共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
以广州蓄能水电厂为例,介绍了单导叶控制调速器导叶控制环的构成。针对导叶不同步跳闸故障进行了细致分析和推理,定位了故障点;通过解体检查找到了故障的具体原因,并实施了相应的处理和预防措施。 相似文献
4.
6.
7.
8.
9.
1概述调速器是水轮发电机的重要组成部分,水轮机调节系统根据机组转速的变化不断地改变水轮机过流流量,调速器的作用就是通过控制导叶接力器、桨叶接力器和接力器的操作油量来控制导叶(桨叶)的开度大小,进而控制水轮机过流的大小来调整水轮机的转速。当机组出现故障时应迅速关闭导叶接力器,控制水的流量,达到关机的目的。 相似文献
10.
11.
Analysis of causes of erosion-corrosion wear of the metal of internal surfaces of watered regions of tubes of heat-exchange devices 总被引:1,自引:0,他引:1
I. I. Belyakov V. I. Breus 《Power Technology and Engineering (formerly Hydrotechnical Construction)》2006,40(1):44-49
Causes of the appearance of erosion-corrosion wear (ECW) on inlet regions of tubes of heat-exchange devices are considered.
Experimental data are used for determining the mechanism of the ECW process and suggesting measures for its prevention.
__________
Translated from élektricheskie Stantsii, No. 11, November 2005, pp. 56–62. 相似文献
12.
介绍SIMHYD降水径流模型的结构及计算原理,利用该模型模拟了丹江口以上汉江上游流域的月流量过程,并采用区间分析方法分析SIMHYD模型参数的敏感性。结果表明:SIMHYD模型可以较好地模拟该流域的月流量过程;根据参数敏感性大小可将SIMHYD模型参数归为3类:第1类为敏感参数,如SMSC和SUB;第2类为较敏感参数,如CRAK和K;第3类为非敏感参数,如INSC,COEFF和SQ。 相似文献
13.
水利枢纽下游河道水位流量关系的变化 总被引:1,自引:0,他引:1
卢金友 《水利水运工程学报》1994,(Z1)
根据水利枢纽下游河道的实测资料,得到下游河道水位流量关系的调整变化,并对其变化原因进行了分析。 相似文献
14.
灌区渠道防渗的节水技术 总被引:1,自引:1,他引:0
随着水资源的短缺,提高农用水效率已迫在眉睫,而渠道防渗是当前灌区节水改造的重要内容之一,也是节水灌溉的重要途径。介绍了渠道防渗的各种措施及其优缺点,并从渠道规划设计、采用的衬砌材料不同及输水断面形式的不同三个方面加以阐述,重点提到了北方渠道的防冻涨破坏的要求,结合东北地区自然条件和社会经济条件提出了几种既适用又极易推广的渠道防渗措施。 相似文献
15.
16.
综述了电力系统故障诊断的各种研究方法,包括专家系统、人工神经网络、优化技术、Petri网络、粗糙集理论、模糊集理论和多代理技术等。简要分析了这些方法的特点与适用性,评述其存在的主要问题和值得改进之处。最后,以解决实际工程问题为目标,指出了该领域所需解决的关键技术问题和主要发展趋势,以促进该研究领域的进一步发展。 相似文献
17.
明槽均匀紊流的水力特性 总被引:13,自引:3,他引:10
由于实践的需要,人们对明槽水槽水流地大量的研究。近年来借助于激光测速技术使研究工作取得了一些进展。本文对明槽紊流的一些研究成果进行了总结与讨论。 相似文献
18.
19.
V. V. Artamonov 《Power Technology and Engineering (formerly Hydrotechnical Construction)》2003,37(2):114-119
A method of fabricating polymer replicas with the use of polymer solutions is described. It is shown that the adequacy of a replica is determined by the physicochemical processes on the microsection – polymer solution interface, in particular, by surface tension and wetting. The limiting wetting angle is determined for a number of polymer materials and solvents. The limiting wetting angle is shown to depend on the kind of material and on the kind of solvent as well as on their proportion in the solution. Polymer materials and solvents, the appropriate combination of which provides better wetting and hence better reflection of the studied microstructure by the replicas, are determined. The optical properties of polymer replicas, i.e., their reflectivity, resolving power, and contrast, are determined. The study makes it possible to pass from empirical to scientifically substantiated choice of materials, solvents, and their proportion for obtaining adequate replicas. 相似文献
20.