Gel Process

Y2O3: Eu nanocrystals were synthesized by EDTA complexing sol-gel process at a relatively low temperature, in which ethylen-diamine-tetraacetic acid (EDTA) and polyethylene glycol (PEG) were used as the chelating agent and polymerization agent respectively. Formation process of Y2O3:Eu and structure characterization were carried out by TG-DTA, XRD, SEM/EDX. The results show that pure cubic phase Y203: Eu nanocrystalsere is produced after the precursor calcinated at 600℃ for 2 h, and the crystallinity increases with increasing calcination temperature. The nanoparticles of the Y2O3: Eu are basically spherical in shape. The mean particle size increases from about 30 to 70 nm when the calcination temperature increases from 600 to 1000℃. The luminescent properties of phosphor were analyzed by measuring the excitation and emission spectra. The main emission peak of the sample is around 612 nm, resulting in a red emission. The emission intensity increases with the calcination temperature. Compared with microsized Y2O3: Eu phosphors prepared by a conventional method, nanosized Y2O3: Eu synthesized by the present work, gives and a clear red shift in the emission spectrum. Moreover, the quenching concentration of Eu is raised.     

Upconversion luminescence of Y2O3：Er^3＋ ,Yb^3＋ nanoparticles prepared by a homogeneous precipitation method

Y2O3： Er^3＋, Yb^3＋ nanoparticles were synthesized by a homogeneous precipitation method without and with different concentrations of EDTA 2Na. Upconversion luminescence spectra of the samples were studied under 980 nm laser excitation. The results of XRD showed that the obtained Y2O3：Er^3＋,Yb^3＋ nanoparticles were of a cubic structure. The average crystallite sizes calculated were in the range of 28-40 nm. Green and red upconversion emission were observed, and attributed to ^2H11/2,^4S3/2→^4I15/2 and ^4F9/2→^4I15/2 transitions of the ion, respectively. The ratio of the intensity of green emission to that of red emission drastically changed with a change in the EDTA 2Na concentration. In the sample synthesized without EDTA, the relative intensity of the green emission was weaker than that of the red emission. The relative intensities of green emission increased with the increased amount of EDTA 2Na used. The possible upconversion luminescence mechanisms were discussed.