Li0.5La0.5TiO3包覆LiNil/3Co1/3Mnl/3O2材料的研究

以Li0.5La0.5TiO3为包覆物,制备了固体电解质包覆的LiNil/3Co1/3Mnl/3O2正极材料。采用XRD、SEM对材料进行了表征:XRD显示未包覆的材料具有α-NaFeO2层状结构,粒径在200～300nm之间,包覆后材料粒径略有增大,包覆层具有ABO3型固体电解质结构。包覆层的致密程度及材料的循环稳定性与热处理温度有关。包覆后400℃热处理得到的材料首次放电比容量为185mAh/g,较未包覆材料容量有所提高,50次循环后其容量仍能达到156.5mAh/g,表明包覆物Li0.5La0.5TiO3对LiNil/3Co1/3Mnl/3O2具有保护作用。     

La0.5Y0.5Ni4.8Mn0.1Al0.1和La0.5Y0.5Ni4.8Al0.2合金的储氢性能研究

针对两种新型稀土型储氢合金La0.5Y0.5Ni4.8Mn0.1Al0.1和La0.5Y0.5Ni4.8Al0.2的储氢特性进行研究分析。实验表明,相同温度下,La0.5Y0.5Ni4.8Mn0.1Al0.1和La0.5Y0.5Ni4.8Al0.2合金的PCT曲线基本重合,且都具有优良的吸氢动力学性能;相比之下,后者的滞后系数要小于前者,吸氢量较大,吸氢速率也较快,故其储氢性能较优。300次吸放氢循环实验结果表明,La0.5Y0.5Ni4.8Al0.2合金的吸氢动力学性能虽然略有下降,但抗粉化性能较好。     

MgO-Al2O3-SiO2-TiO2-Y2O3玻璃的弹性模量

根据硬盘基板用材料的要求，制备了MgO-Al2O3-SiO2-TiO2-Y2O3高弹性模量玻璃（120GPa)，玻璃的弹性模量随组成的变化服从Makishima-Mackenzie理论，MgO,Al2O3,TiO2,Y2O3等具有较高单位体积离解能的氧化物有利于提高玻璃的弹性模量，但玻璃弹性模量的理论计算值低于测试值，这是因为Makishima-Mackenzie理论没有考虑玻璃内阳离子的具体配位，对MgO,Y2O3堆积密度因子的堆导存在误差，因此利用Makishima-Mackenzie理论发展高弹性模量玻璃时应对MgO,Y2O3等氧化物的计算进行修正。     

La2O3添加对MgAl2O4-CaAl4O7-CaAl12O19复合材料烧结行为的影响

为适应材料轻量化的发展需要,在1 400~1 600℃温度下开发了MgAl₂O₄-CaAl₄O₇-CaAl₁₂O₁₉（MA-CA₂-CA₆）复合材料,并考察了La₂O₃添加对该复合材料烧结行为、显微结构和力学性能的影响。结果表明,La₂O₃添加剂优先固溶到MA-CA₂-CA₆复合材料组成晶相CA₆中,促使CA₆相发生晶格畸变,有效抑制了CA₆晶粒沿基面的异常长大,其形貌由片状向等轴状趋势转变,促使MA-CA₂-CA₆复合材料制备过程中由于CA₆晶粒异常长大而导致的多孔网状显微结构得以有效消除,因此也极大地改善了Mg²⁺的扩散条件,在一定程度上间接促进了MA晶粒的发育,有效促进了MA-CA₂-CA₆复合材料的烧结。经1 200℃预烧、1 600℃保温2 h烧成后,当La₂O₃的添加量为4wt%时,MA-CA₂-CA₆复合材料试样的显气孔率由19.2%下降至6.1%,体积密度由2.78 g/cm³上升至3.18 g/cm³,制得了MA、CA₂、CA₆晶相呈现交织分布、显微结构致密、有利于其力学性能改善的La₂O₃/MA-CA₂-CA₆复合材料,经1 200℃预烧、-1 600℃保温2 h烧成后的4wt% La₂O₃添加试样,其冷态抗压强度由317 MPa增加到了501 MPa。     

MoO3-V2O5-P2O5-Fe2O3玻璃的制备及性能研究

制备了MoO3-V2O5-P2O5-Fe2O3系磷酸盐玻璃,研究了玻璃形成能力、热膨胀系数和抗潮解等性能.结果表明,MoO3-V2O5-P2O5-Fe2O3系统具有较宽的玻璃形成区和较强的玻璃形成能力,当MoO3/V2O5≈1.5时,玻璃形成能力最强.MoO3-V2O5-P2O5-Fe2O3玻璃的热膨胀系数约为60～110×10-7/℃,并且随着Fe2O3含量的增加而逐渐增大.加入适量的Fe2O3能够显著改善MoO3-V2O5-P2O5玻璃的抗潮解性能,在90℃的去离子水中的溶解速率达到8.0×10-9g·cm-2·min-1.     

Na0.5Bi2.5Nb2O9-Na0.5Bi4.5Ti4O15材料的微观结构及电性能

采用固相烧结法制备了铋层结构铁电材料(1-x)Na0.5Bi2.5Nb₂O₉-xNa0.5Bi4.5Ti₄O₁₅(NBNO-NBT-x)。结合XRD、SEM以及电子能谱分析推测NBNO-NBT-0.5陶瓷主要为2-4层的共生结构NaBi₇Ti₄Nb₂O₂₄,由Na0.5Bi2.5Nb₂O₉和Na0.5Bi4.5-Ti₄O₁₅沿c轴交替排列。晶格结构的不对称性增加导致晶格应力增大,而NBNO和NBT两种单体系的复合将进一步加大离子无序和结构无序,从而使该组成的陶瓷表现出不同于两种单体系的微观结构和电性能。NBNO-NBT-0.5陶瓷的晶粒长度大于20 μm,厚度小于2 μm,晶粒长径比明显高于NBNO和NBT;而相比于两种单体其居里温度TC降低,居里峰宽化,高温介电损耗增大,电导激活能减小,铁电、压电性能降低。     

Sc2O3-Y2O3-ZrO2陶瓷材料热物理性能

采用固相合成法制备了6.3%Sc_2O_3-1.3%Y2O3-92.4%ZrO_2(摩尔分数)陶瓷材料。分别利用X射线衍射、示差扫描量热法、高温热膨胀仪和激光导热法对陶瓷材料的物相组成、高温相稳定性、热膨胀系数和热扩散等性能进行了表征。结果表明,经1600℃烧结6h,该陶瓷材料由单一的立方相结构组成,具有良好的高温相稳定性,热导率低于传统的6~8YSZ,是一种良好的热障涂层候选材料。     

Li2O/K2O物质的量比对P2O5-Al2O3-BaO-Li2O-K2O磷酸盐玻璃热光性能的影响

通过高温熔融法制备了不同Li_2O/K_2O物质的量比的磷酸盐玻璃,研究了其热学性能和热光性能。采用干涉仪法测试了玻璃的折射率温度系数dn/dT,并进一步计算获得了热光系数。结果表明:随着Li_2O/K_2O物质的量比的增大,玻璃的转变温度Tg、软化温度Tf、热膨胀系数α皆出现极值点,呈现明显的混合碱效应;而玻璃的热光系数dS/dT随着Li_2O含量增加而增大,当Li_2O/K_2O物质的量比为9∶6时,玻璃的dS/dT为0.08×10~(-6)/K;在磷酸盐体系中可获得具有零热畸变的光学玻璃。     

La0.85Sr0.15Cr0.9Ni0.1O3-δCe0.8Sm0.2O1.9作为SOFC阳极材料的研究

较低的催化活性大大地限制了La0．85Sr0．15Cr0．9Ni0．1O3-δ-（LSCN）作为直接碳氢化合物燃料SOFC阳极材料的应用．本文尝试用Pechini法合成LSCN，并按重量比1：1向其中加入纳米Ce0.8Sm0.2O1.9（SDC）作为阳极材料．经1500℃高温烧结12h后，LSCN与SDC以及电解质YSZ仍可以保持各自独立的相结构．加入SDC没能提高阳极的电导率，但由于改善了阳极电解质界面的结合状况，扩展了电极反应的活性区域，使阳极材料的极化性能有了提高．显微结构观察品示．LSCN-SDC阳极存甲烷与氧中使用时没有碳沉积现象．     

La2O3在MgO-Al2O3-SiO2-TiO2微晶玻璃中的作用

在MgO-Al2O3-SiO2-TiO2玻璃中添加不同数量的氧化镧，采用差热分析，X射线衍射及电子显微镜等技术研究了氧化镧对玻璃析晶过程与力学性能的影响。氧化镧的加入使玻璃中析出α－堇青石相的温度降低，同时避免了高膨胀方石英相的析出。随着氧化镧加入量的增加，玻璃整体析晶能力下降，微晶玻璃中晶相含量减少，晶粒尺寸增大，微晶玻璃的弹性模量与硬度减小，断裂韧性增加，体现出大尺寸长柱状金红石晶粒的增韧作用。     

Magnetic coupling in La0.67Ca0.33MnO3/La0.67Sr0.33CoO3/La0.67Ca0.33MnO3 sandwiches

La_0.67Ca_0.33MnO₃ (LCMO)/La_0.67Sr_0.33CoO₃ (LSCO)/LCMO trilayer films are fabricated on single-crystal substrates NdGaO₃ (110) and the interlayer coupling are investigated. Compared with LCMO single layer, sandwiches showed the enhanced metal-insulator transition temperature of LCMO layers. The magnetoresistance is dependent on spacer thickness and the peak value dramatically decreases when LSCO layer is thick enough because of shorting by the LSCO layer. The magnetic coercivity H_C shows a nonmonotonic behavior with changing spacer layer thickness and the waist-like hysteresis indicates that there is an indirect exchange coupling between the top and bottom LCMO layers across the spacer layer.     

Varistor properties of ZnO-Pr6O11-CoO-Cr2O3-Y2O3-In2O3 ceramics

The varistor properties of the ZnO-Pr₆O₁₁-CoO-Cr₂O₃-Y₂O₃-In₂O₃ ceramics were investigated for different concentrations of In₂O₃. The increase of In₂O₃ concentration slightly increased the sintered density (5.60-5.63 g/cm³) and slightly decreased the average grain size (3.4-2.9 μm). The breakdown field increased from 6023 to 14822 V/cm with increasing concentration of In₂O₃. The nonlinear coefficient increased from 17.6 to 44.6 for up to 0.005 mol%, whereas the further doping caused it to decrease to 36.8. In₂O₃ acted as an acceptor due to the donor concentration, which decreases in the range of 1.02 × 10¹⁷ to 0.24 × 10¹⁷/cm³ with increasing concentration of In₂O₃.     

Microstructures of YBa2Cu3O7/La0.7Ca0.3MnO3 and La0.7Ca0.3MnO3/YBa2Cu3O7 bi-layers grown on (001)LaAlO3

Epitaxial YBa₂Cu₃O₇/La_0.7Ca_0.3MnO₃ (YBCO/LCMO) bi-layers and La_0.7Ca_0.3MnO₃/YBa₂Cu₃O₇ (LCMO/YBCO) bi-layers were grown on (001)LaAlO₃ by pulsed laser deposition, and their microstructures were compared by transmission electron microscopy investigation. In the YBCO(100 nm)/LCMO(150 nm) bi-layers, the LCMO layer consists of columnar grains of ~ 17 nm in diameter and contains mixed orientation domains of [100]_c, [010]_c and [001]_c. The YBCO layer is totally c-axis oriented and the YBCO lattices are tilted − 2.5° to + 2.5° as they grew on the rough surfaces of LCMO columnar grains. For the LCMO(140 nm)/YBCO(140 nm) bi-layers, the LCMO/YBCO interface is sharp and flat. The initial 12-nm thickness of the YBCO layer is composed of c-axis oriented domains, and the upper part of YBCO layer is [100] oriented. The LCMO layer was predominantly [001]_c oriented while [100]_c-oriented domains were occasionally observed.     

PbSbBiS4-Sb2S3 and PbSbBiS4-Bi2S3 joins in the PbS-Sb2S3-Bi2S3 system

Phase equilibria along the PbSbBiS₄-Sb₂S₃ and PbSbBiS₄-Bi₂S₃ joins of the PbS-Sb₂S₃-Bi₂S₃ system have been studied for the first time using differential thermal analysis, X-ray diffraction, microstructural analysis, microhardness tests, and density measurements, and the phase diagrams of the joins have been mapped out. The joins are shown to be pseudobinary with limited series of terminal solid solutions. The solid solutions are p-type semiconductors.     

Structural study of Sr0.3Ba0.7Nb2O6 and La0.030Sr0.255Ba0.700Nb2O6 ceramic systems

Sr_0.3Ba_0.7Nb₂O₆ (SBN) and La_0.030Sr_0.255Ba_0.700Nb₂O₆ (LSBN) ceramic compounds have been prepared using the traditional ceramic method at two different calcination temperatures (900 and 1000 °C) and later sintered both at 1400 °C. A study of the effects of the calcination temperatures and La substitution on the morphological, compositional, and structural properties of SBN and LSBN is presented using scanning electronic microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) analysis. From Rietveld refinement processes, the XRD patterns were interpreted to evaluate such effects in the structural parameters and the site occupation factors of the heavy metals and oxygen atoms. The effect of the incorporation of La resulted in a 0.25% cell contraction and turned out to be higher than the 0.08% dilation effect produced by the increase of calcination temperature. The La ion with similar effective ionic radius and higher electronegativity is incorporated into the structure occupying the A₁ site just like the Sr ions in the SBN compound. Differences in the site occupation factors between the SBN and LSBN samples lead to substantial changes in the physical properties such as temperature of relative dielectric constant maximum, relative dielectric constant, and dielectric loss, correlated with the distortion and the relative orientation of the oxygen octahedra.     

Nanocrystallization of SrBi2Nb2O9 from glasses in the system Li2B4O7---SrO---Bi2O3---Nb2O5

Transparent glasses in the system (100−x)Li₂B₄O₇–x(SrO---Bi₂O₃---Nb₂O₅) (10≤x≤60) (in molar ratio) were fabricated by a conventional melt-quenching technique. Amorphous and glassy characteristics of the as-quenched samples were established via X-ray powder diffraction (XRD) and differential thermal analyses (DTA) respectively. Glass–ceramics embedded with strontium bismuth niobate, SrBi₂Nb₂O₉ (SBN) nanocrystals were produced by heat-treating the as-quenched glasses at temperatures higher than 500 °C. Perovskite SBN phase formation through an intermediate fluorite phase in the glass matrix was confirmed by XRD and transmission electron microscopy (TEM). Infrared and Raman spectroscopic studies corroborate the observation of fluorite phase formation. The dielectric constant (_r) and the loss factor (D) for the lithium borate, Li₂B₄O₇ (LBO) glass comprising randomly oriented SBN nanocrystals were determined and compared with those predicted based on the various dielectric mixture rule formalism. The dielectric constant was found to increase with increasing SBN content in LBO glass matrix.     

Syntheses of hollandite type Rb2Cr8O16, K2Cr2V6O16 and K2V8O16

Hollandite-type compounds, Rb₂Cr₈O₁₆, K₂Cr₂V₆O₁₆ and K₂V₈O₁₆, were synthesized under high P-T conditions up to 1200°C and 7GPa. The structural refinement using a single crystal of Rb₂Cr₈O₁₆ confirms that the structure is similar to that of K₂Cr₈O₁₆. Magnetic measurements indicate that Rb₂Cr₈O₁₆ is ferromagnetic below 295K, K₂Cr₂V₆O₁₆ paramagnetic down to 77K and K₂V₈O₁₆ has susceptibility anomaly at 175K. These compounds are all semiconductive and show discontinuities in temperature-resistivity curves at points corresponding to magnetic anomalies.     

Vapour-liquid equilibria in the ternary mixtures N2---CH4---C2H6 and N2---C2H6---C3H8

A systematic study was performed with mixtures consisting of N₂, CH₄, C₂H₆ and C₃H₈, to investigate experimentally phase equilibria and caloric properties and to test the accuracy of thermodynamic correlations. The first part of this Paper reports results of T---p---x---y measurements on ternary systems in the range 20 < p < 120 bar and 140 < T < 220 K. The results are compared with data calculated by generalized equations of state.     

The effect of Bi1.5Zn0.5Nb0.5Ti1.5O7 cover layer on the dielectric and tunable properties of Ba0.6Sr0.4TiO3/Bi1.5Zn0.5Nb0.5Ti1.5O7 bilayered thin films

Bi_1.5Zn_0.5Nb_0.5Ti_1.5O₇ (BZNT) thin films with different thicknesses as cover layers were deposited on the Ba_0.6Sr_0.4TiO₃ (BST) thin films on the Pt/Ti/SiO₂/Si substrates by radio frequency magnetron sputtering method. The microstructure, surface morphology, dielectric and tunable properties of BST/BZNT heterogeneous bilayered films were investigated as a function of the thickness of BZNT films and the effect of BZNT films on the asymmetric electrical properties of BST/BZNT bilayered films was discussed. It was found that BZNT cover layer significantly improved the leakage current and the dielectric loss, and the dielectric constant and tunability of BST/BZNT bilayered thin films simultaneously decreased with the increasing thickness of BZNT films. The BST/BZNT bilayered thin film with a 50 nm BZNT cover layer gave the largest figure of merit (FOM) of 33.48 with the upper tunability of 55.38%. The asymmetric electrical behavior of BST/BZNT bilayered films is probably related to an internal electric field caused by built-in voltages at Pt/BST and BZNT/Au interfaces.     

静电纺丝法制备的Co0.6Ni0.3Cu0.1Fe2O4和Co0.6Ni0.3Zn0.1Fe2O4纳米纤维的结构及磁性能

采用静电纺丝技术制备出表面光滑、直径均匀的Co_(0.6)Ni_(0.3)Cu_(0.1)Fe_2O_4/PVP和Co_(0.6)Ni_(0.3)Zn_(0.1)Fe_2O_4/PVP纳米纤维前驱丝,经500~900℃煅烧后得到Co_(0.6)Ni_(0.3)Cu_(0.1)Fe_2O_4和Co_(0.6)Ni_(0.3)Zn_(0.1)Fe_2O_4纳米纤维。用TG-DSC、XRD、SEM及VSM现代测试分析手段对Co_(0.6)Ni_(0.3)Cu_(0.1)Fe_2O_4和Co_(0.6)Ni_(0.3)Zn_(0.1)Fe_2O_4纳米纤维的结构、形貌及磁学性能进行测试表征。结果表明:在空气气氛中经500~900℃煅烧后可得到纯尖晶石相、结晶度良好的纳米纤维或短纤维;当温度为700℃时,Co_(0.6)Ni_(0.3)Cu_(0.1)Fe_2O_4和Co_(0.6)Ni_(0.3)Zn_(0.1)Fe_2O_4纳米纤维的形貌细长而光滑且直径相对均匀,大约为80nm;此时Co_(0.6)Ni_(0.3)Cu_(0.1)Fe_2O_4纳米纤维则保有较高的剩磁比(M_r/M_s)及矫顽力,分别为0.56和1 088.87Oe。在500℃、600℃、700℃、800℃、900℃煅烧后,Co_(0.6)Ni_(0.3)Zn_(0.1)Fe_2O_4纳米纤维的饱和磁化强度分别比Co_(0.6)Ni_(0.3)Cu_(0.1)Fe_2O_4纳米纤维增大了14.5%、7%、16%、10.7%、8%,而矫顽力则分别降低了38%、51%、50%、46%、46.7%。两种纳米纤维的饱和磁化强度及矫顽力存在差异,为CoNi铁氧体在电磁方面的应用提供了很好的参考。