The function of zeolite on Pt autoreduction and dispersion in Pt/L and Pt/β catalysts

TPR, CO-FTIR and¹²⁹Xe NMR spectroscopic techniques were used to measure the distribution of platinum species after the calcination of Pt/L and Pt/ zeolites. Autoreduction which occurred in Pt/ zeolite was avoided in the channel of L zeolite. Pt particles dispersed well and exhibited excellent reactivity for the aromatization ofn-hexane in L zeolite.     

Solubilities of Cimaterol and Mabuterol in SF-CO2

The solubilities of two β-agonists, cimaterol and mabuterol, in supercritical carbon dioxide (SF-CO2) were measured by a recirculating method at temperatures of 40℃ and 60℃ and pressures between 9 MPa to 49 MPa.The compounds exhibit very limited solubilities in the range of 10^-5 to 10^-7 (mole fraction). Cimaterol has a higher solubility than that of mabuterol. The experimental data of solubility were correlated by four density-based models.The correlation accuracy highly depends on the system investigated, which is mainly determined by the density ranges and temperature.     

A calorimetric study of oxygen-storage in Pd/ceria and Pd/ceria–zirconia catalysts

Heats of adsorption were measured calorimetrically for O₂ adsorption on reduced Pd/alumina, Pd/ceria, and Pd/ceria–zirconia catalysts, all with 1 wt% Pd. Significantly more O₂ adsorbed on the ceria-containing catalysts due to oxidation of the support. For Pd/alumina, the heats were found to be between 180 and 220 kJ/mol, only slightly higher in magnitude than the heat of reaction for bulk oxidation of Pd. However, the heats of adsorption for both ceria and ceria–zirconia were also 200 kJ/mol, much lower than the heat of reaction for Ce₂O₃ oxidation to CeO₂, but in reasonable agreement with estimates from O₂ desorption studies on model ceria films. The implications of these results for understanding oxygen-storage properties on ceria-based catalysts are discussed.     

Synthesizing and characterizing the magnetic EDTA/chitosan/CeZnO nanocomposite for simultaneous treating of chromium and phenol in an aqueous solution

A new magnetic nanocomposite chitosan/EDTA/CeZnO(MEC-CeZnO) is synthesized as an efficient and eco-friendly bio-compound for the removal of chromium Cr(VI) metal ions and phenol organic matters from aqueous solutions. Nanocomposites are characterized using field emission scanning electron microscope, energy dispersive X-ray spectroscopy, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, diffuse reflection spectroscopy,...     

Soil aggregation and carbon and nitrogen stabilization in relation to residue and manure application in rice–wheat systems in northwest India

Soil organic matter (SOM), besides influencing carbon (C) transfer between soils and atmosphere, impacts soil functional ability and its response to environmental and anthropogenic influences. We studied the impact of continuous application of rice straw and farmyard manure (FYM) either alone or in conjunction with inorganic fertilizers on aggregate stability and distribution of C and nitrogen (N) in different aggregate fractions after 7 years of rice–wheat cropping on a sandy loam soil. Macroaggregates (>0.25 mm) constituted 32.5–54.5% of total water stable aggregates (WSA) and were linearly related (R ² = 0.69) to soil organic carbon content. The addition of rice straw and FYM significantly (P < 0.05) improved the formation of macroaggregates with a concomitant decrease in the proportion of microaggregates at all the three sampling depths (0–5, 5–10 and 10–15 cm). Macroaggregates had higher C and N density as compared to microaggregates. Application of rice straw and FYM improved C and N density in different aggregate sizes and the improvement was greatest in plots that received both rice straw and FYM each year. Application of FYM along with inorganic fertilizer resulted in a net C sequestration of 0.44 t ha⁻¹ in the plough layer after 7 years of rice–wheat cropping. Carbon sequestration was greater (1.53 t ha⁻¹) when both rice straw and FYM along with inorganic fertilizers were applied annually. It is concluded that addition of rice straw and FYM in rice–wheat system improves soil aggregation and enhances C and N sequestration in macroaggregates. This will help in sustainable rice–wheat productivity in the region.     

Sharkskin and oscillating melt fracture: Why in slit and capillary dies and not in annular dies?

The sharkskin and stick‐slip polymer extrusion instabilities are studied primarily as functions of the type of die geometry. Experimental observations concerning the flow curves, the critical wall shear stress for the onset of the instabilities, the pressure and flow rate oscillations, and the effects of geometry and operating conditions are presented for linear low‐density polyethylenes. It is found that sharkskin and stick‐slip instabilities are present in the capillary and slit extrusion. However, annular extrusion stick‐slip and sharkskin are absent at high ratios of the inside‐to‐outside diameter of the annular die. This observation also explains the absence of these phenomena in other polymer processing operations such as film blowing. These phenomena are explained in terms of the surface‐to‐volume ratio of the extrudates, that is, if this ratio is high, sharkskin and stick‐slip are absent. POLYM. ENG. SCI., 2008. © 2007 Society of Plastics Engineers     

Statistical fatigue strength evaluation and inelastic deformation generated during static and cyclic loading in Ce-TZP/alumina nanocomposite: Part 1—in air environment

The statistical fatigue strength evaluations of an intragranular type Ce-TZP/Al₂O₃ nanocomposite (Ce-TZP/A-N), such as its initial strength, static and cyclic fatigue lives, and its dispersion, were investigated in comparison to 3Y-TZP. The strength degradations during static and cyclic loading of Ce-TZP/A-N were fairly small, and the dispersions of the fatigue life were also quite small compared to those of 3Y-TZP, especially for the case of cyclic loading. In addition, fairly large inelastic deformations (converted strain ≈0.1–0.3%) were observed in the non-failure fatigued specimens after both static and cyclic loading. The amount of inelastic deformations was generally higher under the static loading than under cyclic loading, and increased with increasing the applied stress. In contrast, no inelastic deformation was identified for 3Y-TZP. By means of X-ray diffraction analysis, a good correlation between the amount of inelastic strain and the transformed monoclinic content was recognized for both static and cyclic loading.     

Fatigue and subcritical crack growth in ZrO2–bioglass ceramics

This work investigates the characteristics of ZrO₂ based ceramics (Y-TZP) doped with bioglass developed for dental prostheses. Powder mixtures composed of zirconia and 3 or 5 wt% of 3CaO·P₂O₅–SiO₂–MgO bioglass were sintered at 1300 °C for 2 h. The samples were characterized by their phase composition using X-Ray diffraction (XRD) and analysis of their microstructure by scanning electronic microscopy (SEM). Hardness and fracture toughness were evaluated using the Vickers indentation method, while bending strength and fatigue resistance were determined using the four-point bending testing. The mechanical properties indicate that the samples achieved high density under the applied sinter conditions. X-ray diffraction analysis revealed tetragonal ZrO₂ as a major crystalline phase. Hardness, fracture toughness and bending strength of the sintered samples containing 3% or 5% bioglass were 1167and 1134 HV, 6.3 and 6.1 MPa m^1/2 and 453 and 636 MPa, respectively. The fatigue results presented large scattering, which is attributed to a heterogeneous distribution of the secondary glassy phase in the zirconia matrix. The non-uniform dispersion of the glass may result in the formation of stress gradients, possibly responsible for crack initiation and their respective subcritical growth during fatigue testing. The fatigue limit determined was superior to stresses developed during mastication, turning its use in dental prostheses viable. Weibull statistics were applied on the fatigue results obtained at average stress levels of 255, 270 and 285 MPa in order to calculate the subcritical crack growth. A life expectancy of over 20 years under severe cyclic pressure conditions has been calculated.     

Ablation of C/SiC,C/SiC–ZrO2 and C/SiC–ZrB2 composites in dry air and air mixed with water vapor

C/SiC composites with different additives (ZrO₂ and ZrB₂) were fabricated by CVI and CVD and their oxidation and ablation properties at 1700–1800 °C were investigated. Two different ablation test conditions, dry air and air mixed with water vapor, are compared. The ablation test results are reviewed, the weight loss rates are presented and the corresponding micro-structures are investigated in detail. The results show that in dry air, the weight loss rate of C/SiC composites is greater than those with ZrO₂ and ZrB₂ additives. However, in air mixed with water vapor (5 wt%) to simulate the hygrothermal condition, the weight loss rates of these three composites all become relatively smaller. A model is proposed to predict the weight loss of C/SiC composites and it agrees well with the experimental data.     

Interactions in PEG/Aerosil® and PLA/Aerosil® composites described by IGC-determined Flory-Huggins χ 23 parameter

Nonsolvent Induced Phase Separation (NIPS) is among the most well-known methods for membrane fabrication in which the phase separation behavior of the polymer solution is one factor that governs the structure of the membrane ultimately obtained. In this study, phase separation behavior of the polyetherimide (PEI)-casting dope was investigated for different types of coagulants and nonsolvent additives. Cloud point data were obtained by the titration method on the ternary polyetherimide/solvent/coagulant diagram from a limited number of experiments. The whole cloud point curves were then drawn by calculation using the fitting parameters based on the linearized cloud point relation (LCP). In the first part, water, methanol, ethanol, glycerol, and acetic acid were used as the coagulants for the PEI/NMP solution. The cloud point curves obtained for the above coagulants indicated that water has the strongest coagulation power among them. In the second part, methanol, ethanol, glycerol, and acetic acid were used as nonsolvent additives to NMP in different (nonsolvent additive/NMP) mass ratios. The latter (NMP?+?nonsolvent additive) mixtures were then used as the solvents to prepare PEI/(NMP?+?nonsolvent additive) solutions. The cloud point data obtained for the above solutions using water as a coagulant indicated that the cloud point curves shift toward the polymer/solution axis as the (nonsolvent additive/NMP) mass ratio increases.

Horizontal gas and gas/solid jet penetration in a gas–solid fluidized bed

In this paper, the real time, dynamic phenomena of the three-dimensional horizontal gas and gas/solid mixture jetting in a 0.3 m (12 in) bubbling gas–solid fluidized bed are reported. The instantaneous properties of the shape of the jets and volumetric solids holdup are qualified and quantified using the three-dimensional electrical capacitance volume tomography (ECVT) recently developed in the authors’ group. It is found that the horizontal gas jet is almost symmetric along the horizontal axis during its penetration. As the jet width expands, the total volume of the gas jet increases. A mechanistic model is also developed to account for the experimental results obtained in this study. Comparison of jet penetration length and width between the model prediction and ECVT experiment shows that both the maximum penetration length and the maximum width of the horizontal gas jet increase with the superficial gas velocity. When the horizontal gas jet coalesces with a bubble rising from the bottom distributor, it loses its symmetric shape and can easily penetrate into the bed. For the horizontal gas/solid mixture jet penetration in the bed, the tail of the jet at the nozzle shrinks and the jet loses its jet shape immediately when the jet reaches its maximum penetration length, which are different from the characteristics exhibited by the gas jet. The solids holdup in the core region of the gas/solid mixture jet is higher than that in the gas jet. The penetration length of the horizontal gas/solid mixture jet is also larger than that of the gas jet.     

Selective CO oxidation over promoted Au/γ-Al2O3 catalysts in the presence of CO2 and H2O in the feed

In this work, the effect of promoter type (Mg, Mn, Ce, Co, Fe and Ni) on selective CO oxidation performance of Au/γ-Al₂O₃ was studied with the realistic feed stream containing CO₂ and H₂O. The effects of Au loading, promoter loading, reaction temperature and the feed composition were also investigated. It was found that MgO was the best promoter in the presence of CO₂ and H₂O, and 1.25 wt.% Mg was sufficient for promotion. The CO conversion decreased with the addition of CO₂ while the presence of H₂O had some positive effects.     

How green is green? Sampling and perception in assessing green seeds and chlorophyll in canola

Green seeds are used as a grading factor in estimating chlorophyll in canola and rapeseed in the Canadian and U.S.A. grading systems. This work examines the effect that sampling and perception have on the estimation of green seeds as well as the effect that sampling has on the determination of chlorophyll. Individual seed analysis indicated that in order to be considered as green, seeds needed to contain between 200 and 400 mg/kg chlorophyll. Variation due to binomial sampling played a predominant role in the error in determining the green seed levels in canola. Sampling of large numbers of seeds, as in the loading of export shipments, reduced the error. Binomial sampling also contributed to the error in chlorophyll determination even with sample sizes as large as 500. Differences in perception of green also were noted between individuals with coefficients of variation as high as 50% at the 1% green seed level. The combination of perception error and sampling error may result in samples of 1,000 seeds drawn from a mass with 2% green seeds having green seed counts ranging from 0.96 to 3.04%, 19 times out of 20.     

Crystallization and melting behavior of polypropylene in β-PP/polyamide 6 blends containing PP-g-MA

In this research, we used a twin-screw extruder to melt and blend PP-g-MA compatibilizer with β-polypropylene (PP)/polyamide 6 (PA6). The influences of the PA6 and PP-g-MA contents in PP/PA6 blends on crystallization and melting behavior of PP phase and morphology were investigated. The results showed that, when PP-g-MA copolymer was added to the β form of nucleated PP/PA6 blends, the anhydride groups in PP-g-MA and PA6 terminal amine groups react to form PP-g-PA graft copolymer in a two-phase interface. This reduces the interfacial tension, improves the interfacial adhesion, and reduces the size of PA6 domains in the blend. The generated PP-g-PA graft copolymer wrapped PA6 phase and buried the anhydride groups of PP-g-MA. When the proportion of PP-g-MA and PA6 was between 0.5 and 0.75, there was no longer interfering to the formation of β-crystals in the PP phase. The content of β-crystal of PP phase in blends was found to reach as large as 85.9%.     

Structure–property–processing relationships in chemically modified LDPE and LDPE/LLDPE blend

The properties of low-density polyethylene (LDPE) and its blend with linear low-density polyethylene LDPE : LLDPE (75 : 25) modified with varying concentrations of dicumyl peroxide (DCP) were compared. Chemical modification was carried out in a Brabender plasticorder under set conditions of temperature, rotor speed, and time. The results are reported in terms of the type of polyethylene used, concentration of DCP, mixing torque, temperature and time on the processing, and mechanical and physical properties of the modified samples. Interpretation of the results is given in terms of gel contents which relate to the three-dimensional network structure of polyethylene. The modified blend forms a denser network structure and, hence, better product properties relative to that of modified LDPE, indicating the influence of LLDPE in increasing the rate and extent of crosslinking on blending with LDPE. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:789–797, 1998     

Measurement and model of density,viscosity, and hydrogen sulfide solubility in ferric chloride/trioctylmethylammonium chloride ionic liquid

The density and viscosity of ferric chloride/trioctylmethylammonium chloride ionic liquid(rFeCl₃/[A336]Cl) with different molar ratios(r=0.1–0.8) of FeCl₃ to [A336]Cl were measured at temperatures from 313.15 to 358.15 K and atmospheric pressure.The density and viscosity data were fitted by the relevant temperature variation equations,respectively.The variation of density and viscosity with temperature and r was obtained.The solubility of rFeCl₃/[A336]Cl to H     

Hydrogen-bond mediated and concentrate-dependent NaHCO3 crystal morphology in NaHCO3–Na2CO3 aqueous solution: Experiments and computer simulations

Adding Na₂CO₃ to the NaHCO3cooling crystallizer, using the common ion effect to promote crystallization and improve product morphology, is a new process recently proposed in the literature. However, the mechanism of the impact of Na₂CO₃ on the crystal morphology is still indeterminate. In this work, the crystallization of NaHCO₃ in water and Na₂CO₃ –NaHCO₃ aqueous solution was investigated by experiments and ...     

Output of Petroleum and Chemical Products in China in March 2005

ProdUCt MarChoutPUt Growth over000 tons Mar.,2004%January to MarchOutPut Growth over same000 tons Period of 2004,%5000256060605080﹁匆4040沙382,21. 44731__“_ _12 23,每--一-卜万550.515乐}O2030卯6010704800成27 八乙啥J.”21一7.308070…的O斗﹁2峨1朽‘娜器叩50﹁加一印性石怡拒 4129.71870访砧7.只钟生碑归事瞬_j使6 910 5*OQ~牛李_40 2.80一52031_6021.50一氏牛O_490一7.901李40夕汤6尸etr01eo爪bit自巾碑的OO一勺﹃二︺LPGCOke冷以furi杏aci诊(c峥nta)丽牙浮p归多日{笋口动53318.伯由认〕黔燕薰井鞘3621070…     

Output of Petroleum and Chemical Products in China in February 2005

ProdUCtFebruary outPut000 tonSGrOWth OVefFeb.,2004% January to February outPut Growth over same000 tons Period of 2004,%Crude Coa!CrUde 011Natural gas(billion m3)Pyrite(eontaining 35%sulfur)phosPhorus ore(Containing 30%P205)CrUde SaltPaPer PulP0 11 Proeessed GaS0line Ke「osone 0 iese! Lubrjcatingoils Fuel 0115Petroleumb计umeoLPGCO油Su!furie aeid(containing 100%H2s04)12202 .7015.30一1 .10 7 .10 5 .00 0 .80 930 2 .10 7,50一158010.9033一8018.5070 00 30 20 20 90 50806 1 4 9 2 6 00…     

Hemicellulose in corn straw:Extracted from alkali solution and produced 5-hydroxymethyl furfural in HCOOH/HCOONa buffer solution☆

Hemicellulose in corn straw is a group of complex heteropolysaccharides which are composed of different sugar units, including mannans, xylans, arabinans and galactans. This study developed a simple and practical process for production of 5-hydroxymethyl furfural(HMF) using hemicellulose that was extracted from corn straw. In the hemicellulose degradation process HCOOH/HCOONa was used as buffer solution, and the optimum conditions for maximum HMF yield were explored. Various extraction conditions including NaOH concentration, reaction time,temperature, solid-to-liquid ratio and precipitant were tested for hemicellulose obtaining, giving the optimum condition of 55 °C, 4 h, solid-to-liquid ratio of 1:10, 1.5 mol·L~(-1) NaOH solution and ethanol as precipitant with the yield of 34.16%. Dehydration of hemicellulose under HCOOH/HCOONa buffer solution process, using solution medium of pH = 0.8 hydrolyzed hemicellulose in corn straw at 190 °C after 190 min and 82% of HMF yield was achieved.