A novel balanced wideband power divider based on microstrip‐slot transitions

A novel design of a balanced wideband power divider (PD) with enhanced common‐mode (CM) suppression is proposed. The top and bottom layers of the structure contain tapered microstrip line. Those microstrip lines are coupled via slotline in the ground plane, which is located at the middle layer. With appropriate placement of the slotline, the coupling between the slotline mode and the differential‐mode (DM) signals can be maximized, while that between the slotline mode and the CM signals can be minimized. Simulated and measured results show that the proposed PD has equal power division, low insertion loss, and good return loss. In the measurement, the fractional bandwidth of the measured ?10 dB (DM) return loss is about 101% (1.82–5.35 GHz), the insertion loss for the DM signals is less than 5 dB, the suppression of the CM signals is higher than 45 dB, and the DM isolation is better than 10 dB over the fractional bandwidth. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:437–442, 2014.     

Dual‐band balanced coupler with wideband common‐mode suppression

A novel compact dual‐band balanced coupler with differential‐mode power division, broadband common‐mode, and common‐to‐differential‐mode conversion suppression is proposed. In these double‐functionality balanced‐coupler architectures, double‐sided parallel‐strip line 180° phase inverters are used to realize the broadband common‐mode rejection. Moreover, the frequency is tunable by changing the characteristic impedance of the transmission line. For practical verification, a balanced couplers (ε_r = 2.65, h = 0.5 mm, tan(δ_D) = 0.003) operation at 0.9/1.8 GHz is constructed in microstrip technology and tested.     

Compact dual‐band single‐ended‐to‐balanced power dividers with open/short‐ended stubs

In this article, two novel topologies of compact‐size dual‐band single‐ended‐to‐balanced power dividers that are loaded with open‐ and short‐ended stubs are presented. Quarter‐wavelength open‐ended stubs and half‐wavelength short‐ended stubs are respectively exploited in the proposed dual‐band power‐divider configurations to incorporate the dual‐band functionality into them for flexibly‐adjustable dual‐frequency‐ratio specifications. Each engineered five‐port power‐divider circuit features high in‐band input/output power‐matching levels, high in‐band power‐isolation levels between the two differential‐mode outputs, and high common‐mode‐rejection levels in a broad spectral range. Two microstrip prototypes designed at 0.9/1.8 GHz (GSM bands) and 1.57/2.45 GHz (GPS and WLAN bands) are constructed and characterized for experimental‐demonstration purposes.     

Balanced power dividers with improved bandwidth using folded lines

Two novel wideband balanced‐to‐unbalanced power dividers based on transmission lines and coupled lines are proposed in this article. Multifunction can be realized without cascading single devices with common mode suppression. The desired power divider configurations can be obtained using the even/odd‐mode characteristic impedance of the coupled lines and characteristic impedance of the transmission lines. A resistor in the middle of two single‐ended ports is used to realize isolation between output ports. Two prototypes of wideband balanced‐to‐unbalanced power dividers operating at 2.3 GHz with differential‐mode bandwidths of 79.6 and 134.1% are designed and fabricated. The theoretical and measured results are in good agreement and show good in‐band performances.     

A broadband out‐of‐phase gysel power divider based on a dual‐band circuit with a single fixed isolation resistor

Based on the double‐sided parallel‐strip lines with an inserted conductor as a virtual ground, a high power divider with dual‐band/broadband response and frequency‐independent 180° phase difference between the output ports is implemented in this paper. The circuit topology employs a single commercially available external isolation resistor as well as moderate line impedances (15–100 ohm), making it suitable for high‐power applications. Precise closed‐form design equations on the basis of even‐ and odd‐mode analysis are derived. In addition to the wide range of frequency band ratios from 1 to 2.65, broadband response is also obtained by selecting the proper value of frequency band ratios. To substantiate the design equations and theory, a circuit with 2:1 frequency ratio and 84.5% bandwidth referring to 16 dB isolation and 12 dB return loss values is developed. To the authors' knowledge, this is the widest bandwidth reported for out‐of‐phase high power dividers. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2016.     

Multiband multiple‐input multiple‐output antenna with high isolation for future 5G smartphone applications

A multiband high‐isolation multiple‐input multiple‐output (MIMO) antenna using balanced mode and coupled neutralization line (NL) is presented in this article. The balanced modes of dipole and loop antennas, which leads to good isolation intrinsically are used for the 8 × 8 MIMO in the LTE bands 42 (3400‐3600 MHz)/Chinese 5G band (3300‐3400 and 3400‐3600 MHz). The unbalanced mode of loop antennas, which optimized by decoupling structure are designed for the 4 × 4 MIMO in the LTE band 40 (2300‐2400 MHz). Therefore, the eight‐antenna array is formed by four dipole elements and four loop elements. The simulated and measured results show that the proposed antenna can cover 2300 to 2400 and 3300 to 3600 MHz, with reflection coefficient better than ?6 dB and isolation higher than 15 dB. Good radiation performance and low envelope correlation coefficient can also be obtained. Specific absorption rate of user's hand is also discussed in this article.     

Balanced circularly polarized square loop antenna under even‐mode resonance

Design approach to a novel balanced, circularly polarized (CP) square loop antenna under even‐mode resonance is proposed in this paper. The loop antenna is diagonally fed by a fork‐like dipole launcher. By matching the respective natural boundary condition of the loop radiator and the dipole launcher, the resonant even‐mode with inherent CP radiation characteristic can be sufficiently excited. Both the bi‐ and uni‐directional cases are designed and investigated. A bi‐directional CP loop antenna with a 3‐dB ratio axial ratio (AR) bandwidth of 6.6% is designed at first. A uni‐directional antenna having a planar metallic reflector is further designed. The uni‐directional loop antenna exhibits excellent uni‐directional CP performance with a high front‐to‐back ratio of 40dB and a 3‐dB AR bandwidth of 7.6% in both theory and experiment.     

A BTB UWB power divider with arbitrary power‐dividing ratio based on three‐slotline structure

In this article, a balanced‐to‐balanced (BTB) ultra‐wide band (UWB) power divider (PD) is proposed, which can realize arbitrary power‐dividing ratio (PDR) with improved transmission bandwidth flatness. The proposed PD is primarily based on microstrip/slotline (MS) transition structures and parallel‐coupled three‐slotline structure. U‐type microstrip feed lines integrated with stepped‐impedance slotline resonators are adopted at the input and output ports, which make the differential‐mode (DM) responses independent of the common‐mode (CM) ones. Meanwhile, superior DM transmission and CM suppression are achieved intrinsically, thereby simplifying the design procedure significantly. By changing the distances between the coupled three slotlines, the PDR between the output ports is controllable. In order to verify the feasibility of the proposed design method, several prototype circuits of the proposed PDs with different PDRs are simulated and a prototype circuit with the 2:1 PDR is fabricated and measured. A good agreement between the simulation and measurement results is observed.     

Generalized high‐isolation n‐way Gysel power divider with arbitrary power ratio and different real terminated impedances

An exact closed‐form design approach for a generalized high‐power n‐way Gysel power divider is proposed. The power divider could be designed to achieve an arbitrary power ratio with the flexible multiway application, arbitrary real terminated impedance, excellent isolation, and easy fabrication through both planar and three‐dimensional structures. Moreover, this improved power divider could maintain high power processing capacity through the coaxial cavity transmission line and grounding resistances. The exact analytical solutions related to ideal port matching and high isolation are obtained based on the circuit and transmission‐line theory. To verify the proposed approach, a compact 3‐way coaxial power divider with a pre‐designed power ratio of 1:1.5:2 and four different real terminated impedances of 50, 55, 60, and 65 Ω is designed and fabricated. Excellent agreement is achieved between the simulated and measured results. Measurements from 4.7 to 5.7 GHz show that the return losses of all input and output ports are better than 15 dB. The maximum insertion loss is 0.5 dB, and the phase imbalance is approximately less than 6.1°. In addition, the isolation between any two output ports is better than 23 dB from 4.5 to 6 GHz. Meanwhile, the power handling capability can reach the maximum power of the commercial 50 Ω SMA connectors (2.098 kW).     

A new dual‐band single‐ended‐to‐balanced filtering power divider

This article proposes a new dual‐band single‐ended‐to‐balanced (SETB) filtering power divider (FPD), which shows the excellent characteristics of wideband common‐mode (CM) suppression and good selectivity. By employing the structure of double‐sided parallel‐strip line with a mid‐inserted conductor and a T‐shaped defected ground structure etched in the mid‐inserted conductor, out‐of‐phase behavior and high CM suppression can be achieved successfully. Besides, to realize dual‐wideband filtering performance and high selectivity, two pairs of step impedance stubs (SIS) loaded quarter‐wavelength central line‐terminal‐shorted three parallel‐coupled microstrip lines structure are adopted. Meanwhile, two pairs of resistors are introduced so as to realize excellent isolation. To verify effectiveness of the design method, a prototype of dual‐band SETB FPD which operates at 3.2 and 4.9 GHz is designed, fabricated, and tested. Final results exhibit that the new dual‐band SETB FPD possess high selective dual‐band differential mode response, wideband CM suppression, and excellent isolation between the balanced output ports.     

Compact wideband MIMO mobile‐antenna system design using mode‐based decoupling techniques

This work focuses on designing small mobile antennas and their multiple‐input multiple‐output (MIMO) applications. In this study, it was investigated that small mobile antennas can obtain high radiation performance only when a tight coupling with the ground plane is generated through ground‐mode tuning (GMT) of the ground plane. Furthermore, a novel mode‐based decoupling concept is presented for their MIMO applications, based on a four‐port network and by considering the ground‐mode effect. Consequently, the proposed mode‐based decouplers can effectively sustain high radiation performance and improve the isolation while providing low correlation by generating diagonally directed radiation patterns. In the proposed MIMO system, both GMT structures and mode‐based decouplers are implemented utilizing the metal rims around the ground plane, thereby occupying very compact clearance, and the measured MIMO antennas fully covered 0.69 to 1 GHz band with high isolation up to 20 dB and low envelope correlation coefficient (ECC) value below 0.5, sufficiently applicable in mobile devices.     

A 1‐to‐n way single‐ended‐to‐balanced substrate integrated waveguide filtering power splitter

An approach to 1‐to‐n (n = 3, 4…) way single‐ended‐to‐balanced filtering power splitter (SETBFPS) is proposed. The properly placed balanced ports with 0.5λ_g (λ_g is the substrate integrated waveguide [SIW] guided wavelength at f₀) space make the TE32nd 103 and TE32nd 105 modes of n 32nd‐mode SIW multimode resonators form differential‐mode (DM) passband of the SETBFPS. Compared with the state‐of‐art single‐ended‐to‐balanced power splitters, the proposed approach has all the functions of 1‐to‐n way, filtering, and common‐mode (CM) suppression. A 1‐to‐3 way prototype is exemplified at 3.5 GHz with the minimum insertion loss (IL) of 0.09 dB, a fractional bandwidth (FBW) for a 15‐dB return loss of 35%, and a FBW for 15‐dB CM suppression of 52%. Low IL and wide bandwidth can be observed.     

Filtering balanced‐to‐single‐ended power dividing network

In this article, the filtering balanced‐to‐single‐ended power dividing networks are proposed. Except the fundamental functions of differential‐mode transmission, common‐mode suppression, and out‐of‐phase single‐ended output ports with isolation, the proposed designs show the advantages of wide controllable range of differential‐mode bandwidth, multiple transmission zeros (TZs), and wide bandwidth for high out‐of‐band suppression. The frequencies of TZs, bandwidth, isolation, and common‐mode suppression can be controlled by the parameters. For demonstration, three prototypes (Deigns I, II, and III) with two, four, or six TZs are implemented. The measured results show that design I (II and III) has an insertion loss of 0.38 dB (0.7 dB and 0.8 dB), an operating bandwidth of 12.5% (7.5% and 6.9%), and a bandwidth for 30‐dB out‐of‐band suppression of 0.06f₀ (0.09f₀ and 0.14f₀). The isolation and common‐mode suppression inside the passbands of the three prototypes are all larger than 17 and 38 dB, respectively.     

Dual‐band Gysel power dividers with large frequency ratio and unequal power division

In this article, a dual‐band Gysel power divider is proposed based on the topology of finite‐ground microstrip line. The general design method for the large frequency ratio and unequal power division is derived and the detailed design rules are provided. It is shown that the frequency ratio can be achieved from 1 to 10, and the power division ratio of each frequency band can be separately determined. Moreover, the phase differences at two operating bands could be designed to be either in‐phase or out‐of‐phase. Finally, two prototypes are designed, implemented, and experimented to validate this proposal. The measured results of the first design show the frequency ratio of 4 with power division ratios of 2:1 in both passband, while the second example is designed with the frequency ratio of 10 with power division ratios of 2:1 and 1:1 in the first and second passband, respectively. Both results show a good agreement between the simulated and measured results.     

Dual‐passband bandpass‐filtering power divider using half‐mode substrate integrated waveguide resonator with high frequency selectivity

In this paper, a half‐mode substrate integrated waveguide (HMSIW) power divider with bandpass response and good frequency selectivity is proposed. The proposed power divider includes input/output microstrip lines, four HMSIW resonators, cross‐coupling circuits, and an isolation resistor. The dual‐band bandpass‐filtering response is obtained by using the dual‐mode slotted HMSIW. To get good frequency selectivity, the input/output cross‐coupling circuits have been used, and several transmission zeros can be observed. A dual‐band filtering‐response HMSIW power divider is designed, fabricated and measured. The total size of the fabricated power divider is 0.58λg × 0.45λg. The measured results show a reasonable agreement with the simulated ones. The measured central operating frequencies of the dual‐band HMSIW power divider are at 2.43 and 3.50 GHz, respectively. The measured 3‐dB fractional bandwidth is about 13.3% and 6.3% in the two passbands, and the measured output isolation is about 20 dB.     

Design scheme for broadband Doherty power amplifier using broadband load combiner

This article proposes a design strategy for broadband Doherty power amplifier (PA) using broadband load combiner. The bandwidth of the Doherty PA based on the proposed combiner using packaged transistor is about 2.5 times the bandwidth of conventional Doherty PA using a quarter‐wave transformer. An easy to implement analytical design methodology has been presented for the proposed load‐combiner while describing the bandwidth enhancement strategy. The design methodology is validated with the design of a broadband Doherty PA based on CREE 10 W packaged GaN high electron mobility transistor devices using the proposed load combiner. Measurement results show more than 45% drain efficiency at 6 dB output power back‐off (OPBO) over 400 MHz frequency range, centred around 1.95 GHz. The peak drain efficiency at saturation is better than 60% over this band of operation. At 6 dB OPBO, the maximum improvement of 18.5% in drain efficiency is achieved as compared to the balanced mode PA. Measurement with single carrier wideband code division multiple access modulated signal shows the average drain efficiency of more than 44% at 36.6 dBm average output power at center frequency of operation. The adjacent channel power ratio is better than ?45 dBc after applying digital predistortion. The circuit is realized with microstrip technology, which can be easily fabricated using conventional printed circuit processes. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:655–674, 2015.     

A bandwidth‐agile balanced filtering power divider

In this article, a balanced filtering power divider (FPD) that allows for operational agility of the bandwidth (BW) is presented. The differential‐mode power dividing and high common‐mode (CM) suppression can be realized by microstrip‐to‐slotline transition. Two slotline open stubs with different lengths are added in shunt to the main slotline for the transition, which can not only introduce transmission poles for extending and controlling transition BW, but also generate two extra transmission zeros (TZs) near to the passband edges, featuring good filtering response. The two transmission poles can be independently tunable by loading varactors to the open ends of slotline stubs and two TZs will be changed accordingly so that the filtering passband BW is electrically tunable. To verify the theoretical prediction, a prototype of tunable balanced FPD is fabricated and measured. The measured results show that the 3‐dB fractional bandwidth (FBW) of the passband varies from 5.6% to 12.6%, meaning more than a double tuning range for the FBW, and the CM suppression is better than 40 dB across the frequency band of interest.     

A compact balun‐diplexer using interdigital line resonators

A novel compact balun‐diplexer applying new interdigital line resonators (ILRs) is presented in this article. It is found that the proposed ILR can not only reduce circuit size and but also realize high common mode rejection in differential mode operation frequency. By properly converting the symmetric four‐port balanced bandpass filter (BPF) to a three‐port device, a balun BPF with high selectivity and compact size are accomplished using ILRs. Then, the balun‐diplexer can be realized by combining two well‐designed balun filters with two 50 Ω transmission lines. The demonstrated balun‐diplexer with operation at 1.8 and 2.45 GHz have been designed, fabricated, and measured. Excellent performances have been observed. Specifically, 0.4 dB in‐band amplitude error, 1.8 in‐band phase error, more than 50 dB selectivity and 45 dB isolation are obtained. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:485–489, 2015.     

Equal and unequal quad‐band Gysel power dividers

This article presents for the first time a quad‐band Gysel power divider capable of achieving equal and unequal power division at four arbitrary frequencies. The structure of the proposed divider is similar to its single‐band counterpart but loaded with quad‐band reactive networks. The design procedure and theoretical analysis of the proposed divider are presented. A quad‐band Gysel power divider with equal division and another with 2:1 unequal division are designed at the operational frequencies of 0.85, 1.6, 2.4, and 3 GHz. Simulation and measurement results of the two dividers are presented, and good performance is observed at each band. For both designs, the realized power division ratios are within 1 dB from their ideal values, whereas the matching and isolation levels are below ?10 dB at the four bands.     

An unbalanced‐to‐balanced diplexer based on substrate integrated waveguide cavity

A novel unbalanced‐to‐balanced diplexer based on a dual‐mode substrate integrated waveguide (SIW) cavity is proposed and implemented. The diplexer is realized using one dual‐mode cavity and two single‐mode cavities. By properly choosing, feeding and coupling the cavity operating at the TE₁₀₂ or TE₂₀₁ mode, so as to not only provide capabilities to realize the desired unbalanced‐to‐balanced transmission within both Rx and Tx channels but also realize good differential‐mode channel‐to‐channel isolation. To the author's knowledge, we present for the first time an unbalanced‐to‐balanced type diplexer based on the application of SIW. The proposed diplexer was successfully designed, simulated, and fabricated. Good agreement can be observed between simulated and measured performances in our letter. The measured in‐band common‐mode rejection is better than 33 dB for both channels. A minimum differential‐mode isolation of about 50 dB across the Rx band and about 40 dB across the Tx band is also observed in the measurement. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:173–177, 2015.