高体积分数B4C/ZL101复合材料力学性能的研究

高体积分数颗粒增强金属基复合材料结合了陶瓷和金属的性能优势,具有轻质、高强、高模量的特点,是一种颇具应用前景的装甲材料,但此方面的报道研究较少。采用压力浸渗法制备了颗粒体积分数为50%、不同粒径的B4C/ZL101复合材料。结果表明,预制件温度为550℃、浸渗熔体温度为750℃时,采用压力浸渗可以得到颗粒分布均匀、致密度高的复合材料,组成相简单;复合材料的力学性能表明,B4C颗粒的粒径越小,复合材料的力学性能越好。当B4C颗粒粒径为3μm时,压缩强度、抗弯强度、布氏硬度分别可达1000MPa、640MPa、285HB。     

六硼化硅(SiB6)添加剂对B4C陶瓷致密化与力学性能的影响

采用热压烧结(2000℃保温1h)制备了添加2wt%和5wt%SiB6的B4C陶瓷,研究了SiB6不同添加量对B4C陶瓷致密化和力学性能的影响.结果表明: SiB6能有效地促进B4C的烧结,并有助于提高材料的力学性能. SiB6的添加量为2wt%时,B4C陶瓷的块体密度为2.515g/cm3,是理论密度的99.5%,抗折强度和硬度分别达到426.6MPa和31.2GPa. SiB6添加量增加为5wt%时,材料的密度为2.500g/cm3,强度和硬度分别下降为387MPa和29.7GPa.不同添加量对B4C陶瓷的断裂韧性的影响不明显,添加2wt%和5wt%SiB6的B4C陶瓷的K1C分别为3.20和3.28MPa·m1/2.文中还对烧结样品的物相和影响力学性能的原因进行了讨论.     

45钢上Ni-W-Co-B4C复合镀层的制备及其摩擦学性能

利用电沉积技术在45钢表面制备了Ni-W-Co-B4C复合镀层,并研究了油润滑磨损条件下Ni-W-Co-B4C复合镀层的磨损特性.结果表明,Ni-W-Co镀层磨损形貌中有很深的犁沟,局部并有黏着磨损的特征,镀层的抗磨损性能较差;加入B4C颗粒的Ni-W-Co-B4C复合镀层磨损形貌试验中的犁沟较浅,没有发现黏着磨损现象,但B4C颗粒与金属基体结合不牢,有颗粒脱落现象.B4C颗粒含量、大小和载荷都对复合镀层的耐磨性有影响.当镀层中含有20%(体积分数)的B4C颗粒时,磨损性能最好.     

碳热还原法制备部分石墨化的C/B_4C复合粉体

以炭黑和硼酸为原料,通过碳热还原法合成了部分石墨化的C/B4C复合粉体。考察了加热温度和硼酸添加量对C/B4C复合粉体合成过程的影响,采用X射线衍射和扫描电镜等方法对C/B4C复合粉体的物相及形貌进行了分析,利用热重法研究了C/B4C复合粉体的氧化性能。研究结果表明,随着加热温度的升高,复合粉体的石墨化度增大,B4C含量下降;随着硼酸加入量的增大,复合粉体中B4C含量及其石墨化度均增大;当炭黑和硼酸加入量分别为33.21%和66.79%时,经1900℃热处理所得复合粉体的石墨化度达23.26%,B4C含量为20.63%;与工业用B4C和炭黑的混合物相比,实验室合成的C/B4C复合粉体具有较好的抗氧化性能。     

CaZrO3包覆Ni超细复合粉体的制备及其抗氧化性研究

为了提高MLCC内电极材料用镍粉的抗氧化性,本研究进行了镍粉的表面改性研究.采用化学沉淀法在镍粉表面包覆CaC2O4-Zr(C2O4)2混合物前驱体后,通过高温热处理使镍粉表面的前驱体转变成了致密的CaZrO3.考察了制备条件,如包覆试剂加入方式、搅拌速度与时间、反应温度及前驱体热处理温度等对Ni/CaZrO3复合粉体抗氧化性的影响.利用扫描电镜(SEM)对样品的形貌进行了观察.结果表明,在最佳条件下制得的Ni/CaZrO3复合粉体具有良好的抗氧化性,在400℃,空气气氛中煅烧30分钟的氧化率约为4%.     

Mg2Si对Al2O3f/AZ91D复合材料硬度的影响

采用熔体浸渗法制备Al2O3f/AZ91D复合材料,发现有Mg2Si新相生成.利用SEM,XRD等手段对其成分和组成进行了分析,研究了粘结剂的加入量对材料硬度的影响.结果表明:随着硅溶胶量的不断增大,材料硬度随之增大,当硅溶胶加入量大于10%(质量分数)时,对材料硬度的影响较小,且不利于材料的其他力学性能.     

原位生成CeB_6/B_4C陶瓷的力学性能和显微组织

通过B4C、CeO2和C的化学反应,采用原位生成法,在热压烧结的条件下制备了CeB6/B4C陶瓷材料.研究了CeB6/B4C陶瓷材料的力学性能和显微组织,并对其增韧机理进行了分析.结果表明:原位生成的CeB6/B4C陶瓷只有CeB6和B4C两相,其显微维氏硬度、抗弯强度、断裂韧性最大值分别达到40.64GPa、346.7MPa、5.95MPa·m1/2,比纯碳化硼分别提高了52.50%、17.96%、61.68%.原位生成的CeB6颗粒细晶增韧补强,B4C和CeB6颗粒之间热膨胀系数不匹配产生的残余应力导致的裂纹偏转以及沿晶断裂是CeB6/B4C陶瓷的主要增韧机制.     

Fe—C—Cr—V—B系高铬堆焊合金的显微组织及耐磨性

采用药芯焊丝埋弧堆焊方法制备含有C 1 2%～1 8%(质量分数,下同),Cr 15%～20%,V 2 0%～3 0%,B 0%～1 0%的高铬堆焊合金.借助光学显微镜、扫描电镜和X射线衍射等分析手段,研究其显微组织及碳化物分布形貌,结果表明:其显微组织由α-Fe+γ-Fe+(Fe, Cr)7C3+ (Fe, Cr)3C+Fe3(C, B)+B4C等组成,加入B4C可显著细化该堆焊合金晶粒,降低α-Fe,γ-Fe基体组织的Cr,V等合金元素的固溶量,使碳化物(Fe, Cr)7C3数量增加且呈弥散分布.另外,考察了B4C含量对高铬堆焊合金硬度及耐磨性的影响,耐磨粒磨损实验结果表明其相对磨损系数是H25Cr3Mo2MnV堆焊合金的6～17倍,其中碳化物颗粒四周均匀分布的α-Fe等基体组织使其可承受较大的磨粒冲击而不脱落.     

稀土铈对热作模具钢TiN系离子镀涂层性能的改进

为了解决TiN涂层的膜/基结合力不够高和高温抗氧化性不足等问题,综合利用电弧离子镀和涂层合金化技术,在4Cr5MoV热作模具钢基体上制备了添加稀土元素Ce的TiN系涂层,测定了涂层的显微硬度、孔隙率、耐磨性及膜/基结合力,并做了恒温氧化试验和抗热震性试验,以研究稀土元素Ce对TiN,Ti(Al,V)N涂层的改性作用.试验结果表明,Ce的加入能提高涂层的耐磨性,显著提高涂层的膜/基结合力,使其高温抗氧化性和抗热震性明显改善,可大大提高4Cr5MoV钢涂层热作精密模具的使用寿命和使用效果.     

高能球磨法制备铜基电触头复合材料的研究

研究了高能球磨法在制备铜基电触头复合材料的工艺中对电触头的组织结构、力学性能和导电性能的影响,并对复合材料粉末中B4C颗粒的形貌、粒度以及在铜基体中的分布情况进行了研究.试验结果表明,高能球磨法对改变增强颗粒的形貌、改善增强颗粒体的分布均匀性非常有效,而且可以有效地提高触头材料的硬度和耐磨性.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.