A study on nanofiller effects of serpentine in polypropylene matrix

The nanocomposite materials were prepared using serpentine as filler and polypropylene (PP) as the matrix in the presence of maleic anhydride grafted polypropylene (PP‐g‐MA) compatibilizer. The melt intercalation was carried out following serpentine modification with a quaternary salt of cetyl‐trimethyl‐ammonium bromide. The structure of nanocomposites was shown by X‐ray diffraction (XRD) and transmission electron microscopy (TEM) studies. Thermal analysis performed by differential scanning calorimetry (DSC) demonstrated that the nanocomposites have higher percentage crystallinity when compared to neat PP. Dynamic mechanical analysis (DMA) revealed that the storage and loss moduli values of the nanocomposites are better than those of the matrix resin. Tensile properties of nanocomposites are significantly different from PP, e.g., the Young's modulus of the nanocomposite with 2 wt % serpentine and 6 wt % PP‐g‐MA (PP‐2,6Q) was found to be 2065 MPa, i.e., nearly 190.8% increase over the PP matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical properties of polypropylene/clay nanocomposites: Effect of clay content,polymer/clay compatibility,and processing conditions

In this work, polypropylene/clay nanocomposites with 0.5, 1, 3, and 5 wt % of montmorillonite (MMT) (unmodified clay) were prepared by intensive mixing at 50 rpm and 10 min of mixing. For the highest clay content (5 wt %), the initial materials or the processing conditions were changed to study their independent effect. On one hand, 10 wt % of PP‐graft‐MA (PP‐g‐MA) was incorporated or MMT was replaced by organomodified clays (C10A and C30B). On the other side, for the initial system, the speed of rotation (100 and 150 rpm) and the mixing time (5 and 15 min) were altered. In all cases, the state of the clay inside the matrix (DRX), the degree of dispersion in the micro (SEM) and nano (TEM) scales, and the rheological and mechanical properties were analyzed. It was found that the stiffness increased with clay content, whereas tensile and impact strength did not significantly change. Although intercalated structures were observed in the composites with unmodified clay, in the composites with modified clay or PP‐g‐MA, improved dispersion of clay in PP was found. The mechanical properties increased accordingly. The degree of dispersion of the filler in the matrix appeared to be unaffected by the changes in the processing conditions introduced. Finally, the elastic modulus was modeled by using an effective filler‐parameter model based on Halpin–Tsai equations, which also allowed estimating the relative degree of dispersion. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical,thermal and dynamic‐mechanical behavior of banana fiber reinforced polypropylene nanocomposites

Natural fiber‐reinforced nanocomposites based on polypropylene/nanoclay/banana fibers were fabricated by melt mixing in a twin‐screw extruder followed by compression molding in this current study. Maleic anhydride polypropylene copolymer (MA‐g‐PP) was used as a compatibilizer to increase the compatibility between the PP matrix, clay, and banana fiber to enhance exfoliation of organoclay and dispersion of fibers into the polymer matrix. Variation in mechanical, thermal, and physico‐mechanical properties with the addition of banana fiber into the PP nanocomposites was investigated. It was observed that 3 wt% of nanoclay and 5 wt% of MA‐g‐PP within PP matrix resulted in an increase in tensile and flexural strength by 41.3% and 45.6% as compared with virgin PP. Further, incorporation of 30 wt% banana fiber in PP nanocomposites system increases the tensile and flexural strength to the tune of 27.1% and 15.8%, respectively. The morphology of fiber reinforced PP nanocomposites has been examined by using scanning electron microscopy and transmission electron microscopy. Significant enhancement in the thermal stability of nanocomposites was also observed due to the presence of nanoclay under thermogravimetric analysis. Dynamic mechanical analysis tests revealed an increase in storage modulus (E′) and damping factor (tan δ), conforming the strong interaction between nanoclay/banana fiberand MA‐g‐PP in the fiber‐reinforced nanocomposites systems. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Development and characterization of green composites from bio‐based polyethylene and peanut shell

In the present work, different compatibilizers, namely polyethylene‐graft‐maleic anhydride (PE‐g‐MA), polypropylene‐graft‐maleic anhydride (PP‐g‐MA), and polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene‐graft‐maleic anhydride (SEBS‐g‐MA) were used on green composites derived from biobased polyethylene and peanut shell (PNS) flour to improve particle–polymer interaction. Composites of high‐density polyethylene/peanut shell powder (HDPE/PNS) with 10 wt % PNS flour were compatibilized with 3 wt % of the abovementioned compatibilizers. As per the results, PP‐g‐MA copolymer lead to best optimized properties as evidenced by mechanical characterization. In addition, best particle–matrix interface interactions with PP‐g‐MA were observed by scanning electron microscopy (SEM). Subsequently HDPE/PNS composites with varying PNS flour content in the 5–30 wt % range with PP‐g‐MA compatibilizer were obtained by melt extrusion and compounding followed by injection molding and were characterized by mechanical, thermal, and morphological techniques. The results showed that PNS powder, leads to an increase in mechanical resistant properties (mainly, flexural modulus, and strength) while a decrease in mechanical ductile properties, that is, elongation at break and impact absorbed energy is observed with increasing PNS flour content. Furthermore, PNS flour provides an increase in thermal stability due to the natural antioxidant properties of PNS. In particular, composites containing 30 wt % PNS powder present a flexural strength 24% and a flexural modulus 72% higher than the unfilled polyethylene and the thermo‐oxidative onset degradation temperature is increased from 232 °C up to 254 °C thus indicating a marked thermal stabilization effect. Resultant composites can show a great deal of potential as base materials for wood plastic composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43940.     

Polypropylene‐organoclay nanocomposite: Preparation,microstructure, and mechanical properties

A series of polypropylene (PP) nanocomposites containing 2, 4, and 6 wt % of an organophilic montmorillonite clay was prepared via direct melt mixing in the presence of maleic anhydride grafted polypropylene (PP‐g‐MAH) as compatibilizing agent. Microstructure characterization was performed by X‐ray diffraction analysis. Nanocomposites exhibited a 15 and 22% enhancement in tensile modulus and impact strength, respectively. The heat deflection temperature of PP nanocomposites was 36°C greater than for pure PP. Thermal and mechanical properties of nanocomposites were compared to properties of traditional PP‐talc and PP‐glass fiber composites. The results showed that the properties of nanocomposites improved compared to ordinary polypropylene composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The physical and mechanical properties of beta‐nucleated polypropylene/montmorillonite nanocomposites

Polypropylene (PP) and polypropylene/polypropylene‐g‐maleic anhydride/ organomontmorillonite (PP/PP‐g‐MA/OMMT) nanocomposites were modified with 0.05 to 0.3% (w/w) of the aryl amide β‐nucleator to promote the formation of hexagonal crystal modification (β‐phase) during melt crystallization. The nonisothermal crystallization behavior of PP, PP/PP‐g‐MA/OMMT and β‐nucleated PP/PP‐g‐MA/OMMT nanocomposites were studied by means of differential scanning calorimetry. Structure‐property relationships of the PP nanocomposites prepared by melt compounding were mainly focused on the effect and quantity of the aryl amide nucleator. The morphological observations, obtained from scanning electron microscopy, transmission electron microscopy and X‐ray diffraction analyses are presented in conjunction with the thermal, rheological, and mechanical properties of these nanocomposites. Chemical interactions in the nanocomposites were observed by FT‐IR. It was found that the β‐crystal modification affected the thermal and mechanical properties of PP and PP/PP‐g‐MA/OMMT nanocomposites, while the PP/PP‐g‐MA/OMMT nanocomposites of the study gained both a higher impact strength (50%) and flexural modulus (30%) compared to that of the neat PP. β‐nucleation of the PP/PP‐g‐MA/OMMT nanocomposites provided a slight reduction in density and some 207% improvement in the very low tensile elongation at break at 92% beta nucleation. The crystallization peak temperature (T_cp) of the PP/PP‐g‐MA/OMMT nanocomposite was slightly higher (116°C) than the neat PP (113°C), whereas the β‐nucleation increased the crystallization temperature of the PP/PP‐g‐MA/OMMT/aryl amide to 128°C, which is of great advantage in a commercial‐scale mold processing of the nanocomposites with the resulting lower cycle times. The beta nucleation of PP nanocomposites can thus be optimized to obtain a better balance between thermal and mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Polypropylene/clay nanocomposites: An innovative one‐pot process

This work discloses a novel one‐pot preparation method of polypropylene (PP)/clay nanocomposites with high degree of clay delamination and improved thermal, mechanical and rheological properties. The in situ simultaneous synthesis of carboxylate clay from native clay and ionomer of PP‐graft maleic anhydride (PP‐g‐MA) through trihydrate sodium acetate addition, combined with water injection in the extrusion process, appears to be a valuable alternative to the use of organoclay for producing PP/PP‐g‐MA/clay nanocomposites. The influence of PP‐g‐MA graft content, and of its ionomer form, onto the clay dispersion has been especially investigated. PP‐g‐MA of low graft content is compared to a home‐made highly grafted PP‐g‐MA synthesized in the presence of N‐bromosuccinimide (NBS). The nanocomposites prepared by combining the use of NBS‐mediated PP‐g‐MA, trihydrate sodium acetate and water injection exhibit the highest clay dispersion. Thermal, rheological, and mechanical properties of the nanocomposites have been measured. POLYM. COMPOS., 36:644–650, 2015. © 2014 Society of Plastics Engineers     

Effect of the molecular weight of maleated polypropylenes on the melt compounding of polypropylene/organoclay nanocomposites

Maleic anhydride grafted polypropylene (PP‐g‐MA) and organically modified clay composites were prepared in a plasticorder. PP‐g‐MAs, including Polybond PB3150, Polybond PB3200, Polybond PB3000, and Epolene E43, with a wide range of maleic anhydride (MA) concentrations and molecular weights were used. The structure was investigated with X‐ray diffraction (XRD) and transmission electron microscopy (TEM). PP‐g‐MA compatibilizers gave rise to similar degrees of dispersion beyond the weight ratio of 3/1, with the exception of E43, which had the highest MA content and the lowest molecular weight. The thermal instability and high melt index were responsible for the ineffective modification by E43. Furthermore, PP‐g‐MA with a lower molecular weight and a higher melt index had to be compounded at a lower mixing temperature to achieve a reasonable level of torque for clay dispersion. Polypropylene/organoclay nanocomposites were then modified with different levels of PP‐g‐MA compatibilizers with a twin‐screw extruder. The polypropylene/E43/clay system, as shown by XRD patterns and TEM observations, yielded the poorest clay dispersion of the compatibilizers under investigation. The curves of the relative complex viscosity also revealed a systematic trend with the extent of exfoliation and showed promise for quantifying the hybrid structure of the nanocomposites. The mechanical properties and thermal stability were determined by dynamical mechanical analysis and thermogravimetric analysis, respectively. Although PP‐g‐MA with a lower molecular weight led to better clay dispersion in the polypropylene nanocomposites, it caused deterioration in both the mechanical and thermal properties of the hybrid systems. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1667–1680, 2005     

An investigation on the mechanical and dynamic rheological properties of single and hybrid filler/polypropylene composites based on talc and calcium carbonate

Some results of experiments on the mechanical and rheological properties of mineral filled polypropylene were presented. Single filler and hybrid filler composites of talc and calcium carbonate (CaCO₃) were prepared in a co‐rotating twin‐screw extruder. The effect of filler type, filler content, and coupling agent on the mechanical and rheological properties of the polypropylene were studied. The coupling agent was maleic anhydride‐grafted polypropylene (PP‐g‐MA). It was found that the mechanical properties are affected by filler type, filler concentration, and the interaction between filler and matrix. The tensile strength of the composite is more affected by the talc while the impact strength is influenced mostly by CaCO₃ content. The elongation at break of PP/CaCO₃ composites was higher than that of PP/talc composites. The incorporation of coupling agent into PP/mineral filler composites increased the mechanical properties. Rheological properties indicated that the complex viscosity and storage modulus of talc filled samples were higher than those of calcium carbonate filled samples while the tan δ was lower. The rheological properties of hybrid‐filler filled sample were more affected by the talc than calcium carbonate. The PP‐g‐MA increased the complex viscosity and storage modulus of both single and hybrid composites. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

Nanocomposites of silica reinforced polypropylene: Correlation between morphology and properties

Polypropylene/fumed hydrophilic silica nanocomposites were prepared via melt mixing method using a single‐screw extruder. Comparative study with and without compatibilizing copolymer agent (maleic anhydride grafted polypropylene: PP‐g‐AM) was conducted. The obtained results were interpreted in terms of silica nanoparticle–silica nanoparticle and silica nanoparticle‐polymer interactions. These results have shown that the addition of nanofillers improves the properties of the nanocomposites. From transmission electron microscopy, it was found that agglomerations of silica particles into the PP matrix increased in average size with increasing silica contents, except in presence of the copolymer. Storage modulus values of the nanocomposites measured by dynamic mechanical thermal analysis were sensitive to the microstructure of the nanocomposites. Higher silica contents resulted in higher storage modulus, revealing that the material became stiffer. By adding the compatibilizer, a further increase of storage modulus was observed due to the finer dispersion of the filler in the matrix and the increased interfacial adhesion. Crystallization rates were found to increase with the increase of silica nanoparticles as well as PP‐g‐MA content. In addition, silica nanoparticles and the compatibilizing agent present centers of germination and nucleation of crystallites. Thus, the use of the coupling agent resulted in a further enhancement of mechanical properties of the nanocomposites due to the reduction of silica agglomeration. POLYM. ENG. SCI., 54:2187–2196, 2014. © 2013 Society of Plastics Engineers     

Combination of double‐modified clay and polypropylene‐graft‐maleic anhydride for the simultaneously improved thermal and mechanical properties of polypropylene

Double‐modified montmorillonite (MMT) was first prepared by covalent modification of MMT with 3‐aminopropyltriethoxysilane and then intercalation modification by tributyl tetradecyl phosphonium ions. The obtained double‐modified MMT was melt compounded with polypropylene (PP) to obtain nanocomposites. The dispersion of the double‐modified MMT in PP was found to be greatly improved by the addition of PP‐graft‐maleic anhydride (PP‐g‐MA) as a “compatibilizer,” whose anhydride groups can react with the amino groups on the surface of the double‐modified MMT platelets and thus improve the dispersion of MMT in PP. Fourier transform infrared, X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis, scanning electron microscopy, and tensile test were used to characterize the structure of the double‐modified MMT, morphology, and the thermal and mechanical properties of the nanocomposites. The results show that PP‐g‐MA promotes the formation of exfoliated/intercalated morphology and obviously increases the thermal properties, tensile strength, and Young's modulus of the PP/double‐modified MMT nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Ultrasound assisted continuous‐mixing for the preparation of PP/SEBS/OMMT ternary nanocomposites

Polypropylene (PP)/polystyrene‐block‐poly(ethylene‐co‐butylenes)‐block‐polystyrene (SEBS)/organo‐montmorillonite (OMMT) nanocomposites of varying concentrations of maleic anhydride‐grafted polypropylene (PP‐g‐MA) were prepared by continuous mixing assisted by ultrasonic oscillation. The structure and morphology of nanocomposites were investigated by X‐ray diffraction (XRD), transmission electron microscopy, and scanning electron microscopy. It was found that both PP‐g‐MA and ultrasonic oscillation could enhance the intercalation and exfoliation of OMMT in PP matrix. Meanwhile, the formation of PP could be induced by ultrasonic irradiation at a power of more than 540 W. Rheological properties including complex viscosity, storage, and loss modulus of nanocomposites were increased after adding PP‐g‐MA or ultrasonic treatment. The results of mechanical properties showed that PP‐g‐MA could improve the tensile strength and tensile modulus of nanocomposites, but with the sacrifice of impact strength. This problem could be improved by ultrasound due to the reduced particle size of SEBS. However, the mechanical properties would be reduced by ultrasonic treatment with higher intensity due to the polymer degradation. Therefore, the synergistic effect of both compatibilizer and ultrasound should account for the balance between toughness and stiffness of PP/SEBS/OMMT ternary nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41202.     

Preparation and morphological,thermal, and physicomechanical properties of polypropylene‐potato peel biocomposites

Potato peel powder (POPL), which is biodegradable, has been used as filler material in polypropylene (PP) matrix in varying concentration from 10 to 40% by weight to prepare biocomposites and investigated water absorption, physicomechanical and thermal properties. Scanning electron microscopy and X‐ray diffraction has been used for morphological characterization and crystallization studies. Flexural modulus of biocomposites increased by 40% compared with neat PP at 30% loading of POPL. Flexural strength also increased with increasing filler loading. Tensile strength of biocomposites has been observed to be comparable with neat PP up to 20% filler loading and increase in tensile modulus up to 40% was seen in biocomposites with 20% filler loading. Impact strength of biocomposites up to 20% filler loading was found to be at par with neat PP. Use of MA‐g‐PP compatibilizer in the biocomposites yielded better physico‐mechanical and thermal properties than biocomposites without compatibilizer. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42445.     

Interfacial influence on mechanical properties of polypropylene/polypropylene‐grafted silica nanocomposites

Three types of polypropylene‐grafted silica (PGS‐2 K, PGS‐8 K and PGS‐30 K) with different grafting chain lengths were prepared. After melt‐blending PGS with polypropylene (PP), we studied the PP/PGS interface properties and the influence of PP/PGS interfaces on mechanical properties of nanocomposites. The strong matrix/particle interface was observed in PP/PGS‐30 K nanocomposites with 5 wt % particle loading as evidenced by 2.5 °C increased glass transition temperature (T_g) compared with neat PP, whereas the weak matrix/particle interface was observed in PP/PGS‐2 K nanocomposites with decreased T_g. The variations in the matrix/particle interfacial strength lead to a transition in the yield stress of nanocomposites. Compared with the unfilled PP, the yield stress of the PP/PGS‐2 K nanocomposites is decreased by 0.7 MPa, and the yield stress of the PP/PGS‐30 K nanocomposites is enhanced by 1.4 MPa. In addition, benefiting from good dispersion, the PP/PGS‐masterbatch nanocomposites with a strong matrix/particle interface not only exhibit increased Young's modulus and yield stress, but also the strain at break remains in line with the unfilled PP, which is in contrast to the conventional wisdom that the gain in modulus and strength must be at the expense of the decreased break strain. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45887.     

The effect of clay type and of clay–masterbatch product in the preparation of polypropylene/clay nanocomposites

Clay containing polypropylene (PP) nanocomposites were prepared by direct melt mixing in a twin screw extruder using different types of organo‐modified montmorillonite (Cloisite 15 and Cloisite 20) and two masterbatch products, one based on pre‐exfoliated clays (Nanofil SE 3000) and another one based on clay–polyolefin resin (Nanomax‐PP). Maleic anhydride‐grafted polypropylene (PP‐g‐MA) was used as a coupling agent to improve the dispersability of organo‐modified clays. The effect of clay type and clay–masterbatch product on the clay exfoliation and nanocomposite properties was investigated. The effect of PP‐g‐MA concentration was also considered. Composite morphologies were characterized by X‐ray diffraction (XRD), field emission gun scanning electron microscopy (FEG‐SEM), and transmission electron microscopy (TEM). The degree of dispersion of organo‐modified clay increased with the PP‐g‐MA content. The thermal and mechanical properties were not affected by organo‐modified clay type, although the masterbatch products did have a significant influence on thermal and mechanical properties of nanocomposites. Intercalation/exfoliation was not achieved in the Nanofil SE 3000 composite. This masterbatch product has intercalants, whose initial decomposition temperature is lower than the processing temperature (T ～ 180°C), indicating that their stability decreased during the process. The Nanomax‐PP composite showed higher thermal and flexural properties than pure PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of maleic anhydride grafted polypropylene on the mechanical and morphological properties of chemically modified short‐pineapple‐leaf‐fiber‐reinforced polypropylene composites

With the rising cost of petroleum‐based fibers, the utilization of plant fibers in the manufacture of polymer–matrix composites is gaining importance worldwide. The scope of this study was to examine the perspective of the use of pineapple leaf fibers (PALFs) as reinforcements for polypropylene (PP). These fibers are environmentally friendly, low‐cost byproducts of pineapple cultivation and are readily available in the northeastern region of India. Here, both untreated and treated pineapple fibers were used. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as a compatibilizing agent. The polymer matrix of PP was used to prepare composite specimens with different volume fractions (5–20%) of fibers by the addition of 5% of MA‐g‐PP. These specimens were tested for their mechanical properties, and additional assessments were made via observations by scanning electron microscopy, thermogravimetric analysis, and IR spectroscopy. Increase in the impact behavior, flexural properties, and tensile moduli of the composites were noticed, and these were more appreciable in the treated fibers mixed with MA‐g‐PP. PALF in 10 vol % in PP mixed with MA‐g‐PP was the optimum and recommended composition, where the flexural properties were the maximum. The impact strength and the tensile modulus were also considerably high. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of carbon nanofibers on the fracture,mechanical, and thermal properties of PP/SEBS‐g‐MA blends

Polypropylene/maleated (styrene‐ethylene‐butadiene‐styrene) (PP/SEBS‐g‐MA) blends reinforced with 0.2–2.5 wt% carbon nanofibers (CNFs) were prepared by injection molding. The structure, thermal, mechanical, and fracture behaviors of PP/SEBS‐g‐MA blends and their nanocomposites were studied. Wide‐angle X‐ray diffraction (WAXD) results showed that the SEBS‐g‐MA and/or CNF additions do not induce a structural change of PP. Tensile measurements showed that the Young's modulus and tensile yield strength increase with the increasing filler content. Izod impact and essential work of fracture test results demonstrated that CNFs are beneficial to improve the impact strength and specific essential work of fracture of PP/SEBS‐g‐MA blends. Therefore, tough PP‐nanocomposites can be achieved by melt‐blending low fractions of CNFs and appropriate elastomer contents. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Mechanical,thermal, and morphological properties of maleic anhydride‐g‐polypropylene compatibilized and chemically modified banana‐fiber‐reinforced polypropylene composites

Composites were prepared with chemically modified banana fibers in polypropylene (PP). The effects of 40‐mm fiber loading and resin modification on the physical, mechanical, thermal, and morphological properties of the composites were evaluated with scanning electron microscopy (SEM), thermogravimetric analysis (TGA), Infrared (IR) spectroscopy, and so on. Maleic anhydride grafted polypropylene (MA‐g‐PP) compatibilizer was used to improve the fiber‐matrix adhesion. SEM studies carried out on fractured specimens indicated poor dispersion in the unmodified fiber composites and improved adhesion and uniform dispersion in the treated composites. A fiber loading of 15 vol % in the treated composites was optimum, with maximum mechanical properties and thermal stability evident. The composite with 5% MA‐g‐PP concentration at a 15% fiber volume showed an 80% increase in impact strength, a 48% increase in flexural strength, a 125% increase in flexural modulus, a 33% increase in tensile strength, and an 82% increase in tensile modulus, whereas the heat deflection temperature increased by 18°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of interfacial adhesion on properties of polypropylene/Wollastonite composites

Wollastonite reinforced polypropylene (PP/CaSiO₃) composites were prepared by melt extrusion. A silane coupling agent and a maleic anhydride grafted PP (PP‐g‐MA) were used to increase the interfacial adhesion between the filler and the matrix. The increased adhesion observed by scanning electron microscopy (SEM) resulted in improved mechanical properties. A model was applied to describe the relationship between the interfacial adhesion and tensile properties of PP/CaSiO₃ composites. There is stronger interfacial adhesion between silane‐treated CaSiO₃ and polymer matrix containing PP‐g‐MA as a modifier. Results of dynamic mechanical thermal analysis (DMTA) showed that stronger interfacial adhesion led to higher storage modulus. The influence of CaSiO₃ particles on the crystallization of PP was studied by using differential scanning calorimetry (DSC). The introduction of CaSiO₃ particles does not affect the crystallization temperature and crystallinity of PP matrix significantly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of polymer matrix/montmorillonite compatibility on morphology and melt rheology of polypropylene nanocomposites

In this study, Ca²⁺‐montmorillonite (Ca²⁺‐MMT) and organo‐montmorillonite (OMMT) were modified by three compatibilizers with different degrees of polarity [poly(ethylene glycol) (PEG), alkyl‐PEG, and polypropylene (PP)‐g‐PEG]. PP/MMT nanocomposites were prepared by melt blending and characterized using X‐ray diffraction and transmission electron microscopy. The results showed the degree of dispersion of OMMT in the PP/PP‐g‐PEG/OMMT (PMOM) nanocomposite was considerably higher than those in the PP/PEG/OMMT and PP/alkyl‐PEG/OMMT nanocomposites, which indicated that the dispersion was relative to the compatibility between modified OMMT and PP matrix. Linear viscoelasticity of PP/MMT nanocomposites in melt states was investigated by small amplitude dynamic rheology measurements. With the addition of the modified MMT, the shear viscosities and storage modulus of all the PP/MMT nanocomposites decreased. It can be attributed to the plasticization effect of PEG segments in the three modifiers. This rheological behavior was different from most surfactant modified MMT nanocomposites which typically showed an increase in dynamic modulus and viscosity relative to the polymer matrix. The unusual rheological observations were explained in terms of the compatibility between the polymer matrix and MMT. In addition, the mechanical properties of PP/MMT nanocomposites were improved. A simultaneous increase in the tensile strength and toughness was observed in PP/PMOM nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013