Surface modification of spherical LiNi1/3Co 1/3 Mn1/3O2 with Al2O3 using heterogeneous nucleation process

To improve the cycle stability at high voltage and high charge/discharge rate, spherical LiNi1/3Co1/3Mn1/3O2 was coated with Al2O3 by using heterogeneous nucleation process, and the physical and electrochemical properties were studied. The SEM images show that there is a uniform coating on the modified spherical LiNi1/3Co1/3Mn1/3O2. The electrochemical tests indicate that the properties of LiNi1/3Co1/3Mn1/3O2 coated with 0.5% aluminum oxide are the best. The initial capacities are 150 and 173 mA.h/g at the rate of I C in the voltage range of 2.7-4.3 V and 2.7-4.6 V, respectively, and the discharge capacities maintain about 99% and 85% after 30 cycles, respectively. While those of the bare LiNi1/3Co1/3Mn1/3O2 are only 90% and 75%, respectively. The CV tests of LiNi1/3Co1/3Mn1/3O2 show that Al203-coating can restrain the oxide-reduction peak currents fading during the charge/discharge course.     

前处理工艺对Li[Ni1/3Mn1/3Co1/3]O2正极材料结构、形貌和电化学性能的影响（英文）

以[Ni1/3Co1/3Mn1/3]3O4和氢氧化锂为原料,分别采用球磨法和液相法前处理工艺制备层状正极材料Li[Ni1/3Mn1/3Co1/3]O2。采用X？射线衍射（XRD）、场发射扫描电镜（FESEM）、恒流充放电等手段对材料的物理和电化学性能进行表征。结果表明：采用不同前处理工艺制备出的Li[Ni1/3Mn1/3Co1/3]O2材料在结构、形貌和电化学性能上有较大差异;与球磨处理法制备的材料相比,采用液相法前处理工艺制备的Li[Ni1/3Mn1/3Co1/3]O2不但保持了前驱体较好的球形形貌,同时还具有较好的循环稳定性和倍率性能;该样品在20mA/g电流密度下,首次放电容量为178mA·h/g,50次循环后,容量保持率达98.7%;在1000mA/g电流密度下,样品容量为135mA·h/g。     

锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2的制备及性能研究

采用溶胶-凝胶法制备了锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2,并考察了烧结温度对材料结构、表面形貌和电化学性能的影响.XRD和SEM测试结果表明,900℃下烧结得到的样品是粒径在0.3～0.5 μm范围的球形粒子,具有最佳的阳离子有序度;充放电测试结果表明,其在0.1C倍率下首次放电容量达到148.8...     

Uniform AlF3 thin layer to improve rate capability of LiNi1/3Co1/3 Mn1/3O2 material for Li-ion batteries

LiNi1/3Co1/3Mn1/3O2 was coated with uniform nano-sized AlF3 layer by chemical precipitation method to improve its rate capability. The samples were characterized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), charge-discharge cycling, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). Uniform coated layer with a thickness of about 3 nm was observed on the surface of LiNi1/3Co1/3Mn1/3O2 particle by TEM. At 0.5C and 2C rates, 1.5% (mass fraction) AlF3-coated LiNi1/3Co1/3Mn1/3O2/Li in 2.8-4.3 V versus Li/Li+ after 80 cycles showed less than 3% of capacity fading, while those of the bare one were 16.5% and 45.9%, respectively. At 5C rate, the capacity retention of the coated sample after 50 cycles maintained 91.4% of the initial discharge capacity, while that of the bare one decreased to 52.6%. EIS result showed that a little change of charge transfer resistance of the coated sample resulting from uniform thin AlF3 layer was proposed as the main reason why its rate capability was improved obviously. CV result further indicated a greater reversibility for the electrode processes and better electrochemical performance of AlF3-coated layer.     

Preparation of layered oxide Li（Co1/aNi1/3Mn1/3）O2 via the sol-gel process

To obtain homogenous layered oxide Li(Co1/3Ni1/3Ni1/3Mn1/3)O2 as a lithium insertion positive electrode material,the sol-gel process using citric acid as a chelating agent was applied.The material Li(Co1/3,Ni1/3Mn1/3)O2 was synthesized at different calcination temperatures.XRD experiment indicated that the hyered Li(Co1/3Ni1/3Mn1/3)O2material could he synthesized at a lower temperature of 800℃,and the oxidation state of Co,Ni,and Mn in the cathode confirmed by XPS were 3, 2,and 4,respectively.SEM observations showed that the synthesized material could form homogenous particle morphology with the particle size of about 200nm In spite of different calcination temperatures,the charge-discharge curves of all the samples for the initial cycle were similar,and the cathode synthesized at 900℃ showed a small irreversible capacity loss of 11.24% and a high discharge capacity of 212.2 mAh.g-1 in the voltage range of 2.9-4.6 V.     

Synthesis and electrochemical characterization of layered Li[Ni1/3CO1/3 Mn1/3]O2 cathode material for Li-ion batteries

1 INTRODUCTIONDue to the high cost of LiCoO2,a commonlyused cathode material in commercial rechargeablelithium-ion batteries , much efforts have been madeto develop cheaper cathode materials than LiCoO2,Li Ni O2and Li MnO2have been studied extensivelyas possible alternatives to LiCoO2[1 4 ]. Stoichio-metric Li Ni O2is knownto be difficult to synthesizeandits multi-phase reaction during electrochemicalcyclingleads to structural degradation,andlayeredLi MnO2has a significant drawback…     

Li1+x(Fey/2Niy/2Mn1-y)1-xO2正极材料的合成及电化学性能

采用低温共沉淀-水热-煅烧法合成了锂离子电池Fe-Ni-Mn体系正极材料Li1+x(Fey/2Niy/2Mn1-y)1-xO2,并用XRD、SEM、ICP光谱和电化学性能测试对材料进行了表征.XRD测试和ICP分析表明,Fe、Ni取代Li2MnO3中的部分Mn,形成很好的固溶结构yLiFe1/2Ni1/2O2-(1-y)Li2MnO3 (y=0.l,0.2,0.3,0.4,0.5).SEM测试表明,取代量y不同,材料的表观形貌有所不同,y=0.4时材料的颗粒粒径均匀、较小,呈类球形结构.电化学性能测试表明,当y=0.4时,循环稳定性最好,充放电50次后放电比容量仍可维持在195.0 mAh/g,放电中值电压为3.5 V,y=0.4时样品在大倍率放电下的电化学性能表现良好.     

Si4+和F-掺杂对LiNi1/3Co1/3Mn1/3O2结构和电化学性能的影响

以Li2CO3、NiO、Co2O3、MnO2、LiF和SiO2为原料,采用机械力活化固相法制备了Si4+和F-掺杂的锂离子电池正极材料LiNi1/3Co 1/3Mn1/3O2.通过X射线衍射(XRD)、扫描电镜(SEM)和电化学性能测试等技术研究了LiNi1/3Co1/3Mn1/3O2的结构特征、形貌及电化学性能等.结...     

锂离子电池正极材料LiNi_1/3Co_1/3Mn_1/3O_2的研究进展

介绍了一种新型的锂离子电池正极材料LiNi1/3Co1／3Mn1／3O2的最新研究状况,描述了材料的晶体及电子结构,以及电化学性能;重点总结了现今国内外制备此材料的几种主要合成方法及研究进展;同时,介绍了不同掺杂元素（Fe、B、Al、Ti）对材料的改性作用。     

Surface modification of LiCo0. 05Mn1.95O4 cathode by coating with SiO2-TiO2 composite

1　INTRODUCTIONSincethefirstcommercializationbySonyCorpo rationintheearly 1990s ,thelithium ionbattery(LIB)hasbecomeamajorproducttodominatethemarketforsmallrechargeablebatteries .Further more ,Li ionbatteriesareexpectedtobeusedasalarge scaleenergystoragedeviceforelectricvehices(EV ) [1] .ThoughvarioustypesofcathodematerialssuchasLiCoO2 ,LiNiO2 ,LiMn2 O4 ,andsubstitutedtran sitionmetaloxidesarecurrentlyusedincommercial izedLi ionbatteries[2 ,3] ,LiCoO2 inthesecathodematerialsismost…     

LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的合成与电化学性能

以溶胶前驱体为纺丝液,通过静电纺丝法合成锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维.采用原子力显微镜(AFM)、X射线衍射(XRD)、充放电实验对纳米纤维的形貌、结构和电化学性能进行研究.结果表明,纳米纤维的直径在150～200 nm之间,且具有典型的α-NaFeO2层状结构.LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的首次放电容量均超过170 mAh·g-1,50次循环后容量保持率在90%以上.     

Synthesis of LiNi1/3CO1/3Mn1/3O2 cathode material via oxalate precursor

Using oxalic acid and stoichiometrically mixed solution of NiCl2, CoCl2, and MnCl2 as starting materials, the triple oxalate precursor of nickel, cobalt, and manganese was synthesized by liquid-phase co-precipitation method. And then the LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion battery were prepared from the precursor and LiOH-H2O by solid-state reaction. The precursor and LiNi1/3Co1/3Mn1/3O2 were characterized by chemical analysis, XRD, EDX, SEM and TG-DTA. The results show that the composition of precursor is Ni1/3Co1/3Mn1/3C2O4·2H2O. The product LiNi1/3Co1/3Mn1/3O2, in which nickel, cobalt and manganese are uniformly distributed, is well crystallized with a-NaFeO2 layered structure. Sintering temperature has a remarkable influence on the electrochemical performance of obtained samples. LiNi1/3Co1/3Mn1/3O2 synthesized at 900 ℃ has the best electrochemical properties. At 0.1C rate, its first specific discharge capacity is 159.7 mA·h/g in the voltage range of 2.75-4.30 V and 196.9 mA·h/g in the voltage range of 2.75-4.50 V; at 2C rate, its specific discharge capacity is 121.8 mA·h/g and still 119.7 mA·h/g after 40 cycles. The capacity retention ratio is 98.27%.     

Effects of synthesis conditions on the structural and electrochemical properties of layered LiNi1/3Co1/3Mn1/3O2 cathode material via oxalate co-precipitation method

The uniform layered LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries was prepared by using (Ni1/3Co1/3Mn1/3)C2O4 as precursor synthesized via oxalate co-precipitation method in air. The effects of calcination temperature and time on the structure and electrochemical properties of the LiNi1/3Co1/3Mn1/3O2 were systemically studied. XRD results revealed that the optimal calcination conditions to prepare the layered LiNi1/3Co1/3Mn1/3O2 were 950°C for 15 h. Electrochemical measurement showed that the sample prepared under the such conditions has the highest initial discharge capacity of 160.8 mAh/g and the smallest irreversible capacity loss of 13.5% as well as stable cycling performance at a constant current density of 30 mA/g between 2.5 and 4.3 V versus Li at room temperature.     

Preparation of Li[Ni1/3Co1/3Mn1/3]O2 powders for cathode material in secondary battery by solid-state method

Employing Li2CO3, NiO, Co3O4, and MnCO3 powders as starting materials, Li[Ni1/3Co1/3Mn1/3]O2 was synthesized by solid-state reaction method.Various grinding aids were applied during milling in order to optimize the synthesis process.After successive heat treatments at 650 and 950 ℃, the prepared powders were characterized by X-ray diffraction (XRD) analysis, scanning electron microscopy, and transmission electron microscopy.The powders prepared by adding salt (NaCl) as grinding aid exhibit a clear R3m layer structure.The powders by other grinding aids like heptane show some impurity peaks in the XRD pattern.The former powders show a uniform particle size distribution of less than 1 μm average size while the latter shows a wide distribution ranging from 1 to 10 μm.Energy dispersive X-ray (EDX) analysiss show that the ratio of Ni, Co, and Mn content in the powder is approximately 1/3, 1/3, and 1/3, respecively.The EDX data indicate no incorporation of sodium or chlorine into the powders.Charge-discharge tests gave an initial discharge capacity of 160 mAh·g-1 for the powders with NaCl addition while 70 mAh·g-1 for the powders with heptane.     

Effect of calcination temperature on characteristics of LiNi1/3Co1/3Mn1/3O2 cathode for lithium ion batteries

LiNi1/3Co1/3Mn1/3O2 was synthesized by sol-gel method and effect of calcination temperature on characteristics of LiNi1/3Co1/3Mn1/3O2 cathode was investigated. The structure and characteristics of LiNi1/3Co1/3Mn1/3O2 were determined by XRD, SEM and electrochemical measurements. The results show that the compound LiNi1/3Co1/3Mn1/3O2 has layered structure with hexagonal lattice. With the increase of calcination temperature, the basicity of the material decreases, and the size of primary particle rises. The LiNi1/3Co1/3Mn1/3O2 calcined at 900 ℃ for 12 h shows excellent electrochemical performances with large reversible specific capacity of 157.5 mA-h/g in the voltage range of 2.75-4.30 V and good capacity retention of 94.03% after 20 charge/discharge cycles. Capacity of LiNi1/3Co1/3Mn1/3O2 increases with enhancement of charge voltage limit, and specific discharge capacities of 179.4 mA.h/g, 203.1 mA.h/g are observed when the charge voltages limit are fixed at 4.50 V and 4.70 V, respectively.     

合成条件对氢氧化物共沉淀法制备锂离子电池层状正极材料Li[Ni_（1/3）Co_（1/3）Mn_（1/3）]O_2的影响

以共沉淀法制备的过渡金属氢氧化物前驱体合成锂离子电池层状正极材料Li[Ni1/3Co1/3Mn1/3]O2。考察氨与过渡金属阳离子的配位效应对Li[Ni1/3Co1/3Mn1/3]O2材料的结构和电化学性能的影响。SEM分析结果表明,当NH3·H2O与过渡金属阳离子的总摩尔比为2.7：1时,获得了分布均一的颗粒为过渡金属氢氧化物共沉淀,合成的Li[Ni1/3Co1/3Mn1/3]O2材料的平均粒径约为500nm,振实密度接近2.37g/cm3,接近商品化的LiCoO2正极材料的振实密度。XRD分析结果表明,合成的Li[Ni1/3Co1/3Mn1/3]O2材料具有六角晶格层状结构。Li/Li[Ni1/3Co1/3Mn1/3]O2电池在2.8-4.5V电压范围内的0.1C倍率测试结果表明,首次放电容量达181.5mA·h/g,0.5C倍率循环50次后的放电容量为170.6mA·h/g。     

La1/3Sr2/3Mn1-xFexO3(x=0,0.05)中电荷有序现象的超声研究

系统研究了La1／3Sr2／3Mn1-xFexO3(x=0，0．05)单相多晶样品在20--300K温区内的电荷输运性质和超声特性，结果表明，La1／3Sr2／3MnO3样品在235K存在明显的电荷有序现象，但是极少量的Fe取代Mn就会有效地抑制电荷有序现象的发生，伴随电荷有序现象的发生声速出现极大的软化，其相对变化超过5％，这表明La1／3Sr2／3Mn1-xFexO3中存在剧烈的电-声子相互作用，分析指出该电-声子耦合主要起源于Jahn-Teller效应。     

Zn对锂电池材料LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2结构和电化学性能的影响

采用共沉淀法掺入少量Zn得到Li(Ni1/3Co1/3Mn1/3)1-xZnxO2材料。通过X射线衍射、光电子能谱(XPS)和电化学测试研究掺杂对其晶体结构、元素价态和电化学行为的影响。结果表明:掺入Zn增大晶格常数;在粉末颗粒表面的Zn含量是颗粒内部的数十倍;掺杂后Co、Mn依然保持+3、+4价,但是Ni由+2、+3混合价态组成;掺入少量Zn阻止电极在4.5V电位下的不可逆氧化反应;掺入Zn有效改善高截止电压下的循环容量保持能力,其作用与改变材料表面状态有关。     

Synthesis and electrochemical properties of Li[NixCoyMn1-x-y]02 (x, y=2/8, 3/8) cathode materials for lithium ion batteries

The uniform layered Li(Ni2/8Co3/8Mn3/8)O2, Li(Ni3/8Co2/8Mn3/8)O2, and Li(Ni3/8Co3/8Mn2/8)O2 cathode materials for lithium ion batteries were prepared using the hydroxide co-precipitation method. The effects of calcination temperature and transition metal contents on the structure and electrochemical properties of the Li-Ni-Co-Mn-O were systemically studied. The results of XRD and electrochemical performance measurement show that the ideal preparation conditions were to prepare the Li(Ni3/8Co3/8Mn2/8)O2 cathode material calcined at 900℃ for 10 h. The well-ordered Li(Ni3/8Co3/8Mn2/8)O2 synthesized under the optimal conditions has the I003/I104 ratio of 1.25 and the R value of 0.48 and pedance of 558 Ω after the first cycle. The decrease of Ni content results in the decrease of discharge capacity and the bad cycling perform-ance of the Li-Ni-Co-Mn-O cathode materials, but the decreases of Mn content and Co content to a certain extent can improve the electro-chemical properties of the Li-Ni-Co-Mn-O cathode materials.     

以Mn3O4为前驱体制备尖晶石型LiMn2O4及其性能

采用改进的固相反应法合成了高性能的锂离子电池正极材料LiMn2O4。首先,以廉价的MnSO4为原料,通过水解氧化法制备纳米级Mn3O4前驱体;然后,将Mn3O4和Li2CO3混合均匀,在750℃固相反应20 h,得到尖晶石型LiMn2O4。用X射线衍射(XRD)和扫描电镜(SEM)对Mn3O4前驱体和LiMn2O4样品进行表征,用充放电测试和循环伏安技术对LiMn2O4样品进行电化学性能研究。结果表明:所制备的LiMn2O4具有完整的尖晶石型结构,且晶体粒子分布均匀。所制备的LiMn2O4材料在3.0~4.4 V之间,室温(25℃)下,在0.2C倍率下首次放电比容量为130.6 mA.h/g;在0.5C倍率下首次放电比容量为127.1 mA.h/g,30次循环后,容量仍有109.5 mA.h/g,且样品具有较好的高温性能。