Experimental investigations on the effect of fuel injection parameters on diesel engine fuelled with biodiesel blend in diesel with hydrogen enrichment

Fuel injection pressure and injection timing are two extensive injection parameters that affect engine performance, combustion, and emissions. This study aims to improve the performance, combustion, and emissions characteristics of a diesel engine by using karanja biodiesel with a flow rate of 10 L per minute (lpm) of enriched hydrogen. In addition, the research mainly focused on the use of biodiesel with hydrogen as an alternative to diesel fuel, which is in rapidly declining demand. The experiments were carried out at a constant speed of 1500 rpm on a single-cylinder, four-stroke, direct injection diesel engine. The experiments are carried out with variable fuel injection pressure of 220, 240, and 260 bar, and injection timings of 21, 23, and 25 °CA before top dead center (bTDC). Results show that karanja biodiesel with enriched hydrogen (KB20H10) increases BTE by 4% than diesel fuel at 240 bar injection pressure and 23° CA bTDC injection timing. For blend KB20H10, the emissions of UHC, CO, and smoke opacity are 33%, 16%, and 28.7% lower than for diesel. On the other hand NOx emissions, rises by 10.3%. The optimal injection parameters for blend KB20H10 were found to be 240 bar injection pressure and 23 °CA bTDC injection timing based on the significant improvement in performance, combustion, and reduction in exhaust emissions.     

掺混比例和喷射定时对二甲醚-乙醇发动机燃烧和排放的影响

在一台电控共轨发动机上,试验研究了乙醇掺混比例和喷射定时对二甲醚-乙醇混合燃料燃烧及排放的影响。结果表明:随乙醇比例的增加,滞燃期延长,燃烧持续期缩短,最大压力升高率上升。随喷射推迟,滞燃期延长,燃烧相位延后,燃烧持续期在纯二甲醚时延长,而在掺混乙醇时则先延长后缩短,最大压力升高率先下降后上升。掺混乙醇和推迟喷射使预混燃烧比例增加。随喷射推迟,混合燃料的排气温度升高,喷射推迟到上止点后,排气温度随乙醇比例的增加而升高,排气温度高,则废气能量高,增压器增压比大,进气流量大,导致缸内压缩压力升高。在上止点前喷射时,掺混乙醇能使HC和CO排放保持在较低范围的同时,一定程度降低NO_x排放,掺混15%的乙醇较纯二甲醚最大降低约11%NO_x排放。随推迟喷射,NO_x排放降低,最大降幅达52%,在过分推迟燃料喷射时,因热效率低,循环喷射量增加,含15%乙醇混合燃料的NO_x排放会高于纯二甲醚。HC和CO排放随喷射推迟而升高,且升高幅度增大。     

Hydrogen fueled spark ignition engine with electronically controlled manifold injection: An experimental study

In this work, a single cylinder conventional spark ignition engine was converted to operate with hydrogen using the timed manifold fuel injection technique. A solenoid operated gas injector was used to inject hydrogen into the inlet manifold at the specified time. A dedicated electronic circuit developed for this work was used to control the injection timing and duration. The spark timing was set to minimum advance for best torque (MBT). The engine was operated at the wide-open throttle condition. For comparison of results, the same engine was also run on gasoline.The performance and emission characteristics with hydrogen and gasoline are compared. From the results, it is found that there is a reduction of about 20% in the peak power output of the engine when operating with hydrogen. The brake thermal efficiency with hydrogen is about 2% greater than that of gasoline. A lean limit equivalence ratio of about 0.3 could be attained with hydrogen as compared to 0.83 with gasoline. CO, CO₂ and HC emissions were negligible with hydrogen operation. However, for hydrogen operation, NO_x emission was four times higher than that of gasoline at full load power. The best ignition timing for hydrogen was much retarded when compared to gasoline. The effect of hydrogen injection pressure was also studied and no specific changes were observed. The effect of operating speed was also studied.     

直喷汽油对反应活性控制压燃负荷拓展影响的数值模拟研究

基于三维计算流体力学软件CONVERGE,通过数值模拟的方法,基于不同的燃油总量、直喷汽油量、预混汽油油量和汽柴油喷射时刻等参数,展开了缸内直喷汽油对反应活性控制压燃(RCCI)燃烧模式高负荷拓展影响的研究。结果表明:进气压力及柴油喷射时刻会影响缸内浓度分层进而影响燃烧过程,而汽油喷射时刻影响不明显;在汽油采用进气道结合缸内直喷的混合喷射策略下,增加缸内直喷汽油量可以进一步增强缸内的混合气浓度分层,延长燃烧持续期,降低缸内的最高燃烧压力和压力升高率,实现更低的燃烧温度。仿真计算结果显示:若保证碳烟和NOx排放在限值内且油耗有所降低,可将平均有效指示压力(IMEP)拓展至1.6MPa;将IMEP拓展到1.7MPa后,增加汽油的预混比例并不能提高IMEP,但对排放略有改善,相应的压力升高率和燃烧压力提高。     

Numerical investigation of water injection quantity and water injection timing on the thermodynamics,combustion and emissions in a hydrogen enriched lean-burn natural gas SI engine

Water direct injection into the cylinder is one of effective ways to suppress the combustion rate and knocking combustion in turbocharged SI engine. In this study, a detailed one-dimensional model coupled with the water direct injection was built by using the GT-Power according to the real tested hydrogen-enriched lean-burn natural gas (NG) SI engine, and validated against the experimental data. Then, a series of cases with various water injection quantity and injection timing were comprehensively investigated on the thermodynamics, combustion and emissions characteristics of the NGSI engine. The impact of the thermo-physical of the water were discussed in detailed by sweeping various water injection quantity and water injection timing. The results indicated that peak combustion pressure and peak heat release rate decreased with the increasing the water injection quantity. In addition, the 50% combustion location and peak combustion pressure location were retarded with the increasing the water injection quantity. As for the water injection timing, the peak combustion pressure and peak combustion temperature were slightly decreased with retarding the water injection timing. Apart from that, the indicated thermal efficiency decreased 4.03% and the equivalent fuel consumption increased 3.56% with injecting 60 mg water into the cylinder compared the case without water injection. Furthermore, the indicated thermal efficiency decreased 4.68% and the equivalent fuel consumption increased 4.66% by sweeping the water injection timing from the 150 CA to 50 CA before top dead center. However, the volumetric efficiency slightly ascended with increasing the water injection quantity and retarding the water injection timing. Finally, the NOx emissions declined with increasing the water injection quantity and retarding the water injection timing. However, CO emission and unburned HC emissions increased with increasing the water injection quantity and retarding the water injection timing. The main aim of this paper is expected to provide a comprehensively assessment of the thermo-physical of water on the thermodynamics, combustion, and emissions of the hydrogen enriched NGSI engine.     

Effects of second hydrogen direct injection proportion and injection timing on combustion and emission characteristics of hydrogen/n-butanol combined injection engine

Hydrogen and n-butanol are superior alternative fuels for SI engines, which show high potential in improving the combustion and emission characteristics of internal combustion engines. However, both still have disadvantages when applied individually. N-butanol fuel has poor evaporative atomization properties and high latent heat of vaporization. Burning n-butanol fuel alone can lead to incomplete combustion and lower temperature in the cylinder. Hydrogen is not easily stored and transported, and the engine is prone to backfire or detonation only using hydrogen. Therefore, this paper investigates the effects of hydrogen direct injection strategies on the combustion and emission characteristics of n-butanol/hydrogen dual-fuel engines based on n-butanol port injection/split hydrogen direct injection mode and the synergistic optimization of their characteristics. The energy of hydrogen is 20% of the total energy of the fuel in the cylinder. The experimental results show that a balance between dynamics and emission characteristics can be found using split hydrogen direct injection. Compared with the second hydrogen injection proportion (IP2) = 0, the split hydrogen direct injection can promote the formation of a stable flame kernel, shorten the flame development period and rapid combustion period, and reduce the cyclic variation. When the IP2 is 25%, 50% and 75%, the engine torque increases by 0.14%, 1.50% and 3.00% and the maximum in-cylinder pressure increases by 1.9%, 2.3% and 0.6% respectively. Compared with IP2 = 100%, HC emissions are reduced by 7.8%, 15.4% and 24.7% and NOx emissions are reduced by 16.4%, 13.8% and 7.9% respectively, when the IP2 is 25%, 50% and 75%. As second hydrogen injection timing (IT2) is advanced, CA0-10 and CA10-90 show a decreasing and then increasing trend. The maximum in-cylinder pressure rises and falls, and the engine torque gradually decreases. The CO emissions show a trend of decreasing and remaining constant. However, the trends of HC emissions and NOx emissions with IT2 are not consistent at different IP2. Considering the engine's dynamics and emission characteristics, the first hydrogen injection proportion (IP1) = 25% plus first hydrogen injection timing (IT1) = 240°CA BTDC combined with IP2 = 75% plus IT2 = 105°CA BTDC is the superior split hydrogen direct injection strategy.     

Experimental investigation on a DI dual fuel engine with hydrogen injection

Over the past two decades considerable efforts have been undertaken to develop and introduce new alternative fuels for the conventional gasoline and diesel. Many alternative fuels, both liquid and gaseous, have been experimented and some have even been commercialized such as ethanol, natural gas, etc. Hydrogen has been considered as an excellent fuel to replace the petroleum‐based fuels due to its clean burning characteristics. In the present experimental investigation, hydrogen was injected in the intake manifold and diesel fuel was injected inside the engine cylinder in the conventional manner. Hydrogen injection parameters such as injection timing, injection duration and quantity of hydrogen injected were optimized based on the performance and emission characteristics. Exhaust gas recirculation (EGR) technique was adopted to reduce the oxides of nitrogen emission. From the results it was observed that for hydrogen diesel dual fuel (DF) engine, the optimal operating parameters for hydrogen injection were start of injection at gas exchange top dead centre with injection duration of 30° crank angle with the hydrogen flow rate of 7.5 litres per minute (lpm). With EGR the optimized condition was found to be 20% for the entire load. The brake thermal efficiency with 20% EGR increases by 16% at 75% load as compared with diesel, while at full load it reduces by 8% due to the recirculation of exhaust gases that results in a reduction of intake oxygen concentration compared with part load. NO_X emission decreases by five and half times, while other emissions increase by 1.4 times as compared with DF engine. Copyright © 2008 John Wiley & Sons, Ltd.     

乙醇/汽油双燃料双直喷模式下分层稀薄燃烧试验研究

针对乙醇与汽油固定掺混比例下使用不能充分发挥乙醇燃料优势的问题,开发出了乙醇汽油双燃料-双直喷系统,并在一台点燃式单缸试验机上进行试验,研究了稀薄燃烧下3种不同的喷射策略对发动机燃烧和性能的影响。研究发现:在稀薄燃烧的情况下,随喷射时刻的推迟,不同喷射策略下动力性呈现先增长后降低的趋势。在保证喷油量不变时,有效热效率随过量空气系数增大而明显提高,当量燃油消耗率逐渐降低。随喷射时刻的推迟,热效率呈现先升高后降低的趋势。在过量空气系数为1.2,汽油喷射时刻为上止点前180°,乙醇喷射时刻为上止点前300°时,有效热效率达到最高值40.5%。此外,相比于汽油,添加乙醇燃料使得稀薄燃烧更稳定,循环波动更小。     

Experimental study of fuel stratification for HCCI high load extension

Fuel stratification has the potential to extend the high load limits of homogeneous charge compression ignition (HCCI) combustion by improving the control over the combustion phase as well as reducing the maximum rate of pressure rise. In this work, experiments were carried out on a single-cylinder engine equipped with a dual-fuel-injection system – a port injector for preparing a homogeneous charge and a direct in-cylinder injector for creating the desired fuel stratification. The homogeneous charge was prepared using gasoline fuel while the fuel stratification was created with the in-cylinder injection of either gasoline or methanol during the compression stroke. The test results indicate that high load extension using gasoline for fuel stratification is limited by the trade-off between CO and NO_x emissions. Weak gasoline stratification leads to an advanced combustion phase and an increase in NO_x emission, while increasing the stratification with a higher quantity of gasoline direct injection, results in a significant deterioration in both the combustion efficiency and the CO emission. Engine tests using methanol for the stratification retarded the ignition timing and prolonged the combustion duration, resulting in a substantial reduction in the maximum rate of pressure rise and the maximum cylinder pressure – a prerequisite for HCCI high load extension. Further tests were then conducted with methanol stratification to extend the HCCI load limit and to optimize the stratified methanol-to-gasoline fuel ratio. Compared to gasoline HCCI, a 50% increase in the maximum IMEP attained was achieved with an acceptable maximum pressure rise rate of 0.5 MPa/°CA while maintaining a high thermal efficiency.     

Performance and emission study in manifold hydrogen injection with diesel as an ignition source for different start of injection

Over the past two decades there has been a considerable effort to develop and introduce alternative transportation fuels to replace conventional fuels, gasoline and diesel. Environmental issues are the principal driving forces behind this effort. To date the bulk of research has focused on the carbon-based fuels such as reformulated gasoline, methanol and natural gas. One alternative fuel to carbon-based fuels is hydrogen which is considered to be low polluting fuel. In the present experimental investigation hydrogen was injected into the intake manifold by using an injector. Using an electronic control unit (ECU) the injection timing and the duration were controlled. From the results it is observed that the optimum injection timing is at gas exchange top dead center (GTDC). The efficiency improved by about 15% with an increase in NO_X emission by 3% compared to diesel. The smoke emission decreased by almost 100%. A net reduction in carbon emissions was also noticed due to the use of hydrogen. By adopting manifold injection technique the hydrogen–diesel dual fuel engine operates smoothly with a significant improvement in performance and reduction in emissions.     

An experimental investigation on manifold‐injected hydrogen as a dual fuel for diesel engine system with different injection duration

Stringent emission norms and rapid depletion of petroleum resources have resulted in a continuous effort to search for alternative fuels. Hydrogen is one of the best alternatives for conventional fuels. Hydrogen has both the benefits and limitation to be used as a fuel in an automotive engine system. In the present investigation, hydrogen was injected into the intake manifold by using a hydrogen gas injector and diesel was introduced in the conventional, mode which also acts as an ignition source for hydrogen combustion. The flow rate of hydrogen was set at 5.5 l min^?1 at all the load conditions. The injection timing was kept constant at top dead center (TDC) and injection duration was adjusted to find the optimized injection condition. Experiments were conducted on a single cylinder, four stroke, water‐cooled, direct injection diesel engine coupled to an electrical generator. At 75% load the maximum brake thermal efficiency for hydrogen operation at injection timing of TDC and with injection duration of 30°CA is 25.66% compared with 21.59% for diesel. The oxides of nitrogen (NO_X) emission are 21.7 g kWh^?1 for hydrogen compared with diesel of 17.9 g k Wh^?1. Smoke emissions reduced to 1 Bosch smoke number (BSN) in hydrogen compared with diesel of 2.2 BSN. Hydrogen operation in the dual fuel mode with diesel exhibits a better performance and reduction in emissions compared with diesel in the entire load spectra. Copyright © 2009 John Wiley & Sons, Ltd.     

Influence of advanced injection timing on the performance and emissions of CI engine fueled with ethanol‐blended diesel fuel

Ethanol has been considered as an alternative fuel for diesel engines. On the other hand, injection timing is a major parameter that sensitively affects the engine performance and emissions. Therefore, in this study, the influence of advanced injection timing on the engine performance and exhaust emissions of a single cylinder, naturally aspirated, four stroke, direct injection diesel engine has been experimentally investigated when using ethanol‐blended diesel fuel from 0 to 15% with an increment of 5%. The original injection timing of the engine is 27° crank angle (CA) before top dead center (BTDC). The tests were conducted at three different injection timings (27, 30 and 33° CA BTDC) for 30 Nm constant load at 1800 rpm. The experimental results showed that brake‐specific energy consumption (BSEC), brake‐specific fuel consumption (BSFC), NO_x and CO₂ emissions increased as brake‐thermal efficiency (BTE), smoke, CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. Comparing the results with those of original injection timing, NO_x emissions increased and smoke, HC and CO emissions decreased for all test fuels at the advanced injection timings. For BSEC, BSFC and BTE, advanced injection timings gave negative results for all test conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

A coupling dynamics and thermodynamics study of diesel pilot-ignition injection effect on hydrogen combustion of a linear engine

Linear hydrogen engine is a new type of energy conversion device to supports variable compression ratio operation for clean emission. However, the new hydrogen engine using conventional spark ignition shows slow combustion speed and low thermal efficiency. This study makes a preliminary assessment to discuss the application of diesel pilot-ignition technology in linear hydrogen engine aiming to accelerate combustion and improve efficiency. A new coupling model between dynamics and thermodynamics is proposed and then iteratively calculated to give insight the interrelationship of combustion and motion in a diesel pilot-ignited linear hydrogen engine, while the effect of injection position on the hydrogen engine combustion is also investigated to make clear the feasibility of combustion optimization. The results indicate that the linear hydrogen engine is speeded by properly advancing the injection to promote combustion, and it has a positive effect on in-cylinder gas temperature, pressure and pressure rise rate, unless the injection is too early which results in higher NO emissions and aggravate the working intensity of the engine. In addition, the closer the fuel injection is to the top dead center, the incomplete combustion of hydrogen and diesel in the cylinder, the decrease of engine fuel economy and the increase of soot emissions. There is an optimal thermal efficiency of 40.7% for the LHE when it operates in the 0.8 mm injection position condition.     

Emission and performance estimation in hydrogen injection strategies on diesel engines

Recently, the increasing demand for energy requires the use of alternative fuels, especially in fossil fueled power systems. As a promising alternative fuel for next-generation diesel engines that utilize fossil fuel, hydrogen fuel is one step ahead due to its positive properties. In this study, the effects of hydrogen on the performance of a diesel engine have been numerically investigated with respect to different injection ratios and timings. The numerical results of the study for 25% load conditions on a single-cylinder, four-stroke diesel engine have been validated against experimental data taken from literature and good agreement has been observed for pressure results. Emission parameters such as NO_x, CO and performance parameters such as cylinder temperature, pressure, power, thermal efficiency and IMEP are presented comparatively.The results of numerical analyses show that the maximum pressure, temperature and heat release rate are observed with injection ratio of H15 and early injection timing (20° CA BTDC). Besides that, engine power, thermal efficiency and IMEP are greatly improved with increasing injection ratio and early injection timing. Although combustion chamber performance parameters improve with rising the hydrogen injection ratio, higher NO_x emissions have also been detected as a negative side effect. Furthermore, while early injection timing increases diesel engine performance, it also causes an increase in NO_x emissions. Therefore, precise determination of injection timing together with the optimum amount of hydrogen has revealed that it brings crucial improvement in engine performance and emissions.     

负阀重叠早喷模式HCCI燃烧数学模型与计算分析

针对早喷模式中的排气上止点燃油喷射(ETCI)模式,综合广安博之模型、Bai模型的优点加以改进,并将空间均质燃烧与油膜蒸发燃烧相耦合,建立了一种新型的基于喷雾、燃油附壁、油膜蒸发、燃烧等一系列过程适用于缸内早喷模式的数学模型。利用该模型对135单缸柴油机ETCI燃烧模式进行校核计算,并通过试验验证进一步对燃烧过程中的工况参数及调节参数进行了研究。研究结果表明:在ETCI模式下,存在部分油膜附壁,油膜的蒸发主要与缸内的气体温度与壁温有关,且存在明显的两阶段加热过程。累积放热率与排气门关闭时刻和壁温基本呈线性关系,排气门关闭时刻提前10°CA,累积放热率上升约6%;壁温升高50K,累积放热率上升4%。增压压力升高,累积放热率降低,增压压力越大,累积放热率降低的幅度越小。     

用汽油和甲醇燃油分层拓展HCCI燃烧高负荷的试验研究

在一台单缸HCCI发动机上研究了进气道喷射汽油缸内喷射甲醇形成汽油甲醇燃油分层的HCCI燃烧排放特性,探索了其拓展HCCI燃烧高负荷的潜力。试验结果表明:在汽油HCCI燃烧中喷射甲醇能够有效降低缸内混合气的温度,推迟着火时刻,延长燃烧持续期,从而降低压力升高率和缸内最高燃烧压力,有利于拓展HCCI燃烧高负荷。一定的HCCI负荷工况存在最佳的汽油甲醇比例,且汽油甲醇最佳比例随着负荷的增加不断减小。在最大压力升高率0.5MPa/°CA和较高的指示效率的限制下,自然吸气条件下采用汽油和甲醇燃油分层的HCCI燃烧最高负荷比汽油HCCI燃烧提高了近50%,达到0.62MPa。     

二次燃油喷射对摩托车汽油机性能影响的试验研究

利用发动机台架试验,对二次燃油喷射技术在摩托车汽油机上的应用进行了研究。结果表明:进气道喷射式摩托车汽油机存在附壁油膜以液体形式进入气缸的现象。发动机性能与附壁油膜挥发量有直接关系,节气门开度较小时,喷油时刻推迟将导致附壁油膜挥发时间变短,从而减少附壁油膜挥发量,使发动机的功率下降、排放恶化;节气门开度较大时,机体温度较高、进气流速较大,改变喷油时刻对发动机动力及排放性能基本无影响;膨胀冲程喷射燃油所占比例较大时,附壁油膜挥发量较大,发动机动力性能较好。     

Study on combustion and emission characteristics of a n-butanol engine with hydrogen direct injection under lean burn conditions

The n-butanol fuel, as a renewable and clean biofuel, could ease the energy crisis and decrease the harmful emissions. As another clean and renewable energy, hydrogen properly offset the high HC emissions and the insufficient of dynamic property of pure n-butanol fuel in SI engines, because of the high diffusion coefficient, high adiabatic flame velocity and low heat value. Hydrogen direct injection not only avoids backfire and lower intake efficiency but also promotes to form in-cylinder stratified mixture, which is helpful to enhance combustion and reduce emissions. This experimental study focused on the combustion and emissions characteristics of a hydrogen direct injection stratified n-butanol engine. Three different hydrogen addition fractions (0%, 2.5%, 5%) were used under five different spark timing (10° ,15° ,20° ,25° ,30° CA BTDC). Engine speed and excess air ratio stabled at 1500 rpm and 1.2 respectively. The direct injection timing of the hydrogen was optimized to form a beter stratified mixture. The obtained results demonstrated that brake power and brake thermal efficiency are increased by addition hydrogen directly injected. The BSFC is decreased with the addition of hydrogen. The peak cylinder pressure and the instantaneous heat release rate raises with the increase of the hydrogen addition fraction. In addition, the HC and CO emissions drop while the NOx emissions sharply rise with the addition of hydrogen. As a whole, with hydrogen direct injection, the power and fuel economy performance of n-butanol engine are markedly improved, harmful emissions are partly decreased.     

不同喷油压力对汽油压燃中高负荷性能试验研究

基于一台改装后的压缩比为17的压燃式单缸发动机,展开不同喷油压力对汽油压燃燃烧模式发动机燃烧特性、爆震特性、效率特性和排放特性的研究,结果表明随着喷油压力的增加,缸内混合气形成速度加快,混合气着火时刻提前,燃烧持续期缩短,热效率呈现出先增大后略微降低的趋势。喷油压力的增加使得发动机爆震趋势增强,为降低最大压力升高率和爆震强度,采用推迟喷油策略,但高喷油压力下缸内燃烧对喷油时刻变得敏感,易产生较大的平均指示压力循环波动或爆震,燃烧控制难度增加。对不同喷油压力下爆震循环的缸压信号进行分析得出喷油压力对爆震频率无明显影响。喷油压力升高会使得未燃碳氢和CO排放降低,但同时也会使得NO_x排放增加。     

Effect of pilot fuel injection pressure and injection timing on combustion,performance and emission of hydrogen-biodiesel dual fuel engine

The present study highlights the influence of fuel injection pressure (FIP) and fuel injection timing (FIT) of Jatropha biodiesel as pilot fuel on the performance, combustion and emission of a hydrogen dual fuel engine. The hydrogen flow rates used in this study are 5lit/min, 7lit/min, and 9lit/min. The pilot fuel is injected at three FIPs (500, 1000, and 1500 bar) and at three FITs (5°, 11°, and 17?bTDC). The results showed an increase in brake thermal efficiency (B_th)from 25.02% for base diesel operation to 32.15% for hydrogen-biodiesel dual fuel operation with 9lit/min flow rate at a FIP of 1500 bar and a FITof17?bTDC. The cylinder pressure and heat release rate (HRR) are also found to be higher for higher FIPs. Advancement in FIT is found to promote superior HRR for hydrogen dual fuel operations. The unburned hydrocarbon (UHC) and soot emissions are found to reduce by 59.52% and 46.15%, respectively, for hydrogen dual fuel operation with 9lit/min flow rate at a FIP of 1500 bar and a FIT of 11?bTDC. However, it is also observed that the oxides of nitrogen (NO_X) emissions are increased by 20.61% with 9lit/min hydrogen flow rate at a FIP of 1500 bar and a FIT of 17?bTDC. Thus, this study has shown the potential of higher FIP and FIT in improving the performance, combustion and emission of a hydrogen dual fuel engine with Jatropha biodiesel as pilot fuel.