PMN-PT单晶淬火处理对介电性能的影响

通过淬火处理可以使弛豫型PMN-PT单晶中一些应力集中的区域产生应力场致相变,在Td处产生宏畴,从而在温谱上Td处的介电峰强化.研究表明,经淬火处理单晶谐振极化所对应的低温介电行为受到压制,主介电峰变窄,峰值变高并稍向高温方向移动;频率弥散减弱,弛豫性变小.     

A位复合铁电陶瓷Bi0.5(Na0.82K0.18)0.5TiO3-BiCrO3的介电弛豫

采用固相反应法制备了A位复合铁电陶瓷(1-x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃-xBiCrO₃(BNKT-BCx). 研究了该陶瓷在室温至500℃温度范围内的介电性能. 结果表明该陶瓷的介电温谱存在两个介电反常峰和一个介电损耗峰, 低温介电反常峰温度附近具有明显的介电常数频率依赖性, 但居里峰随频率增加基本不变, 与典型弛豫铁电体的特征不同. 将弛豫铁电体分为本征弛豫和非本征弛豫铁电体, 通过分析极化前和极化后陶瓷的介电温谱, 发现该体系低温介电反常峰温度附近的介电频率依赖性为空间电荷和缺陷偶极子极化引起的非本征弛豫.     

La2O3掺杂（Na0．5 Bi0．5）0．94 Ba0.06 TiO3无铅压电陶瓷的介电弛豫研究

采用固相合成法制备了La2O3掺杂(Na0.5Bi0.5)0.94Ba0.06TiO3无铅压电陶瓷.研究了La2O3掺杂对(Na1/2Bi1/2)TiO3陶瓷晶体结构、介电性能与介电弛豫行为的影响.XRD分析表明,在所研究的组成范围内陶瓷材料均能够形成纯钙钛矿固溶体.材料的介电常数-温度曲线显示陶瓷具有两个介电反常峰Tf和Tm.修正的居里-维斯公式较好的描述了陶瓷弥散相变特征,弥散指数随La2O3掺杂量的增加而增加.掺杂量较低的陶瓷仅在低温介电反常峰Tf附近表现出明显的频率依赖性,随掺杂量的增加,陶瓷材料在室温和低温介电反常峰Tf之间都表现出明显的频率依赖性.并根据宏畴-微畴转变理论探讨了该体系陶瓷介电弛豫特性的机理.     

(Pb1-xSrx)TiO3系铁电陶瓷介电特性的测试分析

采用常规陶瓷工艺掺杂不同含量的分析纯SiO2和La2O3,在不同烧结温度下, 制备了系列(Pb1-xSrx)TiO3(简称PST)铁电陶瓷.对所制备的PST铁电陶瓷的介电特性进行了测试分析.1250℃烧结温度较1200℃烧结温度下样品在居里点处的温度系数α有所提高,介电常数ε略高(均在103量级),介电损耗D略有降低.随着工作频率的增加,样品介电常数有较明显的下降,介电损耗D略有增加.     

稀土改性二氧化钛的电流变行为与介电性能关系

采用sol-gel法制备了掺杂稀土改性TiO2颗粒,与甲基硅油配制成电流变液,对电流变液的介电性能进行了测试,结果表明改性后TiO2电流变液的介电常数和介电损耗比纯TiO2电流变液均显著提高,其中介电常数提高2－3倍,△ε′＝ε′100Hz－ε′10kHz明显增大,1kHz的介电损耗角正切大于0．1左右电流变液的介电常数与介电损耗达到最大值。稀土掺杂引起TiO2电流变液的介电性能改变是导致改性TiO2电流变液流变学行为变化的起因。另外,电流变液介电性能温度特性的变化可用来解释电流变液的流变学性能随温度变化关系。     

Na0.5 Bi0.5 TiO3-K0.5 Bi0.5 TiO3系铁电体的相变研究

研究了(Na1-xKx)0.5Bi0.5TiO3体系x分别为0、0.08、0.16和0.20时陶瓷不同频率下的介电温谱,发现材料为弛豫型铁电体,材料的介电谱在室温到500℃的温度范围内存在一个介电常数-温度"台阶",一个介电常数-温度峰和一个介电损耗-温度峰,通过分析陶瓷不同温度下的电滞回线验证陶瓷在升温过程中产生了铁电-反铁电-顺电相变,采用铁电体成分起伏理论和内电场理论解释了这类弛豫型铁电体相变的原因.     

介电谱在镥铝石榴石晶体中的应用

为研究提拉法生长的镥铝石榴石单晶中的缺陷,采用波长为254 nm、功率为36 W的4根低压汞灯灯管,室温下在距离镥铝石榴石单晶样品15 cm远处对其进行紫外光辐照24 h,之后在样品上下两个7 mm×7 mm表面镀上电极,置于一夹具内,夹具内部由机械泵维持真空环境,外部由液氮控制温度,利用HP4194A阻抗分析仪对紫外光辐照前后的镥铝石榴石单晶进行介电谱测试。实验结果表明:紫外光辐照后的镥铝石榴石单晶的介电损耗峰出现弛豫,由该弛豫峰对频率的依赖关系表明这种介电弛豫行为是属于偶极子取向极化的弛豫型响应,由此根据偶极子的弛豫机理推断在镥铝石榴石单晶的晶格中可能存在一定数量的缺陷。     

A位复合铁电陶瓷Bi0.5(Na0.82K0.18)0.5TiO3-BiCrO3的介电弛豫

采用固相反应法制备了A位复合铁电陶瓷(1-x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃-xBiCrO₃(BNKT-BCx). 研究了该陶瓷在室温至500℃温度范围内的介电性能. 结果表明该陶瓷的介电温谱存在两个介电反常峰和一个介电损耗峰, 低温介电反常峰温度附近具有明显的介电常数频率依赖性, 但居里峰随频率增加基本不变, 与典型弛豫铁电体的特征不同. 将弛豫铁电体分为本征弛豫和非本征弛豫铁电体, 通过分析极化前和极化后陶瓷的介电温谱, 发现该体系低温介电反常峰温度附近的介电频率依赖性为空间电荷和缺陷偶极子极化引起的非本征弛豫.     

BaNb2O6掺杂Na1/2Bi1/2TiO3无铅压电陶瓷的介电弛豫

采用传统陶瓷制备方法,制备了无铅新压电陶瓷材料Na1/2Bi1/2TiO3-xBaNb2O6.研究了BaNb2O6掺杂对(Na1/2Bi1/2)TiO3陶瓷晶体结构、介电性能与介电弛豫行为的影响.XRD分析表明,在所研究的组成范围内陶瓷材料均能够形成纯钙钛矿固溶体.材料的介电常数-温度曲线显示陶瓷具有两个介电反常峰Tf和Tm,修正的居里一外斯公式较好的描述了陶瓷弥散相变特征,弥散指数随BaNb2O6掺杂量的增加而增加.该体系陶瓷表现出与典型弛豫铁电体明显不同的弛豫行为,低掺杂量的陶瓷仅在低温介电反常峰Tf附近表现出明显的频率依赖性,而高掺杂的陶瓷材料在室温和Tf之间都表现出明显的频率依赖性.并根据宏畴一微畴转变理论探讨了该体系陶瓷产生介电弛豫的机理.     

二乙烯基苯交联聚苯乙烯/金红石复合物的微波介电性能研究

研究了二乙烯基苯交联聚苯乙烯(Dvb-pst)与金红石复合物在100～1800MHz的微波频段下对不同金红石含量复合物介电参数(ε′及ε″)的影响,结果表明,在300MHz以下,复合物介电参数基本与频率无关,仅随金红石含量而增加,但在500MHz以上的频段,复合物的介电常数随频率迅速增大,而介电损耗基本不变.用IR、XPS及SEM对复合物进行表征表明,Dvb-pst与金红石的复合并非简单的物理混合,而是由Dvb-pst中的苯环和侧链上的碳与金红石中的-Ti-O生成两相界面间的六元环,从而降低了复合物的表面活化能,并产生较弱的界面极化作用,解释了复合物的介电常数随频率增加而介电损耗变化不大的原因,为研制新型的功能复合材料奠定理论基础.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.