Tunable and microwave dielectric properties of Ba0.5Sr0.5TiO3-BaWO4 composite ceramics doped with Co2O3

Co₂O₃ doped BaWO₄-Ba_0.5Sr_0.5TiO₃ composite ceramics, prepared by solid-state route, were characterized systematically, in terms of their phase compositions, microstructure and microwave dielectric properties. Doping of Co₂O₃ promoted grain growth, reduced Curie temperature and broadened phase-transition temperature range of BaWO₄-Ba_0.5Sr_0.5TiO₃, which were attributed mainly to the substitution of Co³⁺ for Ti⁴⁺ at B site in the perovskite lattice. Dielectric diffusion behaviors of the composite ceramics were discussed. The composite ceramics all had dielectric tunability of higher than 10% at 30 kV/cm and 10 kHz, with promising microwave dielectric properties. Specifically, the sample doped with 0.2 wt.% Co₂O₃ exhibited a tunability of 20%, permittivity of 225 and Q of 292 (at 1.986 GHz), making it a suitable candidate for applications in electrically tunable microwave devices.     

Modified tunable dielectric properties by addition of MgO on BaZr0.25Ti0.75O3 ceramics

Phase composition, microstructure and tunable dielectric properties of (1 − x)BaZr_0.25Ti_0.75O₃-xMgO (BZTM) composite ceramics fabricated by solid-state reaction were investigated. It was found Mg not only existed in the matrix as MgO, there was also trace amount of Mg²⁺ ions dissolved in the BZT grains, which led to Curie temperature of the BZTM composites ceramics shifting to below −100 °C. Dielectric permittivity of the BZTM composite ceramics was reduced from thousands to hundreds by manipulating the content of MgO. Johnson's phenomenological equation based on Devonshire's theory was used to describe the nonlinear dielectric permittivity of the ceramics with increasing applied DC field. With increasing content of MgO, anharmonic constant α_(T) increased monotonously. Dielectric permittivity was 672, while dielectric tunability was as high as 30.0% at 30 kV/cm and dielectric loss was around 0.0016 for the 0.6BaZr_0.25Ti_0.75O₃-0.4MgO sample at 10 kHz and room temperature.     

Dielectric and tunable characteristics of Ba0.4Sr0.6TiO3-BaWO4 composite ceramics for microwave applications

Phase compositions, microstructure and microwave dielectric properties, of BaWO₄ (BW)-Ba_0.4Sr_0.6TiO₃ (BST) composite ceramics, prepared by the traditional solid-state route, were systematically characterized. Meanwhile, mechanism of dielectric tunability of those materials was discussed. Dielectric properties of the BW-BST composites at a DC bias field near the phase transition temperature could be interpreted by using Johnson's phenomenological equation. The sample with x = 0.60 exhibited a tunability of 29.5%, a dielectric permittivity of 192 and a Q value of 231 (at 2.700 GHz), which make it a promising candidate for applications in electrically tunable microwave devices.     

Processing, dielectric properties and impedance characteristics of Na0.5Bi0.5Cu3Ti4O12 ceramics

Na_0.5Bi_0.5Cu₃Ti₄O₁₂ (NBCTO) ceramics were prepared by conventional solid-state reaction method. The phase structure, microstructure and dielectric properties of NBCTO ceramics sintered at various temperatures with different soaking time were investigated. Pure NBCTO phase could be obtained with increasing the temperature and prolonging the soaking time. High dielectric permittivity (13,495) and low dielectric loss (0.031) could be obtained when the ceramics were sintered at 1000 °C for 7.5 h. The ceramics sintered at 1000 °C for 7.5 h also showed good temperature stability (−4.00 to −0.69%) over a large temperature range from −50 to 150 °C. Complex impedances results revealed that the grain was semiconducting and the grain boundaries was insulating. The grain resistance (R_g) was 12.10 Ω cm and the grain boundary resistance (R_gb) was 2.009 × 10⁵ Ω cm when the ceramics were sintered at 1000 °C for 7.5 h.     

Microstructural evolution and dielectric properties of Cu-deficient and Cu-excess CaCu3Ti4O12 ceramics

The microstructural evolution and dielectric properties of CaCu_3−xTi₄O_12−x (3 − x = 2.8-3.05) ceramics were investigated. Normal grain growth behavior was observed at Cu/Ca ≤ 2.9, while abnormal grain growth was observed at Cu/Ca ≥ 2.95. A CuO-rich intergranular liquid phase at Cu/Ca ≥ 2.95 and angular grain morphology were the main reasons for abnormal grain growth. However, the abundant intergranular liquid at Cu/Ca = 3.05 significantly affected the relative dielectric permittivity and dielectric loss. The CuO composition is the key parameter that determines the microstructure and dielectric properties of CCTO ceramics.     

Structure and electrical properties of (1 − x)Bi0.5Na0.5TiO3-xBi0.5K0.5TiO3 ceramics near morphotropic phase boundary

The binary lead-free piezoelectric ceramics with the composition of (1 − x)Bi_0.5Na_0.5TiO₃-xBi_0.5K_0.5TiO₃ were synthesized by conventional mixed-oxide method. The phase structure transformed from rhombohedral to tetragonal phase in the range of 0.16 ≤ x ≤ 0.20. The grain sizes varied with increasing the Bi_0.5K_0.5TiO₃ content. Electrical properties of ceramics are significantly influenced by the Bi_0.5K_0.5TiO₃ content. Two phase transitions at T_t (the temperature at which the phase transition from rhombohedral to tetragonal occurs) and T_c (the Curie temperature) were observed in all the ceramics. Adding Bi_0.5K_0.5TiO₃ content caused the variations of T_t and T_c. A diffuse character was proved by the linear fitting of the modified Curie-Weiss law. Besides, the ceramics with homogeneous microstructure and excellent electrical properties were obtained at x = 0.18 and sintered at 1170 °C. The piezoelectric constant d₃₃, the electromechanical coupling factor K_p and the dielectric constant ?_r reached 144 pC/N, 0.29 and 893, respectively. The dissipation factor tan δ was 0.037.     

Influence of sintering temperature on piezoelectric properties of (K0.5Na0.5)NbO3-LiNbO3 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ have been synthesized by traditional ceramics process without cold-isostatic pressing. The effect of the content of LiNbO₃ and the sintering temperature on the phase structure, the microstructure and piezoelectric properties of (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ ceramics were investigated. The result shows that the phase structure transforms from the orthorhombic phase to tetragonal phase with the increase of the content of LiNbO₃, and the orthorhombic and tetragonal phase co-exist in (K_0.5Na_0.5)NbO₃-LiNbO₃ ceramics when the content of LiNbO₃ is about 0.06 mol. The sintering temperature of (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ decreases with the increase of the content of LiNbO₃. The optimum composition for (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ ceramics is 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃. The optimum sintering temperature of 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃ ceramics is 1080 °C. Piezoelectric properties of 0.94 (K_0.5Na_0.5)NbO₃-0.06LiNbO₃ ceramics under the optimum sintering temperature are piezoelectric constant d₃₃ of 215 pC/N, planar electromechanical coupling factor k_p of 0.41, thickness electromechanical coupling factor k_t of 0.48, the mechanical quality factor Q_m of 80, the dielectric constant of 530 and the Curie temperature T_c = 450 °C, respectively. The results indicate that 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃ piezoelectric ceramics is a promising candidate for lead-free piezoelectric ceramics.     

Dielectric properties of a new ceramic system (1 − x)Mg4Nb2O9-xCaTiO3 at microwave frequency

The microstructures and the microwave dielectric properties of the (1 − x)Mg₄Nb₂O₉-xCaTiO₃ ceramic system were investigated. In order to achieve a temperature-stable material, CaTiO₃ (τ_f ∼ 800 ppm/°C) was chosen as a τ_f compensator and added to Mg₄Nb₂O₉ (τ_f ∼ −70 ppm/°C) to form a two phase system. It was confirmed by the XRD and EDX analysis. By appropriately adjusting the x-value in the (1 − x)Mg₄Nb₂O₉-xCaTiO₃ ceramic system, near-zero τ_f value can be achieved. A new microwave dielectric material, 0.5Mg₄Nb₂O₉-0.5CaTiO₃ applicable in microwave devices is suggested and possesses the dielectric properties of a dielectric constant ?_r ∼ 24.8, a Q × f value ∼82,000 GHz (measured at 9.1 GHz) and a τ_f value ∼−0.3 ppm/°C.     

Dielectric properties of (1−x)(Mg0.95Co0.05)TiO3-xCaTiO3 ceramic system at microwave frequency

The microwave dielectric properties and the microstructures of the (1−x)MgTiO₃-xCaTiO₃ ceramic system were investigated. With partial replacement of Mg by Co, dielectric properties of the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramics can be promoted. The microwave dielectric properties are strongly correlated with the sintering temperature. At 1275°C, the 0.95(Mg_0.95Co_0.05)TiO₃-0.05CaTiO₃ ceramics possesses excellent microwave dielectric properties: a dielectric constant ε_r of 20.3, a Q×f value of 107 000 ( at 7 GHz) and a τ_f value of −22.8 ppm/°C. By appropriately adjusting the x value in the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramic system, zero τ_f value can be achieved. With x=0.07, a dielectric constant ε_γ of 21.6, a Q×f value of 92 000 (at 7 GHz) and a τ_f value of −1.8 ppm/°C was obtained for 0.93(Mg_0.95Co_0.05)TiO₃-0.07CaTiO₃ ceramics sintered at 1275°C for 4 h.     

SmAlO3-modified (K0.5Na0.5)0.95Li0.05Sb0.05Nb0.95O3 lead-free ceramics with a wide sintering temperature range

Lead-free ceramics (1 − x)(K_0.5Na_0.5)_0.95Li_0.05Sb_0.05Nb_0.95O₃-xSmAlO₃ (KNLNS-xSA) were prepared by conventional sintering technique. The phase structure, dielectric and piezoelectric properties of the ceramics were investigated. All compositions show a main perovskite structure, exhibiting room-temperature symmetries of tetragonal at x ≤ 0.0075, of pseudo-cubic at x = 0.0100. The Curie temperature of KNLNS-xSA ceramics decreases with increasing SmAlO₃ content. Moreover, the addition of SmAlO₃ can effectively broaden the sintering temperature range of the ceramics. The KNLNS-xSA ceramic with x = 0.0050 has an excellent electrical behavior of piezoelectric coefficient d₃₃ = 226 pC/N, planar mode electromechanical coupling coefficient k_p = 38%, dielectric loss tan δ = 3.0%, mechanical quality factor Q_m = 60, and Curie temperature T_C = 327 °C, suggesting that this material could be a promising lead-free piezoelectric candidate for piezoelectric applications.     

Modified (K0.5Na0.5)(Nb0.9Ta0.1)O3 ceramics with high Qm

Lead-free ceramics (K_0.5Na_0.5)(Nb_0.9Ta_0.1)O₃ (KNNT) + x mol% K₄CuNb₈O₂₃ (KCN) + y mol% MnO₂ have been prepared using the conventional solid-state reaction technique. Crystalline structures and Microstructures were analyzed by X-ray diffraction and scanning electron microscope (SEM) at room temperature. The low dielectric loss tanδ and relatively high piezoelectric properties were obtained when KCN and MnO₂ were added into KNNT ceramics. The ceramics with x = 1.0, y = 0.50 exhibited excellent piezoelectric properties: high mechanical quality factor Q_m = 1563, piezoelectric coefficient d₃₃ = 96pC/N, electromechanical coupling coefficient k_p = 42.2%, k_t = 44.5%, k₃₃ = 58.4%, relative dielectric constant ε′ = 308, tanδ = 0.4%. This material is a promising candidate for the lead-free piezoelectric transformer applications.     

Effect of Pb(Fe1/2Nb1/2)O3 modification on dielectric and piezoelectric properties of Pb(Mg1/3Nb2/3)O3-PbZr0.52Ti0.48O3 ceramics

10 mol% Pb(Fe_1/2Nb_1/2)O₃ (PFN) modified Pb(Mg_1/3Nb_2/3)O₃-PbZr_0.52Ti_0.48O₃ (PMN-PZT) relaxor ferroelectric ceramics with compositions of (0.9 − x)PMN-0.1PFN-xPZT (x = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8 and 0.9) were prepared. X-ray diffraction investigations indicated that as-prepared ceramics were of pure perovskite phase and the sample with composition of x = 0.8 was close to morphotropic phase boundary (MPB) between rhombohedral and tetragonal phase. Dielectric properties of the as-prepared ceramics were measured, and the Curie temperature (T_c) increased sharply with increasing PZT content and could be higher than 300 °C around morphotropic phase boundary (MPB) area. At 1 kHz, the sample with composition of x = 0.1 had the largest room temperature dielectric constant ?_r = 3519 and maximum dielectric constant ?_m = 20,475 at T_m, while the sample with composition of x = 0.3 possessed the maximum dielectric relaxor factor of γ = 1.94. The largest d₃₃ = 318 pC/N could be obtained from as-prepared ceramics at x = 0.9. The maximum remnant polarization (P_r = 28.3 μC/cm²) was obtained from as-prepared ceramics at x = 0.4.     

Microwave dielectric properties of La1−xBix(Mg0.5Sn0.5)O3 ceramics

The La_1−xBi_x(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the La_0.97Bi_0.03(Mg_0.5Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. An apparent density of 6.50 g cm⁻³, a dielectric constant (?_r) of 20.2, a quality factor (Q × f) of 58,100 GHz and a temperature coefficient of resonant frequency (τ_f) of −84.2 ppm °C⁻¹ were obtained for La_0.97Bi_0.03(Mg_0.5Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h.     

Dielectric properties of B2O3-doped (1 − x)LaAlO3-xSrTiO3 ceramic system at microwave frequency

The effects of B₂O₃ addition on the microwave dielectric properties and the microstructures of (1−x)LaAlO₃-xSrTiO₃ ceramics prepared by conventional solid-state routes have been investigated. Doping with 0.25 wt.% B₂O₃ can effectively promote the densification and the microwave dielectric properties of (1−x)LaAlO₃-xSrTiO₃ ceramics. It is found that LaAlO₃-SrTiO₃ ceramics can be sintered at 1400°C due to the liquid phase effect of a B₂O₃ addition observed by scanning electronic microscopy (SEM). The dielectric constant as well as the Q×f value decreases with increasing B₂O₃ content. At 1460°C, 0.46LaAlO₃-0.54SrTiO₃ ceramics with 0.25 wt.% B₂O₃ addition possesses a dielectric constant (ε_r) of 35, a Q×f value of 38,000 (at 7 GHz) and a temperature coefficients of resonant frequency (τ_f) of −1 ppm/°C.     

Electrical and luminescence properties of Er-doped Bi0.5Na0.5TiO3 ceramics

The influences of Er content on the dielectric and photoluminescence performances of Bi_0.5Na_0.5TiO₃-xEr (x = 0, 0.005, 0.01, 0.015, 0.02, 0.03) ceramics have been investigated. The results show that Bi_0.5Na_0.5TiO₃-xEr ceramics with x = 0.01 Er have maximum values of photoluminescence and piezoelectric properties. A bright green emission at 550 nm and enhanced piezoelectric response are achieved in the ceramic Bi_0.5Na_0.5TiO₃-0.01Er at room temperature. Furthermore, the photoluminescence performance of the ceramics is significantly enhanced by electric poling.     

Influence of Bi2O3 and CuO addition on low-temperature sintering and dielectric properties of Ba0.6Sr0.4TiO3 ceramics

In this study, we tried to lower the sintering temperature of Ba_0.6Sr_0.4TiO₃ (BST) ceramics by several kinds of adding methods of Bi₂O₃, CuO and CuBi₂O₄ additives. The effects of different adding methods on the microstructures and the dielectric properties of BST ceramics have been studied. In the all additive systems, the single addition of CuBi₂O₄ was the most effective way for lowering the sintering temperature of BST. When CuBi₂O₄ of 0.6 mol% was mixed with starting BST powders and sintered at 1100 °C, the derived ceramics demonstrated dense microstructure with a low dielectric constant (? = 4240), low dielectric loss (tan δ = 0.0058), high tunability (Tun = 38.3%) and high Q value (Q = 251). It was noteworthy that the sintering temperature was significantly lowered by 350 °C compared with no-additive system, and the derived ceramics maintained the excellent microwave dielectric properties corresponding to pure BST.     

Effect of BiFeO3 additions on the dielectric and piezoelectric properties of (K0.44Na0.52Li0.04)(Nb0.84Ta0.1Sb0.06)O3 ceramics

(1 − x) (K_0.44Na_0.52Li_0.04)(Nb_0.84Ta_0.1Sb_0.06)O₃ − x BiFeO₃ (x = 0, 0.002, 0.004, 0.006, 0.008, 0.01) lead-free piezoelectric ceramics were prepared by the conventional ceramic processing. The compositional dependence of the phase structure and the electrical properties of the ceramics were studied. A morphotropic phase boundary between the orthorhombic and tetragonal phases was identified in the composition range of 0.004 < x < 0.006. The ceramics near the morphotropic phase boundary exhibit a strong compositional dependence and enhanced piezoelectric properties. The ceramics with 0.6 mol.% BiFeO₃ exhibit good electrical properties (d₃₃ ∼ 246 pC/N, k_p ∼ 43%, T_c ∼ 285 °C, ?_r ∼ 1871, and tan δ ∼ 1.96%). These results show that the (1 − x) (K_0.44Na_0.52Li_0.04)(Nb_0.84Ta_0.1Sb_0.06)O₃ − x BiFeO₃ ceramic is a promising lead-free piezoelectric material for applications in different devices.     

Study on properties of BaxSmyTi7O20 ceramics with CaO-SiO2-B2O3 glass

The effect of CaO-SiO₂-B₂O₃ (CSB) glass addition on the sintering temperature and dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics has been investigated using X-ray diffraction, scanning electron microscopy and differential thermal analysis. The CSB glass starts to melt at about 970 °C, and a small amount of CSB glass addition to Ba_xSm_yTi₇O₂₀ ceramics can greatly decrease the sintering temperature from about 1350 to about 1260 °C, which is attributed to the formation of liquid phase. It is found that the dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics are dependent on the amount of CSB glass and the microstructures of sintered samples. The product with 5 wt% CSB glass sintered at 1260 °C is optimal in these samples based on the microstructure and the properties of sintering product, when the major phases of this material are BaSm₂Ti₄O₁₂ and BaTi₄O₉. The material possesses excellent dielectric properties: ?_r = 61, tan δ = 1.5 × 10⁻⁴ at 10 GHz, temperature coefficient of dielectric constant is −75 × 10⁻⁶ °C⁻¹.     

Crystal structure and microwave dielectric properties of (1 − x)NdAlO3-xCaTiO3 ceramics

Crystal structure and microwave dielectric properties of (1−x)NdAlO₃-xCaTiO₃ ceramics have been investigated. Crystal structure of the specimens changed with the composition. Rhombohedral structure was found for the specimens with x≤0.1. When 0.3≤x≤0.7, the specimens had the tetragonal structure and it changed to the orthorhombic structure as x exceeded 0.7. Two types of the second phases were observed in (1−x)NdAlO₃-xCaTiO₃ ceramics. For the specimens with x≤0.5, Nd₄Al₂O₉ phase was observed and Al-rich phase was found in the specimens with x≥0.7. The dielectric constant (ε_r) and the temperature coefficient of the resonant frequency (τ_f) increased with the increase of x. The Q×f value of the specimen increased with x and exhibited the maximum value when x=0.5. The microwave dielectric properties of Q×f=45,000 GHz, ε_r=45 and τ_f=−1.5 ppm/°C were obtained for 0.3NdAlO₃-0.7CaTiO₃ ceramics.     

Synthesis and characterisation of the double perovskite Ba2(Zn0.5Ti0.5X)O6 (X = Nb, Ta) ceramics

Ba₂(Zn_0.5Ti_0.5X)O₆ compounds from the general ABO₃ perovskite family were synthesized by the classical solid-state route for X = Nb and Ta with various A/B ratios (1.005, 1 and 0.995). After the calcination step at 1100 °C, both compounds (X = Nb and Ta) contain mainly the cubic disordered ‘Ba₂(Zn_0.5Ti_0.5X)O₆’ phase but traces of BaTiO₃ and secondary phases are often detectable. Nevertheless, after the sintering stage at higher temperature (from 1300 to 1500 °C) and for all A/B ratios investigated, Ti enters into the cubic perovskite structure, resulting in the formation of a unique ‘Ba₂(Zn_0.5Ti_0.5X)O₆’ phase. Attractive dielectric properties have been measured on the tantalum-based compound for A/B = 0.995 (Q ∼2000 at 7.4 GHz and ? = 39.6) as well as on the niobium-based phase for A/B = 1.005 (Q ∼2200 at 6.1 GHz and ? = 54.8). All these characteristics were confirmed at 1 MHz and a linear dependence of the permittivity versus temperature from −60 to 180 °C has also been evidenced for both formulations. Sinterability, dielectric properties and microstructure of such compounds are discussed with respect to the stoichiometry.