丙烯醇催化氨化合成3-甲基吡啶催化剂的制备及性能

采用浸渍法制备了一系列H-ZSM-5分子筛负载过渡金属锌催化剂,在固定床反应器上考察了这些催化剂对丙烯醇催化氨化合成3-甲基吡啶的催化性能。通过对H-ZSM-5的硅铝比、锌负载量对催化剂催化性能影响的考察,发现硅铝比为80、锌负载量为12%时得到的催化剂Zn12/H-ZSM-5(80)的催化性能最佳。在常压、反应温度420℃、氨醇摩尔比3:1、空速300 h?1条件下,丙烯醇在该催化剂上的转化率和3-甲基吡啶的选择性分别达到97.8%和37.9%。利用X射线衍射(XRD)、X射线光电子能谱(XPS)以及吡啶吸附红外对催化剂进行了表征,结果表明,Zn12/H-ZSM-5(80)上负载的Zn2+为L酸;在丙烯醇生成3-甲基吡啶的反应过程中催化剂的脱氢活性物种为氧化锌,而加成和环合反应则主要是由催化剂中的L酸催化实现的。     

ZSM-5分子筛固定床催化合成聚甲氧基二甲醚

通过X射线衍射（XRD）、扫描电子显微镜（SEM）、氨气程序升温脱附（NH₃-TPD）和吡啶吸附-红外光谱（Py-IR）等对不同硅铝比（SiO₂/Al₂O₃）的ZSM-5分子筛粉末催化剂进行表征。在间歇反应器中,本文对比了不同硅铝比ZSM-5分子筛粉末催化三聚甲醛和甲缩醛合成聚甲氧基二甲醚（PODE）的催化活性,结果表明硅铝比为400的ZSM-5分子筛粉末具有最高的PODE_2~8的收率和选择性。然后,采用挤条成型法,在ZSM-5分子筛粉末（SiO₂/Al₂O₃=400）中加入硅溶胶黏结剂和甲基纤维素黏结剂,制备得到ZSM-5成型催化剂,硅溶胶添加量和甲基纤维素分子量影响成型催化剂强度。采用ZSM-5成型催化剂,以固定床为反应器,反应温度和反应空速在所考察的范围内对三聚甲醛（TOX）的转化率和PODE的选择性影响较小。在85℃、压力1MPa、空速为5h^-1的条件下进行了240h催化性能考察,成型催化剂催化性能稳定,三聚甲醛的转化率高于90%,PODE_2~8的选择性达到95%以上。     

Zn/NaHZSM-5沸石在C5～C8链烷烃芳构化反应中的催化性能

采用氨气程序升温脱附（NH₃-TPD）、紫外-可见光谱和小型固定床反应器，重点研究了碱金属钠离子和过渡金属锌离子改性对纳米H-ZSM-5沸石表面酸性及其催化C₅～C₈链烷烃芳构化反应性能的影响。结果表明，用碱金属钠离子改性能够有效地消除沸石表面的强酸中心，适当降低催化剂表面酸量，从而减少甲烷、乙烷和丙烷等低值副产物的生成，优化芳构化反应产物分布。适宜的Zn²⁺负载量为3%（质量分数），过高的Zn²⁺负载量会使产物中干气生成量增大，不利于芳烃收率的提高。C₅～C₈链烷烃芳构化的适宜反应温度为530℃。     

富氧条件Co/H-ZSM-5催化剂上CH4选择催化还原NO的研究

采用离子交换法制备了一系列具有不同硅铝比和不同Co负载量的Co/H-ZSM-5催化剂样品。富氧条件下考察了硅铝比、Co负载量、空速、O₂浓度及酸位对催化剂选择催化还原活性的影响。并对其进行了XRD、BET、H₂-TPR和DRS-UV-vis等表征。催化结果表明，催化剂的催化活性随Co负载量的增加而增加，随硅铝比的增加而减少；NO转化率随着空速的增加而降低。O₂体积分数为2%时，NO达最大转化率。表征结果表明，Co²⁺为活性中心，酸中心的存在对催化活性有一定的促进作用。     

NaAlCl4/γ-Al2O3@ZSM-5空心微球核壳复盐催化剂的制备及歧化性能研究

利用浸渍法将复盐NaAlCl₄负载在空心微球表面,对比不同硅铝摩尔比下催化剂的性能,研究了不同温度、不同NaAlCl₄负载质量分数（4%、8%、12%、16%）下催化剂的催化效率,利用XRD、BET、SEM、TEM、FT-IR、EDS等对催化剂进行表征。结果表明,在硅铝摩尔比为150、反应温度为200℃、复盐负载质量分数为8%、催化剂质量为0.7 g时,催化性能最好。     

杂多酸盐催化合成柠檬酸三丁酯研究

制备了1-（3-磺酸基）丙基-3-甲基咪唑磷钼酸盐（[MIMPS]₃PMo₁₂O₄₀）、1-（3-磺酸基）丙基-3-甲基咪唑磷钨酸盐（[MIMPS]₃PW₁₂O₄₀）和1-（3-磺酸基）丙基-3-甲基吡啶磷钨酸盐（[PyPS]₃PW₁₂O₄₀）3种杂多酸盐,用于催化柠檬酸和正丁醇合成柠檬酸三丁酯（TBC）,考察了各催化剂的催化效果。其中,[MIMPS]₃PMo₁₂O₄₀具有最好的催化效果,在其催化下,考察了反应条件对酯化率的影响。结果表明：当醇酸物质的量比为4.5:1.0、反应温度为130℃、反应时间为3.5h、催化剂用量为柠檬酸质量的5%时,酯化率可达98.3%,且催化剂具有较好的重复使用性能,重复使用5次后,酯化率依然保持在94%以上。     

用于丙烷催化燃烧的PdxPty-ZSM-5/Cordierite整体式催化剂

以ZSM-5分子筛、铝溶胶、硝酸钯、硝酸铂和水为原料制备分子筛浆料，采用真空抽提-一次涂覆法在堇青石蜂窝陶瓷载体表面制备出Pd_xPt_y-ZSM-5/Cordierite整体式催化剂，考察了Pd负载量、ZSM-5分子筛的硅铝比和Pd/Pt质量比对整体式催化剂的丙烷催化燃烧性能的影响，并用超声波振荡、SEM、XRD、H₂-TPR和C₃H₈-TPD等手段对整体式催化剂进行了表征。当球磨时间为60 min，分子筛浆料固含量为38%时，整体式催化剂的涂层上载量可达到178 g?L^-1，涂层脱落率低于0.5%。Pd₂Pt₃-ZSM-5/Cordierite整体式催化剂（贵金属总负载量为1.2 g?L^-1）对于丙烷的催化燃烧具有较好的催化活性（T₅₀=259℃，T₉₀=323℃）和稳定性，具有良好的工业应用前景，其中较低的ZSM-5分子筛硅铝比以及Pd和Pt之间的相互作用增加了对丙烷的吸附能力和表面活性氧物种的数量，从而提高了整体式催化剂的催化活性。     

Zn(OAc)2/AC催化固定床上CO2与1,2-丙二醇合成碳酸丙烯酯及其反应机理

以负载型乙酸锌为催化剂,在固定床上实现了CO₂和1,2-丙二醇(PG)合成碳酸丙烯酯(PC)反应。考察了不同载体和负载量对负载型乙酸锌催化性能的影响以及反应条件对PC合成反应的影响。结果表明:负载量为40% (质量分数)的Zn(OAc)₂/AC催化性能最好。CO₂与PG合成PC适宜的反应条件为:PG、乙腈和CO₂的摩尔比为1:1.8:11,CO₂ 压力 4.0 MPa,反应温度160 ℃和液空速0.9 h^-1。在此条件下,PC收率和选择性分别为6.3%和49.0%。采用原位红外结合设计实验研究了无水乙酸锌分别与CO₂和PG之间的相互作用,发现CO₂与乙酸锌之间的化学吸附比较弱,而PG与乙酸锌之间的化学吸附较强,能够活化PG。据此推测了乙酸锌催化CO₂与PG合成PC的反应机理。     

乙烷与苯经接力催化路线制备乙苯

设计乙烷经氯氧化制备乙烯再与苯烷基化一步法制备乙苯的接力催化路线。研制铈基氧化物作为活化乙烷生成中间产物乙烯的催化剂,并耦合H-ZSM-5沸石分子筛与苯进一步烷基化生成乙苯。在Mn/CeO₂氧化物与H-ZSM-5沸石分子筛以研磨混合形成的双功能催化剂上,实现了乙烷与苯催化制备乙苯的可控接力催化。考察了氧化物的组成、氧化物与沸石分子筛的耦合方式与最适质量配比、沸石分子筛的硅铝比对接力催化反应的影响,并进行了催化剂稳定性研究。结合X射线衍射（XRD）、NH₃程序升温脱附（NH₃-TPD）、透射电子显微镜（TEM）、X射线荧光光谱分析（XRF）等表征手段分析了催化剂结构及其与催化性能的构效关系。提出后续催化剂研究的关键在于分子筛烷基化能力以及抗流失能力的提高。     

Fe2O3/AC催化剂上对甲基苯硫酚的水相催化氧化偶联

以对甲基苯硫酚为模型底物，空气为氧化剂，来研究硫醇水相催化氧化偶联制备二硫醚。以活性炭为载体，采用等体积浸渍法制备了一系列负载型氧化物催化剂，并考察了其在对甲基苯硫酚氧化偶联制备对甲苯二硫醚反应中的催化性能。反应结果表明，活性炭负载的铁氧化物具有最佳催化性能。采用N₂物理吸附、X射线衍射、X射线光电子能谱和透射电镜等表征手段对活性炭负载的铁氧化物催化剂进行了表征。表征结果表明，铁氧化物为高度分散在活性炭上的Fe₂O₃物种。以Fe₂O₃/AC为催化剂，当催化剂焙烧温度为400℃，Fe负载量为5%，在50℃下反应30min时，对甲苯二硫醚的收率高达97.4%；该催化剂循环使用5次后活性无明显下降。     

Pt/ZSM-35催化长链正构生物烷烃加氢裂化/异构化制航空煤油

以生物质油加氢脱氧得到的长链正构生物烷烃为原料，考察了H-MCM-49、H-ZSM-5、H-ZSM-22和 H-ZSM-35这4种不同分子筛催化剂的物化性质及其加氢裂化/异构化制生物航空煤油的性能。在此基础上，以H-ZSM-35分子筛为载体，制备并表征了一系列低负载量（0.1%、0.2%和0.3%）的Pt/ZSM-35双功能催化剂，以长链正构生物烷烃转化率、C₉~C₁₆产物选择性、生物航空煤油收率和异正比为指标，对其加氢裂化/异构化制生物航空煤油反应性能进行了评价，并对反应工艺条件进行优化。结果表明：H-ZSM-35的强酸中心强度高、酸量大，其结构中较小的孔口和较大的球型笼使其具有一定的容烃量和较好的择形性能，0.1%~0.3% Pt负载后， Pt/ZSM-35双功能催化剂表现出很好的加氢裂化/异构化活性和选择性。采用0.1% Pt/ZSM-35双功能催化剂在反应条件为320℃、1MPa、0.7h^-1、氢油比840∶1时，长链正构生物烷烃的转化率为84.3%，生物航空煤油收率达41.1%，产物异正比为1.34。81h长运转测试结果表明，该催化剂具有很好的稳定性。     

Multi-metal cyanide catalysts for ring-opening polymerization of propylene oxide

Polymerizations of propylene oxide (PO) have been carried out by using a series of multi-metal metal cyanide (MMC) catalysts prepared by reacting ZnCl₂ and K₃[Co(CN)₆]₂, K₄Fe(CN)₆, K₃Fe(CN)₆ and/or K₂Ni(CN)₄ in the presence of tert-butyl alcohol and polytetramethylene ether glycol as complexing agents. The resulting MMC catalysts are characterized by elemental analysis, X-ray photoelectron spectroscopy, infrared spectroscopy and X-ray powder diffraction. The structure of MMC catalysts with broadened X-ray diffraction peaks is different from that of highly crystalline Prussian blue analogues of microporous crystalline materials due to the coordination of complexing agents. The PO polymerization behavior was tunable by changing with various metal cyanide salts after fixing a main catalyst component as ZnCl₂. Even if the basic structure of the MMC complexes is different each other, i.e. orthorhombic for Zn₂[Fe(CN)₆] and monoclinic for Zn₃[Fe(CN)₆]₂ and Zn₃[Co(CN)₆]₂, the chemical formulations become more complicated by forming MMC complexes through cyano bridges and complexing agents’ coordination and the structure more distorted from the defined crystal structures. All catalysts prepared by using K₃[Co(CN)₆]₂ showed very high activity once they were activated. Simply changing catalyst formulation by choosing different metal cyanide salts, catalytic activity, induction period, polymer molecular weight and its distribution and polymer viscosity could be tuned.     

Controllable synthesis of novel nanoporous manganese oxide catalysts for the direct synthesis of imines from alcohols and amines

A novel template-free oxalate route was applied to synthesize different mesoporous manganese oxides (amorphous manganese oxide (AMO), Mn₅O₈, Mn₃O₄, MnO₂) in the narrow temperature range from 350℃ to 400℃ by controlling the calcination conditions, which were employed as the efficient catalysts for the oxidative coupling of alcohols with amines to imines. The chemical and structural properties of the manganese oxides were characterized by the methods of thermogravimetry analysis and heat flow (TG-DSC), X-ray diffraction (XRD), nitrogen sorption, scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), H₂ temperature-programmed reduction (H₂-TPR), and inductively coupled plasma optical emission spectrometry (ICP-OES) techniques. The structures of different manganese oxides were confirmed by characterization. The M-350 (AMO) presented the maximum surface area, amorphous nature, the lowest reduction temperature, the higher (Mn³⁺ + Mn⁴⁺)/Mn²⁺ ratio, and the higher adsorbed oxygen species compared to other samples. Among the catalysts, M-350 showed the best catalytic performance using air as an oxidant, and the conversion of benzyl alcohol (BA) and the selectivity of N-benzylideneaniline (NBA) reached as high as 100% and 97.1% respectively at the lower reaction temperature (80℃) for 1 h. M-350 had also the highest TOF value (0.0100 mmol·mg^-1·h^-1) compared to the other manganese oxide catalysts. The catalyst was reusable and gave 95.8% conversion after 5 reuse tests, the XRD pattern of the reactivated M-350 did not show any obvious change. Lattice oxygen mobility and (Mn³⁺ + Mn⁴⁺)/Mn²⁺ ratio were found to play the important roles in the catalytic activity of aerobic reactions.     

AgBr/Zn3(OH)2V2O7·2H2O可见光催化降解亚甲基蓝溶液

采用水热和沉淀两步合成法制备AgBr/Zn₃(OH)₂V₂O₇·2H₂O催化剂,研究其在可见光下降解亚甲基蓝溶液的性能,并考察催化剂用量、亚甲基蓝溶液初始浓度、pH值以及盐浓度对光催化性能的影响,评价AgBr/Zn₃(OH)₂V₂O₇·2H₂O催化剂的重复使用性能。结果表明,在前驱液pH为10、120 ℃水热10 h、Ag与Br物质的量比为0.20条件下制备的复合催化剂在可见光下反应120 min后,1.0 g·L^-1的催化剂对10 mg·L^-1的亚甲基蓝溶液脱色率达到85.2%。NaCl对亚甲基蓝的降解起抑制作用,Na₂SO₄对亚甲基蓝的降解起促进作用。催化剂重复使用4次后,光照120 min后的亚甲基蓝溶液脱色率可达66.4%。催化剂对不同初始浓度亚甲基蓝溶液的光催化降解符合一级动力学模型。     

Selective hydrogenation of cinnamaldehyde over Raney cobalt catalysts modified with salts of heteropolyacids

The hydrogenation of cinnamaldehyde to cinnamyl alcohol was carried out over Raney cobalt catalysts modified by Cu_3/2PMo₁₂O₄₀. It was found that the conversion of cinnamaldehyde decreases substantially with increases in the amount of Cu_3/2PMo₁₂O₄₀ deposited on Raney cobalt catalysts. The maximum yield of cinnamyl alcohol varies with the amount of deposited Cu_3/2PMo₁₂O₄₀. The more the deposited modifier, the higher the attainable maximum yield of cinnamyl alcohol. With 2.8% Cu_3/2PMo₁₂O₄₀ modified Raney cobalt, the selectivity for cinnamyl alcohol does not change with reaction temperature and reaction time. Thus, it is likely that the selectivity of ca. 80% for cinnamyl alcohol represents a specific value which is related to the nature of the surface modifier, Cu_3/2PMo₁₂O₄₀. The influences of the heteropolyanions and the competitive cations on the conversion and the selectivity were also investigated. It was found that copper salts of different heteropolyacids acting as the modifier of the catalyst bring about different enhancements in the selectivity for cinnamyl alcohol. The order of enhancement of selectivity in terms of heteropolyacid anion is PMo₁₂O³⁻₄₀>SiMo₁₂O⁴⁻₄₀>PW₁₂O³⁻₄₀. There is little difference in selectivity by modification with (NH₄)₆Mo₇O₂₄ and Cu₂SiMo₁₂O₄₀. Raney cobalt catalyst modified by different 12-molybdophosphate containing cations of alkali, alkaline earth and transition metals gives a similar selectivity of about 75%. Among all of the 12-molybdophosphates, that containing the cation Cu²⁺ is the best in improving the selectivity of the catalysts. A selectivity as high as 83% was attained when an amount of 2.8% Cu_3/2PMo₁₂O₄₀ was deposited on the catalyst.     

固体酸表面B酸和L酸与果糖转化制乳酸甲酯产物分布

制备了γ-Al₂O₃、HZSM-5、SnOPO₄、SnZrOPO₄(1:1)、SO₄^2-/ZrO₂5种不同的固体酸催化剂,采用NH₃程序升温脱附、吡啶原位吸附红外对催化剂进行了表征。考察了固体酸催化果糖在甲醇中转化的催化性能,结果表明,果糖的转化率均高于98%,产物分布与固体酸表面L酸、B酸酸量具有显著的相关性,乳酸甲酯的收率随着L酸量的减少而降低,L酸催化剂γ-Al₂O₃催化,主产物只有乳酸甲酯,收率为24.4%。而L酸位和B酸位共存的固体酸,产物中有乳酸甲酯、乙酰丙酸甲酯,并且乙酰丙酸甲酯的收率随着B酸量的增多而升高。最后考察了典型L酸γ-Al₂O₃及B酸L酸共存的固体酸HZSM-5不同反应时间的产物分布,结合气相-质谱联用对产物定性分析,得出了果糖转化过程L酸位催化和B酸位催化的反应路径。     

SBA-15固载磷钨酸催化剂的制备及催化合成叔丁基苯酚

以不同硅烷偶联剂改性的介孔分子筛SBA-15为载体、PW_(12)为催化剂,通过对SBA-15表面共价及非共价修饰制备磷钨酸@介孔分子筛/硅烷偶联剂复合催化剂PW_(12)@SBA-15/YSiX_3(YSiX_3=Apts、Atapts、Papts);并利用FT-IR、XRD、TEM、N_2吸附-脱附对其组成、结构及形貌进行表征。以改性SBA-15分子筛固载磷钨酸催化剂催化合成叔丁基苯酚为研究对象,考察不同硅烷偶联剂、反应温度、苯酚与叔丁醇物质的量比对催化合成叔丁基苯酚的影响,并获得合成叔丁基苯酚的最佳工艺条件,即反应温度145℃、n(苯酚)∶n(叔丁醇)=1∶2.5、重时空速2.2 h~(-1),该最佳反应条件下,PW_(12)@SBA-15/Apts催化剂催化合成叔丁基苯酚的催化活性最高,苯酚转化率为98.3%,2,4-二叔丁基苯酚选择性为57.3%.     

Enhanced activity of an In–Fe2O3/H-ZSM-5 catalyst for NO reduction with methane

Selective reduction of NO by CH₄ on an In–Fe₂O₃/H-ZSM-5 catalyst was investigated in the presence of excess oxygen. Compared with In/H-ZSM-5, the In–Fe₂O₃/H-ZSM-5 catalyst with high Fe₂O₃ contents showed higher activity in a wide range of reaction temperatures. It was found that the addition of Fe₂O₃ yielded a promotion effect on CH₄ activation. The influence of water vapor on NO conversion was also investigated. The activity of the In/H-ZSM-5 catalyst has been found to be strongly inhibited by water vapor, while the In–Fe₂O₃/H-ZSM-5 catalyst remained fairly active in the presence of 3.3% steam.     

Al掺杂的Cu/SBA-15催化剂用于己二酸二甲酯加氢合成1,6-己二醇

作为一种重要的有机合成原料,1,6-己二醇(HDO)的工业化生产主要通过己二酸二甲酯(DMA)加氢反应来实现,而理性设计开发相应的Cu基催化剂是提高HDO产率的关键。本文采用Al掺杂的介孔分子筛SBA-15为载体制备得到了一系列CuAlx/SBA-15催化剂,探究了使用该催化剂用于DMA加氢反应合成HDO的催化性能和催化机理,并对反应条件进行了优化。研究结果表明：CuAl₅/SBA-15催化剂能够增加催化剂的路易斯酸酸量,提高Cu⁺/Cu⁰的比例,从而提升DMA加氢反应的选择性,同时Al的掺杂也能减少Cu活性组分的团聚,从而增强催化剂的稳定性。当反应温度为240℃、反应压力为6MPa、反应时间为6h时,HDO的反应产率达到最大,为87.05%;重复使用CuAl₅/SBA-15催化剂36h后,HDO的反应产率能够维持在86.01%左右。本文的研究结果对设计Cu基催化剂用于酯加氢反应具有一定的借鉴意义。     

Study of M-ZSM-5 nanocatalysts (M:Cu,Mn, Fe,Co...) for selective catalytic reduction of NO with NH3: Process optimization by Taguchi method

A series of different transition metals (V, Co, Cr, Mn, Fe, Ni, Cu and Zn) promoted H-ZSM-5 catalysts were prepared by impregnation method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The catalytic activity of these catalysts was evaluated for the selective catalytic reduction (SCR) of NO with NH₃ as reductant in the presence of oxygen. The results revealed that the catalytic activity of Cu-ZSM-5 nanocatalyst for NO conversion to N₂ was 80% at 300 ℃, which was the best among various promoted metals. Design of experiments (DOEs) with Taguchi method was employed to optimize NH₃-SCR process parameters such as NH₃/NO ratio, O₂ concentration, and gas hourly space velocity (GHSV) over Cu-ZSM-5 nanocatalyst at 250 and 300 ℃. Results showed that the most important parameter in NH₃-SCR of NO is O₂ concentration; followed by NH₃/NO ratio and GHSV has little importance. The NO conversion to N₂ of 63.1% and 94.86%was observed at 250 ℃ and 300 ℃, respectively under the obtained optimum conditions.