Investigation on the oxidation of surface layers of polyolefins treated with corona discharge

The results of an X-ray photoelectron spectroscopic investigation of the oxidation of surface layers of low-density polyethylene (LDPE) and biaxially oriented polypropylene (BOPP) films are presented. The analysis was performed using different take-off angles, namely 10°, 30°, and 90°; thus, the depths of the examined layers were 0.6, 1.9, and 3.7 nm, respectively. It was found that the course of the oxidation process in the surface layers was similar for both polymer films. However, for treatment energies lower than 5 kJ/m², the extent of the oxidation was higher for the LDPE film, whereas for energies above this value, the BOPP film was more oxidized. As detected by X-ray photoelectron spectroscopy (XPS), desorption of oxygen from the film surface occurs for both polymers during the treatment.     

Adhesion of extrusion‐coated polymer sealing layers to a fiber‐based packaging material with an atomic layer deposited aluminum oxide surface coating

Adhesion of extrusion‐coated polymer sealing layers on an atomic layer deposited (ALD) aluminum oxide (Al₂O₃) surface coating was investigated with a view to gain information on the applicability of ALD deposited barrier layers in fiber‐based packaging materials. The polymers used for the sealing layer were low density polyethylene (LDPE), polyethylene terephthalate (PET), and polylactide (PLA). They were extrusion‐coated onto the ceramic side of paper/PET/Al₂O₃ substrates, where the Al₂O₃ layer was a few tens of nanometers thick. According to the results, good adhesion was obtained for LDPE coating, whereas the other coatings showed a considerable lack of adhesion. Presumably, the oxidation faced by LDPE in the air gap of the extrusion‐coating process was able to create an extensive number of reactive sites that strongly bonded with the hydroxyl groups on the oxide surface of the substrate. With the PET and PLA coatings, such oxidation did not occur and the adhesion obtained remained at a relatively poor level. With all of the coatings, the adhesion levels were improved using corona discharge equipment as a pretreatment prior to the extrusion‐coating process. POLYM. ENG. SCI., 52:1985–1990, 2012. © 2012 Society of Plastics Engineers     

Enhanced dielectric properties of sandwich-structured biaxially oriented polypropylene by grafting hyper-branched aromatic polyamide as surface layers

This work represents multilayer films with sandwich structure by grafting hyper-branched aromatic polyamide (HBP) on both sides of biaxially oriented polypropylene (BOPP) (HBP BOPP HBP). BOPP serves as the middle layer to offer high breakdown strength and HBP acts as surface layers to boost the dielectric constant. As a result, the dielectric constant increases significantly from 2.2 of control BOPP to 5.5 (almost increased 1.5 times) after grafting 2.06 μm HBP surface layers, while the dielectric loss still remains at a very low level (<0.03). In addition, all HBP BOPP HBP sandwich-structured films show higher charge energy density than that of unmodified BOPP. For instance, the discharge energy density of HBP BOPP HBP (1-20-1) film is up to 2.38 J/cm³ at an applied electric field of 400 kV/mm, which increases about 36% over that of pure BOPP (i.e., 1.75 J/cm³). Meanwhile, charge–discharge efficiency retains about 90%. This work offers a simple strategy to fabricate polymer-based high performance dielectric composites.     

Surface degradation and hydrophobic recovery of polyolefins treated by air corona and nitrogen atmospheric pressure glow discharge

The surface degradation and production of low molecular weight oxidized materials (LMWOM) on biaxially oriented polypropylene (BOPP) and low‐density polyethylene (LDPE) films was investigated and compared for two different dielectric barrier discharge (DBD) treatment types, namely air corona and nitrogen atmospheric pressure glow discharge (N₂ APGD). Contact angle measurements, X‐ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) analyses were performed in conjunction with rinsing the treated films in water. It is shown that N₂ APGD treatments of both polyolefins result in much less surface degradation, therefore, allowing for a significantly higher degree of functionalization and better wettability. Hydrophobic recovery of the treated films has also been studied by monitoring their surface energy (γ_s) over a period of time extending up to several months after treatment. Following both surface modification techniques, the treated polyolefin films were both found to undergo hydrophobic recovery; however, for N₂ APGD modified surfaces, γ_s ceases to decrease after a few days and attains a higher stable value than in the case of air corona treated films. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1291–1303, 2004     

Radiation‐induced graft copolymerization of acrylic acid/acrylonitrile onto LDPE and PET films and its biodegradability

Graft copolymerization of acrylic acid/acrylonitrile (AAc/AN) comonomer onto low‐density poly(ethylene) (LDPE) and poly(ethylene terephthalate) (PET) films using direct radiation grafting technique has been investigated. The effect of different reaction conditions on the grafting yield was studied. The structure of the grafted films at different compositions was characterized by FTIR, TGA, SEM, and XRD. Biodegradation of grafted LDPE and PET was investigated by burial method in two types of Egyptian soils (agricultural and desert soils). The bacteria responsible for biodegradation were isolated and characterized, and the capacities for the growth on these polymers as substrates were compared. The isolates from agricultural soil were characterized as Pseudomonas, Alcaligenes, Bacillus, Proteus, and Enterobacter, whereas the isolates from desert soil were characterized as Alcaligenes, Bacillus, and Pseudomonas. The highest degradation rate was found to be achieved using agricultural soil. It is found that the isolated strains belonging to the genus Pseudomonas were mainly responsible for the degradation of both polymers. It has also been found that the increase of AAc ratio in the composition increases the hydrophilicity of the films and the degradation rate. PET polymer is generally found to be more resistant to the biodegradation than LDPE in the two types of soils tested. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Artificial ageing of low density polyethylene film containing chemically bound UV - stabilizer

This paper deals with photostabilization of low density polyethylene films (LDPE) grafted with the UV-stabilizer 2-hydroxy-4-(3-methacryloxy-2-hydroxy-propoxy) benzophenone (HMB). The influence of grafting yield and the other grafting conditions upon photostabilization efficiency of LDPE films were then studied. The chemically bound monomer (HMB) was localized mainly near the surface of an LDPE film. The grafted LDPE film was exposed to an ultraviolet radiation source, and the degree of oxidation and other photooxidative changes were determined by transmission IR and ATR IR spectroscopy. Experimental results show that radiation grafting of a UV-stabilizer upon LDPE films is an efficient photostabilization method.     

Processing and characterization of multilayer films of poly(ethylene terephthalate) and surface-modified poly(tetrafluoroethylene)

Multilayer films were prepared from poly(tetrafluoroethylene) (PTFE) and poly(ethylene terephthalate) (PET) films together with using an adhesion promoting layer (tie-layer) consisting of ethylene-methyl acrylate-glycidyl methacrylate (E-MA-GMA) terpolymer and low density polyethylene (LDPE) blend. Na/naphthalene treatment and subsequent acrylic acid grafting were applied on the surfaces of PTFE for chemical modification. FT-IR spectroscopy, XPS analysis and surface energy measurements were performed to characterize the modified PTFE films. The analyses showed defluorination and oxidation of PTFE surface, and supported the acrylic acid grafting. The surface energy of modified surfaces enhanced with respect to unmodified one, which promoted adhesion. The multilayers were subjected to T-peel tests to measure the adhesion strength between PET and modified PTFE. Peel strength between the films increased with increasing E-MA-GMA amount in the tie-layer. A proportional dependence of peel strength on Na/naphthalene treatment time was observed for multilayers containing acrylic acid grafted or ungrafted PTFE. From SEM analysis, it was observed that the texture of the PTFE surface after modifications became rougher when compared to untreated PTFE. The peeled surfaces were also analyzed by SEM. The micrographs evidence that the energy absorbing mechanism is the plastic deformation of the tie-layer, which is responsible for obtaining high peel strengths.     

Effect of pro‐oxidants on biodegradation of polyethylene (LDPE) by indigenous fungal isolate,Aspergillus oryzae

Proxidant additives represent a promising solution to the problem of the environment contamination with polyethylene film litter. Pro‐oxidants accelerate photo‐ and thermo‐oxidation and consequent polymer chain cleavage rendering the product apparently more susceptible to biodegradation. In the present study, fungal strain, Aspergillus oryzae isolated from HDPE film (buried in soil for 3 months) utilized abiotically treated polyethylene (LDPE) as a sole carbon source and degraded it. Treatment with pro‐oxidant, manganese stearate followed by UV irradiation and incubation with A. oryzae resulted in maximum decrease in percentage of elongation and tensile strength by 62 and 51%, respectively, compared with other pro‐oxidant treated LDPE films which showed 45% (titanium stearate), 40% (iron stearate), and 39% (cobalt stearate) decrease in tensile strength. Fourier transform infrared (FTIR) analysis of proxidant treated LDPE films revealed generation of more number of carbonyl and carboxylic groups (1630–1840 cm⁻¹ and 1220–1340 cm⁻¹) compared with UV treated film. When these films were incubated with A. oryzae for 3 months complete degradation of carbonyl and carboxylic groups was achieved. Scanning electron microscopy of untreated and treated LDPE films also revealed that polymer has undergone degradation after abiotic and biotic treatments. This concludes proxidant treatment before UV irradiation accelerated photo‐oxidation of LDPE, caused functional groups to be generated in the polyethylene film and this resulted in biodegradation due to the consumption of carbonyl and carboxylic groups by A. oryzae which was evident by reduction in carbonyl peaks. Among the pro‐oxidants, manganese stearate treatment caused maximum degradation of polyethylene. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

An investigation of optical clarity and crystalline orientation in polyethylene tubular film

A study of the crystalline orientation, light transmission, and surface roughness of polyethylene tubular film prepared in our laboratories is presented. The present studies were primarily carried out on low-density (LDPE) and linear-low-density (LLDPE) polyethylene films. The optical properties of a few films of high-density polyethylene (HDPE) prepared for a previous study of morphology were characterized for comparison to the LDPE and LLDPE films. Wide angle X-ray diffraction and birefringence were used to characterize orientation. Both the LDPE and LLDPE films exhibited crystalline texture in which the b-axes tended to be perpendicular to the film surface and the a-axes had some tendency to align with the machine direction. The c-axes tended to be concentrated in the plane of the film with nearly equal biaxial orientation with respect to the machine and transverse directions. Little variation in the crystalline orientation was found with changes of process conditions in the range studied. Birefringence results indicate that the amorphous regions developed an orientation in which the chains tend to be normal to the film surface. The majority of light scattering from these films and a series of HDPE films was from the surface and not from the film interior. The transmission coefficient for the surface contribution was found to be a monotonic decreasing function of the standard deviation of the surface height obtained from surface profiles measured by profilometer. The surface asperites were largest for the HDPE and smallest for the LDPE samples. The intensity of both the surface and interior contributions to the scattering increased with increasing frostline height, i.e., a slower cooling rate. As draw-down ratio and blow-up ratio increase the scattering contribution from the film interior decreases but the contribution from the surface increases somewhat. These effects are discussed in terms of the changes in crystalline morphology and surface roughness produced by flow defects generated during extrusion.     

Control of well‐defined crater structures on the surface of biaxially oriented polypropylene film by adding nucleators

While it is common to add anti‐blocking agents to biaxially oriented polypropylene (BOPP) films for general use in order to prevent blocking against each other, the technology of crater‐like film surface roughness formed on the BOPP films without any additives is well known in the industrial BOPP film areas. Numerous studies have been reported on the crater‐like film surface roughness on the BOPP films since the 1980s, but its formation mechanism and the controlling method of the crater‐like film surface roughness are yet to be clarified. In our previous reports, we presented a new hypothesis of crater formation mechanism from a new point of view on sheet morphology and crater shape on the BOPP film surface. It was strongly influenced by the crystal grain shape in the surface layer of PP sheet. In this report, it was clarified that a nucleator has a big influence on the formation of the crystal grains in the surface layer of PP sheets and on the formation of craters. In addition, craters did not form on the BOPP films stretched from the sheet of which the skin layer with crystal grain was shaved, even though β crystal still remained. It was clarified that the crystal grain is trans‐crystal from the observation using TEM. Therefore, it is concluded that the existence of β crystals in the surface layer of PP sheets is not essential in order to produce craters on BOPP films, but trans‐crystals are necessary to form the craters. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3555–3564, 2013     

Some Effects of Corona Discharge Treatment of Biaxially-Oriented Polypropylene Film

The effects of the unit corona-treatment energy on the contact angle of various liquids, on the surface free energy, on the extent of oxidation of a surface layer, and on the adhesion of acrylic adhesive were studied using a biaxially-oriented polypropylene (BOPP) film. The surface free energy was determined with the van Oss-Chaudhury-Good (VCG) approach as well as with the wettability method. The extent of oxidation of the surface layer of the corona-treated BOPP film was evaluated with X-ray photoelectron spectroscopy. The adhesion strength of joints between the BOPP film and the acrylic adhesive was measured using the 180°-peel test.

In the range of the unit corona-treatment energy up to 1.2 kJ/m², a rapid increase in the surface free energy with the treatment energy is observed. In the range above that value, the surface free energy rises relatively slowly. The extent of oxidation of the surface layer and the adhesion strength of joints between the BOPP film and the acrylic adhesive are approximately in direct proportion to the unit energy of the corona treatment. A five-fold growth of the adhesion strength of the studied joints within the examined range of the treatment energy was found.     

Surface photografting of low-density polyethylene films and its relevance to photolamination

Surface modifications of pristine and ozone-pretreated low-density polyethylene (LDPE) films were carried out via UV-induced graft copolymerization with a photoinitiator-containing, epoxy-based commercial monomer (DuPont Somos? 6100 for solid imaging and optical lithography) and also with the photoinitiator-free acrylic acid (AAc). The chemical composition and microstructure of the graft copolymerized surfaces were studied by angle-resolved X-ray photoelectron spectroscopy (XPS). The concentration of surface grafted polymer increased with the UV illumination time and the monomer concentration. For LDPE films graft copolymerized with the epoxy-based monomer, surface chain rearrangement was not observed or was less well pronounced, due to the partial crosslinking of the grafted chains. Simultaneous photografting and photolamination between two LDPE films, or between a LDPE film and a poly(ethylene terephthalate) (PET) film, in the presence of either monomer system, were also investigated. The photolamination rates and strengths depend on the ozone pretreatment time, the UV illumination time, and the UV wavelength, as well as on the nature of the substrate materials. A shear adhesion strength approaching 150 N/cm² could be achieved with either monomer system, provided that the polymer films were pretreated with ozone. The failure mode of the photolaminated surfaces was cohesive in nature in the case of the photoinitiator-containing epoxy monomer, but was either cohesive or adhesional in nature (depending on the substrate assembly) in the case of the photoinitiator-free AAc monomer.     

Study of crater structure formation on the surface of biaxially oriented polypropylene film

Biaxially oriented polypropylene (BOPP) film accounts for a large amount of polypropylene since it is well suited for food packaging films or industrial films, because of its high performance in terms of mechanical and optical properties. Recently machine speed has been increasing to obtain higher production rate and film thickness has become thinner to reduce the environmental load. To meet the demands, many researchers have been investigating stretchability of PP by connecting the stretching force at the yield point and crystalline structure. Many other studies have been conducted regarding the surface structure of BOPP. Although there were some cases that crater‐like film surface roughness was formed on BOPP films, the formation mechanism of craters has not been clarified. In this report, new hypothesis of the crater‐like film surface roughness formation mechanism is proposed by observing the transformation of crater from sheet to BOPP film and by investigating the relationship between the stress–strain curve and surface roughness change. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nanolayer enhancement of biaxially oriented polypropylene film for increased gas barrier

An order of magnitude improvement in the oxygen barrier of biaxially oriented polypropylene (BOPP) films was achieved using a layer-multiplying, forced assembly process. The improvement was achieved without sacrificing clarity and toughness of the films. Sheets with 33 alternating layers of polypropylene (PP) (17 layers) and poly(?-caprolactone) (PCL) (16 layers) were coextruded using layer-multiplication and two thick PP skins were added to the multilayered core as the last step in the continuous coextrusion process. The sheets were subsequently biaxially oriented to draw ratios from 4 × 4 to 6 × 6. Biaxial orientation at elevated temperature reduced the thickness of the melted PCL layers from the microscale to the nanoscale, which created 2-dimensional confinement for subsequent crystallization of the PCL layers. It was anticipated that the PCL layers would recrystallize as highly oriented, in-plane lamellae that would resemble single crystals. However, the PCL lamellae were oriented perpendicular to the film surface, which actually facilitated oxygen permeation through the PCL layers and increased the oxygen permeability of the oriented films. Crystallization as on-edge lamellae was attributed to nucleation by the polypropylene surface. However, the surface nucleation was prevented by inserting buffer polystyrene (PS) layers in between the PCL and PP layers. In this case, the PCL lamellae were oriented in-plane. With the very high aspect ratio lamellar crystals oriented perpendicular to the flux direction, the permeation pathway of oxygen became very tortuous and the oxygen barrier was significantly improved.     

Protonation of polyaniline by surface-functionalized polymer substrates

The protonation of solution-coated emeraldine (EM) base by sulfonic and carboxylic acid groups on surface-functionalized low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP), poly(ethylene terephthalate) (PET), and polytetrafluoroethylene (PTFE) films were characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) spectroscopy, and conductivity measurements. Surface functionalizations were achieved by sulfonation (for LDPE, HDPE, PP, and PET), by hydrolysis (for PET), and by near-UV-light-induced surface graft copolymerization with the Na salt of styrene sulfonic acid and acrylic acid (for all substrates). The efficiency of surface functionalization by graft copolymerization is substantially enhanced for substrates pretreated with O₃ or Ar plasma. Protonation levels of 50% can be readily achieved for EM coated on sulfonic acid, but not carboxylic acid, functionalized surfaces. The extent of protonation, however, is also dependent on the microstructures of the modified substrate surfaces. In all cases, charge transfer interactions between the EM layer and the functionalized substrates readily result in good adhesion of the electroactive polymer on the polymer substrates to give rise to conductive surface structures. © 1995 John Wiley & Sons, Inc.     

Some Effects of Corona Discharge Treatment of Biaxially-Oriented Polypropylene Film

The effects of the unit corona-treatment energy on the contact angle of various liquids, on the surface free energy, on the extent of oxidation of a surface layer, and on the adhesion of acrylic adhesive were studied using a biaxially-oriented polypropylene (BOPP) film. The surface free energy was determined with the van Oss-Chaudhury-Good (VCG) approach as well as with the wettability method. The extent of oxidation of the surface layer of the corona-treated BOPP film was evaluated with X-ray photoelectron spectroscopy. The adhesion strength of joints between the BOPP film and the acrylic adhesive was measured using the 180°-peel test.

In the range of the unit corona-treatment energy up to 1.2 kJ/m², a rapid increase in the surface free energy with the treatment energy is observed. In the range above that value, the surface free energy rises relatively slowly. The extent of oxidation of the surface layer and the adhesion strength of joints between the BOPP film and the acrylic adhesive are approximately in direct proportion to the unit energy of the corona treatment. A five-fold growth of the adhesion strength of the studied joints within the examined range of the treatment energy was found.     

Surface oxidation of low‐density polyethylene films to improve their susceptibility toward environmental degradation

Polyethylene wastes, particularly as films, have accumulated over the last several decades resulting in a major visual litter problem. The aim of this study was to investigate the ability of chemical reagents to oxidize the low‐density polyethylene (LDPE) film surface to increase their susceptibility toward photodegradation and thermal degradation. Three chemical agents, namely, potassium permanganate, potassium persulfate, and benzoyl peroxide, were used to oxidize the film surface to generate chromophoric groups, such as carbonyl groups, which are the main reason for the enhanced environmental degradation of photolytic polymers, such as ethylene–carbon monoxide and ethylene–vinyl ketone copolymers. For the chemical treatment, LDPE films of 70 ± 5 μm thickness were prepared by a film‐blowing technique and subsequently reacted with the aforementioned oxidizing agents. To aid the oxidation process, the reaction with potassium persulfate and potassium permanganate was performed under microwave irradiation heating. In the case of benzoyl peroxide aided oxidation, the films were subjected to repeated coating–heating treatments up to a maximum of 10 cycles. The treated films were subjected to accelerated aging, that is, xenon‐arc weathering and air‐oven aging (at 70°C), for extended time periods. The chemical and physical changes induced as a result of aging were followed by the monitoring of changes in the mechanical, structural, and thermal properties. The results indicate that the surface‐oxidized LDPE films exhibited enhanced susceptibility toward degradation; however, the extent was reduced as compared to photolytic or other degradable compositions. The ability of the chemicals to initiate degradation followed the order potassium persulfate < potassium permanganate < benzoyl peroxide. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Surface modification of low‐density polyethylene films by a novel solution base chemical process

The surfaces of the film samples of low‐density polyethylene (LDPE) were chemically modified with an aqueous solution of ammonium persulphate solution (0.1 M) and Fe (NO₃)_3,9H₂O (0.2 M) heated to about 80°C for 2.5 h for which polar groups like ? OH, 〉CO, ? COOH, etc., were generated on the surface of the LDPE films. The modified films were analyzed by Infrared (IR) spectroscopy, Scanning Electron Microscopy (SEM), and Electron Spectroscopy for Chemical Analysis (ESCA). New surface of LDPE produced by this modification, demonstrated reasonable oxygen incorporation on the surface of polymer films through chemical bonding, which is essential for adhesion processes. For these chemical changes the extent of printability and adhesion. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3046–3051, 2004     

Immobilization of antioxidant on nanosilica and the antioxidative behavior in low density polyethylene

Nanosilica was firstly modified with an aminosilane coupling agent (AEAPS) and then reacted with the reactive antioxidant, 3,5-di-tert-butyl-4-hydroxycinnamic acyl chloride (AO-Cl), to form a nanosilica-immobilized antioxidant, AO-AEAPS-silica. FT-IR, XPS and TGA measurements confirmed that the reactive antioxidant was chemically immobilized onto the nanosilica surface. SEM observation showed that the nanosilica-immobilized antioxidant was homogeneously dispersed into the matrix of low density polyethylene (LDPE). It has been found that the antioxidative efficiency of AO-AEAPS-silica was superior to the corresponding low molecular counterpart (AO), based on the measurement of the oxidation induction time (OIT) of the LDPE/AO-AEAPS-silica and the LDPE/AO compounds containing equivalent antioxidant component. The release of the antioxidant from LDPE films was evaluated by monitoring the OIT change upon water extraction, demonstrating that AO-AEAPS-silica retained high stability against migration.     

Fast space charge behavior in heat‐treated polypropylene films

In this study, the characterization of the short‐circuit current within hundreds of nanoseconds is proposed to study the effect of heat treatment on fast space charge behavior in the polarized biaxially oriented polypropylene (BOPP) films. The BOPP films were cooled either quickly or slowly during the sample preparation. The damped oscillating feature was found in the short‐circuit current of all the polarized film samples, but the periods of the oscillating current for the samples prepared by fast cooling rate decrease faster. Bipolar space charge injection in the polarized BOPP films was observed by the thermal pulse (TP) measurement. The variation feature of the short‐circuit current was considered to be associated with the varying fast space charge behavior, which depended on the varying structural traps modified by the heat treatment during the sample preparation. The sample subjected to fast cooling process was with relatively shallow trap level revealed by the thermally stimulated current method, which led to higher mobility of the escaping charge in the sample. The TP measurements were utilized to analyze space charge features in the polarized BOPP films. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42235.