共查询到17条相似文献,搜索用时 125 毫秒
1.
2.
H68黄铜断裂过程的透射电镜原位观察 总被引:3,自引:0,他引:3
采用透射电镜动态拉伸、原位观察研究了低层错能合金H68黄铜断裂的微观过程。结果发现:黄铜薄膜试样拉伸时,裂尖首先发射位错,平衡时形成无位错区和反塞积位错群;裂尖前方较厚区域可以发生孪生变形,形成形变孪晶,微裂纹在孪晶中形核、扩展,导致裂纹呈Z字形扩展;裂尖无位错区也可能形成微孪晶,微裂纹在微孪晶中形核,使裂纹呈不连续扩展;微裂纹也可以从主裂纹顶端连续形核、扩展。 相似文献
3.
Ti-24Al-11Nb合金在室温下恒载荷动态充氢以及交变载荷动态充氢时,氢通过促进裂纹在滑移面上的解一,促进了裂纹扩散,不连续的氢致解理裂纹优先在α2相形核,α2/β相界面是裂纹扩展的有效障碍,氢通过促进裂尖位错的发射、解理微裂无位错区(DFZ)的形核以及解理裂纹,导致氢致解理断裂。 相似文献
4.
5.
6.
7.
8.
9.
10.
11.
INSITUTEMOBSERVATIONOFINITIATIONANDPROPAGATIONOFCRACKSINNiAlFeINTERMETALLICSY.X.Lu;C.H.Tao;J.W.Zhang;M.L.XueandD.Z.Yang(Beiji... 相似文献
12.
13.
14.
采用计算机模拟了位错和位错偶沿单一滑移系从裂纹尖端的发射,考察了滑移面取向、外加载荷、晶格摩擦力以及位错发射的临界应力强度因子对所发射的位错数量、塑性区与无位错区大小以及裂关残余应力强度因子的影响研究表明,位错从裂纹尖端发射的临界应力强度因子对无位错区的存在和其大小起决定作用,而外加载荷与晶格摩擦力主要影响位错发射的数量以及塑性区大小.在I型载荷作用下,滑移面与裂纹面的夹角越大,从裂尖发射出的位错数量越多,位错对裂纹的屏蔽效应也越大当裂纹发射位错后的残余应力强度因子仍然较大时,位错偶就有可能在裂纹尖端附近产生井沿着几个滑移面发射,但发射出的位错偶对裂纹没有明显的屏蔽作用在滑移面不垂直于裂纹面时,发射出的位错或位错偶关于裂纹面呈不对称分布 相似文献
15.
16.
YAO Kefu TANG Naiyong CHEN Nanping Tsinghua University Beijing China Originally published in ACTA METALL SIN 《金属学报(英文版)》1989,2(6):433-438
The development of dislocation structures in the plastic zone ahead of a crack tip has been in-vestigated in a duplex stainless steel during in-situ deformation experiments in a scanningtransmission electron microscope.It was found that the dislocation distribution wassignificantly different in the ferrite and in the austenite.In the ferrite grains,the dislocationsemitted by the crack tip may cross-slip out of the original slip planes and form a broad plasticzone.However,in the austenite,the dislocation free zone is small and the dislocations emittedby the crack pile up in its slip plane.The selection of slip systems at the crack tip depends onthe crack tip Schmid factors in both phases.But after large deformation,the selection of thesecond slip systems at the craek tip in austenite does not depend on the Schmid factors. 相似文献