磨边机的磨削过程的数学模型的研究

在参考金属磨削过程动态模型以及对墙地砖磨边机磨削过程分析折基础上,建立了磨边机磨削数学动态模型。该模型反映了砖的形态等因素与磨削力的关系,并提出了改进磨边机磨削质量的途径。     

理想的的固体推进剂粘合剂的分子结构

对粘合剂的分子结构和固体推进剂的力学以及流变性能之间的关系进行了研究.由发动机中药住的操作条件对推进剂力学性能的要求以及已有的加工技术对药浆流变性能的限制出发.反推得出固体推进剂粘合剂理想的分子结构.结构和加工要求是由三种类型的火箭发动机的应用要求决定的:航天转运、运载火箭和弹道导弹以及空对空战术导弹.考虑了可满足这些应用要求的三种一般的配方.除假想的全粘合剂推进剂外,还包括传统的复合和硝酸酯增塑的推进剂配方.对这三类中的各种配方按分子量、交联密度、溶解度参数、链的刚硬性、单体的摩擦系数、填充物的体积分数和增塑剂的体积分数确定了各种聚合物的分子特性.10个聚合物粘合剂系统的特性数据说明了它们的分子结构如何影响制得的推进剂的性能.     

合成氨的生产工艺的现状及发展趋势的探讨

本文通过对合成氨的工艺流程和发展情况对合成氨的生产工艺的现状及发展趋势进行阐述。     

物理化学的概念教学的启发式模式的构建

通过对目前物理化学教材内容和讲授模式的分析,针对在概念著述和课堂讲授中存在的误区,结合物理化学家吉布斯的启发式教学典故,本文构建一种"立足客观自然、环环相扣启发"的概念教学模式,以"焓"概念的讲授为例,化抽象为直观,收了良好的教学效果。启发式模式对当前物理化学的概念教学有重要的参考价值。     

神彩的玻璃 神秘的宗教 神圣的殿堂

在国外学习艺术玻璃这几年,谈起彩色玻璃镶嵌,自然会联想到欧洲教堂里的彩色玻璃窗。它是中世纪教堂装饰的一种独特方法,主要盛行于罗马式、哥特式和拜占庭式建筑。前两种建筑的窗户多而大,几乎布满整个建筑立面,便于采光。     

丁二酸酐的生产工艺的研究

丁二酸酐的化学简式是C4H4O3丁二酸酐是医药、染料、涂料的主要原材料,同时还是重要的药物和化学试剂成分,另外丁二酸酐可以用于生胃酮、琥珀酸胺噻唑的生产,并且可以广泛的应用于树脂的合成和制备。目前工业上对丁二酸酐的制备主要有以下两种方法：第一种方法就是对顺丁烯二酸酐的直接催化加氢法。现在对顺丁烯二酸酐直接催化加氢的生产工艺流程研究的比较广泛,特别是对丁二酸酐生产工艺中的热力学以及探索新的催化研究体系等方面的研究更为广泛;第二种方法就是直接对丁二酸进行脱水。第二种方法的主要优点就在于它对环境污染较小且不使用苯类溶剂,所以国内外很多丁二酸酐生产厂家都普遍采用第二种方法。     

优质的产品 完善的服务 理想的选择

<正>企业概述为了满足石油化工、有色冶炼、硫磷工业、环境保护、焦化行业技术的快速发展以及生产规模的不断扩大带来的市场需求,"扬州建业投资有限公司"和"扬州庆松化工设备有限公司"部分股东共同组建了"建业庆松集团有限公司"。新成立的"建业庆松集团有限公司"将传承老公司的优秀业绩、优良传统,发扬新公司的开拓理念、创新精神,     

硫铁矿的pH的研究

在市场经济条件下,矿山必须适应市场和满足用户要求,以好的产品质量来赢得用户和占领市场。提高产品质量关键在于控制矿石品位及杂质等指标的稳定性,出口硫铁矿(以下简称“出口矿”)除了S、Fe、Pb、Zn、Cu、SiO2、C、H2O、粒度的指标控制外,个别客户还要求pH在5~6之间,而我们出口矿S品位在45~48以上的pH一般在2~4之间,为满足客户的需求,我们必须降低出口矿的酸度即提高pH,这关系到配矿的工艺流程。     

面向未来的强大的合作伙伴

13馆、A13展位——作为阿博格参加历届K展这一国际展览盛事的传统位置,今年该公司的展位依然保持不变。除此之外,与往届一样,阿博格将以崭新的产品和技术亮相K2010：独特的Selogica特性、大型高性能液电混合机器和实现部件高效生产的复杂生产单元,以及诸多的应用技术和模具技术,都将首次向全球展出。     

煤炭地下气化高温井筒温度场研究

基于井筒与地层的传热情况,根据能量守恒及井筒传热原理,考虑物性参数随温度和压力变化,建立了生产井井筒的温度场预测模型,形成了求解算法和数学仿真模型,研究了温度场的影响因素。结果表明:产出气各物性沿井深分布差异较大,在分析时有必要耦合考虑;随着日产量和井底温度增加,井筒各段的温度均上升,其中日产量在30×10⁴ m³/d时,井口的产出气温度最高(686℃),井底温度在1000℃时,井口温度为588℃;井底压力对温度场影响很小,在工程应用中可忽略不计;随着井深增加,井口温度下降。     

晶须长径比对复合材料力学行为影响的模拟

在单向晶须增强树脂基复合材料的轴对称模型和已有研究成果基础上,利用有限元分析方法,研究该类复合材料中晶须长径比的变化对材料整体力学行为的影响.结果表明:1)晶须长径比对晶须应力作用明显大于对基体的影响;2)晶须的长径比h/r≤30时,随着晶须长径比的增大,发生在晶须端部处的集中应力急剧增加;但当长径比h/r≥30时,长径比的进一步增加对集中应力影响不大;3)随着晶须长径比的增大,界面剪切应力减小,分布曲线下移;但当长径比h/r≥30时,长径比的进一步增加对剪切应力影响不大;4)随着晶须长径比的增加,复合材料的拉伸强度逐渐增大.     

The service of the hearths of arc furnaces for melting stainless steels with the use of oxygen

Conclusions During the operation of arc furnaces specializing in the melting of stainless steels, chemical and phase changes occur in the magnesite hearths which lead to the formation of a single type structure in the monolith of rammed layer and upper courses of the structure.Petrographic studies showed that the monolith was formed as a result of phase inversions of the minerals of the hearth under the influence of the silicate constituents of the slag being produced, which partly settles to the bottom after discharge of the melt. These inversions greatly affect the physicochemical properties of the hearth and especially the refractoriness. The inversions which increase the refractoriness include the process of recrystallization of the periclase and chrome-spinel with the formation of strong and dense periclase-spinel growths in the upper layers of the hearth.The reduction in the refractoriness occurs owing to the formation of montichellite under the influence of calcium slag constituents and the gradual replacement of the forsterite by this silicate, and also the partial solution of periclase in the silicate melt.The thermal resistance of the hearth is favorably affected by the fact that the new silicate formations are distributed irregularly over the height of the hearth, and the nature of the distribution depends on their fluidity and temperature gradient in the hearth. In view of this consistency, the most refractory silicates, such as forsterite and mervenite, are localized in the upper strata of the hearth, and the montichellite, being the most fusible silicate, migrates to the lower layers.The result of all the processes and phase inversions taking place in the hearth is that the refractoriness of the most important layers of hearth (upper and middle) remains high during service. The reduction in refractoriness in the lower layer cannot greatly affect the life of the hearth since this layer is quite far away from the working region of the furnace and is in the low-temperature region.Large amounts of metals are detected only in the part of the hearth located in direct contact with the furnace bath; metal does not take a large part in the processes occurring in the hearth.The positive influence of the additions of chromite on the life of the hearth of electric furnaces determined during operation, can be explained by the fact that the chromite is essential for the formation of refractory chromespinel phases [2], contributes to the formation of periclase-spinel growths in the upper parts of the hearth, and accelerates the process of removing the less refractory silicates from the upper layers of the hearth to the lower [3].     

直缝式燃烧器W火焰锅炉新型二次风箱特性研究

为解决直流缝隙式燃烧器W火焰锅炉原设计的全通二次风大风箱由于锅炉炉膛宽度宽、风箱截面尺寸大等原因产生的炉膛中部缺风问题,华能上安电厂将4号锅炉原风箱改造为分隔型新型二次风箱。新型二次风箱改造完成后对其特性的试验研究表明,常规冷态通风时拱上、拱下各喷口及各风道区域之间风速偏差较小。单侧送风机运行且联络门关闭时,送风机停运侧各喷口风速明显低于送风机工作一侧,但通过拱上、拱下二次风门的调整,能有效缓解由于单侧送风机运行带来的喷口风速偏差。单侧送风机运行联络门开启的情况下,3个风道区域平均风速的偏差与正常双送风机运行时差别不大。与改造前相反,锅炉运行炉膛出口氧量已呈现中间高两头低的趋势,适当调整二次风箱风门开度后炉膛出口氧量分布趋于均衡,说明改造后的二次风箱风门能有效调节炉内二次风配风进而改变炉膛出口氧量分布。通过二次风箱风门开度的适当调整,能有效降低SCR入口NOx浓度,保证锅炉经济环保运行。     

Effect of preparation conditions on the properties of microspheres prepared using an emulsion-solvent extraction process

Methylaluminoxane microspheres were prepared using a hydrocarbon-in-perfluorocarbon-emulsion solvent extraction process. The effect of the preparation conditions on the size of the microspheres was investigated. As expected, the size of the microspheres decreased with increasing stirring speed. At low surfactant concentrations the size of the microspheres was independent of the surfactant concentration. However, the size of the microspheres decreased as the surfactant concentration was further increased. The size of the microspheres was not only affected by the surfactant concentration but also by the volume ratio of the dispersed phase to the continuous phase. At a low volume ratio of the phases the effect of the surfactant on the size of the microspheres was larger than the effect of the increased volume ratio of the phases. At high volume ratios of the phases the effect of the volume ratio of phases on the size of the microspheres became more significant than the effect of the surfactant. A slow solidification increased the formation of non-spherical microspheres.     

The role of the symmetry and the flexibility of the anion on the characteristics of the nanostructures and the viscosities of ionic liquids☆

The transport properties of ionic liquids (ILs) are crucial properties in view of their applications in electrochem-ical devices. One of the most important advantages of ILs is that their chemical–physical properties and conse-quently their bulk performances can be well tuned by optimizing the chemical structures of their ions. This will require elucidating the structural features of the ions that fundamentally determine the characteristics of the nanostructures and the viscosities of ILs. Here we showed for the first time that the“rigidity”, the order, and the compactness of the three-dimensional ionic networks generated by the anions and the cation head groups determine the formation and the sizes of the nanostructures in the apolar domains of ILs. We also found that the properties of ionic networks are governed by the conformational flexibility and the symmetry of the anion and/or the cation head group. The thermal stability of the nanostructures of ILs was shown to be con-trolled by the sensitivity of the conformational equilibrium of the anion to the change of temperature. We showed that the viscosity of ILs is strongly related to the symmetry and the flexibility of the constitute ions rather than to the size of the nanostructures of ILs. Therefore, the characteristics of the nanostructures and the viscosities of ILs, especially the thermal stability of the nanostructures, can be fine-tuned by tailoring the symmetry and the conformational flexibility of the anion.     

纳米填料/橡胶体系在贮存中的结构形态变化Ⅱ.结构变化的影响因素及其对性能的影响

综述了纳米填料／橡胶复合体系在熔融态或高弹态贮存停放过程中,影响其结构形态变化的因素,以及贮存停放对复合体系流变性能、物理机械性能和导电性能的影响,并评述了相关的理论模型。纳米填料／橡胶复合体系在熔融贮存过程中的结构变化主要受橡胶的黏度、填料特性及其用量、填料与橡胶之间的相互作用以及加工性能的影响。填料网络结构的絮凝程度强化使复合体系流变性能、动态力学性能降低,但导电性能提高。相关的填料聚集动力学和填料絮凝模型大部分是唯象模型。     

复合材料风扇叶片榫头铺层设计及加工制造

碳纤维复合材料风扇叶片榫头段是铺层数量最多、递减铺层最集中的部位,榫头的铺层质量影响叶片的低周疲劳强度。为完成叶片榫头段的铺层设计,基于铺层设计准则,建立了一种适用于航空发动机复合材料风扇叶片榫头段铺层设计的方法。根据铺层高度大小将铺层分为结构层和插入层,在结构层铺层设计中考虑了高度递减层的角度与铺放位置。在插入层铺层设计中,考虑了单组插入层铺层数量、单组插入层内部铺层顺序及铺层角度、单组插入层形成的坡度、相邻插入层之间的错开距离等五个方面的因素,确定了单组插入层的结构及其在榫头的分布。根据设计方案对榫头进行加工制造,成型的榫头试样件厚度检测质量良好,证实了该铺层设计方法的可行性。     

转炉一次除尘新OG系统高效喷淋塔喷嘴布置方式对喷淋特性的影响

采用离散相模型对新OG系统高效喷淋塔入口段及主体段喷嘴的布置方式进行数值模拟,考察了喷嘴喷射方向和喷淋层数对雾化场气流分布和降温效果的影响。结果表明,喷嘴的喷射方向和塔内的喷淋层数对雾化场的气流分布和降温效果影响较大;喷淋塔入口段采用逆流喷射时,出口截面的速度分布最均匀且降温效果最好;高效喷淋塔的主体段的喷淋层数为5时,塔内烟气的速度流场较均匀,且中心区域的气流速度为2~4 m/s,有助于延长气体与液滴的作用时间;随喷淋层数增加,塔内温度梯度变化增大,水蒸气质量分数分布与温度分布对应,塔内的平均湍动能逐渐增高。     

聚丙烯气相反应器工艺参数的计算和控制

以液相本低聚合和气相聚合组合式聚丙烯（PP）装置生产多相共聚PP产品为例，推导出了多相共聚PP生产中气相反应器工艺参数之间的关系式，并讨论了工艺参数对产品性能的影响，通过控制气相反应器的乙烯进料量与气相比，改变产品的抗冲击性能，乙烯含量越高，产品的抗冲击性能越好，刚性越差，无定形二聚物的含量越高，产品的抗冲击性能越好，但刚性相对降低。