Properties and structural characterization of oxidized starch/PVA/α‐zirconium phosphate composites

Two series of composites, i.e., polyvinyl alcohol (PVA)/oxidized starch (OST)/exfoliated α‐zirconium phosphate (POST‐ZrPn) and PVA/starch (ST)/exfoliated α‐zirconium phosphate (PST‐ZrPn), were fabricated using a casting and solvent evaporation method. The composites were characterized by Fourier transform infrared spectroscopy (FT‐IR), thermal gravimetric analysis (TGA), differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (XRD), scanning electron microscopy (SEM), tensile testing, and moisture uptake. Compared with PST‐ZrPn, POST‐ZrPn films with the same component ratio showed higher tensile strength (σ_b), lower elongation at break (ε_b) and improved water resistance. Additionally, in the POST‐ZrPn series, σ_b and ε_b increased with an increase in α‐zirconium phosphate (α‐ZrP) loading; however, higher α‐ZrP loads resulted in the aggregation of α‐ZrP particles. Compared with POST‐ZrP0, the values for σ_b, ε_b, and water resistance of POST‐ZrP3, containing 1.5 wt % α‐ZrP, were increased by 128.8%, 51.4%, and 30.2%, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Chitosan–graphene oxide nanocomposites: Effect of graphene oxide nanosheets and glycerol plasticizer on thermal and mechanical properties

In this study, graphite oxide (GO) is synthesized from natural graphite flakes by the modified Hummers method. Characterization by Fourier transform infrared, X‐ray photoelectron, Raman and ultraviolet‐visible spectroscopies, X‐ray diffraction, and thermogravimetric analysis is conducted on GO to confirm the oxidation of graphite. Unplasticized and glycerol plasticized chitosan/graphene oxide (CS/GO) nanosheets nanocomposites with different GO loadings are prepared by solution casting. The combined effect of GO and glycerol on structure, thermal and mechanical properties of nanocomposite films is studied. GO nanosheets are well dispersed throughout the CS matrix due to the hydrogen bonding and electrostatic interactions between CS and GO nanosheets. The incorporation of GO within the CS matrix results in a decrease of the crystallinity, an improvement of thermal stability, and a significant enhancement of the stiffness and tensile strength that is emphasized by the glycerol. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45092.     

Graphene oxide reinforced chitosan/polyvinylpyrrolidone polymer bio‐nanocomposites

Bio‐nanocomposite films based on chitosan/polyvinylpyrrolidone (CS/PVP) and graphene oxide (GO) were processed using the casting/evaporation technique. It has been found that the three components of bio‐nanocomposites can be easily mixed in controlled conditions enabling the formation of thick films with high quality, smooth surface and good flexibility. Structural and morphological characterizations showed that the GO sheets are well dispersed in the CS/PVP blend forming strong interfacial interactions that provide an enhanced load transfer between polymer chains and GO sheets thus improving their properties. It has been found that the water resistance of the CS/PVP blend is improved, and the hydrolytic degradation is limited by addition of 0.75 and 2 wt % GO. The modulus, strength, elongation and toughness of the bio‐nanocomposites are together increased. Herein, the steps to form new bio‐nanocomposite films have been described, taking the advantage of the combination of CS, PVP and GO to design the aforementioned bio‐nanocomposite films, which allow to have extraordinary properties that would have promising applications as eventual packaging materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41042.     

The structure and properties of a novel nanocomposite films from chitosan and layered zirconium phosphonate

A new type of layered zirconium phosphonate (zirconium glycine‐N, N‐dimethylphosphonate, abbreviated as ZGDMP), with functional group of ‐COOH, has been successfully prepared and characterized by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). To confirm the effect of the functional group ‐COOH on the structure and properties of composites, a series of chitosan/zirconium phosphonate modified by n‐butylamine (BA‐ZGDMP) nanocomposite films were prepared by casting process. FTIR spectra suggested that strong interactions existed between BA‐ZGDMP and chitosan matrix. Compared to neat CS film, tensile strength (σ_b) and elongation at break (ε_b) of the nanocomposite film improved by 35.1% and 15.6%, respectively, with loading ratio of just 1.0 wt %. In addition, the BA‐ZGDMP also improved the water resistance of the nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Enhanced mechanical and thermal properties of biodegradable poly(butylene succinate‐co‐adipate)/graphene oxide nanocomposites via in situ polymerization

Poly(butylene succinate‐co‐butylene adipate) (PBSA)/graphene oxide (GO) nanocomposites were synthesized via in situ polymerization for the first time. Atomic force microscopy demonstrated the achievement of a single layer of GO, and transmission electron microscopy proved the homogeneous distribution of GO in the PBSA matrix. Fourier transform infrared spectroscopy results showed the successful grafting of PBSA chains onto GO. With the incorporation of 1 wt % GO, the tensile strength and flexural modulus of the PBSA were enhanced by 50 and 27%, respectively. The thermal properties characterized by differential scanning calorimetry and thermogravimetric analysis showed increases in the melting temperatures, crystallization temperatures, and thermal stability. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4075–4080, 2013     

Effect of octa(aminopropyl) polyhedral oligomeric silsesquioxane (OapPOSS) functionalized graphene oxide on the mechanical,thermal, and hydrophobic properties of waterborne polyurethane composites

A novel graphene nanomaterial functionalized by octa(aminopropyl) polyhedral oligomeric silsesquioxane (OapPOSS) was synthesized and then confirmed by Fourier transform infrared spectroscopy, thermogravimetric analysis (TGA), Raman spectroscopy, X‐ray photoelectron spectroscopy, transmission electron microscopy, scanning electron microscopy with energy‐dispersive X‐ray spectroscopy (SEM EDX), atomic force microscopy, and X‐ray diffraction. The obtained functionalized graphene (OapPOSS‐GO) was used to reinforce waterborne polyurethane (WPU) to obtain OapPOSS‐GO/WPU nanocomposites by in situ polymerization. The thermal, mechanical, and hydrophobic properties of nanocomposites as well as the dispersion behavior of OapPOSS‐GO in the polymer were investigated by TGA, a tensile testing machine, water contact angle tests, and field emission SEM, respectively. Compared with GO/WPU and OapPOSS/WPU composites, the strong interfacial interaction between OapPOSS‐GO and the WPU matrix facilitates a much better dispersion and load transfer from the WPU matrix to the OapPOSS‐GO. It was found that the tensile strength of the OapPOSS‐GO/WPU composite film with 0.20 wt % OapPOSS‐GO exhibited a 2.5‐fold increase in tensile strength, compared with neat WPU. Better thermal stability and hydrophobicity of nanocomposites were also achieved by the addition of OapPOSS‐GO. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44440.     

Reinforcement of the mechanical properties in nitrile rubber by adding graphene oxide/silicon dioxide hybrid nanoparticles

Graphene oxide (GO) and silicon dioxide (SiO₂) nanoparticles have been hybridized for improving the mechanical and dynamic mechanical properties of nitrile rubber (NBR). SiO₂ nanoparticles were homogeneously dispersed on the surface and between layers of GO, and the new hybrid nanoparticles formed (GO/SiO₂₎ had better thermal stability than GO. To evaluate the mechanical properties, GO/SiO₂/NBR nanocomposites were prepared by solution blending and mechanical solution methods. It was observed that tensile strength increased in a larger grade in GO/SiO₂/NBR nanocomposites than that in GO/NBR and SiO₂/NBR nanocomposites, while the elongation at break only changes smoothly. Moreover, dynamics measurements also indicated that the elasticity increased after adding GO/SiO₂ hybrid nanoparticles in NBR. From morphology's analysis of GO/SiO₂/NBR and GO/NBR nanocomposites, it is was conclude that the hybridization of the GO/SiO₂ was the determining factor for the reinforcement of the mechanical properties and elasticity of the NBR. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46091.     

Impact of various oxidation degrees of graphene oxide on the performance of styrene–butadiene rubber nanocomposites

In this work, graphene oxide (GO) with various oxidation degrees were synthesized by adjusting the dosage of oxidation agent based on a modified Hummers' method, and were then used for the fabrication of the styrene–butadiene rubber (SBR)/GO nanocomposites through latex coagulation method, followed by a high‐temperature cure process. The vulcanization characteristics, thermal stability, mechanical properties, thermal conductivity as well as solvent resistance of SBR/GO nanocomposites were investigated. The results indicated that various surface structures of GO due to oxidation degrees may lead to different dispersion states of GO in the rubber matrix, and thus greatly influenced the cure rate, mechanical properties as well as thermal conductivity of SBR/GO nanocomposites. The optimal (moderate) oxidation degree of GO was achieved at the oxidation agent (KMnO₄)/graphite weight ratio 9/5, for which case the tensile strength, tear strength, and thermal conductivity of SBR/GO nanocomposites increased by 271.3%, 112.3%, and 28.6%, respectively, compared with those of neat SBR. In addition, the mentioned nanocomposites also showed the best solvent resistance in toluene. POLYM. ENG. SCI., 58:1409–1418, 2018. © 2017 Society of Plastics Engineers     

Dispersion of multiwalled carbon nanotubes in polyacrylonitrile‐co‐starch copolymer matrix for enhancement of electrical,thermal, and gas barrier properties

Nanomaterials gained great importance on account of their wide range of applications in many areas. Carbon nanotubes (CNTs) exhibit exceptional electrical, thermal, gas barrier, and tensile properties and can therefore be used for the development of a new generation of composite materials. Functionalized multiwalled carbon nanotubes (MWCNTs) reinforced Polyacrylonitrile‐co‐starch nanocomposites were prepared by in situ polymerization technique. The structural property of PAN‐co‐starch/MWCNT nanocomposites was studied by X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The conductivity, tensile strength, and thermal properties of nanocomposites were measured as a function of MWCNT concentrations. The thermal stability, conductivity, and tensile strength of PAN‐co‐starch/MWCNT nanocomposites were improved with increasing concentration of MWCNTs. Oxygen barrier property of PAN‐co‐starch/MWCNT nanocomposites was calculated and it was found that, the property was reduced substantially with increase of MWCNTs proportion. The synthesized PAN‐co‐starch/MWCNT nanocomposites may used for electrostatically dissipative materials, aerospace or sporting goods, and electronic materials. © 2013 Society of Plastics Engineers     

Green fabrication of porous chitosan/graphene oxide composite xerogels for drug delivery

Porous chitosan (CS)/graphene oxide (GO) composite xerogels were prepared through a simple and “green” freeze‐drying method. Scanning electron microscopy, Fourier transform infrared spectrometry, powder X‐ray diffraction, and compressive strength measurements were performed to characterize the microstructures and mechanical properties of as‐prepared composite xerogels. The results show that the incorporation of GO resulted in an observable change in the porous structure and an obvious increase in the compressive strength. The abilities of the composite xerogels to absorb and slowly release an anticancer drug, doxorubicin hydrochloride (DOX), in particular, the influence of different GO contents, were investigated systematically. The porous CS/GO composite xerogels exhibited efficient DOX‐delivery ability, and both the adsorption and slow‐release abilities increased obviously with increasing GO content. Additionally, the best adsorption concentration of DOX was 0.2 mg/mL, and the cumulative release percentage of DOX from the xerogels at pH4 much higher than that at pH 7.4. Therefore, such porous CS/GO composite xerogels could be promising materials as postoperation implanting stents for the design of new anticancer drug‐release carriers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40006.     

SiO2-covered graphene oxide nanohybrids for in situ preparation of UHMWPE/GO(SiO2) nanocomposites with superior mechanical and tribological properties

The modified Hummer technique was used in the preparation of graphene oxide (GO) nanosheets, and then SiO₂ decorated GO [GO(SiO₂)] nanosheets were synthesized via the sol–gel method. Then, ultrahigh-molecular-weight polyethylene (UHMWPE) nanocomposites loaded with 0.5, 1, 1.5, and 2 wt % of GO(SiO₂) were prepared using magnesium ethoxide/GO(SiO₂)-supported Ziegler–Natta catalysts via the in situ polymerization. Morphological study of the prepared polymer powders was assessed using field-emission scanning electron microscopy, which showed that GO(SiO₂) nanohybrids have been uniformly dispersed and distributed into the UHMWPE matrix. Also, the neat UHMWPE and its nanocomposites were evaluated with different analyses, including viscosity-average molecular weight measurement, differential scanning calorimetry, thermogravimetric analysis, tensile test, scratch hardness, and pin-on-disk test. The characterization of the UHMWPE nanocomposites indicated that many characterizations, including the mechanical, thermal, and tribological properties of UHMWPE, were significantly improved by incorporation of these new nanosheets in spite of the molecular weight reduction of the polymeric matrix and the improved flowability and processability of the produced nanocomposite. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47796.     

Synergistic effects of modified TiO2/multifunctionalized graphene oxide nanosheets as functional hybrid nanofiller in enhancing the interface compatibility of PLA/starch nanocomposites

The aim of this study is to investigate the synergistic effects of modified TiO₂/multifunctionalized graphene oxide nanosheets at different ratios on the interface compatibility between starch and poly(lactic acid) (PLA). To this end, silanylated nano-TiO₂ (MTiO₂, 1 and 2%) and alkylated maleic anhydride grafted graphene oxide (f-GO, 0.1, 0.2, and 0.4%) at different combinations are blended with the PLA-starch composites using solution blending technique. Then, the synergistic effects of MTiO₂ and f-GO on PLA/starch matrix are investigated in terms of the morphology, crystallinity, structural characterization, thermal stability, dynamic mechanical, and antiaging properties, and the related mechanisms. The Raman and Fourier transform infrared spectroscopy spectra verify the successful synthesis of the two modified nanofillers (f-GO and MTiO₂) and the formation of strong hydrogen bond within the PLA-starch nanocomposites. Due to the strong interfacial interaction and the synergistic effect from the combination of 1% MTiO₂ and 0.2% f-GO, obvious improvement was observed in PLA-starch versus other nanocomposites in terms of morphology, thermal stability, surface hydrophobicity, storage modulus, ultraviolet-shielding capacity, and aging-resistance. Furthermore, differential scanning calorimeter (DSC), isothermal crystallization kinetic, and X-ray diffraction analysis demonstrate that f-GO and the M-TiO₂ significantly synergize in enhancing the crystallization rate and crystallinity of PLA/starch matrix. These results provide novel insights for constructing high-performance nanocomposites and facilitate their applications in food packaging.     

Enhancement of thermal,morphological, and mechanical properties of compatibilized based on PA6-enriched graphene oxide/EPDM-g-MA/CR: Graphene oxide and EPDM-g-MA compatibilizer role

In this study, a series of elastomeric nanocomposites based on specific amounts of polyamide6 (PA6)/chloroprene rubber (CR) blends which are compatibilized with ethylene propylene diene monomer-grafted-maleic anhydride (EPDM-g-MA) and different amounts of graphene oxide (GO) were prepared with melt mixing method. The effect of compatibilizer and reinforcement concentration in the PA6/CR blend matrix was investigated using theoretical and experimental analysis. Dispersion of nanoplatelets within rubber blend matrix was proven with transmission electron microscopy and field emission-scanning electron microscopy. The modified microstructure of samples showed the significant effect of EPDM-g-MA and GO on the size reduction of CR droplets in the PA6 continuous phase. The results from differential scanning calorimetry and dynamic mechanical thermal analysis revealed the effect of EPDM-g-MA and GO as an effective nucleating agent in PA6-enriched GO/CR (PA6EGO/CR). The findings obtained from thermogravimetric analysis displayed that the GO in the presence of an EPDM-g-MA as a compatibilizer can cause a higher thermal stability in PA6EGO/CR. From mechanical properties, by adding a compatibilizer to the PA6/CR blend, the tensile strength changed from 39.0 to 45.1, the Young's modulus altered from 522.2 to 716.0 and the elongation at break changed from 246.8 to 222.2. While incorporation of 5 phr of GO to the compatibilized blend, the tensile strength increased by 25.2%, the Young's modulus increased by 36.6% and the elongation at break decreased by 20%. The Christensen–Lo model used for analyzing the stiffness of PA6EGO/EPDM-g-MA/CR with emphasis on the influence of the interphase region to predict the effect of various loadings of GO and EPDM-g-MA of Young's modulus. The rheology and creep tests showed a significant effect of EPDM-g-MA and GO content on the rheology behavior of nanocomposites.     

Effect of graphene oxide on the behavior of poly(amide‐6‐b‐ethylene oxide)/graphene oxide mixed‐matrix membranes in the permeation process

Polyether‐block‐amide (Pebax)/graphene oxide (GO) mixed‐matrix membranes (MMMs) were prepared with a solution casting method, and their gas‐separation performance and mechanical properties were investigated. Compared with the pristine Pebax membrane, the crystallinity of the Pebax/GO MMMs showed a little increase. The incorporation of GO induced an increase in the elastic modulus, whereas the strain at break and tensile strength decreased. The apparent activation energies (E_p) of CO₂, N₂, H₂, and CH₄ permeation through the Pebax/GO MMMs increased because of the greater difficulty of polymer chain rotation. The E_p value of CO₂ changed from 16.5 kJ/mol of the pristine Pebax to 23.7 kJ/mol of the Pebax/GO MMMs with 3.85 vol % GO. Because of the impermeable nature of GO, the gas permeabilities of the Pebax/GO MMMs decreased remarkably with increasing GO content, in particular for the larger gases. The CO₂ permeability of the Pebax/GO MMMs with 3.85 vol % GO decreased by about 70% of that of the pristine Pebax membrane. Rather than the Maxwell model, the permeation properties of the Pebax/GO MMMs could be described successfully with the Lape model, which considered the influence of the geometrical shape and arrangement pattern of GO on the gas transport. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42624.     

ZrO2 functionalized graphene Oxide/SEBS‐Based nanocomposites for efficient electromagnetic interference shielding applications

ZrO₂‐coated graphene oxide (GO)/SEBS(styrene‐ethylene‐butylene‐styrene)‐based nanocomposites were prepared for use as an electromagnetic interference (EMI) shielding material. Transmission electron microscopy (TEM) reveals almost every individual GO is fully and homogeneously covered with uniform ZrO₂. X‐ray diffraction (XRD) patterns and Differential scanning calorimetry (DSC) revealed increased ordering of ‐(CH₂‐CH₂)n segments in the poly(ethylene‐co‐1‐butene) block of the SEBS matrix in the case of SEBS/ZrO₂‐coated graphene oxide composites than in the SEBS/pristine graphene oxide nanocomposite. Thermogravimetric analysis (TGA) proved better oxidation resistance of SEBS/ZrO₂‐coated GO nanocomposite compared to that of SEBS/pristine GO nanocomposite. The present nanocomposites exhibited excellent EMI shielding effectiveness (SE) over X‐band (8.2 GHz–12.4 GHz) with EMI SE of 37.9 dB. J. VINYL ADDIT. TECHNOL., 25:E130–E136, 2019. © 2018 Society of Plastics Engineers     

Facile preparation and characterization of poly(vinyl alcohol)/chitosan/graphene oxide biocomposite nanofibers

Poly(vinyl alcohol) (PVA)/chitosan (CS)/graphene oxide (GO) biocomposite nanofibers have been successfully prepared using aqueous solution by electrospinning. CS colloidal gel in 1% acetic acid can be changed to homogeneous solution by using electron beam irradiation (EBI). The uniform distributions of GO sheets in the nanofibers were investigated by field emission scanning electron microscopy (FESEM) and Raman spectroscopy. FESEM images illustrated that the spread single GO sheet embedding into nanofibers was formed via self-assembly of GO sheet and PVA/CS chains. And the average diameters of the biocomposite nanofibers decreased (200, 173, 160 and 123 nm) with increasing the contents of GO (0.05, 0.2, 0.4 and 0.6 wt%). Raman spectra verified the presence of GO in the biocomposite nanofibrous mats. The mechanical properties of as-prepared materials related with GO contents. It revealed that the highest tensile strength was 2.78 MPa, which was 25% higher than that of neat PVA/CS nanofibers. Antibacterial test demonstrated that the addition of GO to PVA/CS nanofiber had great ability to increase inhibition zone till 8.6 mm. Overall, these features of PVA/CS/GO nanofibers which were prepared by eco-friendly solvent can be a promising candidate material in tissue engineering, wound healing and drug delivery system.     

Synthesis and electrochemical properties of graphene oxide/nanosulfur/polypyrrole ternary nanocomposite hydrogel for supercapacitors

A method for synthesizing Graphene oxide (GO)/nano‐sulfur/polypyrrole (PPy) ternary nanocomposite hydrogel is depicted. The higher surface area of GO, PPy porous structure and their excellent conductivity are utilized, and the GO hydrogel can be made easily. The products are characterized by field‐emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, and electrochemical workstation. The results demonstrated that GO/nano‐S/PPy ternary nanocomposite hydrogel is successfully synthesized. The electrochemical properties are investigated by cyclic voltammetry, galvanostatic charge/discharge measurements, and cycling life in a three‐electrode system in 1M Li₂SO₄ electrolyte solution. The GO/nano‐S/PPy ternary nanocomposite hydrogel exhibit a high specific capacitance of 892.5 F g^?1 at scan rates of 5 mV s^?1 and the capacitance retain about 81.2% (594.8 F g^?1) of initial capacitance (732.5 F g^?1) after 500 cycles at a current density of 1 A g^?1. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40814.     

Fabrication and characteristics of graphene oxide/nanocellulose fiber/poly(vinyl alcohol) film

Poly(vinyl alcohol) (PVA), PVA/nanocellulose fiber (CNF), and PVA/CNF/graphene oxide (GO) films were prepared simply by casting stable aqueous mixed solutions. FTIR investigation indicated that hydrogen bonding existed between the interface of GO and PVA‐CNF. Scanning electron microscopy and X‐ray diffraction analysis showed that GO was uniformly dispersed in PVA‐CNF matrix. Introducing CNF into PVA caused a significant improvement in tensile strength, and further incorporating GO into PVA/CNF matrix led to a further increase. The tensile strength of the neat PVA film, PVA/CNF composite, and PVA/CNF/GO film (0.6 wt % GO) was 43, 69, and 80 MPa, respectively. Moreover, when incorporating 8 wt % CNF into PVA matrix, O₂ permeability and water absorption decreased from 13.36 to 11.66 cm³/m²/day and from 164.2% to 98.8%, respectively. Further adding 0.6 wt % GO into PVA/CNF matrix resulted in a further decrease of permeability and water absorption to 3.19 cm³/m²/day and 91.2%, respectively. Furthermore, for all composite samples, the transmittance of visible light was higher than 67% at 800 nm. CNF and GO‐reinforced PVA with high mechanical and barrier properties are potential candidates for packaging industry. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45345.     

Ultrasound assisted continuous‐mixing for the preparation of PP/SEBS/OMMT ternary nanocomposites

Polypropylene (PP)/polystyrene‐block‐poly(ethylene‐co‐butylenes)‐block‐polystyrene (SEBS)/organo‐montmorillonite (OMMT) nanocomposites of varying concentrations of maleic anhydride‐grafted polypropylene (PP‐g‐MA) were prepared by continuous mixing assisted by ultrasonic oscillation. The structure and morphology of nanocomposites were investigated by X‐ray diffraction (XRD), transmission electron microscopy, and scanning electron microscopy. It was found that both PP‐g‐MA and ultrasonic oscillation could enhance the intercalation and exfoliation of OMMT in PP matrix. Meanwhile, the formation of PP could be induced by ultrasonic irradiation at a power of more than 540 W. Rheological properties including complex viscosity, storage, and loss modulus of nanocomposites were increased after adding PP‐g‐MA or ultrasonic treatment. The results of mechanical properties showed that PP‐g‐MA could improve the tensile strength and tensile modulus of nanocomposites, but with the sacrifice of impact strength. This problem could be improved by ultrasound due to the reduced particle size of SEBS. However, the mechanical properties would be reduced by ultrasonic treatment with higher intensity due to the polymer degradation. Therefore, the synergistic effect of both compatibilizer and ultrasound should account for the balance between toughness and stiffness of PP/SEBS/OMMT ternary nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41202.     

Structure and properties of polypropylene/hydrotalcite nanocomposites

This article presents the study of the modification of the particle/matrix interface region and its effects on the structure and dynamic mechanical behavior of polypropylene (PP)/hydrotalcite nanocomposites prepared by melt extrusion. The interface modification was promoted by combinying the organophillization of the hydrotalcite particles with blending the PP with a maleic anhydride‐grafted‐PP (PP‐g‐MAH) or a maleic anhydride‐grafted‐poly(styrene‐co‐ethylenebutylene‐co‐styrene) (SEBS‐g‐MAH). Sodium dodecyl sulphate was used to promote the organophillization of the hydrotalcite particles. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) showed a partially exfoliated hydrotalcite structure, with an increasing exfoliation being achieved by adding a compatibilizer and organo‐modifying the particles. Values of the Young's modulus (E), storage modulus (E′), maximum tensile strength (σ_max), neck propagation strength (σ_neck), and elongation at break (ε_b) were found to depend both on the nature of the particle matrix interface as well as on the type of compatibilizer. Also, nanocomposites prepared with the organophillized particles showed lower T_g and loss factor values. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers