等离子喷涂与超音速火焰喷涂NiCr-Cr3C2涂层组织与摩擦磨损性能研究

目的 研究等离子喷涂与超音速火焰喷涂NiCr-Cr3C2涂层的组织、力学性能和摩擦磨损性能。方法 采用等离子喷涂与超音速火焰喷涂工艺制备NiCr-Cr3C2涂层,并采用X射线衍射仪（XRD）、扫描电镜（SEM）、万能试验机、显微硬度计和高速往复摩擦磨损试验机,系统地分析了两种工艺所得涂层的物相、组织、结合强度、硬度及摩擦磨损性能。结果 两种工艺制备的NiCr-Cr3C2涂层与基体界面结合效果良好。等离子喷涂NiCr-Cr3C2涂层为层片状组织,层间可见微裂纹,孔隙率较高;超音速火焰喷涂NiCr-Cr3C2涂层组织均匀,无明显微裂纹,可见少量微小孔隙。物相分析表明,等离子喷涂涂层由NiCr、Cr3C2和Cr7C3相组成,而超音速火焰喷涂涂层由NiCr和Cr3C2相组成。超音速火焰喷涂NiCr-Cr3C2涂层的耐磨性优于等离子喷涂涂层,等离子喷涂涂层和超音速火焰喷涂涂层的稳态摩擦系数分别为0.4和0.6。随载荷升高,两种工艺制备的NiCr-Cr3C2涂层摩擦系数均显著下降。磨损后,等离子喷涂NiCr-Cr3C2涂层表面具有明显的凹痕和剥落,而超音速火焰喷涂NiCr-Cr3C2涂层磨痕表面较光滑,未见明显剥落。两种工艺制备的涂层磨损机制均为磨粒磨损和疲劳磨损。结论 超音速火焰喷涂NiCr-Cr3C2涂层较等离子喷涂涂层组织更为致密,具有更为优良的综合力学性能和耐磨性,等离子喷涂制备的NiCr-Cr3C2涂层的减摩性较好。     

高效能超音速等离子喷涂NiCr-Cr3C2涂层性能研究

采用自行研制的高效能超音速等离子喷涂系统(HEPJet)制备了NiCr-Cr3C2涂层,并对涂层性能进行测试.结果表明,喷涂粒子速度高达460 m/s,实现了低功率、小气体流量获得超音速涂层的目的;HEPJet制备的NiCr-Cr3C2涂层其结合强度为60 MPa,显微硬度为926 HV0.3,沉积效率为54％,其抗高温氧化性能是12CrMoV钢的17倍,其常规性能赶超JP5000制备的NiCr-Cr3C2涂层.涂层表面的Cr2O3氧化膜与碳化物硬质相组成连续、致密而均匀的保护层是NiCr-Cr3C2涂层抗高温氧化性好的主要原因.     

激光等离子复合热源喷涂工艺沉积机理研究

目的提高涂层的结合强度和改善微观组织结构。方法选取WC-10Co4Cr喷涂材料,分别通过激光等离子复合热源喷涂工艺以及等离子喷涂工艺制备涂层,对涂层组织与基本性能进行检测,对两种不同喷涂工艺的沉积机理作对比分析研究。研究复合热源喷涂涂层微观组织结构以及涂层与基体间结合方式较等离子喷涂涂层的变化。利用高速摄像仪对激光等离子复合热源喷涂以及等离子喷涂的工艺过程进行跟踪监测和分析,研究复合热源沉积过程中,基体表面微熔池的形成及粉末粒子在不同沉积工艺过程中熔融状态的对比,分析等离子喷涂涂层和复合热源喷涂涂层的沉积机理。结果等离子喷涂WC-10Co4Cr涂层以机械结合方式为主,涂层结合强度为39.5 MPa,孔隙率为1.7%,而激光等离子复合热源喷涂WC-10Co4Cr涂层实现了冶金结合,其结合强度提升到91 MPa,孔隙率降低到0.86%。结论激光等离子复合热源喷涂工艺可以有效提升涂层的结合力,改善涂层组织致密性,更有利于涂层的耐磨耐腐蚀性能。     

等离子喷涂Al_2O_3(13%TiO_2)涂层和NiCr-Cr_3C_2涂层的组织性能研究

通过等离子喷涂方法在穿孔顶头尾部材料42CrMo钢表面分别制备NiCr-Cr3C2涂层和Al2O3(13%TiO2)涂层,运用OM,XRD,SEM等分析测试手段对涂层的组织、形貌和物相成分进行表征,并对两种涂层进行了显微硬度及抗热震性能实验.结果表明:喷涂涂层为典型的层状结构,涂层与基体为机械结合.Al2O3(13%TiO2)涂层以亚稳相γ-Al2O3相为主要相,同时存在α-Al2O3相.喷涂形成NiCr-Cr3C2涂层后物相成分为Cr23C6、Cr7C3、Cr3C2等Cr的碳化物.NiCr-Cr3C2涂层和Al2O3(13%TiO2)涂层的表面平均显微硬度分别为586.4HV,和557.7HV.其平均热震循环次数分别为25次和18次.     

不同摩擦参数下NiCr-Cr3C2涂层摩擦学性能研究

采用超音速等离子喷涂工艺制备了NiCr-Cr3C2涂层,研究了摩擦副、载荷、摩擦频率等不同摩擦条件对涂层摩擦学性能的影响。结果表明:超音速等离子制备的NiCr-Cr3C2涂层均匀致密,具有较高硬度;摩擦副和载荷对摩擦系数有较大影响,摩擦频率对摩擦系数影响较小。     

等离子喷涂 NiCr-Cr3C2基复合自润滑涂层的组织及摩擦学性能

将NiCr-Cr3C2复合粉和Ni包MoS2粉按不同比例混合,制成三种喷涂粉末,采用等离子喷涂技术在304不锈钢表面制备复合自润滑涂层,并对涂层的物相组成、显微组织及摩擦磨损性能进行了研究。结果表明:三种涂层的物相组成相同,主相均为Cr7C3,Ni和MoS2;涂层与基体的结合为机械结合,孔隙率较低,表面有少量微裂纹;喷涂粉末中的Ni包MoS2粉偏少或偏多都会导致涂层的摩擦磨损性能变坏,Ni包MoS2粉质量分数为30%时,涂层的摩擦系数及磨损率最低,分别约为0.36和3.3×10-4mg/s。     

超音速等离子喷涂NiCrCr3C2/Mo复合涂层的高温摩擦磨损性能*

采用超音速等离子喷涂制备了NiCr-Cr3C2/Mo复合涂层,借助扫描电子显微镜(SEM)、能谱仪(EDS)、显微硬度计、高温摩擦磨损试验机等手段,研究了涂层的微观组织、显微硬度及涂层在25、300、500、750℃下的摩擦磨损性能。结果表明:制备的NiCr-Cr3C2/Mo复合涂层Mo相分布均匀,组织致密、硬度高;温度对涂层的摩擦因数影响显著,随温度的升高,摩擦因数呈先下降后上升再下降的趋势,750℃时因摩擦界面生成MoO3减摩相使摩擦因数最低;NiCr-Cr3C2/Mo复合涂层在高温下以氧化疲劳剥落为主要失效机制,涂层表面复合氧化膜的形成特点将直接影响涂层的摩擦磨损性能,MoO3的形成是显著提高涂层减摩效果的主要因素。     

等离子喷涂NiCr-Cr3C2涂层对油田采出液的耐垢性分析

采用大气等离子喷涂制备NiCr-Cr3C2涂层,通过涂层显微组织观察、X射线衍射分析、能谱分析、油田采出液表面能计算及挂片试验,研究Cr3C2-NiCr涂层对油田采出液耐垢性能的影响.结果表明:等离子喷涂NiCr-Cr3C2涂层对油田采出液接触角和表面能较低,垢物CaCO3不易附着,结垢量较少,体现出良好的耐垢性;涂层表面结垢物分布较均匀,且Ni、Cr元素参与形成垢物,而基体结垢物为CaCO3、Fe3O4,且多分布于腐蚀坑处.     

B4 C 含量对等离子喷涂 NiCoCrAlY / Al2 O3 -B4 C复合涂层力学性能的影响

目的提高等离子喷涂NiCoCrAlY/Al2O3复合涂层的摩擦性能。方法采用离心喷雾造粒、化学冶金包覆和固相合金化技术制备NiCoCrAlY/Al2O3和NiCoCrAlY/B4C复合粉体,通过等离子喷涂技术制备NiCoCrAlY/Al2O3-B4C复合涂层。对涂层的显微结构、结合强度和显微硬度进行表征,研究B4C含量对等离子喷涂NiCoCrAlY/Al2O3-B4C复合涂层力学性能的影响。结果 Al2O3和B4C颗粒包覆了致密的NiCoCrAlY合金层,包覆层厚约3~5μm。等离子喷涂NiCoCrAlY/Al2O3-B4C复合涂层呈典型的层状结构,涂层结构致密,各层间结合良好。随着B4C含量的增加,复合涂层的显微硬度逐渐增大,结合强度逐渐降低,当B4C质量分数达到30%时,涂层的显微硬度比未添加B4C时提高了1.4倍,结合强度比未添加B4C时降低了26%。涂层在拉伸试验中发生了典型的脆性断裂,断裂位置发生在涂层内部。结论向等离子喷涂NiCoCrAlY/Al2O3复合涂层中添加B4C,可显著提高涂层的显微硬度,但会使涂层的结合强度有一定程度降低。     

等离子喷涂NiCr-Cr_3C_2涂层高温摩擦磨损性能研究

研究了等离子喷涂NiCr-Cr3C2涂层的高温磨损性能,与配对摩擦副相比,涂层在滑动摩擦440 m(6000个周期)之后,磨损深度和磨损体积很小,涂层在高温条件下具有优异的抗磨损性能,能够满足高温条件下的磨损要求。涂层的磨损机制主要为开始以氧化磨损为主,逐步过渡到以磨粒磨损和黏着磨损为主。经过上车试验证明NiCr-Cr3C2涂层可以应用于内燃机的气缸套。     

汽轮机超音速火焰喷涂 NiCr-Cr3C2涂层

目的 通过热喷涂涂层,解决 350 MW 超临界机组再热第一级静叶栅的高温冲蚀问题。 方法 采用超音速火焰喷涂制备了 NiCr-Cr₃C₂ 涂层,测试了涂层的显微组织、孔隙率、显微硬度、结合强度及高温冲蚀性能,并对涂层在冲蚀条件下的失效机理进行分析。 结果 实验室条件下, NiCr-Cr₃C₂ 涂层孔隙率为 0 . 98% ,显微硬度达到 1061 . 2 HV0 . 3 ,结合强度约为 80 MPa。 装机试车时,0 . 22 mm 厚的 NiCr-Cr₃C₂涂层可使再热第一级静叶的寿命延长 3 倍左右。 结论 采用 NiCr-Cr₃C₂ 涂层可显著延长静叶寿命,小角度粒子犁削冲蚀是涂层加速失效的主要原因。     

基于遗传神经网络的等离子喷涂纳米ZrO2-7%Y2O3涂层工艺参数优化

将BP神经网络和遗传算法相结合用于等离子喷涂纳米ZrO2-7％ Y2O3涂层的工艺参数优化,根据正交试验结果对模型结构进行训练,建立了喷涂距离、喷涂电流、主气压力、辅气压力与涂层结合强度和显微硬度之间的BP神经网络模型,并基于遗传算法对涂层结合强度和显微硬度进行了单目标和多目标参数优化.结果表明,模型预测值与试验值十分接近,说明该网络模型是正确和可靠的.遗传算法优化的涂层最大结合强度和显微硬度(HV)分别为44.0 MPa和12.663 GPa;当涂层结合强度和显微硬度两个性能参数权重相同时,在喷涂距离90.66 mm、喷涂电流934.63 A、主气压力0.304MPa和辅气压力0.898 MPa时涂层综合性能最优.     

超音速火焰喷涂Cr3C2/NiCr涂层抗加沙空蚀性分析

采用HVOF技术在1Cr18Ni9Ti不锈钢基体上制备了Cr3C2/NiCr涂层,借助XRD,TEM,SEM等方法分析了涂层的组织形貌及相组成.以1Cr18Ni9Ti奥氏体不锈钢作为对比材料,用磁致伸缩空蚀仪配备扬沙装置测试了涂层在清水以及含沙水中抗空蚀性能.结果表明,涂层呈层状结构,含有未熔颗粒和少量孔隙,涂层由Cr3C2,Cr7C3,Cr23C6及NiCr等相组成;在清水试验中,1Cr18Ni9Ti不锈钢抗空蚀性能良好,与空蚀过程中1Cr18Ni9Ti奥氏体不锈钢产生加工硬化有直接关系;在含沙40 kg/m3试验水中,Cr3C2/NiCr涂层呈现出较好的抗空蚀性能,与涂层自身相组成以及较高硬度有关.Cr3C2/NiCr涂层破坏总是从孔隙等薄弱环节开始,而1Cr18Ni9Ti奥氏体不锈钢的破坏起始于晶界和孪晶界.     

Use of microhardness as a simple means of estimating relative wear resistance of carbide thermal spray coatings: Part 2. wear resistance of cemented carbide coatings

A selection of WC-Co and Cr₃C₂-25%NiCr coatings produced by plasma spray and high velocity oxygen fuel (HVOF) deposition techniques were subjected to various wear tests designed to simulate abrasion, cavitation, sliding, and particle erosion type wear mechanisms. All of the coatings were at least 200 μm thick and were deposited onto stainless steel substrates. In Part 1 of this contribution, the microstructures of the coatings were characterized and their mechanical properties were assessed using microindentation procedures. In this second part of the article, the behavior of the coatings when subjected to the various wear tests is reported and the utility of microhardness testing as an indication of relative wear resistance is discussed. It is shown that correctly performed, appropriate microhardness measurements are a good indication of abrasion resistance and sliding wear resistance, and also correlate well with cavitation resistance in Cr₃C₂-NiCr. The measurements were less useful for predicting erosion resistance for both Cr₃C₂-NiCr and WC-Co, however, and for abrasion resistance when WC-Co was ground against SiC. Here the contribution of micromechanisms involving fracturing and brittle failure is greater than that indicated by the coating microhardness, which is essentially a measurement of resistance to plastic deformation under equilibrium conditions.     

Microstructure and adhesion of Cr3C2-NiCr vacuum plasma sprayed coatings

Vacuum plasma spraying (VPS) was used to spray a Cr₃C₂-NiCr coating of ∼ 150, 300 and 450 μm in thickness onto a plain carbon steel substrate, employing a commercially available Cr20Ni9.5C powder. The splat microstructures observed in the coating were found to consist of a NiCr matrix with a predominant Cr₃C₂ phase, besides Cr₇C₃ and Cr₂O₃. The adhesion of the coating to the substrate was evaluated by means of interfacial indentation techniques. It has been found that the interfacial toughness value changes from 7.6 to 10.1 MPa m^1/2 when the thickness increases from 150 to 450 μm. Also, it has been found that the parameter Kca_o, determined by linear regression from the Kca versus 1 / e² curve by means of the interfacial indentation model advanced by Chicot et al., has a value of ∼ 9.8 MPa m^1/2.     

Microhardness as a simple means of estimating relative wear resistance of carbide thermal spray coatings: Part 1. characterization of cemented carbide coatings

A selection of WC-Co and Cr₃C₂-25%NiCr coatings deposited by plasma spraying and high velocity oxygen fuel (HVOF) were tested. The microstructures of the coatings were characterized, and their mechanical properties were assessed using Knoop microindentation procedures. The coatings were also subjected to various wear tests. All of the coatings were at least 200 μm thick and were deposited onto stainless steel substrates. The wear tests simulated abrasion, cavitation wear, sliding wear, and particle erosion wear. In this first part of a two-part contribution, the microstructures of the coatings are characterized and a discussion on the evaluation of mechanical properties from the microindentation response is presented. The nature of microhardness testing as applied to thermal spray coatings is evaluated as a means of assessing resistance to plastic flow, elasticity, and brittleness. In Part 2, the results of the various wear simulations are reported, and the utility of microhardness as an indicator of wear resistance is examined.     

Microstructure and corrosion properties of plasma-sprayed NiCr-Cr3C2 coatings comparison with different post treatment

The effects of laser and plasma arc remelting on the microstructure and properties of plasma-sprayed NiCr-Cr₃C₂ coatings on steel substrates have been investigated. The microstructure of the coatings has been analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the Cr₃C₂, δ-(Cr,Ni), Cr₇C₃ and Cr₂₃C₆ phases were obtained for both coatings, before and after remelting treatment. The laser remelting was operated in a continuous way with 800 W power in different scan speed, while the plasma arc remelting was operated with a plasma cladding machine under different scan currents. However, the denser microstructure of both remelted coatings can be obtained, especially for the plasma arc remelted coating. The Vickers microhardness measurement showed certain enhancement values for both remelted coatings. The corrosion behavior was evaluated through salt spray corrosion (SSC) method. Energy-dispersive spectroscopy (EDS) showed that the chloride was produced during SSC process. The higher corrosion resistance for plasma arc remelted coating may be due to the more compact microstructure, less porosity rate and tensile residual stress. Compared with laser remelting method, plasma arc remelting is a cheap, convenient and effective remelting method.     

激光热喷涂Co30Cr8W1.6C3Ni1.4Si涂层在PAO+2.5%MoDTC油中摩擦学特性

为了提高TC4合金的耐磨性能,采用激光热喷涂技术在其表面制备了Co₃₀Cr₈W_1.6C₃Ni_1.4Si涂层。通过扫描电子显微镜（SEM）和X射线衍射（XRD）分析了涂层的形貌和物相,并通过摩擦磨损实验研究了涂层在PAO+2.5% MoDTC（质量分数）油中的磨损行为。结果表明,激光热喷涂的Co₃₀Cr₈W_1.6C₃Ni_1.4Si涂层主要由Ti、WC_1-x、CoO、Co₂Ti₄O和CoAl相组成,在涂层界面形成冶金结合。在激光功率为1000、1200和1400 W时所制备的涂层平均摩擦因数分别为0.151、0.120和0.171,其对应的磨损率分别为1.17×10^-6、1.33×10^-6和2.80×10^-6 mm³?N^-1?m^-1,磨损机理为磨粒磨损,其枝晶尺寸对降磨起主要作用。     

等离子喷涂Cu-Al2O3梯度涂层的组织与耐磨性分析

针对纯陶瓷涂层由于结合强度低、孔隙率高、影响涂层耐磨性的实际,用等离子喷涂法制备了Cu-Al2O3梯度涂层,用电子扫描显微镜(SEM)、金相显微镜等手段对涂层进行微观组织和成分分析,用自制销盘式固定磨料磨损试验机,检测了Cu-Al2O3梯度涂层的耐磨料磨损性能.结果表明,采用等离子喷涂法制备的Cu-Al2O3梯度涂层无明显的组织突变和宏观层间界面,涂层的组织表现出宏观不均匀性和微观连续性分布特征;梯度涂层中当Al2O3含量(质量分数,%)达到80%时(GC6),涂层的耐磨性最高,约为基体的3倍,随着Al2O3含量继续增大,纯陶瓷涂层(GC7)的耐磨性有所下降.     

Study of Al2O3 coatings on AISI 316 stainless steel obtained by controlled atmosphere plasma spraying (CAPS)

The tribological behaviour of Al₂O₃ coatings on AISI 316 stainless steel, obtained by the process of controlled atmosphere plasma spraying (CAPS), is studied in this work. Atmospheric plasma spraying (APS) and high pressure plasma spraying (HPPS) were applied in order to produce these coatings. The APS coatings exhibited lower microhardness values compared to the values of HPPS coatings. Regarding the HPPS coatings it was found that plasma composition, through its heat capacity, does influence the heat transfer to particles, and, consequently, their flattening and densification process, which govern coating properties. It was revealed that tribological behaviour of coatings was influenced by the applied spraying method too. Coatings from HPPS under high-enthalpy conditions led to worst wear behaviour. In general, properties, such as microstructure, microhardness, coefficient of friction and wear resistance depended on the processing conditions such as pressure and composition of the spraying chamber atmosphere.