Al2O3弥散强化Ni-Cr合金粉的微束等离子喷涂

用行星式球磨技术制备了Al2O3弥散强化Ni-Cr合金粉末.为改善球磨后粉末的流动性,对粉末进行了喷雾造粒,并利用微束等离子喷涂(MPS)技术制备涂层.采用XRD、SEM等方法研究弥散强化粉末及其喷涂层的微观组织结构.试验结果表明,球磨加工后,Al3O3颗粒尺寸为微纳米级,并弥散分布于Ni-Cr基体粉末中.经微束等离子喷涂后,涂层结构较致密,孔隙率低(<2%).涂层经650 ℃高温耐冲蚀试验后,发现微纳米结构涂层的耐冲蚀性良好,这与Al2O3陶瓷对涂层的增韧机理有关.     

等离子喷涂Al2O3陶瓷涂层的冲蚀磨损特性

研究了在固体颗粒冲蚀条件下,不同冲击速度、不同磨料尺寸等因素对等离子喷涂Al2O3陶瓷涂层冲蚀磨损率的影响,并在不同条件下与20号钢进行了对比试验,分析了等离子喷涂Al2O3陶瓷涂层的冲蚀磨损特性及磨损机理,提出等离子喷涂Al2O3陶瓷涂层具有脆性特征的冲蚀磨损特性,它适用于细磨料低速冲蚀磨损条件.     

金属基体高温耐磨复合涂层的制备与磨损性能研究

锅炉受热面金属管壁的磨损问题是困扰电厂安全运行的一大难题.实验采用改性无机粘结剂,以耐磨性优良的SiC、Al2O3颗粒为基本骨料,辅以少量Cr2O3颗粒,再添加少量的膨润土和无机纤维为增强材料,提高涂层和基体间的结合力.在500℃下固化后得到实验涂层.分别在冲蚀角15°、25°、35°、45°、60°下研究了涂层耐冲蚀...     

超音速等离子喷涂NiCr-Cr3C2涂层的结构及冲蚀磨损机理

目的改善流体机械部件的耐冲蚀磨损性能。方法采用超音速等离子喷涂(Supersonic Plasma Spraying)系统制备NiCr-Cr_3C_2涂层,通过X射线衍射仪(XRD)分析了喷涂粉末和涂层的物相结构。采用扫描电子显微镜(SEM)及配套的能谱分析仪(EDS)观察和分析了涂层的微观形貌及化学成分。采用透射电子显微镜(TEM)从超微观角度分析了涂层的晶粒结构。采用Image J2x孔隙率计算软件测定了涂层的孔隙率。采用显微硬度仪、纳米压痕仪及万能拉伸试验机分别测定了涂层的显微硬度、弹性模量和结合强度。采用动载磨料试验机进行了冲蚀试验,冲蚀角度为90°,砂浆比为5:8,冲蚀时间为3 h。结果获得的超音速等离子喷涂Ni Cr-Cr_3C_2涂层主要含有NiCr、Cr_3C_2、Cr_7C_3等物相,至少含有单晶、纳米晶、过渡区三个区域。涂层的显微硬度值为911HV0.3,约为基体的3倍,孔隙率为1.4%,结合强度为66 MPa,弹性模量为215.3 GPa。在90°攻角下,涂层的冲蚀磨损失效以疲劳剥落磨损为主。结论用超音速等离子喷涂系统在基体表面制备的Ni Cr-Cr_3C_2涂层具有较好的耐冲蚀磨损性能。     

高速电弧喷涂Fe3Al/WC复合涂层高温冲蚀行为研究

采用自行研制的新型热喷涂Fe3Al/WC复合合金粉芯丝材,成功地用高速电弧喷技术制备出了Fe3Al金属化合物基金属陶瓷复合涂层。对涂层成分、显微组织、涂层相结构和组成进行了分析,结果表明,涂层由以Fe-26Al为主的Fe3Al基体相与约20%的WC、W2C和 a-Al2O3相组成。对比研究了Fe3Al/WC涂层和电站锅炉钢20 g从室温至650 ℃氧化环境条件下不同攻角的高温冲蚀磨损性能,结果表明Fe3Al/WC涂层的高温冲蚀磨损抗力高于20 g钢,650 ℃和30°攻角下的稳态相对冲蚀磨损抗力为20 g钢的3.14倍。温度对Fe3Al/WC涂层的冲蚀行为有较大影响：温度 < 450℃,涂层的冲蚀率变化不大,表现出塑性材料的冲蚀行为;温度 >450 ℃,涂层冲蚀率变化较大,呈现典型的脆性材料冲蚀磨损行为。并对其高温冲蚀磨损机理进行了分析。     

砂型铸造用模具快速制备及耐磨性研究

研究了砂型铸造用模具的快速制备及适合其耐磨的表面涂层材料,对添加Al2O3颗粒材料进行了耐磨性系列试验,用扫描电镜和原子力显微镜进行了分析。结果表明,当Al2O3颗粒含量达5%时,磨损率最低;随Al2O3颗粒含量的增加,复合涂层的摩擦系数逐渐增大,复合涂层的磨损机理由粘着占主导逐渐转变为犁削沟占主导。     

不同实验参数下α-Al2O3陶瓷冲蚀磨损性能研究

以冲蚀磨损工况典型应用材料Cr15Mo3高铬铸铁为对比材料,研究了不同磨粒硬度、不同磨粒粒径、不同冲邋蚀角度(0°、30°、45°、60°和90°)对α-Al2O3结构陶瓷抗冲蚀磨损性能的影响,分析了试验材料冲蚀磨损微观失效机制.结果表明:Crl5Mo3高铬铸铁冲蚀磨损体积均大于α-Al2O3陶瓷材料;随着Crl5Mo3高铬铸铁冲蚀磨损体积增加幅度最大;处于45°和60°,90°冲蚀角度时试验材料的冲蚀磨损体积损失最大;α-Al2O3陶瓷受冲蚀时切削磨损小,随着冲蚀角度增加,材料的耗能方式主要径向裂纹和横向裂纹的断裂表面能.     

过渡材料对等离子喷涂Al2O3梯度陶瓷涂层性能影响

针对Al2O3陶瓷涂层结合强度低、孔隙率高的实际,选择NiAl金属间化合物和金属铜粉作为过渡材料,利用等离子喷涂制备Al2O3梯度陶瓷涂层,并对梯度涂层进行组织形貌观察,测试结合强度和孔隙率.结果表明,梯度涂层的组织表现出宏观的不均匀性和微观连续性的分布特征,NiAl和Cu是金属基体与Al2O3涂层之间过渡层的理想材料,可以有效地提高涂层的结合强度,而Cu-Al2O3梯度涂层又比NiAl-Al2O3梯度涂层结合强度高;梯度涂层的孔隙率远低于双涂层的孔隙率,在Cu-Al2O3梯度涂层中随Al2O3含量的增加,涂层的孔隙率降低,而且孔隙率低于NiAl-Al2O3梯度涂层.     

等离子喷涂Al_2O_(3p)/NiCrBSi涂层优化设计

利用二次回归正交组合设计法优化喷涂工艺参数,建立了等离子喷涂Al2O3p/NiCrBSi复合材料涂层冲蚀磨损失重率的二次回归方程.研究了等离子喷涂参数对涂层冲蚀磨损失重率的影响.结果表明,利用Matlab软件编程计算,优化等离子喷涂参数,明显提高了涂层的抗冲蚀磨损性能.为等离子喷涂制备以氧化铝(Al2O3)颗粒增强金属基(NiCrBSi)复合材料涂层(Al2O3p/NiCrBSi)的实际应用提供必要的理论依据和技术数据.     

等离子喷涂Cu-Al2O3梯度涂层的组织与耐磨性分析

针对纯陶瓷涂层由于结合强度低、孔隙率高、影响涂层耐磨性的实际,用等离子喷涂法制备了Cu-Al2O3梯度涂层,用电子扫描显微镜(SEM)、金相显微镜等手段对涂层进行微观组织和成分分析,用自制销盘式固定磨料磨损试验机,检测了Cu-Al2O3梯度涂层的耐磨料磨损性能.结果表明,采用等离子喷涂法制备的Cu-Al2O3梯度涂层无明显的组织突变和宏观层间界面,涂层的组织表现出宏观不均匀性和微观连续性分布特征;梯度涂层中当Al2O3含量(质量分数,%)达到80%时(GC6),涂层的耐磨性最高,约为基体的3倍,随着Al2O3含量继续增大,纯陶瓷涂层(GC7)的耐磨性有所下降.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Rheology Feature of Simple Metal Melt

The rheology feature of Sb, Bi melt and alloys was studied using coaxial cylinder high-temperature viscometer. The results showed that the curve of torsion-rotational speed for Sb melt presents a linear relation in all measured temperature ranges, whereas for the Bi melt, the curve presents obvious non-Newtonian feature within the low temperature range and at relative high shear stress. The rheology feature of Sb80Bi20 and Sb20Bi80 alloy melts was well correlated with that of Sb and Bi, respectively. It is considered that the rheology behavior of Sb melt plays a crucial role in Sb80Bi20 alloy and that of Bi melt plays a crucial role in Sb20Bi80 alloy.     

Microstructures and Mechanical Properties of a Newly Developed Austenitic Heat Resistant Steel

The effect of heat treatment on the microstructures and mechanical properties of a newly developed austenitic heat resistant steel(named as T8 alloy) for ultra-supercritical applications have been studied. Results show that the main phases in the alloy after solution treatment are γ and primary MX. Subsequent aging treatment causes the precipitation of M_(23)C_6 carbides along the grain boundaries and a small number of nanoscale MX inside the grains. In addition, with increasing the aging temperature and time, the morphology of M_(23)C_6 carbides changes from semi-continuous chain to continuous network.Compared with a commercial HR3C alloy, T8 alloy has comparable tensile strength, but higher stress rupture strength. The dominant cracking mechanism of the alloy during tensile test at room temperature is transgranular, while at high temperature, intergranular cracking becomes the main cracking mode, which may be caused by the precipitation of continuous M_(23)C_6 carbides along the grain boundaries. Typical intergranular cracking is the dominant cracking mode of the alloy at all stress rupture tests.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

The 15th Global Foundry Sourcing Conference 2014held in Qingdao China

Organized by Suppliers China Co., Ltd and co-organized by the National Technical Committee 54 on Foundry of Standardization Administration of China, the 15th Global Foundry Sourcing Conference 2014 （hereinafter referred to as FSC 2014） was successfully held on Sep. 23rd in Grand Regency Hotel, Qingdao. More than 500 delegates from home and abroad attended this conference, including over 130 purchasers from 20 countries and 380 domestic and foreign suppliers.     

Secondary Recrystallization Behaviors of Grain-Oriented 6.5 wt% Silicon Steel Sheets Produced by Rolling and Nitriding Processes

By rolling and nitriding processes, 0.23- to 0.3-mm-thick grain-oriented 6.5 wt% silicon steel sheets were produced. The core losses of grain-oriented 6.5 wt% silicon steel at frequencies ranging from 400 Hz to 20 k Hz were lower than that of the grain-oriented 3 wt% silicon steel with the same thickness by 16.6–35.8%. The secondary recrystallization behavior was investigated by scanning electron microscopy, energy-dispersive spectroscopy, and electron backscattered diffraction. The results show that the secondary recrystallization in high-silicon steel sheets develops more completely as the nitrogen content increases after nitriding, secondary recrystallized grain sizes become larger, and the sharpness of Goss texture increases. Because more {110}116 grains in the subsurface and the central layer of the sheets have a lot of 20°–45° high-energy boundaries in addition to Goss grains, {110}116 can be the main component through selective growth during secondary recrystallization when the inhibitor quantity is not enough and inhibitor intensity is weaker. The increases in nitrogen content can increase the inhibitor intensity and hinder abnormal growth of a mount of {110}116 grains and therefore enhance the sharpness of Goss texture.     

Laser Cladded TiCN Coatings on the Surface of Titanium

Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs (OM). The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm / s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm - 2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2, and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80?滋m, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis