共查询到20条相似文献,搜索用时 46 毫秒
1.
由于脉冲激光源在烧蚀激发声脉冲时,其时域特性非常接近于理想的δ(t)函数,因此激光超声技术不仅可用于复杂的各向异性媒质声的激发和传播理论作实验验证,而且由于它的非接触激发和接收特性,也已成为各向异性材料特性检测的有效手段。单晶硅是晶格常数为5.43A的立方晶体,它的密度p=2.332g/cm3。对于(110)晶面,它的弹性常数约为:C11=C22=194.36GPa,C12=35.24GPa,C33=165.7GPa,C13=C23=63.9GPa,C44=C55=79.56GPa,C66=50… 相似文献
2.
激光光强分布测量中面阵CCD信号畸变的校正 总被引:1,自引:0,他引:1
当面阵CCD用于激光能量空间分布测量时,由于CCD探测器光电响应非线性、光电响应非均匀性等因素影响,必然使信号产生畸变。本文通过理论分析与实验对畸变进行了校正,收到了良好的效果。 相似文献
3.
瓦级激光功率基准器的研究 总被引:2,自引:0,他引:2
对称型瓦级电校准激光功率计(ECLR)采用了一系列新的设计方案,实现了光电加热区的“对准”功能,减小了由加热区不等效引起的误差,并通过双表面测量结构大辐度降低了由测温区温度分布变化带来的误差。此外,还设计了一种无窗口的热屏蔽结构,以避免由窗口所带来的误差因素。对称型瓦级ECLR在室温下测量瓦级激光功率可达到很高的精度,适用作基(标)准器。 相似文献
4.
首次提出了菱形形位相元结构的随机位相板,用衍射理论分析了经这种随机位相板变换后的激光在远场的光斑特性。结果表明其能量利用率高于其它随机位相板用面阵CCD记录的远场光斑,经计算机处理后得到的光斑包络与数值计算结果一致。 相似文献
5.
利用线阵CCD实现宽波段、大视场短脉冲激光波长的远场测量 总被引:5,自引:1,他引:4
介绍了一种利用线阵CCD实现宽波段、大视场脉冲激光波长及方向远场测量的原理和实验装置;对强烈背景下激光信号的提取与处理方法进行了理论分析和实验研究,给出了系统信噪比与探测器件工作频率的理论公式;最后简要介绍了远场实验和测试结果 相似文献
6.
铝合金表面激光熔敷铜基复合材料涂层的工艺和组织 总被引:3,自引:1,他引:2
在ZL104铝合金表面激光熔敷铜基混合粉末(w(B)/%:20Ni,8.0Co5.0Fe,6.8Mo,1.5Cr,3.5Si,0.2RE,其余为Cu),制备了高硬度铜基复合材料涂层。研究发现,熔敷层稀释率随光宽度和扫描速度增大而减小,随激光束产大而显著增大; 相似文献
7.
8.
灰铸铁表面高功率CO2激光硬化行为的研究 总被引:4,自引:0,他引:4
利用正交试验法研究了高功率CO2激光工艺参数对灰铸铁硬化效果的影响。通过扫描电镜观察了熔化处理试样在熔池不同部位的组织特征,利用显微硬度计测定了硬化层硬度的分布规律。采用计算机回归处理分析得出了P、D、V、E对硬化层面积大小因子tB影响的表达式,并讨论了熔池各部位组织的成因。研究结果为高功率CO2激光强化处理大尺寸灰铸铁模具提供了一定的依据。 相似文献
9.
本文报道了SiH4/C2H4体系激光合成SiC超细粉研究及对合成的SiC超细粉进行的TEM(TED)、XRD、FTIR、XPS及Raman散射等测试分析。在部分样品中发现了SiC空心颗粒,讨论了SiC超细粉的成核成长规律,得出了一些有价值的新结果:SiC超细粉的合成由Si成核生长和碳化组成;反应温度较高时,为获得接近化学计量化的SiC超细粉,要求有较高的源气C/Si比,并且高的C/Si比有利于降低 相似文献
10.
自由声场自适应有源噪声控制中误差传感器的布放 总被引:6,自引:1,他引:6
合理地布放误差传感器可以减小自适应有源噪声控制系统的复杂性,提高降噪量。本文研究了自由声场条件下误差传感器布放与AANC系统降噪效果的关系,从理论和实验两个方面总结了自由场误差传感器布放规律。 相似文献
11.
以半导体激光器为光源的准直研究 总被引:4,自引:0,他引:4
对半导体激光器的准直装置、温度变化对准直精度的影响、温度控制方法作了论述。试验表明,采用半导体激光器作准直光源,准直的稳定性可达到1×10~(-6)。 相似文献
12.
13.
14.
Jogender Singh D. Poondi T. Dobbins M. Mastro Pietro 《Materials and Manufacturing Processes》2008,23(3):228-240
A novel laser-liquid-solid interaction (LLSI) technique has been developed that is highly flexible and allows engineering nanomaterials in form of particles, rods, and tubes from liquid precursors. Synthesis reaction takes place in a molecular level and reaction rate is controlled by laser energy input, precursor solution chemistry, and other processing parameters including interaction time, and thermal conductivity of solid that is spinning in the solution. By the proper selection of liquid precursor, mono-dispersed silver nanoparticles were produced with average particle size 7-10 nm. Alloy composed Ag and Ni were produced in the form of nanoparticles and nanotubes with an average diameter of 40 nm. HRTEM of nanorod exhibited that Ag acted as seed for the synthesis of immiscible of Ag-Ni alloy. Laser writing of silver exhibited 50% lower electrical resistivity and eliminated many intermediate steps involved as compared to conventional silver patterning process. 相似文献
15.
本文叙述了 HP- GL与 QUICK BASIC语言的混合编程在扫描式激光标记机上的应用 ,可方便地同时标记出 :任意三维图形、文字、能自动累加的数字 ,且输出内容的大小、旋转角度、平面位置可任意调整 相似文献
16.
17.
We demonstrate, for the first time, an 12 mm × 12 mm 0.5%Nd,5% Y:CaF2 crystal rod having a uniformly-distributed fluorescence spectrum and capable of operating as an amplifying medium at high repetition frequencies. A small gain of 2.7 is experimentally achieved at repetition frequency of 10 Hz for a pump center wavelength of 802 nm, power and absorption efficiency, 61.2 kW and 63.7%, respectively. Spatial-uniformity degradation of the output near-field beam distribution is observed, which should be attributed to the inhomogeneity of Nd,Y:CaF2 crystal. For a pump power of 61.2 kW, the stored energy of Nd,Y:CaF2 amplifier is 3.73 J. When the input energy is 50 mJ, the output laser energy is 1.4 J of extraction efficiency up to 37.53% after four-pass amplification. 相似文献
18.
19.
A 3D unsteady state numerical model of heat transfer in the circumferential laser oxygen cutting of pipes wasdeveloped. In order to minimize the computing time required for solving the finite difference equations as much aspossible, the alternating direct 相似文献
20.
Laser bending of sheet metal is a flexible forming technique by using laser scanning. Based of temperature gradsmechanism, the temperature field of sheet metal bending process by using single laser scanning is studied with theANSYS soft. A finite element 相似文献