Effects of temperature and strain rate on the tensile behavior of unfilled and talc‐filled polypropylene. Part I: Experiments

The tensile behavior of unfilled and 40 w% talc‐filled polypropylene has been determined at four different temperatures (21.5, 50, 75 and 100°C) and three different strain rates (0.05, 0.5 and 5 min^?1). Experimental results showed that both unfilled and talc‐filled polypropylenes were sensitive to strain rate and temperature. Stressstrain curves of both materials were nonlinear even at relatively low strains. The addition of talc to polypropylene increased the elastic modulus, but the yield strength and yield strain were reduced. The temperature and strain rate sensitivities of these materials were also different. An energy‐activated, rate sensitive Eyring equation was used to predict the yield strength of both materials. It is shown that both activation volume and activation of energy increased with the addition of talc in polypropylene.     

“Pore/bead” membrane for rechargeable lithium ion batteries

A special “pore/bead” membrane was prepared with a mesoporous inorganic filler (MCM‐41) and a P(VDF‐HFP) binder. The special “pore/bead” structure of the MCM‐41 filler not only enhanced the puncture strength of the membrane but also improved its ionic conductivity. The puncture strength of the dried “pore/bead” membrane (MCM‐41 : P(VDF‐HFP) = 1 : 1.5) was 18 N, and showed a slight decrease (16 N) after the membrane was wetted by liquid electrolyte. Additionally, the composite membrane showed excellent thermal dimensional stability. The composite membrane could be activated by adding 1M LiClO₄‐EC/DMC (1 : 1 by volume). The activated membrane displayed a high ionic conductivity about 3.4 × 10^?3 S cm^?1 at room temperature. Its electrochemical stability window was up to 5.3 V vs. Li/Li⁺, indicating that it was very suitable for lithium‐ion battery application. The battery assembled using the composite electrolyte also showed reasonably good high‐rate performance. The approach of preparing a “pore/bead” membrane provides a new avenue for improving both the conductivity and the mechanical strength of polymer electrolytes for lithium batteries. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical properties and deformation behaviors of acrylonitrile‐butadiene‐styrene under Izod impact test and uniaxial tension at various strain rates

Two polybutadiene‐graft‐acrylonitrile‐styrene copolymer (PBD‐g‐SAN) impact modifiers with different rubber particle size were synthesized by seeded emulsion polymerization. Acrylonitrile‐butadiene‐styrene (ABS) blends with a constant rubber concentration of 15 wt% were prepared by blending those impact modifiers and SAN resin. The major focus was the mechanical properties and deformation mechanisms of ABS blends under Izod impact test and uniaxial tension at various strain rates from 2.564 × 10^?4 S^?1 upto 1.282 × 10^?1 S^?1. By the combination of transmission electron microscope and scanning electron microscope, it was concluded that crazes and cavitation coexisted in ABS blends. The deformation mechanisms of ABS blend containing large rubber particles was rubber particles cavitation and shear yielding in the matrix including crazes, and they do not change with the strain rate. Different from ABS blend with large rubber particles, deformation mechanism of ABS with small rubber particles under tensile condition was only involved in shear yielding in the matrix and no crazes were formed. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Crosslinked hydroxyl‐conductive copolymer/silica composite membranes based on addition‐type polynorbornene for alkaline anion exchange membrane fuel cell applications

Crosslinked hydroxyl‐conductive copolymer/silica composite membranes based on addition‐type polynorbornene, poly(dodoxymethylene norbornene‐co‐norbornene‐3‐(trimethylpropyl ammonium)‐functionalized silica (QP(DNB/NB‐SiO₂), were prepared by a sol–gel method. Copolymer composite membranes with different degree of quaternary ammonium functional silica, designated as QP(DNB/NB‐SiO₂‐X) (X = 5, 10, 15 and 25 wt%, respectively), displayed good dimensional stabilities with low in‐plane swelling rate of 1.32–3.7%, good mechanical properties with high elastic modulus of 605.4–756.8 MPa and high tensile strength of 13.2–20 Mpa. The achieved copolymer composite membranes could self‐assemble into a microphase‐separated morphology with randomly oriented long‐range aliphatic chain/cylinder ionic channels that were imbedded in the hydrophobic PNB matrix. Among these membranes, the QP(DNB/NB‐SiO₂‐25) showed the parameter with ionic conductivity of 9.33 × 10^?3S cm^?1, methanol permeability of 2.89 × 10^?7cm² s^?1, and ion‐exchange capacity(IEC) of 1.19 × 10^?3 mol g^?1. A current density of 82.3mA cm^?2, the open circuit voltage of 0.65 V and a peek power density of 32 mW cm^?2 were obtained. POLYM. ENG. SCI., 58:13–21, 2018. © 2017 Society of Plastics Engineers     

A biaxial stretched β‐isotactic polypropylene microporous membrane for lithium‐ion batteries

In this article, microporous polypropylene (PP) membranes were produced with TMB‐5 as β‐crystal nucleating agent by biaxial stretching. Influences of different concentration of TMB‐5 were studied using differential scanning calorimetry and X‐ray diffraction. It was found that the highest crystallinity was reached when the nucleating agent content was 0.5 wt %. The effect of stretching temperature and stretching ratio on pore size distribution and porosity of the membranes were investigated by scanning electron microscopy and mercury porosimeter, respectively. And physical properties, such as tensile strength, permeability, and puncture resistance of the microporous membrane prepared at the optimized conditions, were evaluated. Compared with commercial PP separator membrane, the as‐prepared microporous membrane shows similar uniform pore size distribution and exhibits slightly higher porosity and ionic conductivities. When used as lithium‐ion separator, the experimental film shows more stable cycling performance than the commercial one. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45825.     

Polyethylene battery separator with auto‐shutdown ability,thermal stability of 220°C,and hydrophilic surface via solid‐state ultraviolet irradiation

To assure the safety of the lithium‐ion battery, the separator is required to have good thermal stability. Because the single‐layer polyethylene (PE) separator can only tolerate a temperature of 130°C, it is seldom employed currently by lithium‐ion battery manufacturers although its cost is low. In this article, we modified PE separator chain structure through solid‐state ultraviolet (UV) irradiation method to achieve a separator with composite structure of ～40% crystallized PE and ～70% gel content. Approximately 40% crystallized PE chains fulfill the task of auto‐shutdown at 130°C through melting and filling the pores. At the same time, the PE separator can maintain integrity till 220°C because of its highly cross‐linked chain structure. Besides, the modified PE separator is hydrophilic with a water contact angle of 33° after UV treatment and is able to absorb more electrolyte. However, the tensile strength and elongation at the break decreased because the cross‐linking network increased the rigidity. Nevertheless, these values still meet the requirements as the separator for lithium‐ion battery. Considering the low cost and easy preparation, current cross‐linked PE separator has potential to be used in lithium‐ion batteries for various applications, including electric vehicles and energy storage purpose. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42169.     

Damage to rigid‐particle‐filled polymer under cyclic tension

The effect of particle volume fraction, strain rate and interfacial bonding strength on the damage to a glass bead‐filled high density polyethylene composite was studied experimentally by means of cyclic tension tests. Although the volume fraction of the glass beads varies from 5% to 25%, the materials studied are always sensitive to the strain rate, reflected by an increase of the modulus with strain rates changing from 10^?3 s^?1 to 10^?5 s^?1. The damage evolution is a function of the applied far‐field strain, but is also strongly influenced by the particle volume fraction, strain rate and interfacial bonding strength. Strong interfacial adhesion can postpone the initiation of damage and cause a lower level of damage than that occuring with weak adhesion under a given strain. For the studied materials with interfacial debonding taking place, the higher the volume fraction of the glass beads, the greater the number of microcracks formed at the interface. The effect of strain rate on the damage may be related to the effect of loading time, ie low strain rate favours damage development. The residual strain is a function of far‐field strain and also depends on the strain rate and residual deformation of microvoids formed at two poles of the particle. © 2001 Society of Chemical Industry     

Fabrication of a Glass‐Ceramic‐to‐Metal Seal Between Ti–6Al–4V and a Strontium Boroaluminate Glass

Glass‐ceramics are widely utilized in the electronics industry to provide electrical insulation and to form leak‐tight joints with a range of metals. The coefficient of thermal expansion (CTE) of the glass‐ceramic can be controlled by the extent of crystallization to reduce detrimental tensile stresses in the joint. In recent years, there has been interest in using titanium alloys, in place of stainless steels, due to their lower density and superior specific strength. In this study, the heat treatment of a strontium boroaluminate glass has been tailored to create glass‐ceramics with mean CTEs ranging from 5.7 ± 0.1 × 10^?6/K to 9.7 ± 0.1 × 10^?6/K over the temperature range 303–693 K. The resultant glass‐ceramic consists of three crystalline phases and residual glass. A glass‐ceramic with a mean CTE of 6.9 ± 0.1 × 10^?6/K was subsequently fabricated to form a compression seal with a Ti–6Al–4V housing and a preoxidized Kovar pin. Single pin assemblies were shown to be reproducible in terms of microstructure and all passed a standard helium leak test, indicating that a successful seal had been produced.     

Preparation of phosphorylated nata‐de‐coco for polymer electrolyte membrane applications

Fuel cells are being developed to overcome the global energy crisis. The objective of this research is to prepare an environmental‐friendly and cheap material as the polymer electrolyte membrane. Coconut water was fermented by Acetobacter xylinum to produce nata‐de‐coco and the phosphorylation was carried out by microwave‐assisted reaction. The resulting membranes are characterized by ion exchange capacity, contact angle, proton conductivity, swelling index, methanol permeability, mechanical properties measurement and morphological analysis. At the optimum phosphorylation condition using 17.35 mmol of phosphoric acid, membrane showed a proton conductivity of 1.2 × 10^?2 S/cm and a methanol permeability of 2.3 × 10^?6 cm²/s. The tensile strength of the produced membranes increases significantly and the arrangement of the cellulosic fibers are kept well‐aligned. It is concluded that a green and sustainable natural resources can be used for preparing electrolyte membrane. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and properties of the single‐walled carbon nanotube/cellulose nanocomposites using N‐methylmorpholine‐N‐oxide monohydrate

Single‐walled carbon nanotube (SWNT)/cellulose nanocomposite films were prepared using N‐methylmorpholine‐N‐oxide (NMMO) monohydrate as a dispersing agent for the acid‐treated SWNTs (A‐SWNTs) as well as a cellulose solvent. The A‐SWNTs were dispersed in both NMMO monohydrate and the nanocomposite film (as confirmed by scanning electron microscopy) because of the strong hydrogen bonds of the A‐SWNTs with NMMO and cellulose. The mechanical properties, thermal properties, and electric conductivity of the nanocomposite films were improved by adding a small amount of the A‐SWNTs to the cellulose. For example, by adding 1 wt % of the A‐SWNTs to the cellulose, tensile strain at break point, Young's modulus, and toughness increased ～ 5.4, ～ 2.2, and ～ 6 times, respectively, the degradation temperature increased to 9°C as compared with those of the pure cellulose film, and the electric conductivities at ? (the wt % of A‐SWNTs in the composite) = 1 and 9 were 4.97 × 10^?4 and 3.74 × 10^?2 S/cm, respectively. Thus, the A‐SWNT/cellulose nanocomposites are a promising material and can be used for many applications, such as toughened Lyocell fibers, transparent electrodes, and soforth. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Tensile behavior of polypropylene blended with bimodal distribution of styrene‐ethylene‐butadiene‐styrene particle size

The objective is to characterize the effects of the bimodal distribution of rubber particles and its blend ratio on the mechanical properties of the thermoplastic polypropylene blended with two different styrene‐ethylene‐butadiene‐styrene triblock copolymer at the intermediate and high strain rates. Tensile tests are conducted at the nominal strain rates from 3 × 10^?1 to 10² (1/s). Phase morphology is investigated to estimate the bimodal rubber particle size distribution. In addition, the in situ observation is conducted during uniaxially stretching within transmission electron microscopy step by step to investigate the deformation events depending on the elongation of samples. The elastic modulus increased gradually as the blend ratio of large rubber particle increased. An increase in the rupture strain and the strain energy up to failure was found for the bimodal rubber particle distributed blend system where the blend ratios of small rubber particle and large rubber particle were same. This is because the smaller particles dominant blend systems show the bandlike craze deformation while the localized plastic deformation is taken place in the larger particles dominated blend systems. The synergistic effect of these rubber particles gives rise to a strong increase in the ductility of these bimodal rubber particle distributed polypropylene systems. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polydopamine hydrophilic modification of polypropylene separator for lithium ion battery

The modified polypropylene (PP) separators with self‐polymerization of dopamine on the surfaces are prepared by a simple solution‐immersion method to improve the interfacial hydrophilic and discharge performance. The contact angle test and the liquid electrolyte uptake capacity test results show that the wettability and the electrolyte‐retention ability of polydopamine‐modified separator are improved significantly. The robust and thin polydopamine layer on the surface also enhances thermal performance and tensile strength of the modified PP separator certified by DSC and tensile strength tests. The ionic conductivity of the modified PP separator is up to 3.08 mS·cm^?1, ～2.5 times of the bare separator. Good discharge capacity retention and C‐rate discharge performance are demonstrated by a 2025 coin half‐cell with the liquid electrolyte‐soaked polydopamine modified PP separator sandwiched between lithium metal anode and LiFePO₄ cathode. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40543.     

Composite polymer electrolytes based on electrospun thermoplastic polyurethane membrane and polyethylene oxide for all‐solid‐state lithium batteries

To improve the electrochemical properties and enhance the mechanical strength of solid polymer electrolytes, series of composite polymer electrolytes (CPEs) were fabricated with hybrids of thermoplastic polyurethane (TPU) electrospun membrane, polyethylene oxide (PEO), SiO₂ nanoparticles and lithium bis(trifluoromethane)sulfonamide (LiTFSI). The structure and properties of the CPEs were confirmed by SEM, XRD, DSC, TGA, electrochemical impedance spectroscopy and linear sweep voltammetry. The TPU electrospun membrane as the skeleton can improve the mechanical properties of the CPEs. In addition, SiO₂ particles can suppress the crystallization of PEO. The results show that the TPU‐electrospun‐membrane‐supported PEO electrolyte with 5 wt% SiO₂ and 20 wt% LiTFSI (TPU/PEO‐5%SiO₂‐20%Li) presents an ionic conductivity of 6.1 × 10^?4 S cm^?1 at 60 °C with a high tensile strength of 25.6 MPa. The battery using TPU/PEO‐5%SiO₂‐20%Li as solid electrolyte and LiFePO₄ as cathode shows an attractive discharge capacity of 152, 150, 121, 75, 55 and 26 mA h g^?1 at C‐rates of 0.2C, 0.5C, 1C, 2C, 3C and 5C, respectively. The discharge capacity of the cell remains 110 mA h g^?1 after 100 cycles at 1C at 60 °C (with a capacity retention of 91%). All the results indicate that this CPE can be applied to all‐solid‐state rechargeable lithium batteries. © 2018 Society of Chemical Industry     

Ionic conductivity and morphology of semi‐interpenetrating‐type polymer electrolyte entrapping poly(siloxane‐g‐allyl cyanide)

We prepared a semi‐IPN (interpenetrating network)‐type solid polymer electrolyte (SPE) using poly (ethylene glycol)dimethacrylate (PEGDMA) as a polymer matrix containing a monocomb‐type poly(siloxane‐g‐allyl cyanide) and poly(ethylene glycol)dimethylether (PEGDME) for the lithium secondary battery. The poly(siloxane‐g‐allyl cyanide)s were prepared by a hydrosilation reaction of poly (methyl hydrosiloxane) with allyl cyanide and characterized by ¹H NMR and FTIR. The semi‐IPN‐type electrolyte was prepared by thermal curing, and conductivities of samples were measured by impedance spectroscopy using an indium tin oxide (ITO) electrode. The ionic conductivity of the semi‐IPN‐polymer electrolyte was about 1.05 × 10^?5 S cm^?1 with 60 wt % of the poly(siloxane‐g‐allyl cyanide) and 6.96 × 10^?4 S cm^?1 with 50 wt % of the PEGDME and 10 wt % of the poly(siloxane‐g‐allyl cyanide) at 30°C. The SEM morphology of the cross section of the semi‐IPN‐polymer electrolyte film was changed from discontinuous network to continuous network as increasing the PEGDME content and decreasing the poly(siloxane‐g‐allyl cyanide) content. The mechanical stability was also enhanced when increasing the PEGDME content. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Interfacial modification of single‐walled carbon nanotubes for high‐loading‐reinforced polypropylene composites

In this article, we present a strategy for fabricating polypropylene (PP)/polypropylene‐regrafted single‐walled carbon nanotube (PP‐re‐g‐SWNT) composites with a high loading of single‐walled carbon nanotubes (SWNTs; 20 wt %). The PP‐re‐g‐SWNTs were characterized by X‐ray photoelectron, Fourier transform infrared spectroscopy, transmission electron microscopy, and thermogravimetric analysis (TGA). The PP‐re‐g‐SWNTs showed excellent interfacial adhesion and dispersion. Furthermore, PP molecules, about 72 wt % by mass, were homogeneously bonded onto the surface of the SWNTs according to TGA. In this hybrid nanocomposite system, the PP‐re‐g‐SWNTs were covalently integrated into the PP matrix and became part of the conjugated network structure (as evidenced by differential scanning calorimetry and dynamic mechanical analysis) rather than just a separate component. Accordingly, the PP/PP‐re‐g‐SWNT composites presented obvious improvements in mechanical properties and conductivity (from 10^?10 to 10^?2). Most importantly, the tensile and flexural strength of the PP/PP‐re‐g‐SWNT composites did not exhibit an obvious downturn with the addition of 20 wt % SWNTs; this was contrary to documented results. We believe that these new observations were due to the novel structure of the PP‐re‐g‐SWNTs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39817.     

Melt‐processed biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): Effects of processing conditions on biodegradation

Biodegradable polyester blends were prepared from poly(L ‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) (50/50) by melt‐blending, and the effects of processing conditions (shear rate, time, and strain) of melt‐blending on proteinase‐K‐ and lipase‐catalyzed enzymatic degradability were investigated using gravimetry, differential scanning calorimetry, and scanning electron microscopy. The proteinase‐K‐catalyzed degradation rate of the blend films increased and leveled off with increasing the shear rate, time, or strain for melt‐blending, except for the shortest shear time of 60 s. The optimal processing conditions of melt‐blending giving the maximum rate of lipase‐catalyzed degradation were 9.6 × 10² s^?1 and 180 s, whereas a deviation from these conditions caused a reduction in lipase‐catalyzed enzymatic degradation rate. At the highest shear rate of 2.2 × 10³ s^?1, PCL‐rich phase was continuous in the blend films, irrespective of the shear time (or shear strain), whereas PLLA‐rich phase changed from dispersed to continuous by increasing the shear time (or shear strain). This study revealed that the biodegradability of PLLA/PCL blend materials can be manipulated by altering the processing conditions of melt‐blending (shear rate, time, or strain) or the sizes and morphology of PLLA‐rich and PCL‐rich domains. The method reported in the present study can be utilized for controlling the biodegradability of other biodegradable polyester blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 831–841, 2007     

Static and dynamic compressive properties of polypropylene/zinc oxide nanocomposites

The effect of strain rate is widely recognized as an essential factor that influences the mechanical properties of polymer matrix composites. Despite its importance, no previous work has been reported on the high‐strain rate behavior of polypropylene/zinc oxide nanocomposites. Based on this, static and dynamic compression properties of polypropylene/zinc oxide nanocomposites, with particle contents of 1%, 3%, and 5% by weight, were successfully studied at different strain rates (i.e., 0.01 s^?1, 0.1 s^?1, 650 s^?1, 900 s^?1, and 1100 s^?1) using a universal testing machine and a split Hopkinson pressure bar apparatus. For standardization, approximately 24 nm of zinc oxide nanoparticles were embedded into polypropylene matrix for each of the tested polypropylene/zinc oxide nanocomposites. Results show that the yield strength, the ultimate strength, and the stiffness properties, of polypropylene/zinc oxide nanocomposites, were greatly affected by both particle loading and applied strain rate. Furthermore, the rate sensitivity and the absorbed energy of all tested specimens showed a positive increment with increasing strain rate, whereas the thermal activation volume showed a contrary trend. In addition, the fractographic analysis and particle dispersion of all composite specimens were successfully obtained using a field emisission scanning electron microscopy. POLYM. ENG. SCI., 54:949–960, 2014. © 2013 Society of Plastics Engineers     

Synthesis and properties of fluorinated biphenyl‐type epoxy resin

A novel fluorinated biphenyl‐type epoxy resin (FBE) was synthesized by epoxidation of a fluorinated biphenyl‐type phenolic resin, which was prepared by the condensation of 3‐trifluoromethylphenol and 4,4′‐bismethoxymethylbiphenyl catalyzed in the presence of strong Lewis acid. Resin blends mixed by FBE with phenolic resin as curing agent showed low melt viscosity (1.3–2.5 Pa s) at 120–122°C. Experimental results indicated that the cured fluorinated epoxy resins possess good thermal stability with 5% weight loss under 409–415°C, high glass‐transition temperature of 139–151°C (determined by dynamic mechanical analysis), and outstanding mechanical properties with flexural strength of 117–121 MPa as well as tensile strength of 71–72 MPa. The thermally cured fluorinated biphenyl‐type epoxy resin also showed good electrical insulation properties with volume resistivity of 0.5–0.8 × 10¹⁷ Ω cm and surface resistivity of 0.8–4.6 × 10¹⁶ Ω. The measured dielectric constants at 1 MHz were in the range of 3.8–4.1 and the measured dielectric dissipation factors (tan δ) were in the range of 3.6–3.8 × 10^?3. It was found that the fluorinated epoxy resins have improved dielectric properties, lower moisture adsorption, as well as better flame‐retardant properties compared with the corresponding commercial biphenyl‐type epoxy resins. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Evolution of mechanical properties of polypropylene separator in liquid electrolytes for lithium‐ion batteries

Knowledge of the mechanical behaviors of polymeric separators immersed in liquid electrolytes is of great significance for predicting the long‐term performance of lithium batteries with high performance and safety. In terms of tensile tests, heating shrinkage, and dynamic mechanical analysis as well as the essential work of fracture method, the study reported here encompasses a systematic investigation of the mechanical properties of a typical commercial polypropylene separator in mixtures of ethylene carbonate and dimethyl carbonate and lithium hexafluorophosphate (LiPF₆), comparing with the results in ionic liquid (IL) electrolyte composed of lithium tetrafluoroborate (LiBF₄) and 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMIBF₄) and dry condition. It has been found that liquid electrolytes have obvious negative effect on the dimensional stability at elevated temperature and mechanical properties, especially on crack resistance of the polymer separator. LiBF₄‐BMIBF₄ has much smaller damage on the strength, Young's modulus and fracture toughness of separator than the organic solution except the dynamic modulus at high temperature. Notably, the maximum tensile stress, Young's modulus and the reciprocal of relaxation time of the polymer separator are linearly dependent with strain rate under quasi‐static condition, and the relaxation time has clarified the coupling effect mechanism of liquid electrolyte and loading rate. Moreover, the non‐dimensional viscoelastic constitute equation could perfectly track the tensile behavior of wet and dry separators at different strain rate, and a property model could well characterize the temperature‐dependent storage modulus of polymer separators from rubbery to viscous state. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46441.     

Effect of tensile strain rate on the mechanical properties of constrained-uniaxially and simultaneous-biaxially drawn poly(ethylene terephthalate) sheets

The dependency of the mechanical properties (Young's modulus, yield strength, breaking strain, and breaking energy) of preoriented poly(ethylene terephthalate) (PET) sheets on the tensile deformation speeds was examined and discussed in relation to changes of density and birefringence. The procedures for preorientation were constrained-uniaxially (CU) and simultaneous-biaxially (SB) drawings at 65°C. The performance characteristics of the present tensile testing at room temperature were obtained over a wide range of extension rates (1.7 × 10^?4?13.1 m/s = 0.29–2.3 × 10⁴%/s) without changing the mode of deformation and the shape of the test pieces. The CU drawn PET is strain-rate-independent and mechanically superior in structure in the preextended direction with draw ratio λ > 2.5. In the SB drawn PET such a structure comes into existence at λ > 3, which has, furthermore, no dependency on draw direction (mechanically isotropic). The draw ratio of the latter case corresponded to the birefringence (?Δn/d) of about 5 × 10^?2. These results imply a possibility of producing the strain rate (from low to impact speeds) independent, anisotropy-free, and mechanically superior molded products of PET if adequate extrusion or blow molding methods which induce multiaxial orientation with ?Δn/d > 5 × 10^?2 are developed.