Polyol-Derived Alkoxide/Hydroxide Base Catalysts I. Production

A metal methoxide is more expensive than a metal hydroxide and dissolves in methanol releasing a methoxide ion without producing water. The methoxide ion has a higher reaction rate making it more preferred for industrial biodiesel production. This study describes the preparation of alkoxide catalysts from metal hydroxides and non-volatile, non-toxic polyols. Heating aqueous solutions of metal hydroxides and different polyols (1,2-propanediol, 1,3-propanediol, glycerol, xylitol and sorbitol) under vacuum yielded polyol-derived alkoxide base catalysts (PDABC). Comparison of the drying process for respective sodium hydroxide-polyol combinations at two mole ratios of sodium hydroxide to polyol showed that drying at 2:1 mole ratio (metal hydroxide to polyol) was more efficient than that of 3:1. Dehydration of alkaline solutions containing three or more hydroxyl groups (glycerol, sorbitol and xylitol) was faster than drying similar solutions of diols. The empirical formula determined confirmed that the resulting powders contained mono-sodium substituted alkoxides at 1:1, 2:1 and 3:1 (sodium hydroxide: polyol) mole ratio. Fatty acid methyl esters were prepared from canola oil and methanol using glycerol sodium alkylate as a catalyst. The conversion yield of oil to methyl ester was greater than 99 %.     

Optimization of transesterification for methyl ester production from chicken fat

In this study, low cost feedstock chicken fat was used to produce methyl ester. After reducing the free fatty acid level of the chicken fat less than 1%, the transesterification reaction was completed with alkaline catalyst. Potassium hydroxide, sodium hydroxide, potassium methoxide and sodium methoxide were used as catalyst and methanol was used as alcohol for transesterification reactions. The effects of catalyst type, reaction temperature and reaction time on the fuel properties of methyl esters were investigated. The produced chicken fat methyl esters were characterized by determining their viscosity, density, pour point, flash point, acid value, methanol content, heat of combustion value, total-free glycerin, mono-di-tri glycerides, copper strip corrosion and ester yield values. The measured fuel properties of the chicken fat methyl ester met EN 14214 and ASTM D6751 biodiesel specifications when using potassium hydroxide and sodium hydroxide catalysts with high ester yield.     

Evaluation of biodiesel obtained from cottonseed oil

Esters from vegetable oils have attracted a great deal of interest as substitutes for petrodiesel to reduce dependence on imported petroleum and provide a fuel with more benign environmental properties. In this work biodiesel was prepared from cottonseed oil by transesterification with methanol, using sodium hydroxide, potassium hydroxide, sodium methoxide and potassium methoxide as catalysts. A series of experiments were conducted in order to evaluate the effects of reaction variables such as methanol/oil molar ratio (3:1–15:1), catalyst concentration (0.25–1.50%), temperature (25–65 °C), and stirring intensity (180–600 rpm) to achieve the maximum yield and quality. The optimized variables of 6:1 methanol/oil molar ratio (mol/mol), 0.75% sodium methoxide concentration (wt.%), 65 °C reaction temperature, 600 rpm agitation speed and 90 min reaction time offered the maximum methyl ester yield (96.9%). The obtained fatty acid methyl esters (FAME) were analyzed by gas chromatography (GC) and ¹H NMR spectroscopy. The fuel properties of cottonseed oil methyl esters (COME), cetane number, kinematic viscosity, oxidative stability, lubricity, cloud point, pour point, cold filter plugging point, flash point, ash content, sulfur content, acid value, copper strip corrosion value, density, higher heating value, methanol content, free and bound glycerol were determined and are discussed in the light of biodiesel standards such as ASTM D6751 and EN 14214.     

The pseudo-single-phase,base-catalyzed transmethylation of soybean oil

The base-catalyzed transmethylation of soybean oil has been studied under conditions whereby the reaction starts as a single phase, but later becomes two phases as glycerol separates. Methanol/oil molar ratios of 6∶1 were used at 23°C. The catalysts were sodium hydroxide (0.5, 1.0, and 2.0 wt%), potassium hydroxide (1.0 and 1.4 wt%), and sodium methoxide (0.5, 1.0, and 1.35 wt%), all concentrations being with respect to the oil. Oxolane (tetrahydrofuran) was used to form a single reaction phase. The reactions deviated from homogeneous kinetics as glycerol separated, taking with it most of the catalyst. When 1.0 wt% sodium hydroxide was used, the methyl ester content reached 97.5 wt% after 4 h, compared with 85–90 wt% in the two-phase reaction. Sodium hydroxide (1.0 wt%), sodium methoxide (1.35 wt%), and potassium hydroxide (1.4 wt%) gave similar results, presumably because the same number of moles was used. The ASTM biodiesel specification for chemically bound glycerol was achieved after only 3 min when 2.0 wt% sodium hydroxide was used. However, the standard was not achieved after 4 h when 1.0 wt% sodium hydroxide was used, the MG content being 1.1–1.6 wt%. The use of 2.0 wt% catalyst is commercially impractical.     

Transesterification of neat and used frying oil: Optimization for biodiesel production

In this study, the characteristics and performance of three commonly used catalysts used for alkaline-catalyzed transesterification i.e. sodium hydroxide, potassium hydroxide and sodium methoxide, were evaluated using edible Canola oil and used frying oil. The fuel properties of biodiesel produced from these catalysts, such as ester content, kinematic viscosity and acid value, were measured and compared. With intermediate catalytic activity and a much lower cost sodium hydroxide was found to be more superior than the other two catalysts. The process variables that influence the transesterification of triglycerides, such as catalyst concentration, molar ratio of methanol to raw oil, reaction time, reaction temperature, and free fatty acids content of raw oil in the reaction system, were investigated and optimized. This paper also studied the influence of the physical and chemical properties of the feedstock oils on the alkaline-catalyzed transesterification process and determined the optimal transesterification reaction conditions that produce the maximum ester content and yield.     

Glycerolysis of Soybean Oil with Crude Glycerol Containing Residual Alkaline Catalysts from Biodiesel Production

The glycerolysis reaction of soybean oil was evaluated using crude glycerol obtained from the transesterification of soybean oil with methanol, catalyzed by sodium methoxide and sodium hydroxide, without any purification step other than the methanol removal. Crude glycerol with the lower content of remaining inorganic catalyst produced the highest concentration of monoglycerides (about 42%). The effect of the addition of water on the glycerolysis reaction was analyzed, evidencing a low formation rate of products in the first stages of the reaction due to the transformation of the inorganic catalyst to soaps, which are weaker bases. The sample of crude glycerol that led to the best results was evaluated at several temperatures. It was observed that the reaction with crude glycerol exhibits a lower formation rate of monoglycerides at low temperatures (160 and 180 °C) compared with the reaction with pure glycerol and catalyzed with NaOH. This behavior was explained by the lower activity of the soaps present in the crude glycerol respect to the inorganic base. Above 200 °C the reaction is very fast and the monoglycerides formed are consumed to produce diglycerides.     

Tri-potassium phosphate as a solid catalyst for biodiesel production from waste cooking oil

Transesterification of waste cooking oil with methanol, using tri-potassium phosphate as a solid catalyst, was investigated. Tri-potassium phosphate shows high catalytic properties for the transesterification reaction, compared to CaO and tri-sodium phosphate. Transesterification of waste cooking oil required approximately two times more solid catalyst than transesterification of sunflower oil. The fatty acid methyl ester (FAME) yield reached 97.3% when the transesterification was performed with a catalyst concentration of 4 wt.% at 60 °C for 120 min. After regeneration of the used catalyst with aqueous KOH solution, the FAME yield recovered to 88%. Addition of a co-solvent changed the reaction state from three-phase to two-phase, but reduced the FAME yield, contrary to the results with homogeneous catalysts. The catalyst particles were easily agglomerated by the glycerol drops derived from the homogeneous liquid in the presence of co-solvents, reducing the catalytic activity.     

间苯二甲酸丙二醇酯-5-磺酸钠的合成工艺

以间苯二甲酸二甲酯-5-磺酸钠(SIPM)、1,3-丙二醇(1,3-PDO)为原料,采用酯交换法合成了间苯二甲酸丙二醇酯-5-磺酸钠(SIPP),并研究了催化剂种类及浓度、原料配比和反应温度对酯交换反应的影响。结果表明:通过工艺优化,当选择以钛酸四丁酯作为催化剂,其摩尔分数为0.1%(相对原料中SIPM的摩尔分数),1,3-PDO与SIPM的摩尔分数比为10.14∶1,反应温度为173℃时,酯交换反应速率较快且产物色泽良好。     

How is chemical interesterification initiated: Nucleophilic substitution or α-proton abstraction?

Esters of carboxylic acids including 2-methylhexanoic, 2-methylbutyric, 2,2-dimethyl-4-pentenoic, palmitic, and oleic acids were tested as substrates in methoxide-catalyzed interesterification and transesterification. The aliphatic acid esters participated in the ester-ester interchange upon addition of catalytic sodium methoxide. Their isopropyl esters also produced methyl esters on heating with sodium methoxide. The esters of α-methyl-substituted acids did not participate in the ester-ester interchange. Their isopropyl esters did not react with methoxide to produce methyl esters. However, upon addition of methanol with sodium methoxide, their methyl esters were produced. These results indicate that the first step in interesterification is possibly that methoxide abstracts the α-hydrogen of an ester to form a carbanion. Interesterification is then likely completed via a Claisen condensation mechanism involving the β-keto ester anion as the active intermediate. The β-keto ester anion contains positively charged ketone and acyl carbons that are active sites for nucleophilic attack by anions such as methoxide and glycerinate, which would produce a methyl ester or rearrange acyls randomly. On the other hand, transesterification is a nucleophilic substitution by methoxide at the acyl carbon in the presence of methanol.     

Transesterification of vegetable oil to biodiesel fuel using alkaline catalyst

Biodiesel is gaining more and more importance as an attractive fuel due to the depleting fossil fuel resources. Chemically biodiesel is monoalkyl esters of long chain fatty acids derived from renewable feed stock like vegetable oils and animal fats. It is produced by transesterification in which, oil or fat is reacted with a monohydric alcohol in presence of a catalyst to give the corresponding monoalkyl esters. This article reports experimental data on the production of fatty acid methyl esters from vegetable oils, soybean and cottonseed oils using sodium hydroxide as alkaline catalyst. The variables affecting the yield and characteristics of the biodiesel produced from these vegetable oils were studied. The variables investigated were reaction time (1-3 h), catalyst concentration (0.5-1.5 w/wt%), and oil-to-methanol molar ratio (1:3-1:9). From the obtained results, the best yield percentage was obtained using a methanol/oil molar ratio of 6:1, sodium hydroxide as catalyst (1%) and 60 ± 1 °C temperature for 1 h. The yield of the fatty acid methyl ester (FAME) was determined according to HPLC. The composition of the FAME was determined according to gas chromatography. The biodiesel samples were physicochemically characterized. From the results it was clear that the produced biodiesel fuel was within the recommended standards of biodiesel fuel.     

<Emphasis Type="Italic">In situ</Emphasis> alkaline transesterification: An effective method for the production of fatty acid esters from vegetable oils

The production of simple alkyl FA esters by direct alkali-catalyzed in situ transesterification of the acylglycerols (AG) in soybeans was examined. Initial experiments demonstrated that the lipid in commercially produced soy flakes was readily transesterified during agitation at 60°C in sealed containers of alcoholic NaOH. Methyl, ethyl, and isopropyl alcohols readily participated in the reaction, suggesting that the phenomenon is a general one. Statistical experimental design methods and response surface regression analysis were used to optimize reaction conditions, using methanol as alcohol. At 60°C, the highest yields of methyl ester with minimal contamination by FFA and AG were predicted at a molar ratio of methanol/AG/NaOH of 226∶1∶1.6 with an approximately 8-h incubation. An increase in the amount of methanol, coupled with a reduced alkali concentration, also gave high ester yields with low FFA and AG contamination. The reaction also proceeded well at 23°C (room temperature), giving higher predicted ester yields than at 60°C. At room temperature, maximal esterification was predicted at a molar ratio of 543∶1∶2.0 for methanol/AG/NaOH, again in 8 h. Of the lipid in soy flakes, 95% was removed under such conditions. The amount of FAME recovered after in situ transesterification corresponded to 84% of this solubilized lipid. Given the 95% removal of lipid from the soy flakes and an 84% efficiency of conversion of this solubilized lipid to FAME, one calculates an overall transesterification efficiency of 80%. The FAME fraction contained only 0.72% (mass basis) FFA and no AG. Of the glycerol released by transesterification, 93% was located in the alcoholic ester phase and 75 was on the post-transesterification flakes.     

Transesterification of sunflower oil over zeolites using different metal loading: A case of leaching and agglomeration studies

The aim of this study was to analyse the catalytic performance of several heterogeneous catalysts in the transesterification of sunflower oil with methanol. In order to characterize the different catalysts, nitrogen adsorption/desorption and CO₂ temperature programmed desorption were used. The transesterification of sunflower oil was carried out using three different zeolites: mordenite, beta and X, to determine the influence of the kind of zeolite on the methyl ester production. The influence of the metal incorporation technique was studied using both impregnation and ion-exchange methods. Also, the transesterification reaction was carried out using catalysts with different metal loading. Finally, zeolite X was agglomerated with a binder, sodium bentonite, to study how the presence of a binder could change the catalytic performance of the zeolite. A methyl ester content of 93.5 and 95.1 wt% was obtained at 60 °C employing zeolite X with or without sodium bentonite, respectively. All biodiesel synthesized were characterized using the standard UNE-EN 14214. A complete deactivation study was carried out in order to check the sodium leaching from the catalyst. The results supported the hypothesis of a homogeneous-like mechanism where the alkali methoxide species were leached out.     

Simple, high-efficiency synthesis of fatty acid methyl esters from soapstock

We report a simple method that efficiently esterifies the fatty acids in soapstock, an inexpensive, lipid-rich by-product of edible oil production. The process involves (i) alkaline hydrolysis of all lipid-linked fatty acid ester bonds and (ii) acid-catalyzed esterification of the resulting fatty acid sodium salts. Step (i) completely saponified all glycerides and phosphoglycerides in the soapstock. Following water removal, the resulting free fatty acid sodium salts were rapidly and quantitatively converted to fatty acid methyl esters (FAME) by incubation with methanol and sulfuric acid at 35°C and ambient pressure. Minimum molar reactant ratios for full esterification were fatty acids/methanol/sulfuric acid of 1∶30∶5. The esterification reaction was substantially complete within 10 min and was not inhibited by residual water contents up to ca. 10% in the saponified soapstock. The product FAME contained >99% fatty acid esters, 0% triglycerides, <0.05% diglycerides, <0.1% monoglycerides, and <0.8% free fatty acids. Free fatty acid levels were further reduced by washing with dilute sodium hydroxide. Free and total glycerol were <0.01 and <0.015%, respectively. The water content was <0.04%. These values meet the current specifications for biodiesel, a renewable substitute for petroleum-derived diesel fuel. The identities and proportions of fatty acid esters in the FAME reflected the fatty acid content of soybean lipids. Solids formed during the reaction contained 69.1% ash and 0.8% protein. Their sodium content indicated that sodium sulfate was the prime inorganic component. Carbohydrate was the predominant organic constituent of the solid.     

Response surface modeling and optimization of biodiesel production from Cynara cardunculus oil

Cardoon (Cynara cardunculus L.) is a perennial spontaneous thistle grown in Mediterranean countries and well adapted to marginal lands, recently considered as a non‐food energy crop. Their seeds contain 24% of oil (dry basis). In this study, modeling and optimization of the production of fatty acid methyl esters (FAME) from cardoon oil for biodiesel uses was performed at laboratory scale, via response surface methodology, following a central composite rotatable design. FAME were obtained by transesterification of crude cardoon oil with methanol in the presence of a catalyst (sodium methoxide) for 120 min. The temperature ranged from 26 to 94 °C, the amount of sodium methoxide varied between 0.12 and 2.5 wt‐% and the molar ratio methanol/oil from 0.95 : 1 to 11 : 1. The estimated yield of FAME (97%) was obtained after 30 min, at 52 °C, for a molar ratio of 6.4 : 1 and 1.4 wt‐% of catalyst. In laboratory‐scale model validation experiments, 94% of FAME yield was obtained after 30 min of reaction. Transesterification was performed in a 30‐L reactor, under previously optimized conditions: A yield of 88% FAME was obtained after 90 min of reaction time, due to mass transfer limitations. After purification, the biodiesel showed high quality according to DIN EN 14214 standard specifications.     

Effects of process variables for biodiesel production by transesterification

In this study, biodiesel production from various vegetable oils by transesterification was studied, to determine the optimum conditions. Experiments were carried out by using different kinds of catalysts (sodium hydroxide, potassium hydroxide, barium hydroxide, pyrolitic coke and wood ash) and feedstocks (corn oil, sunflower oil, soybean oil, olive pomace oil and cottonseed oil) at 65 °C and an agitation speed of 1000 rpm. The neutralization step with controlled pH was performed by treatment with phosphoric acid. An experimental design was used to evaluate the effects of the parameters such as types of vegetable oils, kinds of catalysts, reaction time, alcohol/oil volumetric ratio and amount of catalyst, on the methyl ester conversion. Using response surface methodology, a quadratic polynomial equation was obtained by multiple regression analysis. It was found that catalyst concentration was the most effective parameter. Sodium hydroxide and potassium hydroxide exhibited a superior catalytic behavior, whereas pyrolitic coke and wood ash had to be used in excess amount or for prolonged reaction times. Moreover, the properties such as viscosity, density, calorific value, acid value, and refractive index of the biodiesel were measured. The tri‐, di‐, monoacylglycerols and glycerol residuals in the methyl esters produced were also quantified by GC analysis.     

Synthesis and Optimization of 2-ethylhexyl Ester as Base Oil for Drilling Fluid Formulation

A stable ester was synthesized to overcome the ester hydrolysis problem during the drilling of oil or gas wells using a conventional ester-based drilling fluid. The thermal and hydrolytic stability of the produced ester was high owing to the transesterification method employed in this study. The reaction was performed using 2-ethylhexanol and methyl laureate esters in the presence of sodium methoxide as a catalyst. In order to obtain the optimum synthesis conditions, a response surface methodology (RSM) was appraised based on the central composite design (CCD). The optimum conditions were determined as follows: 0.6 wt.% catalyst, 70°C reaction temperature, 1:1.5 molar ratio, and 11.5 min of reaction time. The results of 77 wt.% 2-ethylhexyl ester (2-EH) illustrated a high agreement between the experimental and RSM models. The reaction product contained 77 wt.% 2-EH and 23% 2-ethylhexanol. The kinematic viscosity was 5 mm²/s at 40°C and 1.5 mm²/sec at 100°C; the specific gravity was 0.854, flash point was 170°C, and pour point was ?7°C. The produced product showed similar properties to the available commercial product. However, it was observed that the mud formulation using the synthesized base oil had superior rheological properties at 121°C.     

BIODIESEL PRODUCTION FROM PALM OIL VIA HETEROGENEOUS TRANSESTERIFICATION: OPTIMIZATION STUDY

Fatty acid methyl ester (FAME) prepared by transesterification process using a heterogeneous catalyst has received a lot of interest lately as it could overcome the limitations of the current commercial homogeneous catalytic process. Apart from that, palm oil, being the cheapest edible oil in the world, will always remain the most economical source of FAME. Therefore, in this study, the use of sulfated zirconia alumina as a heterogeneous catalyst to catalyze the transesterification of palm oil with methanol to FAME was carried out using design of experiment (DOE), specifically response surface methodology (RSM) based on four-variable central composite design (CCD) with α = 2. The transesterification process variables are reaction temperature (60–180°C), reaction period (1–5 h), methanol-to-oil ratio (4–12 mol mol^?1), and amount of catalyst (2–10 wt.%). In this study involving many multiple process variables, the design of experiment approach was found to be superior to the conventional one-variable-at-one-time approach. Interactions between variables were found to have significant effect on the yield of FAME. At the conditions of 3 h of reaction period, 127°C reaction temperature, methanol-to-palm oil ratio of 8, and 6 wt.% of catalyst, an optimum FAME yield of 83.3% can be obtained, indicating that sulfated zirconia alumina has potential as a heterogeneous catalyst for the production of FAME from palm oil.     

In situ production of fatty acid methyl ester from low quality rice bran: An economical route for biodiesel production

Low quality rice bran was used to produce fatty acid methyl ester (FAME) via in situ extraction, esterification and transesterification process. The effects of the acid and alkaline catalysts on the ester yield, esterification and transesterification process were studied. When 75 ml of absolute methanol, 150 ml of petroleum ether, 0.75 g of concentrated sulfuric acid and 0.71 g of sodium hydroxyl were used, 16.69% (w_FAME/w_{rice bran}) of FAME was obtained. The esterification rate and the transesterification rate reached 98.83% and 80.47%. Based on the proposed route, the production process of FAME (biodiesel) could be simplified and the production cost could be reduced.     

Biodiesel production using tetramethyl- and benzyltrimethyl ammonium hydroxides as strong base catalysts

In recent years, the acceptance of fatty acid methyl esters (biodiesel) as an alternative fuel has rapidly grown in EU. The most common method for biodiesel production is based on triglyceride transesterification to methyl esters with dissolved sodium hydroxide in methanol as catalyst. In this study, cottonseed oil and used frying oil were subjected to the transesterification reaction with tetramethyl ammonium hydroxide and benzyltrimethyl ammonium hydroxide as strong base catalysts. This work investigates the optimum conditions for biodiesel production using amine-based liquid catalysts. Biodiesel ester content was strongly related with the type of feedstock and the reaction variables, such as those of the catalyst concentration, methanol to oil molar ratio, and reaction time. The overall results suggested that the transesterification of cottonseed oil achieved high conversion rates with both catalysts, while the use of waste oil resulted in lower yields of methyl esters due to the possible formation of amides.     

Sulfated niobia supported on KIT-6 as a catalyst for transesterification of groundnut oil

Mesoporous 3D cubic KIT-6 was synthesised hydrothermally via organic template route. Different weight percentages (1, 2 and 3 %) of sulfated niobia were supported on KIT-6 by wet impregnation method and are abbreviated as 1SNK, 2SNK and 3SNK. The synthesised materials were characterized by XRD, FT-IR, BET surface area, DRS-UV Visible and TG techniques. The morphology of pure KIT-6 and SNKs were studied by SEM and HR TEM techniques. Experiments were performed with SNK catalysts for the transesterification reaction to convert the groundnut oil to fatty acid methyl ester (FAME). The product was confirmed by GC–MS. The parameters were optimized to increase the yield of FAME by altering the reaction temperature, reaction time, catalyst loading. Among the synthesized catalysts, 3SNK showed high activity than others due to high density of acid sites. Hence sulphated niobia supported KIT-6 may be better choice of catalyst for the conversion of groundnut oil to FAME.