Stabilization of source-separated urine by biological nitrification process: treatment performance and nitrite accumulation

A laboratory study on nitrification of high-strength source-separated urine was conducted by means of sequencing batch reactors (SBR) and membrane bioreactors (MBR). The highest influent ammonia concentration for SBR and MBR reached more than 2,400 and 1,000 mg N/L, while the maximum pH was about 9 and 8.9, respectively. The ammonia oxidizing efficiency in both SBRs and MBRs was around 50%, which was restrained mainly by the deficiency of alkalinity in bulks. Meanwhile, the nitrite accumulation did also dominate in these two systems, and the major factor to inhibit the nitrite oxidization was thought to be the high free ammonia and free nitrous acid content in bulks. Hence, an ammonia nitrite solution was achieved with concentration ratio of 1:1; after that ammonia oxidation was restrained owing to the deficiency of alkalinity in urine. The temperature and influent ammonia content have no great influence on the nitrification process in both kinds of bioreactors. The nitrification can be progressed under a solids retention time (SRT) longer than 30 d; however, termination of ammonia oxidization was observed as the SRT fell below 20 d. The nitrifier biomass showed an excellent settleability, such that the suspended solids (SS) in effluent was of a low average, about 60 mg/L. This study on the stabilization of human urine will be useful to understand the process of urine separation from source.     

Nitrogen removal from pharmaceutical manufacturing wastewater with high concentration of ammonia and free ammonia via partial nitrification and denitrification.

In this study, laboratory-scale experiments were conducted applying a Sequencing Batch Reactor (SBR) activated sludge process to a wastewater stream from a pharmaceutical factory. Nitrogen removal can be achieved via partial nitrification and denitrification and the efficiency was above 99% at 23 degrees C+/-1. The experimental results indicated that the nitrite oxidizers were more sensitive than ammonia oxidizers to the free ammonia in the wastewater. The average accumulation rate of nitrite was much higher than that of nitrate. During nitrogen removal via the nitrite pathway, the end of nitrification and denitrification can be exactly decided by monitoring the variation of pH. Consequently, on-line control for nitrogen removal from the pharmaceutical manufacturing wastewater can be achieved and the cost of operation can be reduced.     

Treatment of nitrogen and phosphorus in highly concentrated effluent in SBR and SBBR processes.

Various sludge treatment processes produced supernatant with high ammonia concentration from 500 to 2,000 mgN/L and generally high phosphate concentration. Conversion of ammonia into nitrite via partial nitrification has proven to be an economic way, reducing oxygen and external COD requirements during the nitrification/denitrification process. Two processes with biomass retention are studied simultaneously: the sequencing batch reactor (SBR) and the sequencing batch biofilm reactor (SBBR). At a temperature of 30 degrees C, the inhibition of nitrite-oxidizing bacteria due to high ammonia concentration has been studied in order to obtain a stable nitrite accumulation. This work has confirmed the effect of pH and dissolved oxygen on nitrite accumulation performance. During a two month starting period, both processes led to nitrite accumulation without nitrate production when pH was maintained above 7.5. From a 500 mgN/L effluent, the performance of the SBR, and the SBBR, reached respectively about 0.95gN-NO2-/gN-NH4+, and 0.4gN-NO2-/gN-NH4+. The SBBR appears to be more stable facing disturbances in dissolved oxygen conditions. Finally, the maximal phosphate removal rates obtained in the SBR reached 90%, and 70% in the SBBR, depending on ammonium accumulation in the reactor. Ammonium phosphate precipitation is likely to occur, as was suggested by crystals observation in the reactor.     

The presence of ammonium facilitates nitrite reduction under PHB driven simultaneous nitrification and denitrification.

For economic and efficient nitrogen removal from wastewater treatment plants via simultaneous nitrification and denitrification the nitrification process should stop at the level of nitrite such that nitrite rather than nitrate becomes the substrate for denitrification. This study aims to contribute to the understanding of the conditions that are necessary to improve nitrite reduction over nitrite oxidation. Laboratory sequencing batch reactors (SBRs) were operated with synthetic wastewater containing acetate as COD and ammonium as the nitrogen source. Computer controlled operation of the reactors allowed reproducible simultaneous nitrification and denitrification (SND). The oxygen supply was kept precisely at a low level of 0.5 mgL(-1) and bacterial PHB was the only electron donor available for denitrification. During SND little nitrite or nitrate accumulated (< 20% total N), indicating that the reducing processes were almost as fast as the production of nitrite and nitrate from nitrification. Nitrite spiking tests were performed to investigate the fate of nitrite under different oxidation (0.1-1.5 mgL(-1) of dissolved oxygen) and reduction conditions. High levels of reducing power were provided by allowing the cells to build up to 2.5 mM of PHB. Nitrite added was preferentially oxidised to nitrate rather than reduced even when dissolved oxygen was low and reducing power (PHB) was excessively high. However, the presence of ammonium enabled significant reduction of nitrite under low oxygen conditions. This is consistent with previous observations in SBR where aerobic nitrite and nitrate reduction occurred only as long as ammonium was present. As soon as ammonium was depleted, the rate of denitrification decreased significantly. The significance of the observed strongly stimulating effect of ammonium on nitrite reduction under SND conditions is discussed and potential consequences for SBR operation are suggested.     

同步短程硝化反硝化研究

分析了现有短程硝化反硝化工艺处理高浓度氨氮废水所存在的问题,试验利用序批式反应器(SBR)的内部水力特性对其进行改造,以畜禽养殖废水为研究对象,从宏观上创造同步硝化反硝化(SND)条件,并实现了同一反应器内短程硝化反硝化的同步进行,改造后系统pH值下降速度减缓,反硝化效率提高,最终出水的亚硝酸盐和硝酸盐浓度分别降低了39%和38%。     

Low temperature biological phosphorus removal and partial nitrification in a pilot sequencing batch reactor system

Partial nitrification and biological phosphorus removal appear to hold promise of a cost-effective and sustainable biological nutrient removal process. Pilot sequencing batch reactors (SBRs) were operated under anaerobic/aerobic configuration for 8 months. It was found that biological phosphorus removal can be achieved in an SBR system, along with the partial nitrification process. Sufficient volatile fatty acids supply was the key for enhanced biological phosphorus removal. This experiment demonstrated that partial nitrification can be achieved even at low temperature with high dissolved oxygen (>3 mg/L) concentration. Shorter solid retention time (SRT) for nitrite oxidizing bacteria (NOB) than for ammonia oxidizing bacteria due to the nitrite substrate limitation at the beginning of the aeration cycle was the reason that caused NOB wash-out. Controlling SRT should be the strategy for an SBR operated in cold climate to achieve partial nitrification. It was also found that the aerobic phosphorus accumulating organisms' P-uptake was more sensitive to nitrite inhibition than the process of anaerobic P-release.     

Difficulties in maintaining long-term partial nitritation of ammonium-rich sludge digester liquids in a moving-bed biofilm reactor (MBBR).

Nitrogen can be eliminated effectively from sludge digester effluents by anaerobic ammonium oxidation (anammox), but 55-60% of the ammonium must first be oxidized to nitrite. Although a continuous flow stirred tank reactor (CSTR) with suspended biomass could be used, its hydraulic dilution rate is limited to 0.8-1 d(-1) (30 degrees C). Higher specific nitrite production rates can be achieved by sludge retention, as shown here for a moving-bed biofilm reactor (MBBR) with Kaldnes carriers on laboratory and pilot scales. The maximum nitrite production rate amounted to 2.7 gNO2-Nm(-2)d(-1) (3 gO2m(-3)d(-1), 30.5 degrees C), thus doubling the dilution rate compared to CSTR operation with suspended biomass for a supernatant with 700 gNH4-Nm(-3). Whenever the available alkalinity was fully consumed, an optimal amount of nitrite was produced. However, a significant amount of nitrate was produced after 11 months of operation, making the effluent unsuitable for anaerobic ammonium oxidation. Because the sludge retention time (SRT) is relatively long in biofilm systems, slow growth of nitrite oxidizers occurs. None of the selection criteria applied - a high ammonium loading rate, high free ammonia or low oxygen concentration - led to selective suppression of nitrite oxidation. A CSTR or SBR with suspended biomass is consequently recommended for full-scale operation.     

A novel wastewater treatment process: simultaneous nitrification, denitrification and phosphorus removal.

Simultaneous nitrification and denitrification (SND) via the nitrite pathway and anaerobic-anoxic enhanced biological phosphorus removal (EBPR) are two processes that can significantly reduce the COD demand for nitrogen and phosphorus removal. The combination of these two processes has the potential of achieving simultaneous nitrogen and phosphorus removal with a minimal requirement for COD. A lab-scale sequencing batch reactor (SBR) was operated in alternating anaerobic-aerobic mode with a low dissolved oxygen concentration (DO, 0.5 mg/L) during the aerobic period, and was demonstrated to accomplish nitrification, denitrification and phosphorus removal. Under anaerobic conditions, COD was taken up and converted to polyhydroxyalkanoates (PHA), accompanied with phosphorus release. In the subsequent aerobic stage, PHA was oxidized and phosphorus was taken up to less than 0.5 mg/L at the end of the cycle. Ammonia was also oxidised during the aerobic period, but without accumulation of nitrite or nitrate in the system, indicating the occurrence of simultaneous nitrification and denitrification. However, off-gas analysis found that the final denitrification product was mainly nitrous oxide (N2O) not N2. Further experimental results demonstrated that nitrogen removal was via nitrite, not nitrate. These experiments also showed that denitrifying glycogen-accumulating organisms rather than denitrifying polyphosphate-accumulating organisms were responsible for the denitrification activity.     

城市污水脱氮除磷SBR在线控制系统研究

SBR采用进水—厌氧—好氧—缺氧—好氧—沉淀—出水的运行方式处理城市污水。反应器装备有DO、ORP和pH等在线检测传感器。DO、ORP和pH变化的一些特征点可以用来判断和控制SBR中污水脱氮除磷过程的各个步骤。这包括:厌氧时,ORP和pH的转折点对应磷的释放;一次好氧时,DO、ORP的氨肘和pH的氨谷对应硝化结束;缺氧时,ORP的硝酸盐膝和pH的硝酸盐峰对应反硝化结束;二次好氧时,DO、ORP碳肘对应剩余碳的氧化结束,pH的转折点对应聚磷结束。控制系统能进行全自动运行来完成污水的脱氮除磷。     

Nitrogen removal from sludge digester liquids by nitrification/denitrification or partial nitritation/anammox: environmental and economical considerations.

In wastewater treatment plants with anaerobic sludge digestion, 15-20% of the nitrogen load is recirculated to the main stream with the return liquors from dewatering. Separate treatment of this ammonium-rich digester supernatant significantly reduces the nitrogen load of the activated sludge system. Two biological applications are considered for nitrogen elimination: (i) classical autotrophic nitrification/heterotrophic denitrification and (ii) partial nitritation/autotrophic anaerobic ammonium oxidation (anammox). With both applications 85-90% nitrogen removal can be achieved, but there are considerable differences in terms of sustainability and costs. The final gaseous products for heterotrophic denitrification are generally not measured and are assumed to be nitrogen gas (N2). However, significant nitrous oxide (N2O) production can occur at elevated nitrite concentrations in the reactor. Denitrification via nitrite instead of nitrate has been promoted in recent years in order to reduce the oxygen and the organic carbon requirements. Obviously this "achievement" turns out to be rather disadvantageous from an overall environmental point of view. On the other hand no unfavorable intermediates are emitted during anaerobic ammonium oxidation. A cost estimate for both applications demonstrates that partial nitritation/anammox is also more economical than classical nitrification/denitrification. Therefore autotrophic nitrogen elimination should be used in future to treat ammonium-rich sludge liquors.     

Rate of nitrate production during a two-stage nitrification batch reaction.

The two steps of nitrification, namely the oxidation of ammonia to nitrite and nitrite to nitrate, often need to be considered separately in process studies. It has been assumed that these two reactions can be described by single Monod models. In this paper, the suitability of the single Monod model for describing nitrite oxidation to nitrate is discussed. The measured rate of nitrate production during a batch reaction is presented. For the system studied it was found that nitrate production actually increased after the completion of ammonia oxidation. It is suggested that the reason for the increase was a combination of: (i) likely competition for oxygen when both substrates were present, and (ii) a decrease in ammonia inhibition of nitrite oxidisers with the removal of ammonia. The result is that a single Monod expression (based on nitrite as the substrate) could not be used to describe nitrate production. In these types of systems the consequence of oxygen limitation and substrate inhibition should also be considered.     

Nitrogen removal in a fluidized bed bioreactor by using mixed culture under oxygen-limited conditions.

Nitrogen removal involving nitrification and denitrification was investigated in a fluidized bed bioreactor by using mixed culture sludge under oxygen-limited conditions. Methane was used as a sole carbon source for denitrification. In this study, optimal nitrification and denitrification rates were examined by varying methane and oxygen gas dissolution flow rates, 90 ml/min, 400 ml/min and 650 ml/min, in each. Simultaneously nitrification and denitrification was achieved. The total nitrogen removal rate was 15-mg N/g VSS. d, 21-mg N/g VSS. d and 26.4-mg N/g VSS. d at gas dissolution flow rate 90 ml/min, 400 ml/min and 650 ml/min, respectively. No significant accumulation of nitrite was found in this experiment. Nitrogen removal rates depend on gas dissolution flow rates. DO concentration was at 0.5-2 mg/L.     

Nitrogen removal from piggery waste with anaerobic pretreatment.

Aerobic degradation of high strength piggery waste elevated the reactor temperature inhibiting nitrification. This study included anaerobic pretreatment with various influent by-pass rates to control the temperature and to minimize the external carbon requirement for denitrification. To find the optimum operating conditions, both lab-scale AnSBR (anaerobic sequencing batch reactor) and Ax/Ox (anoxic/oxic) SBR were operated at 35 degrees C. The heat energy released from Ax/Ox SBR was assumed to be used for heating the AnSBR, with which the Ax/Ox reactor temperature could successfully be controlled below 40 degrees C. The optimum rates of by-pass were 1.0 for winter, 0.4 for spring/fall and 0.2-0.4 for summer, respectively. Applying the correction factors for the measured AUR2 (nitrite nitrification rate) and AUR (nitrate nitrification) at the predicted temperatures, the required oxic HRTs were computed. The required Ax/Ox HRT ratios were respectively 0.5 for COD/TKN>8, 1.0 for COD/TKN ratio of 5.5-8 and 3.5 for below 5.5. The optimum HRTs were 16 days for AnSBR and 17 days for Ax/Ox SBR with the corrected AUR2.     

Nitrogen removal from sludge reject water by a two-stage oxygen-limited autotrophic nitrification denitrification process.

Nitrogen removal from sludge reject water was obtained by oxygen-limited partial nitritation resulting in nitrite accumulation in a first stage, followed by autotrophic denitrification of nitrite with ammonium as electron donor (similar to anaerobic ammonium oxidation) in a second stage. Two membrane-assisted bioreactors (MBRs) were used in series to operate with high sludge ages and subsequent high volumetric loading rates, achieving 1.45 kg N m(-3) day(-1) for the partial nitritation MBR and 1.1 kg N m(-3) day(-1) for the anaerobic ammonium oxidation MBR. Biomass retention in the nitritation stage ensured flexibility towards loading rate and operating temperature. Nitrite oxidisers were out-competed at low oxygen and high free ammonia concentration. Biomass retention in the second MBR prevented wash-out of the slowly growing bacteria. Nitrite and ammonium were converted to dinitrogen gas in a reaction ratio of 1.05, thereby maintaining nitrite limitation to assure process stability. The anoxic consortium catalysing the autotrophic denitrification process consisted of Nitrosomonas-like aerobic ammonium oxidizers and anaerobic ammonium oxidizing bacteria closely related to Kuenenia stuttgartiensis. The overall removal efficiency of the combined process was 82% of the incoming ammonium according to a total nitrogen removal rate of 0.55 kg N m(-3) day(-1), without adding extra carbon source.     

Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.     

Total nitrogen removal from high-strength ammonia recycle stream using a single submerged attached growth bioreactor.

An experimental study investigating the nitrogen removal efficiency from the recycle stream generated in the dewatering facility of the anaerobically digested sludge at the Deer Island wastewater treatment plant (WWTP) in Boston was conducted using a single submerged attached growth bioreactor (SAGB), designed for simultaneous nitrification and denitrification. The applied nitrogen loading to the reactor ranged from 0.7 to 2.27 kg-N/m3xd, and the corresponding total nitrogen (TN) removal rate ranged from 0.38 to 1.8 kg-N/m(3)xd. The observed nitrification rates varied from 0.42 kg-N/m3-d to 1.45 kg-N/m(3) xd with an ammonia load of 0.5 kg-N/m3-d and 1.8 kg-N/m(3)xd, respectively. An average nitrification efficiency of 91% was achieved throughout the experiment. Denitrification efficiency varied from 55%/o, obtained without any addition of carbon source, to 95% when methanol was added in order to obtain a methanol/nitrate ratio of about 3 kg methanol/kg NO3- -N.     

Modelling of biological nitrogen removal during treatment of piggery wastewater.

During this study, a mathematical model simulating piggery wastewater treatment was developed, with the objective of process optimisation. To achieve this, the effect of temperature and free ammonia concentration on the nitrification rate were experimentally studied using respirometry. The maximum growth rates obtained were higher for ammonium-oxidising biomass than for nitrite-oxidising biomass for the temperatures above 20 degrees C; values at 35 degrees C were equal to 1.9 and 1.35 day(-1), respectively. No inhibition of nitrification was observed for free ammonia concentrations up to 50 mgN/L. Using these data with others experimental data obtained from a pilot-scale reactor to treat piggery wastewater, a model based on a modified version of the ASM1 was developed and calibrated. In order to model the nitrite accumulation observed, the ASM1 model was extended with a two-step nitrification and denitrification including nitrite as intermediate. Finally, the produced model called PiWaT1 demonstrated a good fit with the experimental data. In addition to the temperature, oxygen concentration was identified as an important factor influencing the nitrite accumulation during nitrification. Even if some improvements of the model are still necessary, this model can already be used for process improvement.     

Achieving and maintaining of short-cut nitrification in a cyclic activated sludge system

A lab-scale Cyclic Activated Sludge Technology (CAST) system was operated more than 5 months to evaluate the effects of the operation mode on nitrogen removal performance and investigate a feasible method for achieving short-cut nitrification in the system. Results showed that nitrogen was removed by conventional biological nitrification and denitrification in traditional operation mode (fill/aeration 2 h, settle 1 h, decant 1 h), whereas short-cut nitrification and denitrification was the main nitrogen removal pathway in modified operation mode and the nitrogen removal performance was enhanced. Short-cut nitrification was successfully achieved in CAST system at 17 ± 1 °C by adjusting operation conditions and the average total nitrogen removal efficiency increased by 11.4% compared to traditional mode. It was assumed that low dissolved oxygen (<1.0 mg/L) limitation combined with free ammonia (0.28-0.34 mg/L) inhibition on nitrite-oxidizing bacteria caused nitrite accumulation in modified mode. During maintaining period of short-cut nitrification, preset aeration time enhanced ammonium-oxidizing bacteria dominance. It was also found that low DO could result in overgrowth of filamentous microorganisms and poor sludge settleability. The pH variation could provide effective information for controlling aeration duration in modified mode. However, no evident breakpoint appeared on pH and DO profiles in traditional mode.     

Effect of denitrification type on pH profiles in the sequencing batch reactor process.

Laboratory batch experiments were conducted to investigate pH profiles during partial and complete denitrification with sufficient organic carbon source. Five stirred tank-type glass vessels, with a 7 L working volume for each, were used as SBR reactors that were all operated in denitrification mode. Five levels of initial proportion of nitrogen substances, i.e. nitrate and nitrite, were used in five reactors, respectively. Results showed that, at given temperature and mixed liquor suspended solids (MLSS), partial denitrification could attain a higher pH value than complete denitrification at the end of denitrification with the same initial NOx- concentration. The larger proportion the nitrite took in initial NOx- concentration, the higher pH peak would be obtained on pH profiles during denitrification despite the same total alkalinity produced. It was found that different types of alkalinity were produced during biological denitrification with different nitrogen substances. Partial denitrification could more carbonate alkalinity produce than complete denitrification. Furthermore, some characteristic points were identified on pH profiles which could indicate the disappearance of not only nitrate, but also nitrite in system. When computers are used to detect these features, they can provide rapid, real-time information, regarding the biological state of the system.     

Partial nitrification of sludge reject water by means of aerobic granulation

Granular sludge formation was performed in a laboratory scale Sequencing Batch Reactor (SBR) fed with supernatant of anaerobic digestion of sewage sludge. This effluent was concentrated progressively in order to enhance biomass capacity without inhibiting it. During the first part of the study, ammonium nitrogen was converted to nitrate, so conventional nitrification took place. When a nitrogen load of 0.8 g N L(-1) d(-1) was treated, the effluent concentration of nitrite started to increase while the nitrate concentration decreased until it disappeared. So, partial nitrification was achieved. At the end of this study, a nitrogen load of 1.1 g N L(-1) d(-1) was treated obtaining an effluent with 50% ammonium and 50% nitrite. The volatile suspended solids concentration in the reactor reached 10 g VSS L(-1). At this point the granule morphology was quite round and no filamentous bacteria was observed. The Feret's diameter was in the range between 1 and 6 mm with an average value of 4.5 mm. Roundness value was all the time higher than 0.7. Granule density increased during the experimental period, obtaining a final value of 7.0 g L(-1).