PbS插层K4Nb6O17复合物的制备及其光催化制氢活性

采用固相法合成层状半导体K4Nb6O17,通过层间离子交换反应、胺插入反应以及硫化反应制备了纳米PbS插层的K4Nb6O17复合光催化剂(记作K4Nb6O17/PbS).利用X射线衍射(XRD),场发射扫描电镜(SEM),X射线荧光光谱仪(XRF),紫外可见漫反射(UV-Vis)和分子荧光光谱(PL)等技术对其进行表征.考察了催化剂在Na2SO3和Na2S为牺牲剂的光催化制氢活性.结果表明,PbS的插层拓展了K4Nb6O17对可见光的响应,催化制氢活性也有明显提高.在紫外光和可见光下3 h产氢量分别达到123.94和0.66 mmol/(g cat).最后讨论了插层复合催化剂光生电荷转移的机理.     

Conversion of potassium titanate nanowires into titanium oxynitride nanotubes

Tunnel-structured potassium titanate with a K(3)Ti(8)O(17) phase was synthesized by direct oxidation of titanium powder mixed with KF(aq) in water vapor at 923 K. The reaction conditions were adjusted so that uniform single crystalline potassium titanate nanowires with [010] growth direction (length: 5-30 μm, diameter: 80-100 nm) were obtained. Nitridation of the nanowires by NH(3)(g) at 973-1073 K converted the titanate nanowires into rock-salt structured cubic phase single crystalline titanium oxynitride TiN(x)O(y) nanotubes (x = 0.88, y = 0.12, length = 1-10 μm, diameter = 150-250 nm, wall thickness = 30 - 50 nm) and nanorods (x = 0.5, y = 0.5, length = 1-5 μm, diameter = 100-200 nm) with rough surfaces and [200] growth direction. The overall conversion of the titanate nanowires into the nanotubes and the nanorods can be rationalized by Ostwald ripening mechanism. We fabricated an electrode by adhering TiN(x)O(y) nanotubes (0.2 mg) on a screen-printed carbon electrode (geometric area: 0.2 cm(2)). Electrochemical impedance spectroscopy demonstrated its charge transfer resistance to be 20Ω. The electrochemical surface area of the nanotubes on the electrode was characterized by cyclic voltammetry to be 0.32 cm(2). This property suggests that the TiN(x)O(y) nanostructures can be employed as potential electrode materials for electrochemical applications.     

NiO/In2O3纳米复合材料的制备及气敏性能研究

采用水热法结合水浴法制备出了NiO/In2O3纳米复合材料,利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射仪(XRD)等对其微观形貌和晶相进行表征分析。表征结果表明,制备所得In2O3纳米微球直径为200~300 nm,其表面均匀包覆厚度约为20 nm的NiO纳米片。气敏测试结果表明,基于NiO/In2O3异质结纳米复合材料的气体传感器对甲醛的最佳工作温度为220℃;在最佳工作温度下,对浓度为1×10^-5的甲醛气体响应可达到20,响应/恢复时间分别为4 s/16 s,且具有较好的重复性和选择性。最后,对分级结构及p-n异质结对其气敏机理进行了探讨。     

Fabrication of Ni compound nanocrystal/nanocarbon composites by cooling of chloride-based fluxes

Unique Ni compound nanocrystals were successfully grown on carbon nanotubes (CNTs) by cooling a mixed chloride flux. Cup-stacked CNTs (CSCNTs) were used as the nanocarbon materials because of their structural features. The grown nanocrystals had a nanosheet structure, which was densely assembled and had a ribbon-like morphology. Therefore, the nanocrystal/CSCNT composites were expected to have a highly active surface area for the catalyst composites. The selected area electron diffraction pattern and the related radial intensity profiles indicated that the grown nanocrystals were Ni(OH)2. When the pristine CSCNTs were used as a starting material, the formation efficiency of the nanocrystal/CSCNT composites decreased because the pristine CSCNTs were not dispersed in the KCl-LiCl flux. Therefore, functionalization of the CSCNTs was carried out with VUV light irradiation. The dispersibility of the VUV light-treated CSCNTs increased in the KCl-LiCl flux in comparison with the pristine CSCNTs because oxygen-containing functional groups, such as -COOH and -CO, were introduced onto the surfaces of the CSCNTs.     

Influence of single wall carbon nanotubes and thermal treatment on the morphology of polymer thin films

Homogeneous and stable thin films of poly(butylene terephthalate) PBT and its nanocomposites based on single wall carbon nanotubes (SWCNTs) were prepared by spin coating. PBT thin films show crystalline structures for thicknesses above 40 nm, consisting of submicrometer size 2D-spherulites. In the case of nanocomposites, carbon nanotubes act as nucleating agents and provide a template for the crystallization of PBT. This gives rise to hybrid shish-kebab structures, even in the thinnest films (∼10 nm thick). Melting and recrystallization provoke the crystallization of PBT and its nanocomposites, and can be used to control morphology. For PBT thin films, the orientation of crystalline lamellae undergoes a transformation, changing from a disposition perpendicular to the substrate (“edge-on”) to a parallel arrangement (“flat-on”) after recrystallization. In the case of the nanocomposites, the CNT influence on the polymer crystallization morphology in thin films is less significant than in the bulk due to the effect of the substrate interactions. Using Raman microscopy it is possible to directly observe both, the degree of dispersion and the location of carbon nanotubes in the films. The results reveal that bigger agglomerates act as more effective nucleating points than isolated bundles of SWCNTs during crystallization of the polymer matrix.     

层状半导体K_4Nb_6O_(17)光催化研究进展

阐述了半导体光催化分解水的基本原理,介绍了新型光催化剂K4Nb6O17的结构及制备方法,对K4Nb6O17的金属负载、离子掺杂以及插层复合等改性方法进行综述,并就K4Nb6O17作为光催化剂的前景进行了展望。     

Electrical and optical properties of reduced graphene oxide and multi-walled carbon nanotubes based nanocomposites: A comparative study

Graphene and multi-walled carbon nanotubes have attracted interest for a number of potential applications. One of the most actively pursued applications uses graphene and carbon nanotubes as a transparent conducting electrode in solar cells, displays or touch screens. In this work, in situ reduced graphene oxide/Poly (vinyl alcohol) and multi-walled carbon nanotubes/Sodium Dodecyl Sulfate/Poly (vinyl alcohol) composites were prepared by water dispersion and different reduction treatments. Comparative studies were conducted to explore the electrical and optical properties of nanocomposites based on graphene and multi-walled carbon nanotubes. A thermal reduction of graphene oxide was more effective, producing films with sheet resistances as low as 10²–10³ Ω/square with 80% transmittance for 550 nm light. The percolation threshold of the thermally reduced graphene oxide composites (0.35 vol%) was much lower than that of the chemically reduced graphene oxide composites (0.57 vol%), and than that of the carbon nanotubes composites (0.47 vol%). The Seebeck coefficient of graphene oxide films changes from about 40 μV/K to −30 μV/K after an annealing of three hours at 200 °C. The optical absorption of the nanocomposites showed a high absorbance in near UV regions and the photoluminescence enhancement was achieved at 1 wt% graphene loading, while the carbon nanotubes based composite presents a significant emission at 0.7 wt% followed with a photoluminescence quenching at higher fraction of the nanofillers 1.6 wt% TRGO and 1 wt% MWCNTs.     

Synthesis of lead-free (K, Na)(Nb, Ta)O3 nanopowders using a sol-gel process

Lead-free (K0.5Na0.5)(Nb0.7Ta0.3)O3 piezoelectric material was successfully synthesized via a sol-gel process. Crystalline (K0.5Na0.5)(Nb0.7Ta0.3)O3 nanopowders were obtained after heat treatment at 700 degrees C. The particle size was estimated to be 87nm +/- 23 nm. The transmission electron microscopy images showed that individual nanoparticles were single crystalline and had a pseudo-cubic structure with a lattice parameter of -3.96 angstroms. Both X-ray diffraction and scanning electron microscopy studies consistently showed that the crystallization of the (K0.5Na0.5)(Nb0.7Ta0.3)O3 occurred slightly above 500 degrees C. The samples have an appropriate stoichiometry as found via energy dispersive X-ray spectroscopy. The demonstration of the synthesis of (K0.5Na0.5)(Nb0.7Ta0.3)O3 via a sol-gel process as presented in this paper can provide an important foundation for the development of a synthetic route towards (K0.5Na0.5)(Nb0.7Ta0.3)O3 doped with various other elements for high performance piezoelectric devices.     

Tri‐s‐triazine‐Based Crystalline Carbon Nitride Nanosheets for an Improved Hydrogen Evolution

Tri‐s‐triazine‐based crystalline carbon nitride nanosheets (CCNNSs) have been successfully extracted via a conventional and cost‐effective sonication–centrifugation process. These CCNNSs possess a highly defined and unambiguous structure with minimal thickness, large aspect ratios, homogeneous tri‐s‐triazine‐based units, and high crystallinity. These tri‐s‐triazine‐based CCNNSs show significantly enhanced photocatalytic hydrogen generation activity under visible light than g‐C₃N₄, poly (triazine imide)/Li⁺ Cl^–, and bulk tri‐s‐triazine‐based crystalline carbon nitrides. A highly apparent quantum efficiency of 8.57% at 420 nm for hydrogen production from aqueous methanol feedstock can be achieved from tri‐s‐triazine‐based CCNNSs, exceeding most of the reported carbon nitride nanosheets. Benefiting from the inherent structure of 2D crystals, the ultrathin tri‐s‐triazine‐based CCNNSs provide a broad range of application prospects in the fields of bioimaging, and energy storage and conversion.     

Recent progress in the development and properties of novel metal matrix nanocomposites reinforced with carbon nanotubes and graphene nanosheets

One-dimensional carbon nanotubes and two-dimensional graphene nanosheets with unique electrical, mechanical and thermal properties are attractive reinforcements for fabricating light weight, high strength and high performance metal-matrix composites. Rapid advances of nanotechnology in recent years enable the development of advanced metal matrix nanocomposites for structural engineering and functional device applications. This review focuses on the recent development in the synthesis, property characterization and application of aluminum, magnesium, and transition metal-based composites reinforced with carbon nanotubes and graphene nanosheets. These include processing strategies of carbonaceous nanomaterials and their composites, mechanical and tribological responses, corrosion, electrical and thermal properties as well as hydrogen storage and electrocatalytic behaviors. The effects of nanomaterial dispersion in the metal matrix and the formation of interfacial precipitates on these properties are also addressed. Particular attention is paid to the fundamentals and the structure–property relationships of such novel nanocomposites.     

Bio-nanocomposites by assembling of gelatin and layered perovskite mixed oxides

A new class of bio-nanocomposites based on hybrid gelatin-perovskite hydrogels was prepared by mixing exfoliated perovskite-tetraalkylammonium species in aqueous suspensions with gelatin solutions. Colloidal nanosheets derived from the CsCa2Nb3O10 layered perovskite re-stacked in the gelatin solutions give bio-nanocomposite materials with different content in the inorganic moiety. These films can be easily processed as homogeneous self-supported films. The partial exfoliation of the pristine mixed oxide is produced from alkylammonium exchanged phases, being the tetraalkylammonium ions (tetraethylammonium, TEA+) an efficient intermediate to give the colloid phase constituted by well exfoliated materials useful to generate homogeneous films. The nanosheets are highly oriented in the bio-nanocomposite films in agreement with the XRD patterns and the FTIR dichroism. This orientation could be considered as a characteristic of this type of hybrid materials leading to new potential applications. In this way, we have observed that the assembling of perovskite to gelatin produces a greater increase of the dielectric permittivity than the dielectric loss in the studied samples.     

One-step preparation of FeCo nanoparticles in a SBA-16 matrix as catalysts for carbon nanotubes growth

Nanocomposites containing FeCo alloy nanoparticles dispersed in a highly ordered 3D cubic Im3m mesoporous silica (SBA-16) matrix were prepared by a novel, single-step templated-assisted sol-gel technique. Two different approaches were used in the synthesis of nanocomposites; a pure SBA-16 sample was also prepared for comparison. Low-angle X-ray diffraction, transmission electron microscopy and N2 physisorption at 77 K show that after metal loading, calcination at 500 degrees C and reduction in H2 flux at 800 degrees C the nanocomposites retain the cubic mesoporous structure with pore size not very different from the pure matrix. X-ray absorption fine structure (EXAFS) analysis at Fe and Co K-edges demonstrates that the FeCo nanoparticles have the typical bcc structure. The final nanocomposites were tested as catalysts for the production of carbon nanotubes by catalytic chemical vapour deposition and high-resolution TEM shows that good quality multi-walled carbon nanotubes are obtained.     

Oxygen Barrier of Multiwalled Carbon Nanotube/Polymethyl Methacrylate Nanocomposites Prepared by in situ Method

Multiwalled carbon nanotubes (MWCNTs)/poly(methyl methacrylate) (PMMA) nanocomposites were prepared by ultrasonic assisted emulsifier free emulsion polymerization technique with variable concentration of functionalized carbon nanotubes. MWCNTs were functionalized with H 2 SO 4 and HNO 3 with continuing sonication and polished by H 2 O 2 . The appearance of Fourier transform infrared absorption bands in the PMMA/MWCNT nanocomposites showed that the functionalized MWCNT interacted chemically with PMMA macromolecules. The surface morphology of functionalized MWCNT and PMMA/MWCNT nanocomposites were studied by scanning electron microscopy. The dispersion of MWCNT in PMMA matrix was evidenced by high resolution transmission electron microscopy. The oxygen permeability of PMMA/MWCNT nanocomposites gradually decreased with increasing MWCNT concentrations.     

An efficientfficient,controllable and facile two-step synthesis strategy: Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@RGO composites with various Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanoparticles and their supercapacitance properties

An efficient,controllable,and facile two-step synthetic strategy to prepare graphene-based nanocomposites is proposed.A series of Fe3O4-decorated reduced graphene oxide (Fe3O4@RGO) nanocomposites incorporating Fe3O4 nanocrystals of various sizes were prepared by an ethanothermal method using graphene oxide (GO) and monodisperse Fe3O4 nanocrystals with diameters ranging from 4 to 10 nm.The morphologies and microstructures of the as-prepared composites were characterized by X-ray diffraction,Raman spectroscopy,nitrogen adsorption measurements,and transmission electron microscopy.The results show that GO can be reduced to graphene during the ethanothermal process,and that the Fe3O4 nanocrystals are well dispersed on the graphene sheets generated in the process.The analysis of the electrochemical properties of the Fe3O4@RGO materials shows that nanocomposites prepared with Fe3O4 nanocrystals of different sizes exhibit different electrochemical performances.Among all samples,Fe3O4@RGO prepared with Fe3O4 nanocrystals of 6 nm diameter possessed the highest specific capacitance of 481 F/g at 1 A/g,highlighting the excellent capability of this material.This work illustrates a promising route to develop graphene-based nanocomposite materials with a wide range of potential applications.     

Effect of carbon nanotubes shape on the properties of multiwall carbon nanotubes/polyethylene flexible transparent conductive films

Transparent conductive material is used in a wide range of applications and is particularly interesting. In the present work, a series of multiwall carbon nanotubes/low density polyethylene nanocomposites with different carbon nanotubes were prepared via solution casting method. The optical transparency, morphology, and resistivity of transparent conductive films have been characterized by using UV–Vis Spectrophotometer, Field emission scanning electron microscope and Multimeter, respectively. Their electrically conductive and optically transparent properties were studied and compared. The result showed that thinner and longer multiwall carbon nanotubes were more suitable for the fabrication of flexible transparent conductive nanocomposites. The sample filled with 1 wt% of T.1 (outside diameter <8 nm, length 10–30 μm) had good transparent conductive properties (volume conductivity of 3.12 × 10^?3 S m^?1 and optical transmittance of 62.8 % at the light wavelength of 600 nm). The high volume conductivity and optical transparency demonstrated that such kind of nanocomposite films had favorable potential in the applications from electromagnetic interference shielding to transparent electrodes.     

Multi wall carbon nanotubes assisted synthesis of YVO4:Eu3+ nanocomposites for display device applications

YVO₄:Eu³⁺ nanocomposites have been synthesized by means of a modified co-precipitation method (CP-CNT). Multi walled carbon nanotubes (MWCNT’s) have been employed in the synthesis of the YVO₄:Eu³⁺ nanocomposites to enhance its photoluminescence efficiency. The prepared nanocomposites were thoroughly characterized using the characterization techniques namely XRD, SEM, FTIR and Raman scattering. To evaluate the potentiality of the prepared nanocomposites, the same phosphor has also been prepared by using co-precipitation (CP) method without employing multi walled carbon nanotubes and also by means of conventional solid state reaction method (SSR). The photoluminescence spectra of YVO₄:Eu³⁺ nanocomposites have shown stronger red emission at 619 nm (⁵D₀ → ⁷F₂) for both the excitation wavelengths (254 and 393 nm) than the other two prepared samples. The effect of MWCNT’s on photoluminescent properties of the YVO₄:Eu³⁺ nanocomposites is also explained.     

Preparation of porous chromium oxide nanotubes using carbon nanotubes as templates and their application as an ethanol sensor

Chromium oxide nanotubes were successfully prepared using multi-walled carbon nanotubes (MWCNTs) as a template via a supercritical fluid-mediated route. In this method, with chromium (III) nitrate nonahydrate as precursor, chromium oxide was first deposited on MWCNTs in supercritical ethanol in the presence of NH(4)HCO(3). The as-prepared chromium oxide/MWCNT nanocomposites were characterized by transmission electron microscopy, x-ray diffraction, infrared spectroscopy and thermogravimetric analysis. It was demonstrated that the MWCNTs were coated with a layer of amorphous Cr(2)O(3)·xH(2)O. The thickness of the Cr(2)O(3)·xH(2)O sheath on MWCNTs could be tuned by manipulating the ratio of precursor to MWCNTs. Calcining the composites at 550?°C, the MWCNTs were removed, producing polycrystalline α-Cr(2)O(3) nanotubes. The as-prepared α-Cr(2)O(3) sample was used as a sensor material to detect ethanol vapor, and it was demonstrated that the α-Cr(2)O(3) nanotubes exhibited good performance even at 400?°C.     

Lepidocrocite-like ferrititanate nanosheets and their full exfoliation with quaternary ammonium compounds

Efficient methods for the synthesis of layered structure nanomaterials (nanosheets), their complete exfoliation (delamination) into the layers of atomic thickness and design of organic–inorganic nanohybrids present important stages toward development of improved polymer-based nanocomposites and pillared heterostructures with potential application in purification technologies such as photocatalysis. A rapid and efficient exfoliation process of protonated layered ferrititanates with lepidocrocite-like structure and formation of organic–inorganic nanohybrids is performed starting from the nanosheets composed of only a few host layers and nanometric lateral dimensions using quaternary ammonium compounds. These nanosheets are initially synthesized from a highly abundant precursor through an alkaline hydrothermal route. We demonstrated that dimethyldioctadecylammonium cations strongly interact with the exfoliated single host layers (0.75 nm thick) providing thermal stability (~ 500 °C) to the as-prepared organic–inorganic nanohybrid over the temperature range commonly applied for the processing of thermoplastic nanocomposites.     

Self‐Assembled Hybrid Materials Based on Organic Nanocrystals and Carbon Nanotubes

Organic crystalline materials are used as dyes/pigments, pharmaceuticals, and active components of photonic and electronic devices. There is great interest in integrating organic crystals with inorganic and carbon nanomaterials to create nanocomposites with enhanced properties. Such efforts are hampered by the difficulties in interfacing organic crystals with dissimilar materials. Here, an approach that employs organic nanocrystallization is presented to fabricate solution‐processed organic nanocrystal/carbon nanotube (ONC/CNT) hybrid materials based on readily available organic dyes (perylene diimides (PDIs)) and carbon nanotubes. The hybrids are prepared by self‐assembly in aqueous media to afford free‐standing films with tunable CNT content. These exhibit excellent conductivities (as high as 5.78 ± 0.56 S m^?1), and high thermal stability that are superior to common polymer/CNT hybrids. The color of the hybrids can be tuned by adding various PDI derivatives. ONC/CNT hybrids represent a novel class of nanocomposites, applicable as optoelectronic and conductive colorant materials.     

Two Alternative Routes to MS2 Nanotubes

Inorganic tubular nanostructure MS2 （M=Mo, W, Nb, Ta） were synthesized by two alternative routes. Thermal decomposition method was used for producing fullerence-like MS2 （M=Mo, W） nanotubes on Al2O3 template using ammonium sulfur respectively; NbS2, and TaS2 nanotubes were obtained successfully by reducing corresponding metal trisulfide in a stream of H2 （mixed with N2 in some cases） at elevated temperatures.Detailed experimental procedure, and the characterization of associated results, were evaluated using X-ray diffraction （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and high resolution transmission electron microscopy （HRTEM）. The result reveals that products are composed of high density of MS2 tubular nanostructures with the diameter of 100 nm and length of tens of micrometers. And no mistake, these 1-D （one-dimensional） tubular nanomaterials added quantities and varieties in the growing family of nanotubes of inorganic layered materials.