Nd3+A位置换对(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3陶瓷微波介电性能的影响

研究了Nd3+离子A位置换改性(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3陶瓷的微波介电性能.[(Pb0.5Ca0.5)1-xNdx](Fe0.5Nb0.5)O3(PCNFN)陶瓷的微波介电性能得到改善是由于少量过剩的Nd3+与(Pb,Ca)2+的固溶能够消除氧空位.当x=0.02时,能够形成单相的钙钛矿相,随着Nd3+置换量的增加,过剩的Nd3+将导致第二相焦绿石的形成,焦绿石会恶化PCNFN的微波介电性能.PCNFN介电性能随x的增加而下降是由于焦绿石相随x增加的结果.当x=0.02-0.05,PCNFN陶瓷有很好的微波介电性能,介电常数K>100,Qf值为5385-5797GHz,频率温度系数TCF随Nd3+含量的增加从正的变为负的.     

Mg4Nb2O9/CaTiO3复合陶瓷的微波介电性能

采用传统固相法制备Mg4Nb2O9/CaTiO3复合陶瓷,研究Li2CO3-V2O5(LV)共掺杂对其烧结特性、微观结构和微波介电性能的影响.实验结果表明:一定量的LV掺杂能够使Mg4Nb2O9/CaTiO3复合陶瓷的烧结温度降至1200℃;XRD和EDX综合分析表明,样品由(Mg4-xCax)Nb2O9/(Ca1-x...     

Microwave dielectric properties of (A2+(1/3)B5+(2/3))0.5Ti0(0.5)O2 (A2+ = Zn, Mg, B5+ = Nb, Ta) ceramics

Dielectric properties of (A(2+)(1/3)B(5+)(2/3))(0.5)Ti0(0.5)O(2) (A(2+) = Zn, Mg, B(5+) = Nb, Ta) ceramics were investigated at microwave frequencies. A single phase with tetragonal rutile structure was obtained through the entire compositions. Dielectric properties were strongly dependent on the structural characteristics. The specimens with B(5+) = Nb showed a larger dielectric constant than those with B(5+) = Ta due to the decrease of bond valence. Quality factors (Qf) of the specimens with B(5+) = Ta were larger than those with B(5+) = Nb. Temperature coefficient of the resonant frequencies (TCF) of (Zn(1/3)Nb(2/3) )0(0.5)Ti0(0.5)O(2) was larger than that of (Mg(1/3)Ta(2/3))0(0.5)Ti0(0.5)O(2). These results could be attributed to the changes of the temperature coefficient of dielectric constant and the degree of oxygen octahedral distortion.     

SnO2掺杂对BMN陶瓷结构及介电性能的影响

采用固相烧结法制备Ba(Mg_(1/3)Nb_(2/3))O_3+x(x=0~8)%SnO_2(BMSN,x为质量分数)微波介质陶瓷,并研究SnO_2掺杂对Ba(Mg_(1/3)Nb_(2/3))O_3(BMN)微波介质陶瓷结构及介电性能的影响。XRD分析表明,陶瓷体系中存在两种相,主晶相Ba(Mg_(1/3)-Nb_(2/3))O_3和附加相Ba_5Nb_4O_(15)。随着x的增大,BMSN陶瓷体系的相结构逐渐由钙钛矿六方结构转变为立方结构,同时有序相逐渐由1∶2有序结构转变为1∶1有序结构。研究表明:添加适量的SnO_2可以促进液相烧结,当SnO_2掺杂质量分数为6%时,BMN陶瓷致密化烧结温度由纯相时的1 550℃以上降低至1 200℃,表观密度ρ=6.39g/cm3,相对理论密度为99.1%,此时BMSN陶瓷体系拥有优良的微波介电性能——高相对介电常数(ε_r=33.6),接近于零的谐振频率温度系数(τ_f=0.15×10~(-6)℃~(-1)),高品质因数与谐振频率的乘积(Q·f=112 300GHz(8GHz))。     

Microwave dielectric characteristics of Ba(Mg1/3Ta2/3)O3 ceramics sintered at low-temperatures

The microwave dielectric properties and microstructures of Ba(Mg_1/3Ta_2/3)O₃ (BMT) ceramics sintered at low temperatures with 2–3 wt.% NaF additives were investigated. BMT ceramics sintered at 1340 °C for 3–12 h showed dielectric constants (_r) of 25.5–25.7, Qf values of 41 500–50 400 GHz and temperature coefficients of the resonator frequency (τ_f) of 10.9–21.4 ppm °C⁻¹. The variation of sintering time almost had no effect on the dielectric constant. The Qf value increased and the τ_f decreased with increasing sintering time. The ordering degree of Mg²⁺ and Ta⁵⁺ at B-sites increased with increasing sintering time.     

微波电介质陶瓷的制取与研究

以（Mg0.8Zn0.2）TiO,（MZT）为原料,采用加入高电介质材料Ba4Nd28/3T18O54zBi2O3（BNT）制备微波电介质陶瓷0．7（Mg08Zn02）T103·0．3{Ba4Nd2Ⅳ3Ti18054·zBi203I（z=0．15,0．18,0．2）,以提高MZT的介电性能。掺入Bi3＋可以降低烧结温度,从而可以在低烧结温度（（1200-1230％）下制取MZT和BNT的合成材料。通过对介电性能、密度、XRD和SEM测试所获得的陶瓷可以发现,掺入Bi3＋数量的多少和结烧温度的高低会影响到陶瓷的结构和性能,结果说明,当z=0．18,0．7（Mgn8znn2）Ti03·0．3{Ba4NdzsnTil8054·zBi203}的结烧温度为1230℃时,可以获得很好的介电性能：εr=35．56,Qf=5811GHz,TF=-3．225ppm／℃。     

Nd3+A位置换对(Pb0.5Ca0.5)(Fe0.5Nb0.5)O3陶瓷微波介电性能的影响

研究了Nd³⁺离子A位置换改性(Pb_0.5Ca_0.5)(Fe_0.5Nb_0.5)O₃陶瓷的微波介电性能.[(Pb_0.5Ca_0.5)_1-xNd_x](Fe_0.5Nb_0.5)O₃(PCNFN)陶瓷的微波介电性能得到改善是由于少量过剩的Nd³⁺与(Pb,Ca)²⁺的固溶能够消除氧空位.当x=0.02时,能够形成单相的钙钛矿相,随着Nd³⁺置换量的增加,过剩的Nd³⁺将导致第二相焦绿石的形成,焦绿石会恶化PCNFN的微波介电性能.PCNFN介电性能随x的增加而下降是由于焦绿石相随x增加的结果.当x=0.02-0.05,PCNFN陶瓷有很好的微波介电性能,介电常数K>100,Qf值为5385-5797GHz,频率温度系数TCF随Nd³⁺含量的增加从正的变为负的.     

Ca0.3(Li1/2Sm1/2)0.7TiO3微波介质陶瓷的低温烧结研究

采用传统陶瓷制备工艺, 制备了掺杂Na₂O-CaO-B₂O₃(NCB)氧化物的Ca_0.3(Li_1/2Sm_1/2)_0.7TiO₃(CLST)陶瓷, 研究了NCB掺杂量与晶相组成、显微结构、烧结性能及微波介电性能的关系. 研究结果表明: 复合氧化物NCB掺杂量在1wt%～15wt%范围内没有杂相生成, 晶相仍呈斜方钙钛矿结构. 随着NCB添加量的增加, 陶瓷致密化温度和饱和体积密度降低, 介电常数ε_r、无载品质因数与谐振频率乘积Qf值也呈下降趋势, 频率温度系数τ_f向正方向增大. NCB氧化物掺杂能有效地将CLST陶瓷的烧结温度由1300℃降低至900℃. 添加12.5wt% NCB的CLST陶瓷在低温900℃烧结5h仍具有良好的微波介电性能: ε_r=73.7, Qf=1583GHz, τ_f=140.1×10-6/℃, 满足高介多层微波器件的设计要求.     

(Mg1-xSrx)2Al4Si5O18陶瓷的显微结构与微波介电性能研究

采用固相烧结反应法制备(Mg1-xSrx)2Al4Si5O18陶瓷.Sr掺杂促进低温相β-Mg2Al4Si5O18向高温相α-Mg2Al4Si5O18转变,并拓宽了(Mg1-xSrx)2Al4Si5O18陶瓷的致密化烧结温度范围.X射线衍射结果表明在0≤x<0.2范围内,(Mg1-xSrx)2Al4Si5O18陶瓷以(Mg,Sr)2Al4Si5O18堇青石固溶体形式存在;在0.6相似文献   

Dielectric properties of rutile structure (Zn₁/₃B₂/₃)x(TiySn(1-y))(1-x)O₂ (B=Nb⁵+,Ta⁵+) at microwave frequencies

The microwave dielectric properties of rutile (Zn?/? B?/?)x(TiySn(1-y))(1-x)O? (B=Nb?+,Ta?+, 0.05 ≤ x ≤ 0.35, y = 0.2, 0.8) were investigated with structural characteristics. A single phase with tetragonal rutile (P4?/mnm, no. 136, Z = 2) structure was obtained through the entire range of compositions. With an increase of (Zn?/?B?/?)O? content, the dielectric constant (K) of sintered specimens with (Ti?.?Sn?.?)O? increased, whereas that of the specimens with (Ti?.?Sn?.?)O? decreased. The temperature coefficient of resonant frequency (TCF) of sintered specimens was dependent upon oxygen octahedral distortion and/or cations bond valence of the rutile structure. The quality factor (Qf) was dependent upon (Zn?/?B?/?)O? content, and the specimens with (Ti?.?Sn?.?)O? showed larger Qf values than those with (Ti?.?Sn?.?)O? for the same content of (Zn?/?B?/?)O?.     

La2O3掺杂BST/Mg2TiO4微波复合陶瓷的制备和性能

用固相烧结法制备掺杂La2O3的Ba0.55Sr0.45TiO3/Mg2TiO4微波复合陶瓷,研究了掺杂对其微观结构、微波(f=10 GHz)介电性能和调谐率的影响.结果表明:当掺杂La2O3量(质量分数)为1.2%时,La3+进入BST晶格,且抑制了BST/Mg2TiO4中Ti从+4向+3价转化;La2O3的掺入比较...     

(Ba1-xSrx)La4Ti4O15（x=0.8～0.95）陶瓷的微结构及微波介电性能研究

采用固相反应法制备了(Ba1-xSrx)La4Ti4O15(x=0.8~0.95)复合体系微波介质陶瓷,并对其进行物相组成、晶体结构分析以及微波介电性能的研究.研究结果表明,(Ba1-xSrx)La4Ti4O15陶瓷主晶相为SrLa4Ti4O15,并伴随有第二相SrLa8Ti9O15.SEM观察表明,Ba0.2Sr0.8La4Ti4O15陶瓷内部微观结构致密,晶粒尺寸在10~20μm之间,晶界清晰.随着x值逐渐增大,(Ba1-xSrx)La4Ti4O15陶瓷中晶粒形态发生变化,气孔增多.在x=0.8时,(Ba1-xSrx)La4Ti4O15陶瓷具有优良的微波介电性能,即εr=40.86,Q×f≈62806 GHz,τf=20×10 6/℃.随着Ba2+的含量逐渐增加,该陶瓷的介电常数εr单调上升,品质因子Q×f值增加,说明适量的Ba2+替代Sr2+能改善陶瓷的微波介电性能.     

Effect of B2O3 additive on the sintering temperature and microwave dielectric properties of Ba(Mg1/3Ta2/3)O3 ceramics

Journal of Materials Science: Materials in Electronics - This paper reported a research of the sinterability, microstructures, and microwave dielectric properties of Ba(Mg1/3Ta2/3)O3 (BMT) ceramics...     

Formation and microwave dielectric properties of Sr(Ga0.5Ta0.5)O3-based complex perovskites

The Sr(Ga0.5Ta0.5)O3-based perovskites with O2- and/or Sr2+ vacancies were formed by changing the A-site and/or B-site cation ratios. The Sr-deficient perovskites with a limited composition of Sr0.86(Ga0.36Ta0.64)O3 could be obtained, whereas oxygen vacancies were hardly created. The B′-site Ga3+ cation could be replaced with large Sc3+, In3+, Y3+, Nd3+ and La3+. The crystal symmetry of the complex perovskites changed from cubic (B′=Ga3+, Sc3+, In3+) to tetragonal (B′=La3+) through rhombohedral (B′=Y3+, Nd3+). The dielectric permittivities of these ceramics indicated no distinct dependence on the B′-site cation species. The temperature coefficient of permittivity might be associated with the symmetry change of the perovskite phases. Higher microwave Qf values, >Qf=38 000 GHz, were obtained for our complex perovskite ceramics, except with B′=La3+. This revised version was published online in July 2006 with corrections to the Cover Date.     

掺钾对PMN基陶瓷有序微区及介电和电致伸缩性能的影响

使用二次合成法制备了不同钾含量的0.80Pb(Mg1/3Nb2/3)O3-0.20PbTiO3陶瓷，首先研究了掺钾对PMN基预烧粉体和陶瓷试样相组成的影响，在此基础上详细研究了掺钾对PMN基陶瓷有序微区、介电和电致伸缩性能的影响规律。掺钾对PMN基预烧粉体和陶瓷的相组成影响很小；理论计算和Raman散射光谱分析都表明掺钾使PMN基陶瓷的有序微区的尺寸稍微减小；掺钾也小幅度地减小了PMN基陶瓷的介电和电致伸缩性能，最后分析了掺钾降低介电和电致伸缩性能的原因。     

SrTiO_3/CaCu_3Ti_4O_(12)复合陶瓷材料的介电性能

本文采用固相反应法制备了xSrTiO_3/(1-x)CaCu_3Ti_4O_(12)(x=0,0.2,0.4,0.6,0.8,1)复合陶瓷,研究了复合材料的物相、微观结构和宽温度宽频率范围内的介电性能。结果表明:在1348~1600K的温度范围内烧结能够得到致密性良好的xSrTiO_3/(1-x)CaCu_3Ti_4O_(12)(x=0,0.2,0.4,0.6,0.8,1)复合陶瓷。频率为100kHz时,样品的室温介电常数随SrTiO_3含量的增加而减少,从71358(x=0)单调减少至270(x=1),其变化规律遵循Lichtenecker法则。介电损耗随SrTiO_3含量的增加先增大后减少。当x=0.2时,样品与CaCu_3Ti_4O_(12)陶瓷的介电性能相似,存在低温的介电弛豫和巨介电常数平台。随着SrTiO_3含量的增加,复合陶瓷的低温介电弛豫激活能增大,介电响应被抑制,而高温介电响应由于高温电导的影响而增强,使得CaCu_3Ti_4O_(12)特有的巨介电常数平台随着SrTiO_3的增加逐渐消失,xSrTiO_3/(1-x)CaCu_3Ti_4O_(12)复合材料的温度依赖性增强。     

Dielectric Properties of Ba0.6Sr0.4TiO3-La(B0.5Ti0.5)O3 (B=Mg, Zn) Ceramics

Ba_0.6Sr_0.4TiO₃-La(B_0.5Ti_0.5)O₃ (B = Mg, Zn) ceramics were prepared by a solid-state reaction method, and their microwave dielectric characteristics and tunability were investigated. The ferroelectric-dielectric solid solutions with cubic perovskite structures were obtained for compositions of 10 to 60 mol% La(Mg_0.5Ti_0.5)O₃ and 10 to 50 mol% La(Zn_0.5Ti_0.5)O₃. With the increase of linear oxide dielectric content, the dielectric constant and tunability were decreased and Qf was increased. Ba_0.6Sr_0.4TiO₃-La(Mg_0.5Ti_0.5)O₃ has better dielectric properties than Ba_0.6Sr_0.4TiO₃-La(Zn_0.5Ti_0.5)O₃. 0.9Ba_0.6Sr_0.4TiO₃-0.1La(Mg_0.5Ti_0.5)O₃ has a dielectric constant ε = 338.2, Qf = 979 GHz and a tunability of was 3.7% at 100 kHz under 1.67 kV/mm. The Qf value of 0.5Ba_0.6Sr_0.4TiO₃- 0.5La(Mg_0.5Ti_0.5)O₃ reached 9367 GHz, but the tunable properties were lost.     

BaTiO3-ZnNb2O6陶瓷介电及储能性能研究

采用固相法制备(1-x)BaTiO₃-xZnNb₂O₆ (x=0.5mol%, 1mol%, 1.5mol%, 2mol%, 3mol%, 4mol%) (简称BTZN)陶瓷, 研究了BTZN陶瓷的烧结温度、结构、介电性能和铁电性能。BTZN陶瓷烧结温度随着ZnNb₂O₆含量增加逐渐降低。XRD结果表明当ZnNb₂O₆含量达到3mol%时出现第二相Ba₂Ti₅O₁₂。介电测试结果表明随ZnNb₂O₆含量的增加, BTZN陶瓷介电常数逐渐减小, 而介电常数的频率稳定性逐渐增强。介电温谱表明所有BTZN陶瓷均符合X8R电容器标准。BTZN陶瓷的极化强度值随着ZnNb₂O₆含量的增加逐渐降低。当x=4mol%时, BTZN陶瓷获得240 kV/cm的击穿电场和1.22 J/cm ³的可释放能量密度。     

Ba6-3x(Sm1-yPry)8+2x Ti18O54微波介质陶瓷结构及性能的研究

本文研究了Ｂａ６－３ｘ（Ｓｍ１－ｙＰｒｙ）８＋２ｘＴｉ１８Ｏ５４（ｘ＝０．５,ｙ＝０．０、０．１、０．２）微波介质陶瓷的结构和性能。结果表明,在Ｓｍ－Ｐｒ系中Ｐｒ取代Ｓｍ形成了钨青铜结构的固溶体,随Ｐｒ取代量的增多,晶格常数呈线性增加趋势。最佳烧结温度确定为１４００℃。同时,随Ｐｒ的取代,介电常数得到提高,同时保持了低的损耗,并可以找到ｆ恰为零的最佳成分点。     

钛锡酸锶钡Ba1-xSrxTi0.90Sn0.10O3陶瓷的结构与介电性能

采用传统陶瓷工艺制备了一系列的钛锡酸锶钡Ba1-xSrxTi0.90Sn0.10O3陶瓷.通过X射线衍射分析了样品的相结构,采用扫描电子显微镜描述了样品的形貌.还研究了介电常数和介电损耗随温度和电场的变化.试验结果表明:用传统的固相反应法制备的钛锡酸锶钡陶瓷的相结构为钙钛矿结构.随着烧结温度的提高,介电常数的峰值呈显著增加,介电损耗在铁电区增加但在顺电区没有明显变化.当Sr的掺入量为14%时得到最大的可调率为82.6%.