Estimation of plasma density perturbation from dusty plasma injection by laser irradiation on tungsten target in DiPS

To investigate the interaction of dusty plasma with magnetized plasmas at divertor plasma simulator, radial profiles of plasma density(ne) and electron temperature were measured in terms of plasma discharge currents and magnetic flux intensity by using a fast scanning probes system with triple tips. Dusty plasma with dusts(a generation rate of 3 μg s~(-1) and a size of 1–10 μm)was produced via interactions between a high-power laser beam and a full tungsten target. As ne increases, the scale of the effects of dusty plasma injection on magnetized plasmas was decreased. Also, the duration of transient fluctuation was reduced. For numerical estimation of plasma density perturbation due to dusty plasma injection, the result was ~10% at a core region of the magnetized plasma with n_e of(2–5)×10~(11) cm~(-3) at steady state condition.     

Experimental investigation on the evolution of plasma properties in the discharge channel of a pulsed plasma thruster

Pulsed plasma thrusters(PPTs) are an attractive form of micro-thrusters due to advantages such as their compactness and lightweight design compared to other electric propulsion systems.Experimental investigations on their plasma properties are beneficial in clarifying the complex process of plasma evolution during the micro-second pulse discharge of a PPT. In this work, the multi-dimensional evolutions of the light intensity of the PPT plasma with wavelength, time, and position were identified. The plasma pressure was obtained using an iterative process with composition calculations. The results show that significant ion recombination occurred in the discharge channel since the line intensities of CII, CIII, CIV, and FII decreased and those of CI and FI increased as the plasma moved downstream. At the center of the discharge channel, the electron temperature and electron density were in the order of 10 000 K and 10~(17) cm~(-3),respectively. These had maximum values of 13 750 K and 2.3?×?10~(17) cm~(-3) and the maximum temperature occurred during the first half-cycle while the maximum number density was measured during the second half-cycle. The estimated plasma pressure was in the order of 10~5 Pa and exhibited a maximum value of 2.69?×?10~5 Pa.     

Time-Resolved Emission Spectroscopic Study of Laser-Induced Steel Plasmas

Laser-induced steel plasma is generated by focusing a Q-switched Nd:YAG visible laser(532 nm wavelength) with an irradiance of 1 x 109 W/cm2 on a steel sample in air at atmospheric pressure.An Echelle spectrograph coupled with a gateable intensified charge-coupled detector is used to record the plasma emissions.Using time-resolved spectroscopic measurements of the plasma emissions,the temperature and electron number density of the steel plasma are determined for many times of the detector delay.The validity of the assumption by the spectroscopic methods that the laser-induced plasma(LIP) is optically thin and is also in local thermodynamic equilibrium(LTE) has been evaluated for many delay times.From the temporal evolution of the intensity ratio of two Fe I lines and matching it with its theoretical value,the delay times where the plasma is optically thin and is also in LTE are found to be 800 ns,900 ns and 1000 ns.     

Time-Resolved Optical Emission Spectroscopy Diagnosis of CO2 Laser-Produced SnO2 Plasma

The spectral emission and plasma parameters of SnO_2 plasmas have been investigated.A planar ceramic SnO_2 target was irradiated by a CO2 laser with a full width at half maximum of 80 ns.The temporal behavior of the specific emission lines from the SnO_2 plasma was characterized.The intensities of Sn I and Sn II lines first increased,and then decreased with the delay time.The results also showed a faster decay of Sn I atoms than that of Sn II ionic species.The temporal evolutions of the SnO_2 plasma parameters(electron temperature and density) were deduced.The measured temperature and density of SnO_2 plasma are 4.38 eV to0.5 eV and 11.38×10~(17) cm~(-3) to 1.1×10~(17) cm~(-3),for delay times between 0.1 μs and 2.2 μs.We also investigated the effect of the laser pulse energy on SnO_2 plasma.     

Spectral Characteristics of Laser-Induced Graphite Plasma in Ambient Air

An experimental setup of laser-induced graphite plasma was built and the spectral characteristics and properties of graphite plasma were studied. From the temporal behavior of graphite plasma, the duration of CN partials(B~2∑~+→X~2∑~+) emission was two times longer than that of atomic carbon, and all intensities reached the maximum during the early stage from0.2 μs to 0.8 μs. The electron temperature decreased from 11807 K to 8755 K, the vibration temperature decreased from 8973 K to 6472 K, and the rotational temperature decreased from7288 K to 4491 K with the delay time, respectively. The effect of the laser energy was also studied, and it was found that the thresholds and spectral characteristics of CN molecular and C atomic spectroscopy presented great differences. At lower laser energies, the electron excited temperature, the electron density, the vibrational temperature and rotational temperature of CN partials increased rapidly. At higher laser energies, the increasing of electron excited temperature and electron density slow down, and the vibrational temperature and rotational temperature even trend to saturation due to plasma shielding and dissociation of CN molecules. The relationship among the three kinds of temperatures was T_(elec)T_(vib)T_(rot) at the same time. The electron density of the graphite plasma was in the order of 10~(17)cm~(-3) and 10~(18)cm~(-3).     

Numerical study on the modulation of THz wave propagation by collisional microplasma photonic crystal

In order to demonstrate the modulation of terahertz wave propagation in atmospheric pressure microplasmas, in this work, the band structure and the transmission characteristics of a onedimensional collisional microplasma photonic crystal are investigated, using the transfer matrix method. For a lattice constant of 150 μm and a plasma width of 100 μm, three stopbands of microplasma photonic crystal are observed, in a frequency range of 0.1–5 THz. Firstly, an increase in gas pressure leads to a decrease in the central frequency of the stopband. When the gas pressure increases from 50.5 kPa to 202 kPa, the transmission coefficient of the THz wave first increases and then decreases at high frequency, where the wave frequency is much greater than both the plasma frequency and the collision frequency. Secondly, it is interesting to find that the central frequency and the bandwidth of the first THz stopband remain almost unchanged for electron densities of less than 10¹⁵ cm^–3, increasing significantly when the electron density increases up to 10¹⁶ cm^–3. A central frequency shift of 110 GHz, and a bandgap broadening of 200 GHz in the first stopband are observed. In addition, an atmospheric pressure microplasma with the electron density of 1 × 10¹⁵–6 × 10¹⁵ cm^–3 is recommended for the modulation of THz wave propagation by plasma photonic crystals.     

Inactivation of Staphylococcus aureus by the synergistic action of charged and reactive plasma particles

In this paper, a low-pressure capacitively coupled plasma discharge sustained in an argonoxygen mixture was studied in order to evaluate its properties in terms of inactivation of Staphylococcus aureus. The plasma parameters as electron temperature and plasma density were measured by the Langmuir probe (N_e ≈ 10¹⁵ m⁻³, T_e ≈ 1.5 eV), while the neutral atom density was in the range of 10²¹ m⁻³. In the plasma phase, oxygen radicals were taken as reference of the reactive species with antimicrobial activity, and oxygen spectral lines, over a range of plasma process parameters, were investigated by the optical emission spectroscopy. Optimal plasma conditions were found, and a count reduction of 4 log in a few minutes of the bacterium proves the potentiality of an industrial grade plasma reactor as a sterilization agent.     

Effect of N_2 and O_2 on OH radical production in an atmospheric helium microwave plasma jet

UV-pulsed laser cavity ringdown spectroscopy of the hydroxyl radical OH(A–X)(0–0)band in the wavelength range of 306–310 nm was employed to determine absolute number densities of OH in the atmospheric helium plasma jets generated by a 2.45 GHz microwave plasma source.The effect of the addition of molecular gases N_2 and O_2 to He plasma jets on OH generation was studied.Optical emission spectroscopy was simultaneously employed to monitor reactive plasma species.Stark broadening of the hydrogen Balmer emission line(H_β)was used to estimate the electron density nein the jets.For both He/N_2 and He/O_2 jets, newas estimated to be on the order of 10~(15)cm~(-3).The effects of plasma power and gas flow rate were also studied.With increase in N_2 and O_2 flow rates, netended to decrease.Gas temperature in the He/O_2 plasma jets was elevated compared to the temperatures in the pure He and He/N_2 plasma jets.The highest OH densities in the He/N_2 and He/O_2 plasma jets were determined to be 1.0?×10~(16)molecules/cm~3 at x?=?4 mm(from the jet orifice)and 1.8?×?10~(16)molecules/cm~3 at x=3 mm, respectively.Electron impact dissociation of water and water ion dissociative recombination were the dominant reaction pathways, respectively, for OH formation within the jet column and in the downstream and far downstream regions.The presence of strong emissions of the N_2~+ bands in both He/N_2 and He/O_2 plasma jets, as against the absence of the N_2~+ emissions in the Ar plasma jets, suggests that the Penning ionization process is a key reaction channel leading to the formation of N_2~+ in these He plasma jets.     

Preliminary results of optical emission spectroscopy by line ratio method in the RF negative ion source at ASIPP

Optical emission spectroscopy (OES) using the trace rare gases of Ar and Xe have been carried out in a radio frequency (RF) driven negative ion source at Institute of Plasma Physics, Chinese Academy of Science (ASIPP), in order to determine the electron temperature and density of the hydrogen plasma. The line-ratio methods based on population models are applied to describe the radiation process of the excited state particles and establish their relations with the plasma parameters. The spectral lines from the argon and xenon excited state atoms with the wavelength of 750.4 and 828.0 nm are used to calculate the electron temperature based on the corona model. The argon ions emission lines with the wavelength of 480 and 488 nm are selected to calculate the electron density based on the collisional radiative model. OES has given the preliminary results of the electron temperature and density by varying the discharge gas pressure and RF power. According to the experimental results, the typical plasma parameters is T_e ≈ 2–4 eV and n_e ≈ 1×10 ¹⁷– 8×10¹⁷ m⁻³ in front of plasma grid.     

Laser-driven pulsed emission and plasma formation of Cs3Sb photocathodes

The experimental progress of laser-driven Cs₃Sb photocathodes is reported. The cathodes prepared in an UHV system can be used to generate short-pulsed, high-brightness electron beams. Emission properties are tested under a 50–200 ns pulsed Xe⁺ laser illumination. The quantum efficiency in the range of 2–5.6% and current density of 108 A/cm² are obtained. A brightness of 1.85 × 10⁹ A/m² rad² is also measured. Mass analysis and other methods have been used for investigating the plasma formation when laser intensity rises above the “break-down” threshold. The current density increases rapidly during the plasma electron emission, but the pulse width of the emission is enlarged, and the brightness is limited. It is observed that the plasma is just composed of cesium and antimony atoms from the cathode rather than adsorbed residual gases.     

Bright γ-ray source with large orbital angular momentum from the laser near-critical-plasma interaction

We propose a new laser-plasma-based method to generate bright γ-rays carrying large orbital angular momentum by interacting a circularly polarized Laguerre–Gaussian laser pulse with a near-critical hydrogen plasma confined in an over-dense solid tube. In the first stage of the interaction, it is found via fully relativistic three-dimensional particle-in-cell simulations that high-energy helical electron beams with large orbital angular momentum are generated. In the second stage, this electron beam interacts with the laser pulse reflected from the plasma disc behind the solid tube, and helical γ beams are generated with the same topological structure as the electron beams. The results show that the electrons receive angular momentum from the drive laser, which can be further transferred to the γ photons during the interaction. The γ beam orbital angular momentum is strongly dependent on the laser topological charge l and laser intensity a0, which scales as ${L}_{\gamma }\propto {a}_{0}^{4}$. A short (duration of 5 fs) isolated helical γ beam with an angular momentum of −3.3 × 10⁻¹⁴ kg m² s⁻¹ is generated using the Laguerre–Gaussian laser pulse with l = 2. The peak brightness of the helical γ beam reaches 1.22 × 10²⁴ photons s⁻¹ mm⁻² mrad⁻² per 0.1% BW (at 10 MeV), and the laser-to-γ-ray angular momentum conversion rate is approximately 2.1%.     

Investigation on the characteristics of an atmospheric-pressure microplasma plume confined inside a long capillary tube

An atmospheric-pressure microplasma plume of diameter 10 μm is generated inside a long tube. The length of the microplasma plume reaches as much as 2 cm. First, with the assistance of an air dielectric barrier discharge (DBD), the ignition voltage of the microplasma decreases from 40 kV to 23.6 kV. Second, although the current density reaches as high as (1.2−7.6)×10⁴ A cm ⁻² , comparable to the current density in transient spark discharge, the microplasma plume is non- thermal. Third, it is interesting to observe that the amplitude of the discharge current in a positive cycle of applied voltage is much lower than that in a negative cycle of applied voltage. Fourth, the electron density measured by the Stark broadening of Ar spectral line 696.5nm reaches as high as 3×10¹⁶ cm⁻³ , which yields a conductivity of the microplasma column of around 48 S m⁻¹ . In addition, the propagation velocity of the microplasma plume, obtained from light signals at different axial positions, ranges from 1×10⁵ m s ⁻¹ to 5×10 ⁵ m s⁻¹ . A detailed analysis reveals that the surface charges deposited on the inner wall exert significant influence on the discharge behavior of the microplasma.     

Heavy-ion-induced luminescence of amorphous SiO2 during nanoparticle formation

Silica glass was implanted with negative 60 keV Cu ions at an ion flux from 5 to 75 μA/cm² up to a fluence of 1 × 10¹⁷ ions/cm² at initial sample temperatures of 300, 573 and 773 K. Spectra of ion-induced photon emission (IIPE) were collected in situ in the range from 250 to 850 nm. Optical absorption spectra of implanted specimens were ex situ measured in the range from 190 to 2500 nm.

IIPE spectra showed a broad band centered around 560 nm (2.2 eV) that was assigned to Cu⁺ solutes. The band appeared at the onset of irradiation, increased in intensity up to a fluence of about 5 × 10¹⁵ ions/cm² and then gradually decreased indicating three stage of the ion beam synthesis of nanoclusters: accumulation of implants, nucleation and growth nanoclusters. The IIPE intensity normalized on the ion flux is independent on the ion flux below 20 μA/cm²at higher fluences. The intensity of the band increased with increasing samples temperature, when optical absorption spectra reveal the increase of Cu nanoparticles size.     

Development of a combined interferometer using millimeter wave solid state source and a far infrared laser on ENN's XuanLong-50 (EXL-50)

A millimeter wave solid state source—far infrared laser combined interferometer system (MFCI) consisting of a three-channel 890 GHz hydrogen cyanide (HCN) laser interferometer and a three-channel 340 GHz solid state source interferometer (SSI) is developed for real-time line-integrated electron density feedback and electron density profile of the EXL-50 spherical tokamak device. The interferometer system is a Mach–Zehnder type, with all probe-channels measured vertically, covering the plasma magnetic axis to the outermost closed magnetic plane. The HCN laser interferometer uses an HCN laser with a frequency of 890 GHz as a light source and modulates a 100 kHz beat signal by a rotating grating, giving a temporal resolution of 10 μs. The SSI uses two independent 340 GHz solid-state diode sources as the light source, the frequency of the two sources is adjustable, and the temporal resolution of SSI can reach 1 μs by setting the frequency difference of the two lasers at 1 MHz. The main optical path of the two interferometers is compactly installed on a set of double-layer optical platform directly below EXL-50. Dual optical path design using corner cube reflectors avoids the large support structures. Collinear the probe-beams of two wavelengths, then the phase error caused by vibration can be compensated. At present, the phase noise of the HCN Interferometer is 0.08 rad, corresponding to a line-integrated electron density of 0.88 × 10¹⁷ m⁻², one channel of measuring result was obtained by the MFCI system, and the highest density measured is about 0.7 × 1019 m⁻².     

A low power 50 Hz argon plasma for surface modification of polytetrafluoroethylene

The characteristics of a low power 50 Hz argon plasma for surface treatment of polytetrafluoroethylene (PTFE) film is presented in this article. The current–voltage behavior of the discharge and time-varying intensity of the discharge showed that a DC glow discharge was generated in reversed polarity at every half-cycle. At discharge power between 0.5 and 1 W, the measured electron temperature and density were 2–3 eV and ∼10⁸ cm⁻³, respectively. The optical emission spectrum of the argon plasma showed presence of some 'impurity species' such as OH, N₂ and H, which presumably originated from the residual air in the discharge chamber. On exposure of PTFE films to the argon glow plasma at pressure 120 Pa and discharge power 0.5 to 1 W, the water contact angle reduced by 4% to 20% from the original 114° at pristine condition, which confirms improvement of its surface wettability. The increase in wettability was attributed to incorporation of oxygen-containing functional groups on the treated surface and concomitant reduction in fluorine as revealed by the XPS analysis and increase in surface roughness analyzed from the atomic force micrographs. Ageing upon storage in ambient air showed retention of the induced increase in surface wettability.     

Plasma diagnostics by optical emission spectroscopy on manganese ore in conjunction with XRD,XRF and SEM-EDS

Manganese (Mn) is an important industrial mineral. Information about the chemical and phase constitution along with the concentration of impurities presented in Mn ore is compulsory in assessing its suitability for different applications. We performed the qualitative and quantitative analysis of low-grade Mn ore (LGMO) using laser-induced breakdown spectroscopy (LIBS) in conjunction with x-ray diffraction (XRD), x-ray fluorescence (XRF) and scanning electron microscopy (SEM) coupled with energy dispersive x-ray electron spectroscopy (EDS). The optical emission spectra of the LGMO sample displayed the presence of Mn, Si, Ca, Fe, Al, Mg, V, Ti, Sr, Ni, Na, Ba and Li. The plasma parameters, electron temperature and number density were estimated using the Boltzmann plot and Stark broadening line profile methods and were found to be 7500 K±750 K and 8.18±0.8×10¹⁷ cm⁻³, respectively. Quantitative analysis was performed using the calibration-free LIBS (CF-LIBS) method and its outcome along with XRD, XRF and SEM-EDS data showed almost analogous elemental composition, while the LIBS method gave acceptably precise elemental analysis by detecting the low atomic number element Li besides V and Sr. The results obtained using LIBS for the LGMO exhibited its ability as a powerful analytical tool and XRF, XRD and SEM-EDS as complementary methods for the compositional analysis of complex low-grade mineral ore.     

Effect of Si implantation on the microstructure of silicon nanocrystals and surrounding SiO2 layer

Si nanocrystals (Si-nc) embedded in a SiO₂ layer have been characterized by means of transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). For local Si concentration in excess  8 × 10²¹ Si⁺/cm³, the size of the Si-nc was found to be 3 nm and comparatively homogeneous throughout the whole implanted layer. For local Si concentration in excess of 2.4 × 10²² Si⁺/cm³, the Si-nc diameter ranges from 2 to 12 nm in the sample, the Si-nc in the middle region of the implanted layer being bigger than those near the surface and the bottom of the layer. Also, Si-nc are visible deeper than the implanted depth. Characterization by XPS shows that a large quantity of oxygen was depleted from the first 25 nm in this sample (also visible on TEM image) and most of the SiO₂ bonds have been replaced by Si–O bonds. Experimental and simulation results suggest that a local Si concentration in excess of 3 × 10²¹ Si/cm³ is required for the production of Si-nc.     

Real-time evolution of ion–surface interactions of MgAl2O3 and LiNbO3 detected by ion-induced photon spectroscopy

Ion-induced photon emission under 60 keV Cu⁻ implantation into the insulators of MgAl₂O₄ and LiNbO₃ was in situ measured over a wide wavelength range from 200 to 900 nm. The formation of the Mg and Li deficient layers for the respective insulator was detected based on the dose dependence of the Al, Mg and Li atomic line intensities. The Al I and Mg I line intensities from spinel exhibit different behaviors depending on irradiation temperatures: they gradually decrease while the (Al I)/(Mg I) ratio increases up to dose of 3×10¹⁷ ions/cm² at room temperature or exhibits a steady-state tendency at high temperature. Sharp decrease of Li I line intensity from LiNbO₃ under high dose rate bombardment indicates drastic changes of surface layer that may alter the phase stability and optical performance of insulators.     

GaAs基β辐射伏特效应微电池的参量优化设计研究

考虑放射性同位素源自吸收效应,提出基于半导体材料GaAs和同位素源⁶³Ni的微电池最优化设计方案,并通过蒙特卡罗程序MCNP模拟计算β粒子在半导体材料中的输运过程,对同位素源与半导体材料的厚度,换能单元PN结结深、耗尽区宽度、掺杂浓度、少子扩散长度,及电子空穴对的产生及收集情况等进行了研究和分析,给出了不同结深下,各物理参量的最佳设计值。在源活度为3.7×10⁷ Bq,PN结表面积为0.01 cm²时,提出的辐射伏特效应微电池最优化设计方案可实现：短路电流密度为379.68 nA/cm²,开路电压为1.375 V,填充因子为84.39%, 最大输出功率为440.4 nW/cm²,能量转化率为4.34%。     

Pulse-burst laser-based 10kHz Thomson scattering measurements

Thomson scattering(TS),as a popular and reliable diagnostic technique,has successfully measured electron temperatures and electron number densities of plasmas for many years.However,conventional TS techniques using Nd:YAG lasers operate only at tens of hertz.Here,we present the development of a high-repetition-rate TS instrument based on a high-speed,pulse-burst laser system to greatly increase the temporal resolution of measurements.Successful instrument prototype testing was carried out by collecting TS light from laboratory helium and argon plasmas at 10 kHz.Calibration of the instrument detection sensitivity using nitrogen/oxygen rotational Raman scattering signal is also presented.Quantitative electron number densities and electron temperatures of the plasma were acquired at 10 kHz,for stable plasma discharges as,respectively,～0.9 eV and ～5.37×10~(21)m~(-3) for the argon plasma,and ～1eV and ～6.5×1021 m~(-3) for the helium plasma.