高铌TiAl合金钎焊接头组织和性能研究（英文）

采用Ti-28Ni(质量分数,%)共晶钎料在1100℃实现了高铌Ti Al合金(Ti-45Al-8.5Nb-(W,B,Y)(at%),TAN)的真空钎焊连接。钎焊接头的典型界面结构为TAN/τ_3-Al_3Ti_2Ni+B2/α_2-Ti_3Al layer/α_2-Ti_3Al+δ-Ti_2Ni/α_2-Ti_3Al layer/τ_3-Al_3Ti_2Ni+B2/TAN。深入研究了保温时间对钎焊接头界面组织和连接性能的影响。结果表明:Ni元素从熔融钎料向TAN母材的扩散决定了界面组织的演化,随着保温时间的延长促进了扩散层的增厚,同时导致钎缝宽度逐渐减小。接头剪切强度测试结果显示,当保温时间为15 min时,获得的最大接头室温剪切强度和高温(600℃)剪切强度分别是248.6和166.4 MPa。接头断口分析表明在剪切试验中裂纹主要沿着连续的金属间化合物层产生和扩展。     

Al_2O_3陶瓷与TiAl合金真空钎焊接头界面组织及性能

采用AgCuTi活性钎料实现了Al_2O_3陶瓷与TiAl合金的钎焊连接,研究了钎焊接头的界面结构及其形成机制,并且分析了不同钎焊参数对接头界面组织和接头力学性能的影响规律。结果表明:Al_2O_3陶瓷与TiAl合金钎焊接头的典型界面组织为:Al_2O_3/Ti_3(Cu,Al)_3O/Ag(s.s)+Cu(s.s)+AlCu_2Ti/AlCu_2Ti+AlCuTi/TiAl。钎焊过程中,TiAl基体向液态钎料中的溶解量决定了钎焊接头界面组织的形成及其演化。随着钎焊温度的升高和保温时间的延长,Al_2O_3陶瓷侧的Ti_3(Cu,Al)_3O反应层增厚,钎缝中弥散分布的团块状AlCu_2Ti化合物逐渐聚集长大。陶瓷侧界面反应层的厚度和钎缝中AlCu_2Ti化合物的形态及分布共同决定着接头的抗剪强度。当钎焊温度为880℃,保温10 min时,接头的抗剪强度最大,达到94 MPa,此时接头的断裂形式呈现沿Al_2O_3陶瓷基体和界面反应层的复合断裂模式。     

TiAl与Ni基合金接触反应钎焊接头界面组织及性能

以Ti为中间层实现了TiAl与Ni基合金的接触反应钎焊。采用扫描电镜和电子探针等手段对钎焊接头的界面结构及生成相进行分析,并对接头剪切强度进行测试。结果表明:当钎焊温度为960℃时,钎缝主要由Tiss和Ti2Ni组成;当钎焊温度从960℃升高到1000℃时,钎缝中生成Ti-Al及Al-Ni-Ti化合物,典型界面结构为:GH99/(Ni,Cr)ss/Ti2Ni+AlNi2Ti+TiNi/Ti3Al+Al3NiTi2/Ti3Al+Al3NiTi2/TiAl;钎焊温度继续升高,Ti3Al和Al3NiTi2变得粗大,导致接头性能下降。当钎焊温度为1000℃,保温10min时,接头剪切强度达到最大值233MPa。随钎焊温度的升高,钎缝厚度先增加后减小。     

TiAl基合金与Ni基合金钎焊连接接头界面组织及性能

采用BNi2钎料实现了TiAl基合金与Ni基高温合金的钎焊。采用扫描电镜、能谱分析和X射线衍射等手段对钎焊接头的界面组织结构及生成相进行分析,并对接头的抗剪强度进行测试。结果表明,钎焊接头的典型界面结构为：GH99/(Ni)ss (γ)+Ni3B+CrB+富Ti-硼化物/TiNi2Al/TiNiAl+Ti3Al/TiAl;随着钎焊温度的升高或保温时间的延长,较多的B和Si元素扩散进入两侧母材,导致钎缝中硼化物数量减少,而TiAl/钎缝界面的TiNi2Al和TiNiAl+Ti3Al金属间化合物层厚度增加;当钎焊温度为1050 ℃,保温时间为5 min时,接头的抗剪强度达到最大为205 MPa,接头主要断裂于TiNiAl金属间化合物层。当钎焊温度升高或保温时间继续延长时,TiNiAl厚度显著增加,导致接头强度下降     

TiAl/Ni基合金反应钎焊接头的微观组织及剪切强度(英文)

以Ti为中间层,对TiAl基金属间化合物与Ni基高温合金进行反应钎焊连接,研究反应钎焊接头的界面微观结构及剪切强度。通过实验发现,熔融中间层与两侧母材反应剧烈,生成连续的界面反应层。典型的界面微观结构为GH99/(Ni,Cr)ss(γ)/TiNi(β2)+TiNi2Al(τ4)+Ti2Ni(δ)/δ+Ti3Al(α2)+Al3NiTi2(τ3)/α2+τ3/TiAl。当钎焊温度为1000°C,保温时间10min时,所得接头的剪切强度最高为258MPa。进一步升高钎焊温度或延长保温时间,会引起钎缝组织中组成相粗化和脆性金属间化合物层的生成,从而导致接头剪切强度的降低。     

高铌TiAl合金钎焊接头组织和性能研究

采用Ti-28Ni(wt.%)共晶钎料在1100℃实现了高铌TiAl合金(Ti-45Al-8.5Nb-(W, B, Y) (at.%), 简称TAN)的真空钎焊连接。钎焊接头的典型界面结构为TAN/τ3-Al3Ti2Ni + B2/α2-Ti3Al layer/α2-Ti3Al + δ-Ti2Ni/α2-Ti3Al layer/τ3-Al3Ti2Ni + B2/TAN。深入研究了保温时间对钎焊接头界面组织和连接性能的影响。结果表明：Ni元素从熔融钎料向TAN母材的扩散决定了界面组织的演化,随着保温时间的延长促进了扩散层的增厚,同时导致钎缝宽度逐渐减小。接头剪切强度测试结果显示当保温时间为15分钟时,获得的最大接头室温剪切强度和高温(600℃)剪切强度分别是248.6MPa和166.4MPa。接头断口分析表明在剪切实验中裂纹主要沿着连续的金属间化合物层产生和扩展。     

Ti2AlNb合金瞬时液相扩散连接接头界面组织及性能分析

采用Ti/Ni作为中间层实现了Ti2AlNb合金的连接(transient liquid phase, TLP)，研究了TLP连接接头的界面组织及其形成机制，并且分析了不同保温时间对接头界面组织和力学性能的影响规律. 结果表明,Ti2AlNb合金TLP连接接头主要表现为等温凝固区和冷却凝固区两个明显的特征区域. 接头的典型界面组织为Ti2AlNb/B2/Nb3Al+B2+τ3+Ti2Ni/ Ti2AlNb. 随着保温时间的延长，接头中Nb3Al和Ti2Ni相消失，τ3相不断减少，B2相不断增多. 当连接温度为1 180 ℃，保温时间为20 min时，接头的室温抗剪强度最大，达到428 MPa，高温(650 ℃)抗剪强度达到407 MPa. 接头的断裂主要发生在冷却凝固区的τ3相上.     

复合粉末中间层钎焊Si0_2陶瓷与TC4合金的接头组织与性能

采用46.4%Ag-18.0%Cu-35.6%Ni(质量分数)复合粉末中间层实现了SiO_2陶瓷和TC4钛合金的良好钎焊。使用扫描电镜、能谱分析和X射线衍射等方法对钎焊接头的界面组织和力学性能进行了研究。结果表明,SiO_2陶瓷和TC4钛合金的连接接头成形良好,SiO_2陶瓷/Ag-Cu/Ni/TC4钛合金钎焊接头的界面结构为:SiO_2/Ti_4O_7+TiSi_2/Ti_2Cu+Ti_2Ni/α-Ti+Ti2Cu+Ti_2Ni过共晶组织/α-Ti+Ti_2Cu+Ti_2 Ni过共析组织/α-Ti/TC4。当钎焊温度为970℃、保温时间为30 min时,使用Ag-Cu/Ni粉末中间层钎焊SiO_2陶瓷与TC4钛合金的接头达到最高抗剪强度38 MPa。     

ZrO_2陶瓷与TC4真空钎焊接头组织和性能

由于陶瓷-金属构件能够实现性能互补,其钎焊技术和接头可靠性已经成为研究热点,包括钎料选用、炉中气氛控制,以及工艺参数优化等。文中采用Ag70-Cu-Ti4.5钎料进行了ZrO_2陶瓷和TC4合金的真空钎焊连接,研究了钎焊温度与保温时间对钎焊接头四点弯曲强度与界面组织结构的影响。结果表明,最佳钎焊工艺参数为钎焊温度875℃,保温时间15 min,钎焊接头强度最高可达191.9 MPa,但钎焊温度的较小变化会引起接头强度的急剧下降。从钎料中溶解的Ti和Cu元素对ZrO_2/TC4钎焊接头的组织演变具有主要影响,钎焊接头界面组织为ZrO_2/TiO+Cu_2Ti_4O+Cu_4Ti_3/Ag+Cu_3Ti_3O/Ti_2Cu_3/Ti_2Cu_3+CuTi_2/CuTi_2+CuTi_3/TC4。在一定范围内,反应层厚度增大,界面组织细小均匀,可以获得较好的接头性能。     

Ti-50Ni钎焊TZM与ZrCp-W接头界面组织及性能

采用Ti-50Ni(at%)钎料实现了TZM合金与ZrC_p-W复合材料的真空钎焊连接,通过SEM、EDS、XRD等方法分析了接头界面的微观组织结构,研究了钎焊温度对TZM/Ti-50Ni/ZrC_p-W接头界面组织及性能的影响。结果表明:钎焊接头的典型界面结构为TZM/Ti-Mo+TiNi_3+Mo-Ti-W/Ti Ni+TiNi_3+W(s,s)+(Ti,Zr)C/ZrC_p-W。随着钎焊温度的升高,Ti-Mo固溶体层宽度逐渐增大,线状条纹增多、增宽,组织逐渐粗大,晶界变圆滑;接头的抗剪强度随钎焊温度升高先升高后降低,当钎焊温度为1340℃,保温10 min时,接头获得最大抗剪强度为146 MPa。     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis     

Preface

<正>We are pleased to present this Special Issue of Transactions of Nonferrous Metals Society of China containing selected papers from the First Asian Conference on Aluminum Alloys(ACAA-2013),held in Beijing,China,13–17 October 2013.This conference has been initiated,with approval of     

Information for Contributors

The Transactions of Nonferrous Metals Society of China, founded in 1991 and sponsored by The Nonferrous Metals Society of China, is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology, including mineral processing, extraction metallurgy, metallic materials and heat treatments, metal working, physical metallurgy, powder metallurgy, with the emphasis on fundamental science. It is the unique preeminent publication in English for scientists, engineers, under/post-graduates on the field of nonferrous metals industry. This journal is covered by many famous abstract/index systems and databases such as SCI Expanded, Ei Compendex Plus, 1NSPEC, CA, METADEX, AJ and JICST.     

INTRODUCTION TO PATENTS

The invention provides a method of making a mold which can reduce SOx generation rate while preventing decrease in hardening rate in the case of using sulfuric acid for a hardener composition. The method has a mixture step in which fire-resistant particles, a hardener composition and a binder composition are mixed to obtain a composition for a mold. The hardener composition contains sulfuric acid. In the mixture step, sodium carbonate is added. A molar ratio of the sulfuric acid to the sodium carbonate is 0.5 or more and 4.0 or less.     

China Foundry Week 2014

China Foundry Week, hosted by the Foundry Institution of Chinese Mechanical Engineering Society （FICMES） each year, is a large academic event in China. It is one of the ten high-impact activities sponsored by the Chinese Mechanical Engineering Society.     

17th Conference of Hydrodynamic and Electromechanical Control Engineering Call for papers

正1.Contents In order to promote the academic exchanges and technical communication of the research in the field of fluid power transmission and control,fluid control engineering specialized committee of the Chinese Society of Theoretical and Applied Mechanics will hold the 17th Conference of Hydrodynamic and Electromechanical Control Engineering on July 27-29,2014 in Tibet,Lhasa city.     

Formulas of Tension of Continuous Rolling Process

The development of computer controlled continuous rolling process calls for a mathematical expression that can express the inequality condition of "constant flow". Tension is the link of the continuous rolling process. From the condition of dynamic equilibrium, a differential equation of tension is given out. On the basis of the physical rules established from the industrial practice and experimental studies, the law of volume constancy, the linear relation of forward slip and tension, the state equation of continuous rolling, the formula of dynamic tension, and the formula of static tension have been obtained. These formulae reflect the functional relations between tensions, thickness, roll velocity, and time in the continuous rolling process. It is implied that the continuous rolling process is a gradually steady, controllable, and measurable dynamic system. An assumption of predicting the thickness of a steel plate using these tension formulae is also put forward.