Enhanced conductivity behavior of polydimethylsiloxane (PDMS) hybrid composites containing exfoliated graphite nanoplatelets and carbon nanotubes

Polydimethylsiloxane (PDMS) hybrid composites consisting of exfoliated graphite nanoplatelets (xGnPs) and multiwalled carbon nanotubes functionalized with hydroxyl groups (MWCNTs-OH) were fabricated, and the effects of the xGnP/MWCNT-OH ratio on the thermal, electrical, and mechanical properties of polydimethylsiloxane (PDMS) hybrid composites were investigated. With the total filler content fixed at 4 wt%, a hybrid composite consisting of 75% × GnP/25% MWCNT-OH showed the highest thermal conductivity (0.392 W/m K) and electrical conductivity (1.24 × 10⁻³ S/m), which significantly exceeded the values shown by either of the respective single filler composites. The increased thermal and electrical conductivity found when both fillers are used in combination is attributed to the synergistic effect between the fillers that forms an interconnected hybrid network. In contrast, the various different combinations of the fillers only showed a modest effect on the mechanical behavior, thermal stability, and thermal expansion of the PDMS composite.     

Preparation and characterization of poly(3-octylthiophene)/carbon fiber thermoelectric composite materials

Poly(3-alkylthiophene) (P3AT) with a high Seebeck coefficient has recently been reported. However, P3AT/inorganic conductive composites exhibit relatively poor thermoelectric performance because of their low electrical conductivity. In this work, carbon fiber sheets with a high electrical conductivity were chosen as the inorganic phase, and poly(3-octylthiophene)(P3OT)/carbon fiber composites were prepared by casting P3OT solution onto the carbon fiber sheets. The carbon fiber sheets incorporated into the composites can provide good electrical conductivity, and P3OT can provide a high Seebeck coefficient. The highest power factor of 7.05 μW m⁻¹ K⁻² was obtained for the composite with 50 wt% P3OT. This work suggests a promising method for preparing large-scale thermoelectric composites with excellent properties.     

Preparation,morphology and properties of acid and amine modified multiwalled carbon nanotube/polyimide composite

The precursor of polyimide, polyamic acid, was prepared by reacting 4,4′-oxydianiline (ODA) with 3,3′,4,4′-benzophenone tetracarboxylic dianhydride (BTDA). Unmodified, acid-modified and amine-modified multiwall carbon nanotubes (MWCNT) were separately added to the polyamic acid and heated to 300 °C to produce polyimide/carbon nanotube composite. Scanning electron microscopic (SEM) and transmission electron microscopic (TEM) microphotographs reveal that acid-modified MWCNT and amine-modified MWCNT were dispersed uniformly in the polyimide matrix. The effect of the acid and amine-modified MWCNTs on the surface and volume electrical resistivities of MWCNT/polyimide composites were investigated . The surface electrical resistivity of the nanocomposites decreased from 1.28 × 10¹⁵ Ω/cm² (neat polyimide) to 7.59 × 10⁶ Ω/cm² (6.98 wt% unmodified MWCNT content). Adding MWCNTs influenced the glass transition temperatures of the nanocomposites. Modified MWCNTs significance enhanced the mechanical properties of the nanocomposites. The tensile strength of the MWCNT/polyimide composite was increased from 102 MPa (neat polyimide) 134 MPa (6.98 wt% acid modified MWCNT/polyimide composites).     

Segregated poly(vinylidene fluoride)/MWCNTs composites for high-performance electromagnetic interference shielding

Conductive polymer composites (CPCs) that contain a segregated structure have attracted significant attentions because of their promising for fulfilling low filler contents with high electromagnetic interference (EMI) properties. In the present study, segregated poly(vinylidene fluoride) (PVDF)/multi-walled carbon nanotubes (MWCNTs) composites were successfully prepared by mechanical mixing and hot compaction. The PVDF/MWCNTs samples with 7 wt% filler content possess high electrical conductivities and high EMI shielding effectiveness (SE), reaching 0.06 S cm⁻¹ and 30.89 dB (in the X-band frequency region), much higher than lots of reported results for CNT-based composites. And the EMI SE greatly increased across the frequency range as the sample thickness was improved from 0.6 to 3.0 mm. The EMI shielding mechanisms were also investigated and the results demonstrated absorption dominating shielding mechanism in this segregated material. This effective preparation method is simple, low-cost, and environmentally-friendly and has potential industrial applications in the future.     

Preparation of aligned Fe3O4@Ag-nanowire/poly(vinyl alcohol) nanocomposite films via a low magnetic field

Aligned Fe₃O₄@Ag-nanowire (Ag-NW)/poly(vinyl alcohol) (PVA) nanocomposite films are prepared via a magnetic field-assisted method under a low magnetic field (B < 0.1 T) induction. The effects of the mass ratio (MR) of Fe₃O₄ to Ag-NWs and the Ag-NW content are systematically studied on the composite electrical conductivity (EC). The preferential alignment of Ag-NWs brings about a significant increase in the EC of the oriented composite in the parallel direction along the magnetic field. The optimal MR is determined to be equal to 0.15 at which the random composite has a good EC meanwhile the oriented composite shows a good response to the applied magnetic field. The oriented composite with the 20 wt% Ag-NWs shows a high EC anisotropy of ca. 6.6 and a very high EC of 4500 S/cm via the external magnetic field. In addition, the introduction of Ag-NWs leads to an obvious improvement in the thermal stability of PVA composites.     

Thermally reduced graphene oxide acting as a trap for multiwall carbon nanotubes in bi-filler epoxy composites

The effect of thermally reduced graphene oxide (TRGO) on the electrical percolation threshold of multi wall carbon nanotube (MWCNT)/epoxy cured composites is studied along with their combined rheological/electrical behavior in their suspension state. In contrast to MWCNT and carbon black (CB) based epoxy composites, there is no prominent percolation threshold for the bi-filler (TRGO–MWCNT/epoxy) composite. Furthermore, the electrical conductivity of the bi-filler composite is two orders of magnitude lower (∼1 × 10⁻⁵ S/m) than the pristine MWCNT/epoxy composites (∼1 × 10⁻³ S/m). This result is primarily due to the strong interaction between TRGO and MWCNTs. Optical micrographs of the suspension and scanning electron micrographs of the cured composites indicate trapping of MWCNTs onto TRGO sheets. A morphological model describing this interaction is presented.     

Mechanical reinforcement while remaining electrical insulation of glass fibre/polymer composites using core–shell CNT@SiO2 hybrids as fillers

Carbon nanotubes (CNTs) have been widely used as mechanical reinforcement agents of composites. However, their aggregations, weak interfacial interaction with polymer, as well as high electrical conductivity limit their use in some especial applications. In this paper, the silicon oxide (SiO₂)-coated (CNT@SiO₂) core–shell hybrids with different SiO₂ thickness were prepared and employed to reinforce glass fibre-reinforced bismaleimide–triazine (BT) resin (GFRBT) composites. The results indicated the mechanical properties, including tensile strength and Young’s modulus increased with the increase of SiO₂ thickness and CNT@SiO₂ loading. Such enhanced mechanical properties were mainly attributed to the intrinsically nature of CNTs, homogeneous dispersion of the hybrids, as well as improved interfacial interaction. Meanwhile, the composites remained high electrical insulation (9.63 × 10¹² Ω cm) due to the existence of SiO₂ layer on CNT surface. This study will guide the design of functionalized CNTs and the construction of high-performance composites.     

Study on thermal properties of graphene foam/graphene sheets filled polymer composites

The polymer composites composed of graphene foam (GF), graphene sheets (GSs) and pliable polydimethylsiloxane (PDMS) were fabricated and their thermal properties were investigated. Due to the unique interconnected structure of GF, the thermal conductivity of GF/PDMS composite reaches 0.56 W m⁻¹ K⁻¹, which is about 300% that of pure PDMS, and 20% higher than that of GS/PDMS composite with the same graphene loading of 0.7 wt%. Its coefficient of thermal expansion is (80–137) × 10⁻⁶/K within 25–150 °C, much lower than those of GS/PDMS composite and pure PDMS. In addition, it also shows superior thermal and dimensional stability. All above results demonstrate that the GF/PDMS composite is a good candidate for thermal interface materials, which could be applied in the thermal management of electronic devices, etc.     

Preparation of Nylon-6/flake graphite derivatives composites with antistatic property and thermal stability

Nylon-6/flake graphite (FG) composite, Nylon-6/graphene intercalation compounds (GIC) composite and Nylon-6/exfoliated graphite (EG) composite were prepared by FG, GIC, EG and caprolactam via in situ polymerization, and the volume resistivities of Nylon-6/flake graphite derivatives composites were also investigated. Meanwhile, the structure of Nylon-6/EG composite was characterized and the thermal stability of Nylon-6/EG composite was investigated as well. When the mass percents of FG, GIC and EG were 1%, 2–4% and 1%, the volume resistivities of flake graphite derivatives composites would reach 7.5 × 10⁶ Ω cm, 3.6 × 10⁸–1.4 × 10⁶ Ω cm and 2.3 × 10⁶ Ω cm. When the mass percent of EG increases from 0% to 9%, the thermal stability temperature of Nylon-6/EG composite would enhance from 70 to 196 °C. This shows that Nylon-6/flake graphite derivatives composites can have the antistatic property and thermal stability synchronously.     

Flame-retarded biocomposites of poly(lactic acid), distiller’s dried grains with solubles and resorcinol di(phenyl phosphate)

The distiller’s dried grains with solubles (DDGS) were treated by smashing and water washing processes. The treatment effects on DDGS were analyzed, and the results showed that the thermal stability and the hydrophobicity of DDGS were improved by the treatment processes. The flame retarded biocomposites of poly(lactic acid) (PLA) with DDGS and degradable polymeric flame retardant resorcinol di(phenyl phosphate) (RDP) were prepared. The prepared biocomposites had good mechanical properties and the tensile strength of the biocomposite containing 15 wt% RDP and 15 wt% DDGS reached approximately 53 MPa. Meanwhile, using the limited oxygen index (LOI) and the underwriters laboratory (UL-94) tests, for the biocomposite, the LOI value was approximately 27.5% and V-0 rating in UL-94 was attained. Furthermore, the peak heat release rate of this biocomposite was reduced to 275 kW/m² compared with 310 kW/m² for pure PLA. After burning of the biocomposites, compact and coherent charred layer was formed and the char residues were analyzed in detail.     

Enhanced thermal conductivity and dielectric properties of Al/β-SiCw/PVDF composites

Polymeric composites with high thermal conductivity, high dielectric permittivity but low dissipation factor have wide important applications in electronic and electrical industry. In this study, three phases composites consisting of poly(vinylidene fluoride) (PVDF), Al nanoparticles and β-silicon carbide whiskers (β-SiC_w) were prepared. The thermal conductivity, morphological and dielectric properties of the composites were investigated. The results indicate that the addition of 12 vol% β-SiC_w not only improves the thermal conductivity of Al/PVDF from 1.57 to 2.1 W/m K, but also remarkably increases the dielectric constant from 46 to 330 at 100 Hz, whereas the dielectric loss of the composites still remain at relatively low levels similar to that of Al/PVDF at a wider frequency range from 10⁻¹ Hz to 10⁷ Hz. With further increasing the β-SiC_w loading to 20 vol%, the thermal conductivity and dielectric constant of the composites continue to increase, whereas both the dielectric loss and conductivity also rise rapidly.     

Magnetically-sensitive shape memory polyurethane composites crosslinked with multi-walled carbon nanotubes

Magnetically-sensitive polyurethane composites, which were crosslinked with multi-walled carbon nanotubes (MWCNTs) and were filled with Fe₃O₄ nanoparticles, were synthesized via in situ polymerization method. MWCNTs pretreated with nitric acid were used as crosslinking agents. Because of the crosslinking of MWCNTs with polyurethane prepolymer, the properties of the composites with a high content of Fe₃O₄ nanoparticles, especially the mechanical properties, were significantly improved. The composites showed excellent shape memory properties in both 45 °C hot water and an alternating magnetic field (f = 45 kHz, H = 29.7 kA m⁻¹). The shape recovery time was less than one minute and the shape recovery rate was over 95% in the alternating magnetic field.     

Chinese ink-facilitated fabrication of carbon nanotube/polyvinyl alcohol composite sheets with a high nanotube loading

Fabricating carbon nanotube-based composites requires high degree of dispersion of carbon nanotubes into a polymer matrix. The widely used approaches reported in open literature for such a purpose are usually complicated and high-cost. Herein, we found that Chinese ink could be used to prepare composites composed of multi-walled carbon nanotubes (MWCNTs) and polyvinyl alcohol (PVA). The Chinese ink acted as a solvent and a dispersant. The MWCNT-ink-PVA ternary composite possessed both high flexibility and high electrical conductivity, with an optimized electrical conductivity of 8.17 S cm⁻¹. This simple method is believed to be applicable to other nanosacle carbon materials.     

Characterization of thermoplastic natural fibre composites made from woven hybrid yarn prepregs with different weave pattern

This paper focuses on the effect of weave structure on mechanical behaviour and moisture absorption of the PLA/hemp woven fabric composites made by compression moulding. The unidirectional woven fabric prepregs were made from PLA (warp) and PLA/hemp wrapped-spun hybrid yarn (weft) with two different weave patterns; 8-harness satin and basket. Unidirectional composites with 30 mass% hemp content were fabricated from these prepregs, and compared to winded PLA/hemp hybrid yarn laminates with same composition. The composite from the satin fabric had significantly lowest porosities and best mechanical properties compared to the composite made from the winded hybrid yarn and basket fabric. The tensile, flexural, and impact strength were 88 MPa, 113.64 MPa, and 24.24 kJ/m², respectively. The effect of weave pattern on water absorption is significant. Although the composite from hybrid yarn laminate has larger water absorption than that of the pure PLA, it exhibits lower moisture absorption than both weaves.     

Amperometric choline biosensors based on multi-wall carbon nanotubes and layer-by-layer assembly of multilayer films composed of Poly(diallyldimethylammonium chloride) and choline oxidase

A layer-by-layer deposition technique combined with Multi-wall carbon nanotubes (MWCNTs) was employed for fabricating choline sensors. The terminals and side-walls were linked with oxygen-containing groups when MWCNTs were treated with concentrated acid mixtures. A film of MWCNTs was initially prepared on the platinum electrode surface. Based on the electrostatic interaction between positively charged polyallylamine (PAA) and negatively charged MWCNTs and poly(vinyl sulfate) (PVS), a polymer film of (PVS/PAA)₃ was alternately adsorbed on the modified electrode continuously to be used as a permselective layer. Then poly(diallyldimethylammonium) (PDDA) and choline oxidase(ChOx) multilayer films were assembled layer-by-layer on the pretreated electrode, so an amplified biosensor toward choline was constructed. The choline sensor showed a linear response range of 5 × 10^? 7 to 1 × 10^? 4 M with a detection limit of 2 × 10^? 7 M estimated at a signal-to-noise ratio of 3, and a sensitivity of 12.53 μA/mM with a response time of 7.6 s in the presence of MWCNTs. Moreover, it exhibited excellent reproducibility, long-term stability as well as good suppression of interference. This protocol could be used to immobilize other enzymes for biosensor fabrication.     

Synthesis of multiblock thermoplastic elastomers based on biodegradable poly (lactic acid) and polycaprolactone

A new biodegradable (AB)_n type of multiblock copolymers derived from poly (ε-caprolactone) (PCL) and poly (lactic acid) (PLA) was prepared via the method of the chain extending reaction among PCL oligomers, PLA oligomers and hexamethylene diisocyanate (HDI). Fourier transform infrared spectra (FTIR), ¹H NMR, thermal gravity analysis (TGA) and derivative thermograms (DTG) were used to characterize the copolymers and the results showed that PCL and PLA were coupled by the reaction between –NCO groups and terminal –OH and –COOH groups of PCL and PLA, respectively. The material displayed enhanced mechanical properties: Young's modulus was as low as 2.7 ± 0.7 MPa and elongation at break value was above 790% at the composition of PCL/PLA = 80/20 (w/w). Moreover, according to SEM micrographs interfacial adhesion of the composites was improved. Thermal degradation temperature of the composites was higher than PLA but was lower than PCL, which is an advantage for industry process.     

The effect of alkaline and silane treatments on mechanical properties and breakage of sisal fibers and poly(lactic acid)/sisal fiber composites

The main goals of this work were to study the effect of different chemical treatments on sisal fiber bundles tensile properties as well as on tensile properties of composites based on poly(lactic acid) (PLA) matrix and sisal fibers. For this purpose, sisal fibers were treated with different chemical treatments. After treating sisal fibers the tensile strength values decreased respect to untreated fiber ones, especially when the combination of NaOH + silane treatment was used. Taking into account fiber tensile properties and fiber/PLA adhesion values, composites based on silane treated fibers would show the highest tensile strength value. However, composites based on alkali treated and NaOH + silane treated fibers showed the highest tensile strength values. Finally, experimental tensile strength values of composites were compared with those values obtained using micromechanical models.     

Hydrothermal synthesis,characterization and electrical investigation of poly(para-phenylenediamine)/vanadium oxide nanocomposite nanosheets

Sheet-like mesoporous poly(paraphenylenediamine)/vanadium oxide nanocomposite has been synthesized by the hydrothermal process using the vanadium oxide V₂O₅ as inorganic precursor and paraphenylendiamine as reducing and a structure-directing agent. Such techniques as X-ray diffraction (XRD), scanning electron microscopy (SEM), thermal analysis (TG-DTA), Fourier transform infrared spectroscopy (FTIR), Raman Spectroscopy, X-ray photoelectron spectroscopy (XPS) and nitrogen adsorption/desorption isotherms (BET) have been used to characterize the structure, morphology and the texture of the material. The conductivity of the material was measured by complex impedance spectroscopy which increases from 72 × 10^?5 Ω^?1 cm^?1 at 298 K to 95 × 10^?4 Ω^?1 cm^?1 at 493 K. The Arrhenius diagram is not linear, it presents a rupture situated at 407 K and the activation energies’ average values are 0.044 eV and 0.13 eV.     

Comparison of carbon nanofiller-based polymer composite adhesives and pastes for thermal interface applications

Graphite nanoplatelets (GNP), carbon black (CB) and carbon nanotubes are extensively researched to produce thermal interface materials (TIMs). This work reports comparison of interfacial thermal conductance (ITC) of carbon nanofiller-based polymer composite adhesives and pastes. The results show that total thermal contact resistance (TTCR) of GNP/rubbery epoxy composite was the same as that of an equivalent glassy epoxy composite. Although CB-based rubbery epoxy and silicone composites can be applied as thin bondlines, their TTCRs were significantly higher than GNP/rubbery epoxy. GNP incorporation into CB/rubbery epoxy composite improves the ITC of the CB/rubbery epoxy composites but the performance of CB/GNP/rubbery epoxy was inferior to GNP/rubbery epoxy. The thermal paste of GNP/polyetheramine had TTCR of 4.8 × 10^− 6 m²·K/W which is comparable to commercial TIM-paste. The paste produced with silicone had relatively poor ITC versus that prepared with polyetheramine. The paste having smaller particle sized GNPs offers lower TTCR than that prepared with large sized GNPs. The GNP/rubbery epoxy adhesives produced from precursor pastes gave the lowest TTCRs in comparison with the other adhesives. This study suggests that GNPs offer potential for enhancing ITC of TIMs and that ITC of adhesives depends on fillers' thermal conductivity and their interfacial contact with substrates.     

High thermal conductivity of flexible polymer composites due to synergistic effect of multilayer graphene flakes and graphene foam

Research on flexible thermal interface materials (TIMs) has shown that the interconnected network of graphene foam (GF) offers effective paths of heat transportation. In this work, a variant amount of multilayer graphene flakes (MGFs) was added into 0.2 vol% GF/polydimethylsiloxane (PDMS) composite. A remarkable synergistic effect between MGF and GF in improving thermal conductivity of polymer composites is achieved. With 2.7 vol% MGFs, the thermal conductivity of MGF/GF/PDMS composite reaches 1.08 W m⁻¹ K⁻¹, which is 80%, 184% and 440% higher than that of 2.7 vol% MGF/PDMS, GF/PDMS composites and pure PDMS, respectively. The MGF/GF/PDMS composite also shows superior thermal stability. The addition of MGFs and GF decreases slightly the elongation at break, but observably increases the Young’s modulus and tensile strength of composites compared with pure PDMS. The good performance of MGF/GF/PDMS composite makes it a good TIM for possible application in thermal management of electronics.