Microwave-polyol controlled synthesis and magnetic properties of monodisperse CoxNi1−xFe2O4/MWCNT nanocomposites

Monodisperse Co_xNi_1−xFe₂O₄ nanoparticles (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, and 1) with controllable composition attached on the multi-walled carbon nanotubes (MWCNTs) were prepared by microwave-polyol method. The composition of Co_xNi_1−xFe₂O₄ nanoparticles can be controlled through adjusting the atomic ratios of cobalt and nickel nitrate in the mixed solution. The influence of the microwave power and microwave irradiation time on the monodispersion of nanoparticles was also investigated. The results show quasi-spherical Co_xNi_1−xFe₂O₄ nanoparticles with the face-centered cubic structure and average crystallite size (6 nm) are uniformly dispersed on MWCNTs. The saturation magnetization of Co_xNi_1−xFe₂O₄/MWCNT nanocomposites increases gradually from 12.90 to 20.03 emu/g with increasing Co²⁺ concentration. The coercivity is almost zero at room temperature, which indicates the superparamagnetic behavior.     

High T2-relaxation and biocompatible magnetic nanofluids with poly(amino acid) coating

A facile one-pot method has been developed to prepare poly(amino acid) functionalized, water-stable, biocompatible, and superparamagnetic iron oxide nanoparticles (NPs) with small diameters of ∼10 nm. The obtained biocompatible magnetic nanoparticles capped with polyaspartic acid (PASP) exhibit a relatively high saturation magnetization (57.1 emu/g) and a much strong magnetic resonance (MR) T₂ relaxation effect with the transverse relaxivity coefficient (r₂) as high as 302.6 s⁻¹ mM⁻¹. Interestingly, the as-prepared Fe₃O₄@PASP NPs are highly stable in aqueous solution and demonstrate the property of magnetic nanofluids. The high T₂ effect, good water-stability, superparamagnetization, biocompatibility and bioconjugatability render the as-synthesized Fe₃O₄@PASP NPs great desirable for bioapplications such as magnetic resonance imaging (MRI), bioseparation, targeted drug delivery, and so on.     

Effects of poly(oxyethylene)-block structure in polyetheramines on the modified carbon nanotube/poly(lactic acid) composites

The hybrids of multi-walled carbon nanotube and poly(lactic acid) (MWCNT/PLA) were prepared by a melt-blending method. In order to enhance the compatibility between the PLA and MWCNTs, the surface of the MWCNTs was covalently modified by Jeffamine® polyetheramines by functionalizing MWCNTs with carboxylic groups. Different molecular weights and hydrophilicity of the polyethermaines were grafted onto MWCNTs with the assistance of a dehydrating agent. The results showed that low-molecular-weight Jeffamine® polyetheramine modified MWCNTs can effectively improve the thermal properties of PLA composites. On the other hand, high-molecular-weight and poly(oxyethylene)-segmented polyetheramine could render the modified MWCNTs of well dispersion in PLA, and consequently affecting the improvements of mechanical properties and conductivity of composite materials. With the addition of 3.0 wt% MWCNTs, the increment of E′ of the composite at 40 °C was 79%. For conductivity, the surface resistivity decreased from 1.27 × 10¹² Ω/sq for neat PLA to 8.30 × 10⁻³ Ω/sq for the composites.     

Preparation of aligned Fe3O4@Ag-nanowire/poly(vinyl alcohol) nanocomposite films via a low magnetic field

Aligned Fe₃O₄@Ag-nanowire (Ag-NW)/poly(vinyl alcohol) (PVA) nanocomposite films are prepared via a magnetic field-assisted method under a low magnetic field (B < 0.1 T) induction. The effects of the mass ratio (MR) of Fe₃O₄ to Ag-NWs and the Ag-NW content are systematically studied on the composite electrical conductivity (EC). The preferential alignment of Ag-NWs brings about a significant increase in the EC of the oriented composite in the parallel direction along the magnetic field. The optimal MR is determined to be equal to 0.15 at which the random composite has a good EC meanwhile the oriented composite shows a good response to the applied magnetic field. The oriented composite with the 20 wt% Ag-NWs shows a high EC anisotropy of ca. 6.6 and a very high EC of 4500 S/cm via the external magnetic field. In addition, the introduction of Ag-NWs leads to an obvious improvement in the thermal stability of PVA composites.     

Graphene-enhanced microwave absorption properties of Fe3O4/SiO2 nanorods

Fe₃O₄/SiO₂/graphene composite composed of Fe₃O₄/SiO₂ core–shell nanorods and graphene nanosheets were synthesized by a facile wet chemical method. Structure and morphology studies reveal that the Fe₃O₄/SiO₂ nanorods with porous structure and large aspect ratio are densely wrapped by the graphene nanosheets. By changing the graphene content, the electromagnetic properties of the Fe₃O₄/SiO₂/graphene composite can be well tuned. When the weight ratio of Fe₃O₄/SiO₂ to graphene reaches an appropriate value, excellent microwave absorption performance is achieved due to the large electromagnetic losses and good impedance matching. The Fe₃O₄/SiO₂/graphene composite with graphene content of 5 wt.% shows the minimum reflection loss of −27.1 dB at 12.2 GHz when the coating layer thickness is only 1.5 mm.     

Enhanced thermal conductivity and dielectric properties of Al/β-SiCw/PVDF composites

Polymeric composites with high thermal conductivity, high dielectric permittivity but low dissipation factor have wide important applications in electronic and electrical industry. In this study, three phases composites consisting of poly(vinylidene fluoride) (PVDF), Al nanoparticles and β-silicon carbide whiskers (β-SiC_w) were prepared. The thermal conductivity, morphological and dielectric properties of the composites were investigated. The results indicate that the addition of 12 vol% β-SiC_w not only improves the thermal conductivity of Al/PVDF from 1.57 to 2.1 W/m K, but also remarkably increases the dielectric constant from 46 to 330 at 100 Hz, whereas the dielectric loss of the composites still remain at relatively low levels similar to that of Al/PVDF at a wider frequency range from 10⁻¹ Hz to 10⁷ Hz. With further increasing the β-SiC_w loading to 20 vol%, the thermal conductivity and dielectric constant of the composites continue to increase, whereas both the dielectric loss and conductivity also rise rapidly.     

High-temperature dielectric and electromagnetic interference shielding properties of SiCf/SiC composites using Ti3SiC2 as inert filler

Ti₃SiC₂ filler has been introduced into SiC_f/SiC composites by precursor infiltration and pyrolysis (PIP) process to optimize the dielectric properties for electromagnetic interference (EMI) shielding applications in the temperatures of 25–600 °C at 8.2–12.4 GHz. Results indicate that the flexural strength of SiC_f/SiC composites is improved from 217 MPa to 295 MPa after incorporating the filler. Both the complex permittivity and tan δ of the composites show obvious temperature-dependent behavior and increase with the increasing temperatures. The absorption, reflection and total shielding effectiveness of the composites with Ti₃SiC₂ filler are enhanced from 13 dB, 7 dB and 20 dB to 24 dB, 21 dB and 45 dB respectively with the temperatures increase from 25 °C to 600 °C. The mechanisms for the corresponding enhancements are also proposed. The superior absorption shielding effectiveness is the dominant EMI shielding mechanism. The optimized EMI shielding properties suggest their potentials for the future shielding applications at temperatures from 25 °C to 600 °C.     

Soybean oil-based thermosets with N-vinyl-2-pyrrolidone as crosslinking agent for hemp fiber composites

Soybean oil-based thermosets from acrylated epoxidized soybean oil (AESO) with a highly reactive vinyl monomer, N-vinyl-2-pyrrolidone (NVP), as crosslinking agent to replace styrene (St) were formulated for the fabrication of hemp fiber composites. The theoretical miscibility of NVP–AESO and St–AESO systems were discussed based on the group contribution method. The AESO resin with 30 wt% NVP exhibited a slightly higher viscosity than the counterpart with St, while the maximum curing temperature of the former was considerably lower than that of the latter. The composites from 20 wt% NVP resin gained comparable mechanical properties and higher glass transition temperature (T_g) to the composites with 30 wt% St. Further increase in NVP usage to 40 wt% resulted in the composites with higher tensile strength, tensile modulus, flexural strength, flexural modulus, storage modulus, and T_g of 29.6%, 22.4%, 22.5%, 20.6%, 21.6%, and 47.2%, respectively, when compared to those of the St-based composites.     

Effect of aspect ratio on thermal conductivity of high density polyethylene/multi-walled carbon nanotubes nanocomposites

This study aims to investigate experimentally the effects of aspect ratio (length/diameter ratio) and concentration of multiwalled carbon nanotubes (MWCNTs) on thermal properties of high density polyethylene (HDPE) based composites. The aspect ratios of two types of MWCNT fillers are in the range of 200–400 and 500–3000. Composite samples were prepared by melt mixing up to weight fraction of 19% filler content, followed by a compression molding. Measurements of density, specific heat and thermal diffusivity (by modulated photothermal radiometry, PTR) were performed and effective thermal conductivities k_e of nanocomposites were calculated using these values. The results show that the composites containing MWCNTs with higher aspect ratio have higher thermal conductivities than the ones with lower aspect ratio. In terms of conductivity enhancement k_e/k_m − 1, the results indicate that MWCNTs with higher aspect ratio provide three to fourfold larger enhancement than the ones with lower aspect ratio, at low filler concentrations.     

Preparation of Fe3O4–chitosan nanoparticles used for hyperthermia

The Fe₃O₄–chitosan nanoparticles with core-shell structure have been prepared by crosslinking method. Oleic acid modified Fe₃O₄ nanoparticles were firstly prepared by co-precipitation then chitosan was added to coat on the surface of the Fe₃O₄ nanoparticles by physical absorption. The Fe₃O₄–chitosan nanoparticles were obtained by crosslinking the amino groups on the chitosan using glutaraldehyde. Transmission electron microscopy showed that the Fe₃O₄–chitosan nanoparticles were quasi-spherical with a mean diameter of 10.5 nm. X-ray diffraction pattern and X-ray photoelectron spectra indicated that the magnetic nanoparticles were pure Fe₃O₄ with a cubic inverse spinel structure. The modification using chitosan did not result in a phase change. The binding of chitosan to the Fe₃O₄ nanoparticles was also demonstrated by the measurement of fourier transform infrared spectra and thermogravimetric analysis. Magnetic measurement revealed that the saturation magnetization of the composite nanoparticles was 30.7 emu/g and the nanoparticles were superparamagnetic at room temperature. Furthermore, the inductive heating property of the composite nanoparticles in an alternating current magnetic field was investigated and the results indicated that the heating effect was significant. The Fe₃O₄–chitosan nanoparticles prepared have great potential in hyperthermia.     

The influence of nano/micro hybrid structure on the mechanical and self-sensing properties of carbon nanotube-microparticle reinforced epoxy matrix composite

Nano/micrometer hybrids are prepared by chemical vapor deposition growth of carbon nanotubes (CNTs) on SiC, Al₂O₃ and graphene nanoplatelet (GNP). The mechanical and self-sensing behaviors of the hybrids reinforced epoxy composites are found to be highly dependent on CNT aspect ratio (AR), organization and substrates. The CNT–GNP hybrids exhibit the most significant reinforcing effectiveness, among the three hybrids with AR1200. During tensile loading, the in situ electrical resistance of the CNT–GNP/epoxy and the CNT–SiC/epoxy composites gradually increases to a maximum value and then decreases, which is remarkably different from the monotonic increase in the CNT–Al₂O₃/epoxy composites. However, the CNT–Al₂O₃ with increased AR ⩾ 2000 endows the similar resistance change as the other two hybrids. Besides, when AR < 3200, the tensile modulus and strength of the CNT–Al₂O₃/epoxy composites gradually increase with AR. The interrelationship between the hybrid structure and the mechanical and self-sensing behaviors of the composites are analyzed.     

Highly mechanical strength and thermally conductive bismaleimide–triazine composites reinforced by Al2O3@polyimide hybrid fiber

Bismaleimide–triazine (BT) resins have received a great deal of attention in microelectronics due to its excellent thermal stability and good retention of mechanical properties. Thereafter, developing BT based composites with high mechanical strength, thermal conductivity and dielectric property simultaneously are highly desirable. In this study, one hybrid fiber of Al₂O₃ nanoparticle (200 nm) supported on polyimide fiber (Al₂O₃@PI) with core–shell structure was introduced into BT resin to prepare promising Al₂O₃@PI–BT composite. The results indicated that the resultant composites possessed high Young’s modulus of 4.06 GPa, low dielectric constant (3.38–3.50, 100 kHz) and dielectric loss (0.0102–0.0107, 100 kHz). The Al₂O₃@PI hybrid film was also conductive to improve thermal stability (T_d5% up to 371 °C), in-plane thermal conductivity (increased by 295% compared to that of the pure BT resin). Furthermore, the Al₂O₃@PI–BT composite were employed to fabricate a printed circuit substrate, on which a frequency “flasher” circuit and electrical components worked well.     

Fracture behaviour of α-Al2O3 ceramics reinforced with a mixture of single-wall and multi-wall carbon nanotubes

The extraordinary mechanical properties of single-wall carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes (MWCNTs) have generated interest in incorporating them as toughening agents in ceramics. This work describes the fracture behaviour of an alumina (Al₂O₃) ceramic reinforced with a mixture of 0.05 wt% MWCNTs + 0.05 wt% SWCNTs. The CNT/Al₂O₃ nanocomposite was pressureless sintered in air using graphite powder as bed powder at 1520 °C for 1 h. The hardnesses and fracture toughnesses were lower than for pure Al₂O₃ and Al₂O₃ + 0.1 wt% SWCNTs and Al₂O₃ + 0.1 wt% MWCNTs. A predominantly transgranular fracture mode with a decrease in crack deflection and no pull-out was observed in the SWCNT + MWCNT–Al₂O₃ nanocomposite. MWCNTs had to the best reinforcing effect in Al₂O₃ nanocomposite.     

Manufacturing techniques and property evaluations of conductive composite yarns coated with polypropylene and multi-walled carbon nanotubes

This study uses a melt extrusion method, a method for producing wires, to coat polyester (PET) yarns with polypropylene (PP) and multi-walled carbon nanotubes (MWCNTs). The resulting PP/MWCNTs-coated PET conductive yarns are tested for their tensile properties, processability, morphology, melting and crystallization behaviors, electrical conductivity, and applications. The test results indicate that tensile strength of the conductive yarns increases with an increase in the coiling speed that contributes to a more single-direction-orientated MWCNTs arrangement as well as a greater adhesion between PP/MWCNTs and PET yarns. 8 wt% MWCNTs results in an 18 °C higher crystallization temperature (T_c) of PP and an electrical conductivity of 0.8862 S/cm. The test results of this study have proven that this form of processing technology can prepare PP/MWCNTs-coated PET conductive yarns that have satisfactory tensile properties and electrical conductivity, and can be used in functional woven fabrics and knitted fabrics.     

Effect of silica coating thickness on the thermal conductivity of polyurethane/SiO2 coated multiwalled carbon nanotube composites

Silica coated multiwalled carbon nanotubes (SiO₂@MWCNTs) with different coating thicknesses of ∼4 nm, 30–50 nm, and 70–90 nm were synthesized by a sol–gel method and compounded with polyurethane (PU). The effects of SiO₂@MWCNTs on the electrical properties and thermal conductivity of the resulting PU/SiO₂@MWCNT composites were investigated. The SiO₂ coating maintained the high electrical resistivity of pure PU. Meanwhile, incorporating 0.5, 0.75 and 1.0 wt% SiO₂@MWCNT (70–90 nm) into PU, produced thermal conductivity values of 0.287, 0.289 and 0.310 W/mK, respectively, representing increases of 62.1%, 63.3% and 75.1%. The thermal conductivity of PU/SiO₂@MWCNT composites was also increased by increasing the thickness of the SiO₂ coating.     

Room temperature multiferroic properties of (Bi0.95La0.05)(Fe0.97Mn0.03)O3/NiFe2O4 double layered thin film

(Bi_0.95La_0.05)(Fe_0.97Mn_0.03)O₃/NiFe₂O₄ double layered thin film was prepared on a Pt(111)/Ti/SiO₂/Si(100) substrate by a chemical solution deposition method. X-ray diffraction and Raman scattering spectroscopy studies confirmed the formation of the distorted rhombohedral perovskite and the inverse spinel cubic structures for the (Bi_0.95La_0.05)(Fe_0.97Mn_0.03)O₃/NiFe₂O₄ double layered thin film. The (Bi_0.95La_0.05)(Fe_0.97Mn_0.03)O₃/NiFe₂O₄ double layered thin film exhibited well saturated ferromagnetic (2 M_r of 18.1 emu/cm³ and 2H_c of 0.32 kOe at 20 kOe) and ferroelectric (2P_r of 60 μC/cm² and 2E_c of 813 kV/cm at 866 kV/cm) hysteresis loops with low order of leakage current density (4.5 × 10⁻⁶ A/cm² at an applied electric field of 100 kV/cm), which suggest the ferroelectric and ferromagnetic multi-layers applications in real devices.     

Efficient purification of His-tagged protein by superparamagnetic Fe3O4/Au–ANTA–Co2 + nanoparticles

Superparamagnetic Fe₃O₄/Au nanoparticles were synthesized and surface modified with mercaptopropionic acid (MPA), followed by conjugating Nα,Nα-Bis(carboxymethyl)-l-lysine hydrate (ANTA) and subsequently chelating Co^2 +. The resulting Fe₃O₄/Au–ANTA–Co^2 + nanoparticles have an average size of 210 nm in aqueous solution, and a magnetization of 36 emu/g, endowing the magnetic nanoparticles with excellent magnetic responsivity and dispersity. The Co^2 + ions in the magnetic nanoparticle shell provide docking site for histidine, and the Fe₃O₄/Au–ANTA–Co^2 + nanoparticles exhibit excellent performance in binding of a His-tagged protein with a binding capacity of 74 μg/mg. The magnetic nanoparticles show highly selective purification of the His-tagged protein from Escherichia coli lysate. Therefore, the obtained Fe₃O₄/Au–ANTA–Co^2 + nanoparticles exhibited excellent performance in the direct separation of His-tagged protein from cell lysate.     

Structure-dielectric properties relationships in copper-substituted magnesium ferrites

Nanocrystalline powders of copper-substituted magnesium ferrites with general formula Mg_1−xCu_xFe₂O₄ (x = 0.00, 0.17, 0.34, 0.50, 0.67, 0.84, 1.00) were prepared for the first time by sol–gel auto-combustion method, using glycine as fuel agent. Solid phase chemical reactions and the occurrence of spinel structure were monitored by using infrared spectroscopy. X-ray diffraction analysis confirmed the spinel single-phase formation. A shift from cubic structure to tetragonal structure starting with x = 0.84 was also observed. Microstructure of the samples was analyzed by scanning electron microscopy and particle size was estimated from the micrographs.Analysis of dielectric properties revealed very low values of dielectric loss at frequencies over 10 MHz.     

Magneto acoustical emission in nanocrystalline Mn–Zn ferrites

Mn_0.4Zn_0.6Fe₂O₄ powders were prepared by microwave hydrothermal method. The powders were characterized by X-ray diffraction, transmission electron microscope. The powders were sintered at different temperatures 400, 500, 600, 700, 800 and 900 °C/30 min using microwave sintering method. The grain size was estimated by scanning electron microscope. The room temperature dielectric and magnetic properties were studied in the frequency range (100 kHz–1.8 GHz). The magnetization properties were measured upto 1.5 T. The acoustic emission has been measured along the hysteresis loops from 80 K to Curie temperature. It is found that the magneto-acoustic emission (MAE) activity along hysteresis loop is proportional to the hysteresis losses during the same loop. This law has been verified on series of polycrystalline ferrites and found that the law is valid whatever the composition, the grain size and temperature. It is also found that the domain wall creation/or annihilation processes are the origin of the MAE.     

Influence of Ga3+ ions on spectroscopic and dielectric features of multi component lithium lead boro bismuth silicate glasses doped with manganese ions

Multi-component glasses of the chemical composition 19.5Li₂O–20PbO–20B₂O₃–30SiO–(10 − x)Bi₂O₃–0.5MnO:xGa₂O₃ with 0 ≤ x ≤ 5.0 have been synthesized. Spectroscopic (optical absorption, IR, Raman and ESR) and dielectric properties were investigated. Optical absorption and ESR spectral studies have indicated that managanese ions do exist in Mn³⁺ state in addition to Mn²⁺ state in the samples containing low concentration of Ga₂O₃. The IR and Raman studies indicated increasing degree of disorder in the glass network with the concentration of Ga₂O₃ up to 3.0 mol%. The dielectric constant, loss and ac conductivity are observed to increase with the concentration of Ga₂O₃ up to 3.0 mol%. The quantitative analysis of the results of dielectric properties has indicated an increase in the insulating strength of the glasses as the concentration of Ga₂O₃ is raised beyond 3.0 mol%. This has been attributed to adaption of gallium ions from octahedral to tetrahedral coordination.