Sustainable biocarbon as an alternative of traditional fillers for poly(butylene terephthalate)-based composites: Thermo-oxidative aging and durability

Sustainable biocomposites have gained considerable interest as an alternative to conventional composites in recent years due to their cost-effectiveness and environmental friendliness. The aim of this study was to investigate the performance and durability behavior of biocomposites from sustainable biocarbon (BC) as compared to conventional established fillers. The poly(butylene terephthalate) (PBT) and its composites reinforced with BC, talc, and glass fiber (GF) were prepared and the durability performances was investigated. The study showed that BC/PBT biocomposites provided a lighter weight alternative to traditionally used fillers. After undergoes thermo-oxidative aging, the mechanical properties of BC/PBT biocomposite were deteriorated. The GF/PBT showed the most stable in retaining its mechanical properties in comparison to the talc/PBT and BC/PBT. The aging behavior and mechanism of the PBT composites were discussed. This study provides further insight on the durability-related properties progression of biocomposites as compared to traditional used fillers. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47722.     

Mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

Polypropylene (PP) hybrid composites have been produced by compounding two types of mineral fillers, viz., talc and kaolin with PP copolymer using a twin screw extruder. The PP hybrid composite was injection‐molded into dumbbell specimen for tensile, flexural, and impact properties characterizations. MFI and SEM studies were used to characterize the flow and morphological properties of the PP hybrid composites. The result shows that most of the hybrid composites showed a significant decrease in flow, tensile, flexural, and impact properties compared with the single filler‐filled PP composites. However, a hybridization effect was seen for the PPT20K10 hybrid composites, through the synergistic coalescence of positive characteristics from 20 wt % of talc and 10 wt % of kaolin. This hybrid formulation have given an economically advantageous material with the mechanical properties (tensile, flexural, and impact) comparable to those of the talc‐filled PP composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 434–441, 2007     

Mechanical properties,morphology, and crystallization behavior of polypropylene/elastomer/talc composites

In this study, polypropylene/ethylene–octene copolymer (PP/POE) blends, PP/talc, and PP/POE/micro‐talc (MT) composites were fabricated using a twin screw. To estimate the performances of the PP/POE blends, PP/talc, and PP/POE/MT composites, mechanical properties, heat deflection temperature (HDT), thermomechanical analysis, and isothermal crystallization characterization were conducted. Incorporating talc particles increased the tensile strength, flexural properties, and HDT of the PP matrix, but reduced the elongation at break and notched impact strength. The inclusion of POE elastomers in the PP matrix yielded the opposite effect on PP/talc composites. PP/POE/MT composites provide a compromise that improves both the flexural properties and notched impact strength. Moreover, the inclusion of talc particles in PP/POE blends induced heterogeneous nucleation and considerably reduced the crystallization time. Consequently, the time required for processing was also greatly reduced. POLYM. COMPOS., 36:69–77, 2015. © 2014 Society of Plastics Engineers     

Modification of polypropylene composites containing potassium titanate whisker and talcum

Modified polypropylene was prepared by blending with potassium titanate whisker (PTW) and 10 w/w% talc via Haake extruder followed by injection molding. Reinforced with both PTW and talc, the PP composites exhibited better mechanical properties. The tensile modulus and flexural modulus of PP composites tend to increase with the increasing of whisker concentrations. The talc plays a synergistic role in improving the mechanical properties of composites and reducing cost. Torque measurement shows the PP composites has a good processing condition due to lubrication of PTW. TGA test shows PP composites containing 20 w/w% PTW and 10 w/w% talc is useful for improving PP composite's thermo oxidative stability. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Sustainable biocomposites from biobased polyamide 6,10 and biocarbon from pyrolyzed miscanthus fibers

The reinforcing effects of biocarbon of varying particle size ranges (crushed, <500, 500–426, 250–213, and <63 µm) on biobased polyamide 6,10 (PA 6,10) at 20 wt % loading were investigated for the resulting biocomposites. The heat deflection temperature and impact strength were observed to increase with reduction in particle size. Also, a 200% increase in the impact strength was observed in the biocomposite with biocarbon particles sized at <63 µm when compared to that with <500 µm. A 50% and 83% increase in the tensile and flexural moduli of the biocomposite with biocarbon particle size of <500 µm was observed, respectively, while the tensile strength was observed to remain unchanged. The flexural strength of the biocomposites was improved by 61% when compared to neat nylon. These results were due to good wetting, dispersion and increased surface area of the biocarbon within the nylon matrix. These results show the potential of biocarbon as reinforcing filler in nylon for applications especially in the automotive industry. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44221.     

Preparation and Rheological and Mechanical Properties of Poly(butylene succinate)/Talc Composites for Material Extrusion Additive Manufacturing

In this paper, poly(butylene succinate) (PBS) with a low melting point and a similar performance to polyethylene is employed as a printing material; talc is introduced into the matrix to enhance the melt strength of pure PBS during printing. The PBS/talc composite 3D printing filament is prepared by melt extrusion, and the thermal, mechanical, morphological, and rheological properties of the composites are investigated. The results show that the addition of talc to PBS leads to an increase in crystallization temperature. In addition, the tensile and flexural strengths of the injection‐molded specimens increase when the talc concentration increases. However, the mechanical properties of the printed specimens exhibit an opposite variation trend due to their distinct forming process. The printing temperature is 135 °C, which is far lower than those of commercial grade polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) printing filaments. Scanning electron microscopy (SEM) images show that increasing the talc concentration creates better printed formability and well‐organized fracture surface structures. By comparing printed fishbones, the results suggest that the presence of talc leads to a good printing performance with the composite. Furthermore, the rheological results reveal that η^*, G′, and G″ are enhanced by the addition of talc.     

Bleached extruder chemi‐mechanical pulp fiber‐PLA composites: Comparison of mechanical,thermal, and rheological properties with those of wood flour‐PLA bio‐composites

An environmentally friendly bleached extruder chemi‐mechanical pulp fiber or wood flour was melt compounded with poly(lactic acid) (PLA) into a biocomposite and hot compression molded. The mechanical, thermal, and rheological properties were determined. The chemical composition, scanning electron microscopy, and Fourier transform infrared spectroscopy results showed that the hemicellulose in the pulp fiber raw material was almost completely removed after the pulp treatment. The mechanical tests indicated that the pulp fiber increased the tensile and flexural moduli and decreased the tensile, flexural, and impact strengths of the biocomposites. However, pulp fiber strongly reinforced the PLA matrix because the mechanical properties of pulp fiber‐PLA composites (especially the tensile and flexural strengths) were better than those of wood flour‐PLA composites. Differential scanning calorimetry analysis confirmed that both pulp fiber and wood flour accelerated the cold crystallization rate and increased the degree of crystallinity of PLA, and that this effect was greater with 40% pulp fiber. The addition of pulp fiber and wood flour modified the rheological behavior because the composite viscosity increased in the presence of fibers and decreased as the test frequency increased. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44241.     

Mechanical properties of talc‐ and (calcium carbonate)‐filled poly(vinyl chloride) hybrid composites

The main objective of this study was to investigate and compare the mechanical properties of poly(vinyl chloride) (PVC) composites filled with calcium carbonate (CaCO₃), talc, and talc/CaCO₃. Talc and CaCO₃ with different grades were incorporated into the PVC matrix. To produce the composites, the PVC resin, fillers, and other additives were first dry‐blended by using a laboratory mixer before being milled into sheets in a two‐roll mill. Test specimens were prepared by compression molding, after which the mechanical properties of the composites were determined. Single and hybrid filler loadings used were fixed at 30 phr (parts per hundred parts of resin). Talc‐filled composite showed the highest flexural modulus and the lowest impact strength, whereas uncoated, ground, 1‐μm CaCO₃ (SM 90) showed optimum properties in terms of impact strength and flexural modulus among all grades of CaCO₃. It was selected to combine with talc at different ratios in the hybrid composites. The impact strength of the hybrid composites gradually increased with increasing SM 90 content, but the flexural and tensile properties showed an opposite behavior. Hybrid (10 phr talc):(20 phr SM 90)‐filled PVC composite reached a synergistic hybridization with balanced properties in impact strength, as well as flexural and tensile properties. J. VINYL ADDIT. TECHNOL., 2012. © 2012 Society of Plastics Engineers     

Effect of chemical treatments on the mechanical,flow, and morphological properties of talc‐ and kaolin‐filled polypropylene hybrid composites

This study was performed with commercially available phenyl trimethoxysilane (PTMS) and neoalkoxytitanate [i.e., neopentyl(diallyl)oxytri(dioctyl)phosphato titanate (LICA 12)] as coupling agents. PTMS and LICA 12 were used to treat talc and kaolin to compare their effects with untreated fillers upon incorporation into polypropylene (PP). Single‐filler PP composites (containing either talc or kaolin) and hybrid‐filler composites (containing a mix of both talc and kaolin) were compounded in a twin‐screw extruder and subsequently injection‐molded into dumbbells. The incorporation of PTMS and LICA 12 slightly decreased the tensile and flexural properties in terms of modulus and strength but increased the elongation at break for both single‐filler and hybrid‐filler composites. There was also a significant improvement in the impact strength of the composites, particularly those treated with LICA 12. The hybrid composites, through the synergistic coalescence of positive characteristics from talc and kaolin with the aid from chemical treatment provided an economically advantageous material with mechanical properties comparable to those of the single‐filler‐filled PP composites. Further investigations on flow and morphological properties were also done to correlate the mechanical properties of the single‐ and hybrid‐filler‐filled PP composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

高流动高模量高抗冲聚丙烯复合材料的制备及性能研究

研究了弹性体（POE）、滑石粉(talc)、乙撑双硬脂酰胺（EBS）的含量对高流动、高模量、高抗冲聚丙烯（PP）复合材料的力学性能、熔体流动速率、结晶温度、热稳定性以及微观断面结构的影响。结果表明,需要25份POE才能使高流动性共聚PP发生完全脆韧转变;通过熔融共混制备PP、POE、talc复合材料（PP/POE/talc）,当复合材料的质量份数比为80∶20∶40时,制得的PP/POE/talc复合材料的熔体流动速率为22.9 g/10 min、弯曲模量为1 887.7 MPa、缺口冲击强度为31.2 kJ/m2;对比纯PP,其弯曲模量提高了102.2 %,缺口冲击强度提高了217.8 %,弯曲强度提高了2.6 %,拉伸强度降低了15.1 %;添加1份EBS能够同时提高PP/POE/talc复合材料的熔体流动速率与缺口冲击强度。     

Silica‐filled polypropylene composites: The effect of ethylene diamine dilaurate and maleic anhydride grafted polypropylene on mechanical properties,water absorption,morphology, and thermal properties

The effect of two compatibilizers, i.e. ethylene diamine dilaurate (EDD) and maleic anhydride grafted polypropylene (MAPP) on the mechanical properties, water absorption, morphology, and thermal properties of silica‐filled polypropylene (PP/Sil) composites were studied. The results show that the tensile, impact and flexural strengths (up to 2 php), Young's modulus, and elongation at break (Eb) increased with increasing EDD content. However, increasing MAPP content increases the tensile strength, Young's modulus, impact and flexural strengths, and water absorption resistance. At a similar compatibilizer content, EDD exhibits higher Eb, impact and flexural strengths but lowers tensile strength, Young's modulus, and water absorption resistance compared with MAPP. Scanning electron microscopy study of tensile fractured surfaces exhibits the evidence of better silica‐PP adhesion with MAPP and EDD compared with the similar composites but without compatibilizer. Fourier transform infra red spectra provide an evidence of interaction between EDD or MAPP with PP/Sil composites. Termogravimetry analysis results indicate that the addition of EDD or MAPP slightly increases the thermal stability of PP/Sil composites. Differential scanning calorimetry also indicates that PP/Sil composites with EDD or MAPP have higher heat fusion (ΔH_f(com)) and crystallinity (X_com) than similar composites but without compatibilizer. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Effect of alkali treatment on properties of unidirectional isora fibre reinforced epoxy composites

Abstract

Unidirectional isora fibre reinforced epoxy composites were prepared by compression moulding. Isora is a natural bast fibre separated from Helicteres isora plant by retting process. The effect of alkali treatment on the properties of the fibre was studied by scanning electron microscopy (SEM), IR, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Mechanical properties such as tensile strength, Young's modulus, flexural strength, flexural modulus and impact strength of the composites containing untreated and alkali treated fibres have been studied as a function of fibre loading. The optimum fibre loading for tensile properties of the untreated fibre composite was found to be 49% by volume and for flexural properties the loading was optimised at ～45%. Impact strength of the composite increased with increase in fibre loading and remained constant at a fibre loading of 54·5%. Alkali treated fibre composite showed improved thermal and mechanical properties compared to untreated fibre composite. From dynamic mechanical analysis (DMA) studies it was observed that the alkali treated fibre composites have higher E' and low tan δ maximum values compared to untreated fibre composites. From swelling studies in methyl ethyl ketone it was observed that the mole percentage of uptake of the solvent by the treated fibre composites is less than that by the untreated fibre composites. From these results it can be concluded that in composites containing alkalised fibres there is enhanced interfacial adhesion between the fibre and the matrix leading to better properties, compared to untreated fibre composites.     

Effects of acid,alkaline, and seawater aging on the mechanical and thermomechanical properties of glass fiber/epoxy composites filled with carbon nanofibers

Owing to the superior corrosion resistance, fiber-reinforced polymer (FRP) composites are the prime choice of structural materials for various marine and chemical industries, where there is a long-term direct contact of the components takes place with corrosive fluids. In this present work, glass fiber/epoxy (GE) composites have been fabricated with and without carbon nanofibers (CNFs), and aging has been carried out in acidic (pH = 1), seawater (pH = 8.2), and alkaline (pH = 13) solutions for 150 days. The resistance of CNF-filled GE composites toward the corrosive fluids has been evaluated in terms of alteration in the mechanical (flexural), microstructural (fractography analysis by field emission scanning electron microscope), and thermomechanical (dynamic mechanical analysis) behavior of the materials. It is revealed that as the immersion time increases, there is a continuous decrement in flexural strength and modulus, and glass-transition temperature (T_g) of all the materials in all these solutions. Compared to the 1% CNF-filled GE composite, control GE composite showed more degradation in the case of alkaline aging and seawater aging. Maximum reduction (56%) in the strength of GE composite was observed due to 150 days of alkaline aging. However, the control GE composite showed better resistance to the acidic solution than that of CNF-filled GE composite. Possible failure modes, changes in the chemistry of the material due to aging have been studied by fractography analysis. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48434.     

多元复合高流动性聚丙烯的制备与性能

研究了滑石粉(Talc)及偶联剂用量、均聚聚丙烯(PP-H)与马来酸酐接枝物(PP-g-MAH)及PP-H对高流动性共聚聚丙烯(PP)性能的影响;比较了在填充20%Talc的共聚PP中分别添加PP-g-MAH和PP-H的复合体系力学性能及流变性能的变化规律。结果表明:钛酸酯偶联剂用量为1%(相对于Talc)时,所得Talc填充共聚PP综合性能最佳;当Talc用量大于10%时,共聚PP/Talc复合材料的拉伸强度、冲击强度、弯曲强度、熔体流动速率随Talc含量的增加而逐渐下降,弯曲模量则逐渐提高;PP-g-MAH对高流动性共聚PP的拉伸强度增强效果明显优于PP-H,PP-H则使共聚PP的熔体流动性明显下降。     

Study of plastic compounds containing polypropylene and wood derived fillers from waste of different origin

The scope of the article was to study the perspectives of the using of wood derived fillers (WDF) from waste of different origin as fillers of polypropylene. The WDF used in this study was hard wood flour (HW), birch veneer polishing dust (VD) and tetra‐pack carton cellulose fiber (TC). Some mechanical strength parameters, water uptake in the static and cyclic test and resistance to fungal decay of polypropylene (PP) composites containing these three types of WDF were studied and compared with similar loading (40 wt %) talc‐filled PP. Composites containing TC and VD fibers as filler showed the highest flexural strength at three test temperatures (?40, +20, and +40°C) and flexural modulus and tensile strength at plus temperatures. On the other hand talc‐filled PP exhibited greatest flexural modulus at minus temperature, greatest impact strength at room temperature and best flow ability. Significant difference was observed between PP composites with HW and VD fillers regarding water uptake in cyclic tests, however flexural strength and modulus change of composites were reversible after drying. No weight loss of WDF/PP composites was observed after 6 week exposure to brown‐ and white‐rot fungi, however, degradation of the surface of samples was detected by SEM. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

PVDF/PMMA/Basalt fiber composites: Morphology,melting and crystallization,structure, mechanical properties,and heat resistance

This paper is to study the effect of basalt fiber on morphology, melting and crystallization, structure, mechanical properties, melting and crystallization of PVDF/PMMA composites using scanning electron microscopy (SEM), X‐ray, differential scanning calorimeter (DSC), dynamical mechanical analysis (DMA), etc. Basalt fiber may disperse well in PVDF/PMMA matrix and form compact fiber network, and this makes tensile and flexural strength of fiber reinforced PVDF/PMMA composites get to the maximum value of 62 and 102 MPa, respectively. However, the mechanical properties begin to decrease when basalt fiber content exceeds 20 wt %. The α and β phase of PVDF can coexist in composites, and basalt fiber and PMMA can induce β phase of PVDF. The melting temperature of PVDF in composites is kept unchanged, but the degree of crystallinity of composites increases as basalt fiber content increase, and then declines when fiber content exceeds 20%. The DSC results confirm that the nucleation ability of PVDF is enhanced by basalt fiber. Also, the heat resistance of PVDF/PMMA composite is improved from 133 to 146.1°C due to basalt fiber. The DMA shows that basalt fiber increases the storage modulus of PVDF/PMMA composite, and the loss peak of PMMA increases from 116.1 to 130°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40494.     

Surface‐modified talc particles by acetoxy groups grafting: Effects on mechanical properties of polypropylene/talc composites

This article deals with the effects of surface‐modified talc particles on mechanical properties of polypropylene (PP)/talc composites. These materials were prepared by injection molding of PP blended with different concentrations of nontreated and treated talc, under the same processing conditions. Differential thermal calorimetry and scanning electron microscopy were used to assess thermal properties and morphology of the final composites. The reinforcing effect of talc, either treated or nontreated surface, on PP is analyzed through the tensile properties as a function of the mineral content (0–10 wt%). Morphological structure of composites revealed that the talc treatment improved the particle dispersion and distribution within the PP matrix and enhanced the interfacial PP‐talc adhesion. The mechanical properties of these composites, especially the Young modulus, tensile strength and elongation at break, were found to be improved respect to PP‐untreated talc ones. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Biodegradable biocomposites from poly(butylene adipate‐co‐terephthalate) and miscanthus: Preparation,compatibilization, and performance evaluation

Miscanthus fibers reinforced biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) matrix‐based biocomposites were produced by melt processing. The performances of the produced PBAT/miscanthus composites were evaluated by means of mechanical, thermal, and morphological analysis. Compared to neat PBAT, the flexural strength, flexural modulus, storage modulus, and tensile modulus were increased after the addition of miscanthus fibers into the PBAT matrix. These improvements were attributed to the strong reinforcing effect of miscanthus fibers. The polarity difference between the PBAT matrix and the miscanthus fibers leads to weak interaction between the phases in the resulting composites. This weak interaction was evidenced in the impact strength and tensile strength of the uncompatibilized PBAT composites. Therefore, maleic anhydride (MAH)‐grafted PBAT was prepared as compatibilizer by melt free radical grafting reaction. The MAH grafting on the PBAT was confirmed by Fourier transform infrared spectroscopy. The interfacial bonding between the miscanthus fibers and PBAT was improved with the addition of 5 wt % of MAH‐grafted PBAT (MAH‐g‐PBAT) compatibilizer. The improved interaction between the PBAT and the miscanthus fiber was corroborated with mechanical and morphological properties. The compatibilized PBAT composite with 40 wt % miscanthus fibers exhibited an average heat deflection temperature of 81 °C, notched Izod impact strength of 184 J/m, tensile strength of 19.4 MPa, and flexural strength of 22 MPa. From the scanning electron microscopy analysis, better interaction between the components can be observed in the compatibilized composites, which contribute to enhanced mechanical properties. Overall, the addition of miscanthus fibers into a PBAT matrix showed a significant benefit in terms of economic competitiveness and functional performances. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45448.     

Mechanical and thermal properties of talc and calcium carbonate filled polypropylene hybrid composites

The main aim of this work was to study and compare the mechanical and thermal properties of hybrid polypropylene (PP) composites and single‐filler PP composites. With two main types of mineral fillers—calcium carbonate (CaCO₃) and talc—PP composites of different filler weight ratios (talc/CaCO₃) were compounded with a twin‐screw extruder and then injection‐molded into dumbbell specimens with an injection‐molding machine. Tensile, flexural, and impact tests were performed to determine and compare the mechanical properties of the hybrid and single‐filler PP composites. A synergistic hybridization effect was successfully achieved; the flexural strength and impact strength were highest among the hybrids when the PP/talc/CaCO₃ weight ratio was 70:15:15. The nucleating ability of the fillers and its effects on the mechanical properties were also studied with differential scanning calorimetry. Because of the influence of talc as the main nucleating agent, the hybrid fillers showed significant improvements in terms of the nucleating ability, and this contributed to the increase in or retention of the mechanical properties of the hybrid composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3327–3336, 2004