共查询到17条相似文献,搜索用时 125 毫秒
1.
本文在MATLAB环境下建立了二级倒立摆的半物理实时仿真模型,并应用线性二次型最优控制策略.设计了一个二级倒立摆LQR控制器。在实验中,运行该半实物仿真模型,成功的使倒立摆稳定地平衡在“倒立”状态。 相似文献
2.
3.
4.
5.
二级倒立摆的二次型最优控制研究 总被引:8,自引:2,他引:8
倒立摆系统以其自身的不稳定性而难以控制,也因此成为自动控制实验中验证控制策略优劣的极好的实验装置。针对二级倒立摆系统的平衡控制问题,对其进行数学建模,应用二次型最优控制理论设计了控制器。仿真结果表明,二次型最优控制对于典型非线性自不稳定系统有着很好的控制能力。 相似文献
6.
为了实现对单级倒立摆系统的控制,提出了一种基于LQG(线性二次型高斯控制)的倒立摆系统控制方法.利用LQR(线性二次最优)构建系态反馈矩阵,再结合Kalman滤波器,综合得到了LQG控制器,并对该控制器的参数进行了优化设计.通过MATLAB仿真,验证了采用的控制算法能够有效地对单级倒立摆系统进行控制,系统超调量较小,并具有一定的鲁棒性. 相似文献
7.
8.
针对倒立摆系统的不稳定性,对最优控制理论在倒立摆控制系统中的应用进行了分析,设计LQR控制器,并在倒立摆实验装置上进行了实验。实验结果表明设计的控制器是有效的,对倒立摆系统的平衡稳定控制效果好,提高了系统的抗干扰能力。 相似文献
9.
针对二级直线倒立摆系统,采用拉格朗日方程法建立其理论模型,分别使用线性二次最优控制(Linear Quadratic Regulator,LQR)及基于趋近律的滑模控制(Sliding Mode Control,SMC)算法来实现干扰存在情况下倒立摆的平衡控制。对于LQR算法,研究了矩阵[Q]和矩阵[R]与反馈控制矩阵[K]的定性关系,并经过反复多次实验,不断试凑,得到一组良好的控制参数,实现了倒立摆的稳定控制。SMC算法采用基于指数趋近律的控制方法进行了滑模变结构控制器的设计,并利用边界层法来进一步削弱抖振。最后通过仿真及实验,实现了倒立摆的实物平衡控制。 相似文献
10.
小车倒立摆系统是一个典型的多变量、非线性、强耦合和快速运动的自然不稳定系统,其控制问题被公认为控制理论的一个典型问题,是控制理论研究的典型实验平台.旋转二级倒立摆是一种新型的倒立摆装置,与同级的直线轨道倒立摆相比,结构简单紧凑,但模型更复杂和不稳定,对控制算法提出更高的要求,增加了控制难度.该文基于动力学理论分析旋转二级倒立摆系统的结构,建立了旋转二级倒立摆系统的数学模型状态空间方程,分析了系统的稳定性和可控性.采用二次型最优控制策略对旋转二级倒立摆系统进行控制系统设计,并借助Matlab平台进行了仿真实验.实验结果证明了其控制有效性,该控制结果与其它控制方法相比,有较优的稳态特性和快速性,系统处在较大的非平衡初始状态,旋转二级摆杆也能稳定地控制在倒立平衡位置附近.因此可以进一步扩展到多级旋转倒立摆的控制,对于实现其它不稳定系统的控制,也有着一定的借鉴价值. 相似文献
11.
12.
Linear quadratic regulator(LQR) and proportional-integral-derivative(PID) control methods, which are generally used for control of linear dynamical systems, are used in this paper to control the nonlinear dynamical system. LQR is one of the optimal control techniques, which takes into account the states of the dynamical system and control input to make the optimal control decisions.The nonlinear system states are fed to LQR which is designed using a linear state-space model. This is simple as well as robust. The inverted pendulum, a highly nonlinear unstable system, is used as a benchmark for implementing the control methods. Here the control objective is to control the system such that the cart reaches a desired position and the inverted pendulum stabilizes in the upright position. In this paper, the modeling and simulation for optimal control design of nonlinear inverted pendulum-cart dynamic system using PID controller and LQR have been presented for both cases of without and with disturbance input. The Matlab-Simulink models have been developed for simulation and performance analysis of the control schemes. The simulation results justify the comparative advantage of LQR control method. 相似文献
13.
为解决LQ控制多变量系统时权矩阵参数难以确定的问题,在引入一种与系统动态性能密切相关的性能指标基础上,提出了混沌全局粗搜索和局部细搜索相结合的优化LQ控制器,并且进行了二级倒立摆的实时控制.最后的实验证实了,该方法既是线性二次型泛函意义下的最优,又能解决具有快速、强非线性、绝对不稳定系统的控制问题. 相似文献
14.
15.
Swing-up and LQR stabilization of a rotary inverted pendulum 总被引:2,自引:0,他引:2
In this article, we consider the swing-up and linear quadratic regulator (LQR) stabilization of a rotary inverted pendulum.
A DC motor rotates a rigid arm. At the end of the rigid arm is a joint with a pendulum suspended from it. Two encoders check
the degree of the rigid arm and the pendulum every 0.5 ms. This article describes a modified bang-bang control which swings
the pendulum up safely and fast. In order to solve the stabilization problem, we used a linear quadratic regulator. When the
user gives a large disturbance to the pendulum so that it loses its position, it quickly recovers to the upright position.
Experimental results showed that the proposed bang-bang and LQR controllers can stabilize a rotary inverted pendulum system
within 3.0 s from any starting point. The system also showed robustness to a large disturbance. 相似文献
16.
17.
直线倒立摆作为一种典型的非线性系统,是一种经典的控制理论研究对象.本文将状态依赖的Riccati方程(SDRE)方法与极点配置方法结合,进行倒立摆非线性控制的研究.该方法与SDRE相比,不再需要实时计算Riccati方程,同时克服了线性最优控制(LQR),线性鲁棒(H∞)控制等控制域不足的问题,可实现几乎任意初始摆角的稳定控制,而且在稳定点附近保持与某期望的线性控制方法完全相同.实验表明了该控制方法的有效性和对扰动的鲁棒性.最后讨论了SDRE进行一致性起摆控制的硬件可行性,以及系统对于传感器零点漂移的鲁棒性. 相似文献