NiO/MgO整体式催化剂上甲烷部分氧化制备合成气

甲烷部分氧化制备合成气反应过程具有反应速率快、能耗低和H₂与CO物质的量比适用于合成甲醇及F-T合成等优点,是一种有希望替代传统水蒸汽重整的方法。研究在NiO/MgO蜂窝陶瓷整体式催化剂上的甲烷部分氧化过程,主要考察涂层载体、活性组分Ni含量、涂层载体前驱体、焙烧温度和还原温度对催化剂反应性能的影响。采用XRD、H₂-TPR和N2吸附等表征前驱体及其负载活性组分NiO后的晶相、还原特性和吸附性能。结果表明,采用浸渍法制备催化剂时,Mg(NO₃)₂为涂层载体MgO前驱体,在NiO负载质量分数20%、焙烧温度（500~600） ℃和还原温度750 ℃条件下制备的催化剂NiO/MgO-N性能较好,活性较稳定;以NiO/MgO-N为催化剂,在反应温度800 ℃、n(O₂)∶n(CH₄)＝0.5和空速9 723 h^-1条件下,CH₄转化率94.4%,H₂选择性99.9%,CO选择性92.9%。     

Ni/W-Al2O3催化剂在富氢气体中CO选择性甲烷化的研究

采用等体积浸渍法在Ni基催化剂上添加W助剂制备Ni/W-Al₂O₃催化剂，探究Ni负载量、W摩尔分数和焙烧温度对催化剂CO选择性甲烷化的影响。利用XRD、N₂-物理吸附、H₂-TPR、NH₃-TPD、CO₂-TPD、TEM等对催化剂进行表征。结果表明，有W的催化剂在低温下活性很差，不能提高活性。在Ni负载量为20%、W摩尔分数为0.05、焙烧温度为900℃、空速为4 800 h^-1的条件下，反应温度在207～339℃范围内，20%Ni/0.05W-Al₂O₃-900℃催化剂能使CO出口体积分数始终小于10μL/L,CH₄出口体积分数小于2%。     

Ni-Mn/Al2O3催化剂在浆态床中CO甲烷化催化性能

采用共浸渍法制备了Ni-Mn/Al₂O₃催化剂,考察了助剂Mn的含量对催化剂结构及浆态床CO甲烷化性能的影响。采用XRD、H₂-TPR、BET、TEM、H₂-化学吸附等表征对催化剂进行了测试分析,结果表明,Mn助剂的引入能够促进Ni物种在载体表面的分散,减弱Ni物种与载体的相互作用,降低催化剂的还原温度,提高催化剂的比表面积,减小活性金属Ni的晶粒尺寸。随着Mn含量的增加,Ni-Mn/Al₂O₃催化剂的甲烷化性能先升后降,其中以Mn含量为4%（质量分数）时的催化甲烷化性能最佳,添加过量的Mn导致活性组分Ni被部分覆盖,催化甲烷化性能下降。通过对16Ni4Mn/Al₂O₃催化剂样品的浆态床反应温度及反应压力的研究发现,当反应温度为280℃、反应压力为1.5 MPa时,催化剂样品16Ni4Mn/Al₂O₃的CO转化率及CH₄选择性分别达到96.2%和88.8%。     

基于MCM-41的镍基甲烷化催化剂活性与稳定性

采用浸渍法分别以MCM-41,Al₂O₃和SiO₂ 为载体制备了不同镍负载量的甲烷化催化剂,并在连续流动固定床反应装置上对其甲烷化催化活性进行了评价。研究结果表明,与Ni/Al₂O₃和Ni/SiO₂相比,相同镍负载量的Ni/MCM-41催化剂具有更好的催化活性。同时研究了Ni含量对于Ni/MCM-41催化剂催化活性的影响,发现随着Ni含量的增加,CO转化率和CH₄收率逐渐升高,并且在Ni含量大于10%（质量分数）以后趋于稳定。在n（H₂）：n（CO）=3：1、反应压力1.5 MPa、反应温度350℃及质量空速12000 ml·h^-1·g^-1的反应条件下,10%Ni/MCM-41催化剂CH₄选择性达到94.9%,CO转化率接近100%。在100 h催化活性稳定性试验中,10%Ni/MCM-41催化活性无明显下降,表现出良好的催化活性稳定性。采用X射线衍射（XRD）、氮气物理吸附（BET）、热重分析（TG）及氢气程序升温还原（H₂-TPR）等技术手段对催化剂进行了表征,结果表明Ni颗粒大小是影响Ni/MCM-41催化剂催化活性的主要因素。     

甲烷二氧化碳重整镍基催化剂的研究

采用浸渍法制备不同组成催化剂Ni-M/γ-Al₂O₃（M=Zr、Co、Mg、Nd）,通过固定床反应装置考察不同助剂、助剂含量和反应温度对催化剂活性的影响,并对催化剂进行X射线衍射表征。结果表明,14Ni-5Mg/γ-Al₂O₃的催化活性较好,随着反应温度的升高,甲烷转化率和CO收率均升高,反应温度升至800 ℃时,甲烷转化率达97.54%。采用共沉淀法制备载体、浸渍法制备的催化剂14Ni/MgO-Al₂O₃,在反应温度800 ℃、压力1.013 kPa、n(CO₂)∶n(CH₄)=1.2和催化剂用量0.5 g条件下,CO收率高于14Ni-5Mg/γ-Al₂O₃催化剂,但甲烷转化率略低。     

铈锆固溶体担载的镍催化剂对CO2甲烷化性能研究

采用共沉淀法制备了Ce_xZr_1-xO₂固溶体作为催化剂载体，采用柠檬酸络合法将镍负载于Ce_xZr_1-xO₂载体上得到Ni/Ce_xZr_1-xO₂催化剂，利用X射线衍射（XRD）、N₂吸附-脱附（N₂-BET）、程序升温脱附（TPD）、程序升温还原（TPR）等技术对催化剂进行表征，在常压微型固定床反应器上测试了CO₂甲烷化的性能，考察了n（Ce）/n（Zr）、镍含量对催化性能的影响。研究发现制备的催化剂具有优异的活性，在常压和空速15 000 mL·g^-1·h^-1条件下，反应温度200℃时，12% Ni/Ce_0.25Zr_0.75O₂催化剂（负载量为质量分数，下同）CO₂的转化率达74%，CH₄选择性为100%。12% Ni/Ce_0.25Zr_0.75O₂催化剂300 h的稳定性测试结果显示其具有较高的抗烧结性能。催化剂的优异活性归因于采用了新的负载方法--柠檬酸络合法负载活性组分镍，该法实现了镍的高分散和催化剂的大的比表面积。     

纤维状BPO4/SiO2催化剂的制备及其丙烷氧化脱氢性能

通过静电纺丝法制备了一种高温焙烧后具有纤维状结构的磷酸硼/二氧化硅（BPO₄/SiO₂）催化剂,并考察了BPO₄负载量和焙烧温度对该催化剂的结构和催化丙烷氧化脱氢性能的影响。研究发现焙烧过程使纤维直径减小。随着BPO₄负载量的增加,丙烷氧化脱氢活性增高。当BPO₄负载量为7%（质量分数）,焙烧温度为600℃时,BPO₄/SiO₂催化剂具有最佳的催化性能;在反应温度为480℃下,丙烷转化率和丙烯产率分别达到17.0%和13.0%,且催化剂稳定性良好。当焙烧温度较低时（550℃）,催化剂中的有机物分子未被除尽,导致烯烃的选择性偏低;当焙烧温度较高时（700℃）,SiO₂结构收缩紧密,抑制了活性相的暴露。由于纤维结构可暴露更多活性位点,该催化剂较相同条件下粉末状BPO₄催化剂有着更高的催化活性。     

甲烷干气重整（Ni/MgAl2O4）@SiO2催化剂的制备及抗积碳性能研究

采用烷基偶联剂水解法制备（Ni/MgAl₂O₄）@SiO₂催化剂,探究Ni、SiO₂质量分数对催化剂的甲烷干气重整（DRM）反应活性和抗积碳性能的影响。在常压、750℃、V（CH₄）∶V（CO₂）∶V（N₂）=5∶5∶1、GHSV=26 400 mL/(g_cat·h)条件下进行DRM反应,（10Ni/MgAl₂O₄）@5SiO₂催化剂表现出最好的反应性能,CH₄转化率为77%,CO₂转化率为90%。通过TEM、SEM等表征发现,SiO₂可以包覆在Ni/MgAl₂O₄催化剂表面,阻碍Ni晶粒团聚,增大催化剂的抗积碳性能。将该催化剂在严苛条件[V（CH₄）∶V（CO₂）∶V（N₂...     

负载型NiO-La2O3催化剂在CO2甲烷化反应中的研究

将二氧化碳转化为易于储存和运输的高热值燃料——甲烷,不仅可以缓解温室效应,也是解决能源短缺的有效途径。本文采用柠檬酸络合的等体积超声浸渍法制备一系列NiO-La₂O₃/SiO₂催化剂,其中镍和镧的摩尔比为1:1,并采用XRD、H₂-TPR表征技术对NiO-La₂O₃/SiO₂催化剂的结构和物化性质进行了研究。考察了NiO-La₂O₃的负载量对CO₂甲烷化反应性能的影响。结果表明,10%NiO-La₂O₃/SiO₂催化剂表现出最优的CO₂甲烷化反应性能,且在450℃时表现出最佳的反应活性,CO₂转化率和CH₄选择性分别为59.3%和60.8%。     

B2O3负载量对MoO3/CeO2-Al2O3耐硫甲烷化性能的影响

考察B₂O₃负载量对于MoO₃/CeO₂-Al₂O₃催化剂对耐硫甲烷化活性的影响,利用BET、XRD、TEM、NH₃-TPD等手段对催化剂进行了表征。结果表明,催化剂的耐硫甲烷化活性随B₂O₃负载量增加呈现先升高后降低的变化规律;当B₂O₃负载量为0.5%时,催化剂的耐硫甲烷化活性最高,CO转化率达到55%。结合表征分析,发现添加B₂O₃会影响催化剂载体的结构和表面酸度,从而影响活性组分的分散程度,进而影响MoO₃/CeO₂-Al₂O₃催化剂的耐硫甲烷化性能。催化剂的晶化程度太高或单位面积上的强酸量太多均不利于甲烷化反应;较好的活性组分分散度有利于催化剂甲烷化活性的提高。     

Influence of nickel distribution on properties of spherical catalysts for partial oxidation of methane to synthesis gas

Two kinds of Ni/Al₂O₃ catalysts, i.e., eggshell and uniform catalysts, were prepared by impregnation method using acetone and water solution of nickel nitrate, respectively, and their properties were investigated by means of EDS, XRD and TPR. Their catalytic performance in methane partial oxidation (POM) to synthesis gas was also evaluated. Because the partial oxidation of methane is a very fast reaction, the intra-particle diffusion was very remarkable. Due to nickel component distributing in the outer region of particles, the eggshell catalyst had higher effectiveness factor, which resulted in its better catalytic performance than the uniform one.     

Ni/ZrO2催化剂的制备及甲烷分步水蒸气重整反应性能

采用沉淀法制备了ZrO₂载体,进一步采用浸渍法制备了不同Ni负载量的Ni/ZrO₂催化剂。通过XRD、N₂物理吸附、H₂-TPR和H₂-TPD等表征手段对Ni/ZrO₂催化剂的物理结构和化学特性进行了研究,探讨了活性金属Ni物种的状态,并计算了Ni粒子的大小。随着Ni负载量的增加,Ni/ZrO₂催化剂的比表面积逐渐减小,金属Ni的分散度逐渐减小,Ni粒子尺寸逐渐增大,低温H₂脱附峰所占比例逐渐增大。当Ni负载量为10.2%（质量分数）时,Ni/ZrO₂催化剂上ZrO₂晶粒的平均尺寸和Ni粒子的尺寸大小均接近30nm。进一步考察了Ni/ZrO₂催化剂在甲烷分步水蒸气重整反应中的催化性能。结果表明,Ni负载量在一定范围内的Ni/ZrO₂催化剂对于甲烷分步水蒸气重整反应具有良好的催化性能,Ni负载量过高或过低均不利于甲烷的转化。当Ni负载量为10.2%时,载体ZrO₂粒子和金属Ni粒子尺寸匹配,Ni/ZrO₂催化剂表现出最佳的甲烷转化活性和稳定性。     

Ni Catalysts Supported on Mesoporous Nanocrystalline Magnesium Silicate in Dry and Steam Reforming Reactions

Mesoporous nanocrystalline MgSiO₃ with high surface area was synthesized by a hydrothermal method and employed as support in dry and steam reforming of methane. Ni/MgSiO₃ catalysts were prepared by an impregnation method and characterized by different techniques. N₂ adsorption analysis indicated that addition of nickel shifted the pore size distributions to smaller sizes. Temperature‐programmed reduction analysis revealed that a higher nickel loading enhanced the reducibility of the catalyst. The catalytic performance was improved with increasing the nickel content. The Ni/MgSiO₃ catalyst exhibited high stability in dry reforming but methane conversion declined with time‐on‐stream in the steam reforming reaction. Temperature‐programmed oxidation profiles of spent catalysts indicated that the high amount of carbon deposited on the catalyst surface in dry and steam reforming was assigned to whisker‐type carbon.     

Effect of calcination temperature of mesoporous nickel–alumina catalysts on their catalytic performance in hydrogen production by steam reforming of liquefied natural gas (LNG)

Mesoporous nickel–alumina (Ni–A-NS) catalysts prepared by a non-ionic surfactant-templating method were calcined at various temperatures for use in hydrogen production by steam reforming of liquefied natural gas (LNG). The effect of calcination temperature of nickel–alumina catalysts on their physicochemical properties and catalytic activity for steam reforming of LNG was investigated. Nickel oxide species were finely dispersed on the surface of Ni–A-NS catalysts through the formation of nickel aluminate phase. Reducibility, nickel surface area, and nickel dispersion of Ni–A-NS catalysts decreased with increasing calcination temperature. In the steam reforming of LNG, both LNG conversion and hydrogen composition in dry gas decreased with increasing calcination temperature of Ni–A-NS catalysts. Nickel surface area and reducibility of Ni–A-NS catalysts were well correlated with catalytic performance of the catalysts. Among the catalysts tested, Ni–A-NS700 (nickel–alumina catalyst calcined at 700 °C) with the highest nickel surface area and the highest reducibility exhibited the best catalytic performance.     

Preparation of Highly Active Nickel Catalysts Supported on Mesoporous Nanocrystalline γ‐Al2O3 for Methane Autothermal Reforming

Autothermal reforming (ATR) of methane was carried out over nanocrystalline Al₂O₃‐supported Ni catalysts with various Ni loadings. Mesoporous nanocrystalline γ‐Al₂O₃ powder with high specific surface area was prepared by the sol‐gel method and employed as support for the nickel catalysts. The prepared samples were characterized by X‐ray diffraction, Brunauer‐Emmett‐Teller, temperature‐programmed reduction, temperature‐programmed hydrogenation, and scanning electron microscopy techniques. It is demonstrated that the methane conversion increased with increasing in Ni content and that the catalyst with 25 wt % Ni exhibited the highest activity and a stable catalytic performance in the ATR process, with a low degree of carbon formation. Furthermore, the effects of the reaction temperature, the calcination temperature, the steam/CH₄ and O₂/CH₄ ratios, and the gas hourly space velocity on the catalytic performance of the 25 % Ni/Al₂O₃ catalyst were investigated.     

Synthesis of m-phenylenediamine from m-dinitrobenzene over silica-supported nickel catalyst

The liquid-phase hydrogenation of m-dinitrobenzene to m-phenylenediamine was studied over silica-supported nickel catalyst. The effects of Ni loading, calcination temperature, and reduction temperature on the physicochemical characteristics and activity of the catalyst were investigated by XRD, TEM, TPR, and activity tests. The results show that the silica-supported nickel catalysts exhibited high catalytic property, which depended on the particle size of Ni and the reduction degree of NiO. The optimal Ni loading, calcination temperature and reduction temperature of the catalyst for m-dinitrobenzene hydrogenation were found to be 20 wt%, 773 K in air and 723 K, respectively. Under this condition, 97.2% conversion of m-dinitrobenzene and 88.9% yield of m-phenylenediamine were obtained at 373 K and 2.6 MPa hydrogen pressure. The particle size of nickel species increased with the increase in Ni loading or calcination temperature. In addition, it was found that the catalyst could not be completely reduced at low reduction temperature, whereas high reduction temperature led to the sintering of Ni.     

MCM-41 supported PdNi catalysts for dry reforming of methane

A series of bimetallic PdNi catalysts supported on mesoporous MCM-41 with different Ni content (Ni/Si ratio of 0.2–0.4) was synthesized. The effect of Pd addition to Ni-containing catalysts as well as the effect of the Ni content on the surface and catalytic properties of the catalysts was studied. The samples were characterized using various techniques, such as energy-dispersive X-ray spectroscopy, N₂ adsorption–desorption isotherms, X-ray diffraction, thermogravimetric and differential analyses, X-ray photoelectron spectroscopy, high resolution transmission electron microscopy and temperature-programmed reduction. Reforming of methane with carbon dioxide was used as a test reaction. The results indicated that the addition of a small amount of Pd (0.5%) to Ni-containing catalysts leads to formation of small nano-sized, easy reducible NiO particles. Agglomeration of NiO as well as of metallic nickel phase over PdNi samples increased with increasing the Ni content. Formation of filamentous carbon over surface of spent monometallic Ni and bimetallic PdNi catalyst was observed. In spite of filamentous carbon deposition, the catalytic activity and stability of bimetallic PdNi catalysts are higher than those of monometallic Ni one. Within bimetallic system, the PdNi catalyst with Ni/Si ratio of 0.3 revealed the best performance and stability caused by presence of small nickel particles well dispersed on the catalyst surface.     

氢气高温还原制备的负载型镍基催化剂用于苯酚加氢的性能

通过等体积浸渍法分别将Ni(NO₃)₂、NiCl₂、NiSO₄ 3种镍前体浸渍于A1₂O₃或SiO₂载体上,然后通过H₂高温还原法制备了负载型镍基催化剂,考察了镍前体、载体种类、镍负载量、反应条件等对镍基催化剂苯酚加氢性能的影响。结果表明,对比3种镍前体,在H₂高温还原体系中Ni(NO₃)₂最容易被还原,制备的镍基催化剂苯酚加氢活性最高。SiO₂负载的镍基催化剂活性远高于γ-Al₂O₃催化剂。适宜的Ni负载量有助于活性组分的分散和催化活性的提高。镍基催化剂的苯酚加氢产物以环己醇为主,相对缓和的反应条件更容易生成环己酮。在非极性溶剂正庚烷或环己烷存在下,苯酚加氢反应速率远远高于极性溶剂水或乙醇存在下的结果,而且环己酮的选择性更高。     

甲烷部分氧化制合成气催化剂的研究进展

综述了甲烷部分氧化制合成气的研究意义和现状，从金属活性组分，载体效应，载量选择，助剂添加和制备方法等因素对催化剂活性的影响及研究进行了系统。结合本课题组的研究结果及文献报道，分析了Ni基催化剂的失活特性，并提出使用等离子体技术对Ni基催化剂进行改笥处理，以提高其催化稳定性的技术展望。