Effect of clay type and polymer matrix on microstructure and tensile properties of PLA/LLDPE/clay nanocomposites

Polylactide (PLA)/linear low‐density polyethylene (LLDPE), (PLA/LLDPE), blends and nanocomposites were prepared by melt mixing process with a view to fine tune the properties. Two different commercial‐grade nanoclays, Cloisite® 30B (30B) and Cloisite® 15A (15A) were used. A terpolymer of ethylene, butylacrylate (BA) and glycidylmethacrylate (GMA) was used as a reactive compatibilizer. The influence of type of clay on the morphology and mechanical properties of two PLA‐rich and LLDPE‐rich blend systems was studied. Morphological analysis using X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy revealed that the organoclay layers were dispersed largely at the interface of PLA/LLDPE. Decreasing the PLA content changed the morphology from droplet‐in matrix to coarse co‐continuous. In comparison with 30B, due to less affinity of 15A towards compatibilizer and PLA phase, the reduction of the size of dispersed phase was less than that of the equivalent 30B composites. The mechanical results demonstrated that the composites containing both types of organoclay exhibited higher modulus but lower elongation and tensile strength as compared to the neat blends. The injection molded nanocomposites were shown to have the sequential fracture behavior during tensile test. The tensile testing results on the neat blends and nanocomposites showed significant increase in elongation at break and decrease in the modulus as compared with the neat PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 749‐758, 2013     

Effect of Blending Procedure on Tensile and Degradation Properties of Toughened Biodegradable Poly(lactic acid) Blend with Poly(trimethylene terephthalate) and Reactive Compatibilizer

This research focuses on brittleness improvement of biodegradable poly(lactic acid) (PLA) by reactive melt blending with poly(trimethylene terephthalate) (PTT). First, PLA is simultaneously blended with PTT and a reactive compatibilizer, poly(ethylene‐co‐glycidyl methacrylate) (PEGMA), (one‐step blending procedure). In the PLA/PTT/PEGMA blend, PEGMA mainly disperses in the PLA matrix phase, and the blend shows unimproved tensile properties. To increase the reaction between PTT and PEGMA, PEGMA is sequentially blended with PTT then PLA (two‐step blending procedure). This procedure is effective in drastically enhancing elongation at break of the blend. The strain at break of the blend formed by two‐step blending is significantly improved because the blending procedure affects the blend morphology. PLA‐g‐PEGMA‐g‐PTT graft copolymer is formed at the interface between PLA and PTT during reactive melt blending with PEGMA when the two‐step blending procedure is employed as a blending method which is confirmed by Fourier transform infrared spectroscopy and viscosity measurement. Such features bring about craze formation during tensile test and this is the reason why the toughening is achieved by the two‐step blending procedure.     

Poly(lactic acid)/low‐density polyethylene blends and its nanocomposites based on sepiolite

Poly(lactic acid) (PLA) nanocomposite ternary blends based on unmodified sepiolite were prepared by melt blending using a corotating twin‐screw extruder. Two grafted polymers were used as compatibilizer agents, in an effort to increase the PLA tensile toughness. The influence of incorporating a low‐cost commodity low‐density polyethylene, as dispersed phase to the composites on thermal degradation, and rheological and tensile properties was studied. The morphology of the blends and composites was determined through transmission and scanning electron microscopy techniques. Results showed that the compatibilized blends prepared without clay have higher thermal degradation susceptibility and tensile toughness than those prepared with sepiolite and significant changes in complex viscosity and melt elasticity values were observed between them. The nanocomposite blends exhibited similar thermal degradation, lower tensile strength, and Young's modulus values and increased elongation at break and tensile toughness, complex viscosity, and storage modulus compared with those of the nanocomposite of PLA. These results are related to the clay dispersion, to the type of morphology of the different blends, to the localization of the sepiolite in the different phases, the thermomechanical degradation of the PLA matrix phase during melt blending and the grafting degree of the compatibilizers used. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Tailoring morphology to improve the gas‐barrier properties of thermoplastic polyurethane/ethylene‐vinyl alcohol blends

The morphology and helium‐barrier properties of thermoplastic polyurethane (TPU)/ethylene‐vinyl alcohol (EVOH) blends with and without dicumyl peroxide (DCP) were investigated by melting blending. A lamellar dispersion of EVOH with good helium‐barrier properties was observed in the TPU matrix with DCP. The evolution of the morphology of the blends is mainly related to the variation of the viscosity ratio between the dispersed phase and the matrix phase. Compared with pure TPU, lamellar morphology increased the helium‐barrier properties of the TPU/EVOH (60/40) blend by as much as 10‐fold. We also explored the effects of composition, DCP content, and blending sequence on the morphology and helium‐barrier properties of the TPU/EVOH blends. The morphology of the blends ranged from a droplet‐matrix to a lamellar structure. We determined the optimum amount of DCP to improve the helium barrier of the blends. The helium‐barrier properties of the blends prepared by direct blending were superior to those of the blends prepared by two‐segment blending, and the blends prepared by direct blending exhibited a well‐developed lamellar morphology. We compared the permeability of the samples with the theoretical results to explain the relationship between morphology and helium‐barrier properties. POLYM. ENG. SCI., 56:922–931, 2016. © 2016 Society of Plastics Engineers     

Rheological behavior of polyester blend and mechanical properties of the polypropylene–polyester blend fibers

The article deals with method of preparation, rheological properties, phase structure, and morphology of binary blend of poly(ethylene terephthalate) (PET)/poly(butylene terephthalate) (PBT) and ternary blends of polypropylene (PP)/(PET/PBT). The ternary blend of PET/PBT (PES) containing 30 wt % of PP is used as a final polymer additive (FPA) for blending with PP and subsequent spinning. In addition commercial montane (polyester) wax Licowax E (LiE) was used as a compatibilizer for spinning process enhancement. The PP/PES blend fibers containing 8 wt % of polyester as dispersed phase were prepared in a two‐step procedure: preparation of FPA using laboratory twin‐screw extruder and spinning of the PP/PES blend fibers after blending PP and FPA, using a laboratory spinning equipment. DSC analysis was used for investigation of the phase structure of the PES components and selected blends. Finally, the mechanical properties of the blend fibers were analyzed. It has been found that viscosity of the PET/PBT blends is strongly influenced by the presence of the major component. In addition, the major component suppresses crystallinity of the minor component phase up to a concentration of 30 wt %. PBT as major component in dispersed PES phase increases viscosity of the PET/PBT blend melts and increases the tensile strength of the PP/PES blend fibers. The impact of the compatibilizer on the uniformity of phase dispersion of PP/PES blend fibers was demonstrated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4222–4227, 2006     

Synthesis and characterization of TPO-PLA copolymer and its behavior as compatibilizer for PLA/TPO blends

A thermoplastic polyolefin elastomer-graft-polylactide (TPO-PLA) was prepared by grafting polylactide onto maleic anhydride-functionalized TPO (TPO-MAH) in the presence of 4-dimethylaminopyridine (DMAP). The characterization of the TPO-PLA copolymers was conducted by FT-IR and ¹H NMR. The effects of reaction temperature and concentration of DMAP on the reactivity of graft polymerization were investigated by FT-IR, which revealed that a high reaction temperature and a high DMAP concentration are associated with dramatic depolymerization of PLA and reduction of steric hindrance effect in the graft reaction. A Molau test, SEM observations of cyro-fractured surface morphology and particle size analysis of PLA/TPO blend system demonstrate that this new copolymer, acting as a premade compatibilizer, significantly improved the compatibility of the PLA/TPO blends. As the concentration of TPO-PLA copolymer increased, elongation at break and tensile toughness increased with compatibilizer concentration up to 2.5 wt%, beyond which it declined, but TPO-PLA copolymer did not affect the tensile strength or modulus. The effect of the chemical composition of the TPO-PLA copolymer on the compatibilization efficiency and mechanical properties of the PLA/TPO blends was examined by altering the number of grafting sites and concentration of DMAP, suggesting that DMAP concentration dominated the properties of the ternary blend system. Two compatibilizers, TPO-MAH and TPO-PLA, were used to compatibilize the PLA/TPO blend; the results suggested that TPO-PLA was more efficient in reducing the interfacial tension between the two immiscible polymers and in improving the mechanical properties of PLA/TPO blending specimens.     

In situ compatibilization of polylactide/thermoplastic polyester elastomer blends using a multifunctional epoxide compound as a processing agent

In situ compatibilized poly(lactic acid)/thermoplastic polyester elastomer (PLA/TPEE) (80/20) blends are prepared by using multifunctional epoxide oligomer (coded as ADR) as a reactive modifier. Experiments such as torque, melt mass flow rate (MFR), SEM, DSC and tensile test were conducted to characterize properties of the PLA/TPEE/ADR blends. In situ reactions between PLA, TPEE and ADR were researched using a lab torque rheometer. It was proposed that ADR may initiate a variety of chain extension/branching reactions between PLA and TPEE under mixing process. In particular, the formed copolymer PLA‐ADR‐TPEE could be viewed as an in situ compatibilizer to improve the compatibility of PLA and TPEE. As expected, the value of MFR decreased greatly with increasing the ADR addition. The morphology reveals that interface adhesion of PLA/TPEE blend was enhanced with the incorporation of ADR, which led to a reduction in TPEE domain size. Moreover, tensile ductility of PLA/TPEE (80/20) blend was improved greatly by addition of the reactive modifier, e.g. the elongation at break was increased from 53% to the maximum value of 213% with addition of 1.2 phr ADR. The toughening effect can be explained by crazing with shear yielding mechanism. Attempts were made to produce ductile films from these PLA/TPEE/ADR blends by using extrusion blowing method. Effect of ADR on blowing stability and tensile property of these blends was investigated. Improvement on blowing stability and tensile ductility of PLA/TPEE/ADR films also shows that ADR is an efficiently reactive compatibilizer, as well as a viscosity enhancer for PLA/TPEE blends. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43424.     

聚乳酸微纳复合泡孔的结构与性能研究

通过熔融共混制备聚乳酸（PLA）/聚（己二酸丁二酯?对苯二甲酸丁二酯）（PBAT）共混物。以环氧扩链剂（CE）为相容剂，研究了CE含量对共混物的流变行为、结晶行为的影响，并研究了CE含量为5份的共混物在冷结晶温度下的发泡行为以及泡沫的拉伸性能。结果表明，共混体系的相容性、结晶速率随着CE含量的增加而增加、可发性提高，在添加了5份CE的共混物中得到了微纳复合泡孔，泡孔密度达到10¹³ 个/cm³，相对于PLA泡沫，共混物泡沫的断裂伸长率提高了40 %。     

Synthesis of silane‐grafted ethylene vinyl acetate copolymer and its application to compatibilize the blend of ethylene‐propylene‐diene copolymer and silicone rubber

Vinyltrimethoxysilane‐grafted ethylene vinyl acetate copolymer (EVA‐g‐VTMS) was synthesized and applied to compatibilize ethylene‐propylene‐diene copolymer (EPDM)/methyl vinyl silicone rubber (MVQ) blends. The silane‐grafting was successfully proved by differential scanning calorimetry, FTIR spectroscopy and XPS spectroscopy. The additive amount of the compatibilizer (EVA‐g‐VTMS) was optimized to be 10 phr (parts per hundred of rubber in weight) based on analysis of scanning electron microscopy, mechanical properties, aging properties, dynamic mechanical properties, rheological properties and thermal properties. Compared with the blend without EVA‐g‐VTMS, results show that the blend with 10 phr of EVA‐g‐VTMS exhibits the finest morphology. Tensile strength, elongation at break, modulus at 100% elongation, tear strength and TE index increase by 82.5%, 16.9%, 60.0%, 40.9%, and 41.9%, respectively. Dynamic mechanical analysis reveals storage modulus increase and glass transition temperatures of EPDM and MVQ move closer to each other. Rheological analysis shows a decrease in complex modulus and complex viscosity, and the processibility of the blend was improved. Furthermore, thermogravimetric analysis shows enhancement of thermal stability. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers     

The Use of Ethylene/Propylene Copolymers as Compatibilizers for Recycled Polyolefin Blends

Compatibilizing effects of ethylene/propylene (EPR) diblock copolymers on the morphology and mechanical properties of immiscible blends produced from recycled low‐density polyethylene (PE‐LD) and high‐density polyethylene (PE‐HD) with 20 wt.‐% of recycled poly(propylene) (PP) were investigated. Two different EPR block copolymers which differ in ethylene monomer unit content were applied to act as interfacial agents. The morphology of the studied blends was observed by scanning‐ (SEM) and transmission electron microscopy (TEM). It was found that both EPR copolymers were efficient in reducing the size of the dispersed phase and improving adhesion between PE and PP phases. Addition of 10 wt.‐% of EPR caused the formation of the interfacial layer surrounding dispersed PP particles with the occurrence of PE‐LD lamellae interpenetration into the layer. Tensile properties (elongation at yield, yield stress, elongation at break, Young's modulus) and notched impact strength were measured as a function of blend composition and chemical structure of EPR. It was found that the EPR with a higher content of ethylene monomer units was a more efficient compatibilizer, especially for the modification of PE‐LD/PP 80/20 blend. Notched impact strength and ductility were greatly improved due to the morphological changes and increased interfacial adhesion as a result of the EPR localization between the phases. No significant improvements of mechanical properties for recycled PE‐HD/PP 80/20 blend were observed by the addition of selected block copolymers.     

Studies on the rheological,phase morphologic,thermal and mechanical properties of poly(trimethylene terephthalate)/ethylene propylene diene monomer copolymer grafted with maleic anhydride/metallocene polyethylene blends

The rheological, phase morphologic, thermal and mechanical properties of poly (trimethylene terephthalate)/metallocene polyethylene (PTT/mPE) blends in the presence of ethylene propylene diene monomer copolymer grafted with maleic anhydride (EPDM-g-MAH) as compatibilizer are studied by means of a capillary rheometer, scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). Results suggest that the compatibility of PTT/mPE blends is improved greatly after the addition of a compatibilizer. The radius of the dispersed phase in the system decreases greatly when the compatibilizer is added into the blend. When the amount of compatibilizer exceeds 8 wt-%, the size of dispersed phase becomes larger again. This phenomena could be attributed to the higher viscosity of the EPDM-g-MAH phase, which is dispersed more difficulty in the PTT phase of lower viscosity, thus the mixing efficiency is apparently decreased during the melt blending process. Moreover, the melt viscosity of the blend reaches the maximal value in case of 4 wt-% compatibilizer content, above which it would decrease again. This result is associated with the generation of more and bigger dispersed phase inside the bulk phase, thus the grafting efficiency at the interface is decreased, which could result in lower viscosity. The DSC results suggest that the mPE component shows a nucleating effect, and could increase the overall degree and rate of PTT crystallization, while the addition of a compatibilizer might slightly diminish these effects. In addition, the blend with 4 wt-% compatibilizer shows the best thermal stability. Furthermore, the Izod impact strength and the tensile strength at room temperature of the blend are also markedly improved by the addition of a 4–8 wt-% compatibilizer.     

Rheology‐morphology correlation in PET/PP blends: Influence of type of compatibilizer

Rheological and morphological properties of melt processed poly(ethylene terephthalate) (PET)/polypropylene (PP) blends are presented. Two types of compatibilizer namely, PP‐g‐MA <MA= maleic anhydtide> and Elvaloy PTW, an n‐butyl acrylate glycidyl methacrylate ethylene terpolymers, were incorporated at different levels to the PET/PP blend system. Scanning electron microscopy revealed that the dispersed particle sizes were smaller in PET‐rich blends than PP‐rich blends. With increasing compatibilizer level, the refinement of morphology was observed in both the systems. However, the blends compatibilized with PTW showed a more refined (smaller) particle size, and at high PTW content (10 wt%), the morphology changed towards monophasic. The significant changes in morphology were attributed to the highly reactive nature of PTW. Investigation of rheological properties revealed that the viscosity of the PET/PP blends followed typical trends based on mixing rule, which calculates the properties of blends based on a linear average. Incorporation of PP‐g‐MA into the blends resulted in a negative deviation in the viscosity of the system with respect to that of the neat blend. With increasing PP‐g‐MA level, the deviation became more pronounced. Although incorporation of the compatibilizer into the PET/PP blends refined the morphology, it led to a drastic drop of viscosity, which could be attributed to inherently lower molecular weight of the compatibilizer. In the case of the blends compatibilized by PTW, a strong positive deviation in rheological properties was observed that confirmed the stronger interaction between the blend components due to reactive compatibilization process, which led to the more refined morphology in this series of blends. J. VINYL ADDIT. TECHNOL., 19:25–30, 2013. © 2013 Society of Plastics Engineers     

Study on the effect of dispersion phase morphology on porous structure of poly (lactic acid)/poly (ethylene terephthalate glycol-modified) blending foams

A methodology for blending foam of poly (lactic acid) (PLA)/poly (ethylene terephthalate glycol-modified) (PETG) was proposed. PLA/PETG blends were prepared through a melt blending method, using multiple functionality epoxide as reactive compatibilizer. The effects of blending ratio and compatibilizer content on the dispersion morphology, molecular structure, mechanical properties, and rheological behavior of PLA/PETG blends were studied. Then PLA/PETG blends were foamed using supercritical CO₂ as physical blowing agent, and their porous structure, pore size, as well as pore density were investigated. The results showed that the mechanical properties and rheological parameters such as melt strength and melt elasticity, as well as the porous structure of the foams dispersion morphology of PLA/PETG blends were affected strongly. The melt elasticity of PLA/PETG blends increased with increasing compatibilizer content. Dispersion phase morphology of PLA/PETG blends also had a significant effect on the pore density of all the samples. The results indicated that homogeneous and finer porous morphology of PLA/PETG foams with high expansion ratio could be achieved with a proper content of compatibilizer in the blends.     

Studies on the rheological,phase morphologic,thermal and mechanical properties of poly(trimethylene terephthalate)/ethylene propylene diene monomer copolymer grafted with maleic anhydride/metallocene polyethylene blends

The rheological, phase morphologic, thermal and mechanical properties of poly(trimethylene terephthalate)/metallocene polyethylene (PTT/mPE) blends in the presence of ethylene propylene diene monomer copolymer grafted with maleic anhydride (EPDM-g-MAH) as compatibilizer are studied by means of a capillary rheometer, scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). Results suggest that the compatibility of PTT/mPE blends is improved greatly after the addition of a compatibilizer. The radius of the dispersed phase in the system decreases greatly when the compatibilizer is added into the blend. When the amount of compatibilizer exceeds 8 wt-%, the size of dispersed phase becomes larger again. This phenomena could be attributed to the higher viscosity of the EPDM-g-MAH phase, which is dispersed more difficulty in the PTT phase of lower viscosity, thus the mixing efficiency is apparently decreased during the melt blending process. Moreover, the melt viscosity of the blend reaches the maximal value in case of 4 wt-% compatibilizer content, above which it would decrease again. This result is associated with the generation of more and bigger dispersed phase inside the bulk phase, thus the grafting efficiency at the interface is decreased, which could result in lower viscosity. The DSC results suggest that the mPE component shows a nucleating effect, and could increase the overall degree and rate of PTT crystallization, while the addition of a compatibilizer might slightly diminish these effects. In addition, the blend with 4 wt-% compatibilizer shows the best thermal stability. Furthermore, the Izod impact strength and the tensile strength at room temperature of the blend are also markedly improved by the addition of a 4 8 wt-% compatibilizer.     

环氧类增容剂反应增容PLA/PBAT共混体系的研究

以环氧类增容剂(REC)为增容剂,采用双螺杆挤出机熔融共混制备聚乳酸(PLA)/聚对苯二甲酸己二酸丁二醇酯(PBAT)共混物。研究了增容剂对共混体系微观结构、力学性能和热性能的影响。结果表明,添加适量REC可以提高PLA与PBAT的相容性,改善PLA/PBAT共混体系的综合力学性能;REC用量为1.4份时共混体系呈现出良好的相容性,此时共混物冲击强度由268 kJ/m2增加到621 kJ/m2、断裂伸长率提高由222 %增加到357 %。     

Poly(ethylene‐graft‐ethylene oxide) (PE‐PEO) and poly(ethylene‐co‐acrylic acid) (PEAA) as compatibilizers in blends of LDPE and polyamide‐6

In a blend of two immiscible polymers a controlled morphology can be obtained by adding a block or graft copolymer as compatibilizer. In the present work blends of low‐density polyethylene (PE) and polyamide‐6 (PA‐6) were prepared by melt mixing the polymers in a co‐rotating, intermeshing twin‐screw extruder. Poly(ethylene‐graft‐polyethylene oxide) (PE‐PEO), synthesized from poly(ethylene‐co‐acrylic acid) (PEAA) (backbone) and poly(ethylene oxide) monomethyl ether (MPEO) (grafts), was added as compatibilizer. As a comparison, the unmodified backbone polymer, PEAA, was used. The morphology of the blends was studied by scanning electron microscopy (SEM). Melting and crystallization behavior of the blends was investigated by differential scanning calorimetry (DSC) and mechanical properties by tensile testing. The compatibilizing mechanisms were different for the two copolymers, and generated two different blend morphologies. Addition of PE‐PEO gave a material with small, well‐dispersed PA‐spheres having good adhesion to the PE matrix, whereas PEAA generated a morphology characterized by small PA‐spheres agglomerated to larger structures. Both compatibilized PE/PA blends had much improved mechanical properties compared with the uncompatibilized blend, with elongation at break (ε_b) increasing up to 200%. Addition of compatibilizer to the PE/PA blends stabilized the morphology towards coalescence and significantly reduced the size of the dispersed phase domains, from an average diameter of 20 μm in the unmodified PE/PA blend to approximately 1 μm in the compatibilized blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2416–2424, 2000     

Morphology and properties of the biosourced poly(lactic acid)/poly(ethylene oxide‐b‐amide‐12) blends

Biosourced poly(lactic acid) (PLA) blends with different content of poly(ethylene oxide‐b‐amide‐12) (PEBA) were prepared by melt compounding. The miscibility, phase structure, crystallization behavior, mechanical properties, and toughening mechanism were investigated. The blend was an immiscible system with the PEBA domains evenly dispersed in the PLA matrix. The PEBA component suppressed the nonisothermal melt crystallization of PLA. With the addition of PEBA, marked improvement in toughness of PLA was achieved. The maximum for elongation at break and impact strength of the blend reached the level of 346% and 60.5 kJ/m², respectively. The phase morphology evolution in the PLA/PEBA blends after tensile and impact tests was investigated, and the corresponding toughening mechanism was discussed. It was found that the PLA matrix demonstrates obvious shear yielding in the blend during the tensile and impact tests, which induced energy dissipation and therefore lead to improvement in toughness of the PLA/PEBA blends. POLYM. COMPOS., 2013. © 2012 Society of Plastics Engineers     

A comparative study of poly(l‐lactide)‐block‐poly(ϵ‐caprolactone) six‐armed star diblock copolymers and polylactide/poly(ϵ‐caprolactone) blends

This paper deals with the synthesis of a series of six‐armed star diblock copolymers based on poly(l ‐lactide) (PLLA) and poly(?‐caprolactone) (PCL) by ring‐opening polymerization using stannous octoate as catalyst and the preparation of polylactide (PLA)/PCL linear blends using a solution blending technique, while keeping the PLA‐to‐PCL ratio comparable in both systems. The thermal, rheological and mechanical properties of the copolymers and the blends were comparatively studied. The melting point and the degree of crystallinity were found to be lower for the copolymers than the blends due to poor folding property of star copolymers. Dynamic rheology revealed that the star polymers have lower elastic modulus, storage modulus and viscosity as compared to the corresponding blends with similar composition. The blends show two‐phase dispersed morphology whereas the copolymers exhibited microphase separated morphology with elongated (worm‐like) microdomains. The crystalline structures of the copolymers were characterized by larger crystallites than their blend counterparts, as estimated using Sherrer's equation based on wide‐angle X‐ray diffraction data. © 2016 Society of Chemical Industry     

Development of biodegradable PLA/PBT nanoblends

Poly(lactic acid)/poly(butylene terephthalate) (PLA/PBT) blends with 3, 5, and 10 wt % of PBT were produced in a twin‐screw extruder, with the addition of ethylene–glycidyl methacrylate copolymer as compatibilizer. An uncompatibilized PLA/PBT blend with 5 wt % of PBT was prepared for comparison studies. The epoxy reactive groups in the compatibilizer allowed modification of the interfacial tension in the blends and reduced the PBT dimensions. The crystallinity of the blends was studied, and its influence on mechanical properties was analyzed. Tensile tests showed an increase in strain at break from 3% for neat PLA to 49% for PLA with 3 wt % PBT, while the tensile modulus dropped from 3.59 GPa to 3.35 GPa for the same samples. Izod results showed a transition from a brittle behavior of PLA to a ductile one for compatibilized blends. These results indicate that the nanometer‐size dispersed phase was effective in changing the deformation behavior of the matrix without a significant loss of modulus. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45951.     

Improvement in toughness and crystallization of poly(L‐lactic acid) by melt blending with poly(epichlorohydrin‐co‐ethylene oxide)

Melt blending of poly(lactic acid) (PLA) and poly(epichlorohydrin‐co‐ethylene oxide) copolymers (ECO) was performed to improve the toughness and crystallization of PLA. Thermal and scanning electron microscopy analysis indicated that PLA and ECO were not thermodynamically miscible but compatible to some extent. The addition of a small amount of ECO accelerated the crystallization rate and increased the final crystallinity of PLA in the blends. Significant enhancement in toughness and flexibility of PLA were achieved by the incorporation of the ECO elastomer. When 20 wt% ECO added, the impact strength increased from 5 kJ/m² of neat PLA to 63.9 kJ/m², and the elongation at break increased from 5% to above 160%. The failure mode changed from brittle fracture of neat PLA to ductile fracture of the blend. Rheological measurement showed that the melt elasticity and viscosity of the blend increased with the concentration of ECO. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers.