Quantitative Determination of Density of Ground State Atomic Oxygen from Both TALIF and Emission Spectroscopy in Hot Air Plasma Generated by Microwave Resonant Cavity

Two experimental techniques have been used to quantify the atomic oxygen density in the case of hot air plasma generated by a microwave (MW) resonant cavity. The latter operates at a frequency of 2.45 GHz inside a cell of gas conditioning at a pressure of 600 mbar, an injected air flow of 12 L/min and an input MW power of 1 kW. The first technique is based on the standard two photon absorption laser induced fluorescence (TALIF) using xenon for calibration but applied for the first time in the present post discharge hot air plasma column having a temperature of about 4500 K near the axis of the nozzle. The second diagnostic technique is an actinometry method based on optical emission spectroscopy (OES). In this case, we compared the spectra intensities of a specific atomic oxygen line (844 nm) and the closest wavelength xenon line (823 nm). The two lines need to be collected under absolutely the same spectroscopic parameters. The xenon emission is due to the addition of a small proportion of xenon (1% Xe) of this chemically inert gas inside the air while a further small quantity of H₂ (2%) is also added in the mixture in order to collect OH(A¬X) and NH(A-X) spectra without noise. The latter molecular spectra are required to estimate gas and excitation temperatures. Optical emission spectroscopy measurements, at for instance the position z=12 mm on the axis plasma column that leads to a gas measured temperature equal to 3500 K, an excitation temperature of about 9500 K and an atomic oxygen density 2.09×1017± 0.2×10¹⁷ cm ⁻³ . This is in very good agreement with the TALIF measurement, which is equal to 2.0×10¹⁷ cm ⁻³ .     

Time-Resolved Optical Emission Spectroscopy Diagnosis of CO2 Laser-Produced SnO2 Plasma

The spectral emission and plasma parameters of SnO_2 plasmas have been investigated.A planar ceramic SnO_2 target was irradiated by a CO2 laser with a full width at half maximum of 80 ns.The temporal behavior of the specific emission lines from the SnO_2 plasma was characterized.The intensities of Sn I and Sn II lines first increased,and then decreased with the delay time.The results also showed a faster decay of Sn I atoms than that of Sn II ionic species.The temporal evolutions of the SnO_2 plasma parameters(electron temperature and density) were deduced.The measured temperature and density of SnO_2 plasma are 4.38 eV to0.5 eV and 11.38×10~(17) cm~(-3) to 1.1×10~(17) cm~(-3),for delay times between 0.1 μs and 2.2 μs.We also investigated the effect of the laser pulse energy on SnO_2 plasma.     

Estimation of plasma parameters in the process of micro-scale powder plastic and characteristics of its products

The temperature and density of plasma jets were estimated with a Boltzmann plot and Stark broadening of Ar I (696.54 nm) lines by optical emission spectroscopy (OES) in the process of plasma plastic, and the morphology and microstructure of tungsten (W) powders were investigated by scanning electron microscope (SEM) and x-ray Diffraction (XRD), respectively. The results show that the assumption of local thermodynamic equilibrium (LTE) was invalid at the end of the plasma jets, and earlier than this after the injection of tungsten powder. The temperature and electron density of the plasma jets were up to about T=6797 K with Q_c=50 slpm and n_e=1.05×10¹⁶ cm⁻³ with Q_s=115 slpm at Z=60 mm, respectively, and both dropped rapidly with the injected tungsten powders of 20 μm. After the plasma plastic process, the spherical tungsten powders were prepared and there were some satellite particles on the surface of the spherical products. The tungsten powders were both composed of a single equilibrium α-W phase with a body centered cubic (bbc) crystal structure before and after plasma treatment.     

Characterization of a microsecond pulsed non-equilibrium atmospheric pressure Ar plasma using laser scattering and optical emission spectroscopy

A non-equilibrium atmospheric pressure argon(Ar) plasma excited by microsecond pulse is studied experimentally by laser scattering and optical emission spectroscopy(OES), and theoretically by collisional-radiative(CR) model. More specifically, the electron temperature and electron density of plasma are obtained directly by the laser Thomson scattering, the gas temperature is measured by laser Raman scattering, the optical emissions of excited Ar states of plasma are measured by OES. The laser scattering results show that the electron temperature is about 1 eV which is similar to that excited by 60 Hz AC power, but the gas temperature is as low as 300 K compared to about 700 K excited by 60 Hz AC power. It is shown that the microsecond pulsed power supply, rather than nanosecond ones, is short enough to reduce the gas temperature of atmospheric pressure plasma to near room temperature. The electron temperature and electron density are also obtained by CR model based on OES, and find that the intensities of the optical emission intensity lines of 727.41, 811.73, 841.08, 842.83, 852.44 and 912.86 nm of Ar can be used to characterize the behavior of electron density and electron temperature, it is very useful to quickly estimate the activity of the atmospheric pressure Ar plasma in many applications.     

Spectral Characteristics of Laser-Induced Graphite Plasma in Ambient Air

An experimental setup of laser-induced graphite plasma was built and the spectral characteristics and properties of graphite plasma were studied. From the temporal behavior of graphite plasma, the duration of CN partials(B~2∑~+→X~2∑~+) emission was two times longer than that of atomic carbon, and all intensities reached the maximum during the early stage from0.2 μs to 0.8 μs. The electron temperature decreased from 11807 K to 8755 K, the vibration temperature decreased from 8973 K to 6472 K, and the rotational temperature decreased from7288 K to 4491 K with the delay time, respectively. The effect of the laser energy was also studied, and it was found that the thresholds and spectral characteristics of CN molecular and C atomic spectroscopy presented great differences. At lower laser energies, the electron excited temperature, the electron density, the vibrational temperature and rotational temperature of CN partials increased rapidly. At higher laser energies, the increasing of electron excited temperature and electron density slow down, and the vibrational temperature and rotational temperature even trend to saturation due to plasma shielding and dissociation of CN molecules. The relationship among the three kinds of temperatures was T_(elec)T_(vib)T_(rot) at the same time. The electron density of the graphite plasma was in the order of 10~(17)cm~(-3) and 10~(18)cm~(-3).     

Development of a helicon-wave excited plasma facility with high magnetic field for plasma-wall interactions studies

The high magnetic field helicon experiment system is a helicon wave plasma(HWP)source device in a high axial magnetic field(B_0)developed for plasma–wall interactions studies for fusion reactors.This HWP was realized at low pressure(5?×?10~(-3)?-?10 Pa)and a RF(radio frequency,13.56 MHz)power(maximum power of 2 k W)using an internal right helical antenna(5 cm in diameter by 18 cm long)with a maximum B_0of 6300 G.Ar HWP with electron density~10~(18)–10~(20)m~(-3)and electron temperature~4–7 e V was produced at high B_0 of 5100 G,with an RF power of 1500 W.Maximum Ar~+ion flux of 7.8?×?10~(23)m~(-2)s~(-1)with a bright blue core plasma was obtained at a high B_0 of 2700 G and an RF power of 1500 W without bias.Plasma energy and mass spectrometer studies indicate that Ar~+ion-beams of 40.1 eV are formed,which are supersonic(~3.1c_s).The effect of Ar HWP discharge cleaning on the wall conditioning are investigated by using the mass spectrometry.And the consequent plasma parameters will result in favorable wall conditioning with a removal rate of 1.1?×?10~(24)N_2/m~2 h.     

Spectral characteristic of laser-induced plasma in soil

The spectral characteristic of laser-induced plasma in soil was studied in this work, laser-induced breakdown spectroscopy was used to analyze the spectral characteristic of plasma under the condition of different time delays and irradiances. Moreover, the time evolution characteristics of plasma temperature and electron density were discussed. Within the time delay range of 0-5 μs,the spectral intensity of the characteristic lines of Si I: 288.158 nm, Ti I: 336.126 nm, Al I:394.400 nm and Fe I: 438.354 nm of the four main elements in two kinds of national standard soil decayed exponentially with time. The average lifetime of the spectral lines was nearly 1.56 μs. Under the condition of different time delays, the spectral intensity of Pb I: 405.78 nm in soil increased linearly with laser energy. However, the slope between the spectral intensity and laser energy decreased exponentially with the increase in time delay, from 4.91 to 0.99 during 0-5 μs. The plasma temperature was calculated by the Boltzmann plot method and the electron density was obtained by inversion of the full width at half maximum of the spectrum. The plasma temperature decreased from 8900 K to 7800 K and the electron density decreased from 1.5 × 10~(17) cm~(-3) to 7.8 × 10~(16) cm~(-3) in the range of 0-5 μs.     

High-energy-density electron beam generation in ultra intense laser-plasma interaction

By using a two-dimensional particle-in-cell simulation,we demonstrate a scheme for highenergy-density electron beam generation by irradiating an ultra intense laser pulse onto an aluminum(Al) target.With the laser having a peak intensity of 4?×?1023W cm~(-2),a high quality electron beam with a maximum density of 117 ncand a kinetic energy density up to8.79?×?1018J m~(-3) is generated.The temperature of the electron beam can be 416 Me V,and the beam divergence is only 7.25°.As the laser peak intensity increases(e.g.,1024 W cm~(-2)),both the beam energy density(3.56?×?1019J m~(-3)) and the temperature(545 Me V) are increased,and the beam collimation is well controlled.The maximum density of the electron beam can even reach 180 nc.Such beams should have potential applications in the areas of antiparticle generation,laboratory astrophysics,etc.     

Experimental investigation on the evolution of plasma properties in the discharge channel of a pulsed plasma thruster

Pulsed plasma thrusters(PPTs) are an attractive form of micro-thrusters due to advantages such as their compactness and lightweight design compared to other electric propulsion systems.Experimental investigations on their plasma properties are beneficial in clarifying the complex process of plasma evolution during the micro-second pulse discharge of a PPT. In this work, the multi-dimensional evolutions of the light intensity of the PPT plasma with wavelength, time, and position were identified. The plasma pressure was obtained using an iterative process with composition calculations. The results show that significant ion recombination occurred in the discharge channel since the line intensities of CII, CIII, CIV, and FII decreased and those of CI and FI increased as the plasma moved downstream. At the center of the discharge channel, the electron temperature and electron density were in the order of 10 000 K and 10~(17) cm~(-3),respectively. These had maximum values of 13 750 K and 2.3?×?10~(17) cm~(-3) and the maximum temperature occurred during the first half-cycle while the maximum number density was measured during the second half-cycle. The estimated plasma pressure was in the order of 10~5 Pa and exhibited a maximum value of 2.69?×?10~5 Pa.     

Plasma effects on the bacteria Escherichia coli via two evaluation methods

The degradation of?Escherichia coli?bacteria?by treatment with?cold,?weakly ionised, highly dissociated oxygen plasma,?with?an?electron temperature of 3 e V, a?plasma density of 8?×?10~(15)m~(-3) and a?neutral oxygen atom density of 3.5?×?1021m~(-3) was studied. To determine the ‘real' plasma effects,?two methods were used for evaluation and determination, as well as a comparison of the number of?bacteria that had?survived: the standard plate count technique(PCT) and?advanced fluorescence-activated cell sorting(FACS). Bacteria were deposited onto glass substrates and kept below 50 °C during the experiments with oxygen plasma. The results showed that the?bacteria had?fully degraded after about 2 min of plasma treatment, depending slightly on the amount of bacteria that had been?deposited on the substrates. The very?precise determination of the O flux on?the substrates and the two-method comparison allowed for the determination of the critical dose of oxygen atoms required for the destruction of a bacterial cell wall—about 6?×?10~(24)m~(-2)—as well as deactivation of the substrates—about 8?×?1025m~(-2).These results were taken in order to discuss other results obtained by comparable studies and scientific method?evaluations in the determination of plasma effects on bacteria.     

Experimental and simulation investigation of electrical and plasma parameters in a low pressure inductively coupled argon plasma

The electrical and plasma parameters of a low pressure inductively coupled argon plasma are investigated over a wide range of parameters(RF power, flow rate and pressure) by diverse characterizations. The external antenna voltage and current increase with the augment of RF power, whereas decline with the enhancement of gas pressure and flow rate conversely.Compared with gas flow rate and pressure, the power transfer efficiency is significantly improved by RF power, and achieved its maximum value of 0.85 after RF power injected excess125 W. Optical emission spectroscopy(OES) provides the local mean values of electron excited temperature and electron density in inductively coupled plasma(ICP) post regime, which vary in a range of 0.81 eV to 1.15 eV and 3.7×10~(16)m~(-3)to 8.7×10~(17)m~(-3)respectively. Numerical results of the average magnitudes of electron temperature and electron density in twodimensional distribution exhibit similar variation trend with the experimental results under different operating condition by using COMSOL Multiphysics. By comprehensively understanding the characteristics in a low pressure ICP, optimized operating conditions could be anticipated aiming at different academic and industrial applications.     

Oxide Coated Cathode Plasma Source of Linear Magnetized Plasma Device

Plasma source is the most important part of the laboratory plasma platform for fundamental plasma experimental research. Barium oxide coated cathode plasma source is well recognized as an effective technique due to its high electron emission current. An indirectly heated oxide coated cathode plasma source has been constructed on a linear magnetized plasma device. The electron emission current density can reach 2 A/cm 2 to 6 A/cm ² in pulsed mode within pulse length 5–20 ms. A 10 cm diameter, 2 m long plasma column with density 10 ¹⁸ m ⁻³ to 10 ¹⁹ m ³ and electron temperature T_e ≈ 3–7 eV is produced. The spatial uniformity of the emission ability is less than 4% and the discharge reproducibility is better than 97%. With a wide range of the plasma parameters, this kind of plasma source provides great flexibility for many basic plasma investigations. The detail of construction and initial characterization of oxide coated cathode are described in this paper.     

Spatial Evolution Study of EEDFs and Plasma Parameters in RF Stochastic Regime by Langmuir Probe

An RF compensated cylindrical Langmuir probe system has been developed and used to characterize an RF capacitive two temperature plasma discharge in a stochastic mode. The novelty of the work presented here is the use of the driven electrode （cathode） without ground shield. Measurements of the electron energy distribution function （EEDF） and plasma parameters were achieved under the following conditions： 50 W of RF power and 5× 10-2 mbar of argon pressure. The probe measurements are performed at 3 cm above the electrode and the probe was shifted radially （r direction） from the center （r = 0 cm） of the inter-electrodes region towards the chamber wall （R = 10.75 cm）. The results show that the EEDF is bi-Maxwellian and its shape remains the same through the scanned region. The farther the probe from the central region, the lower the EEDF maximum. The plasma density is observed to decrease according to a Gaussian profile along the radial direction and falls to 50% of its maximum when close to the cathode edge （r = 5.5 cm）. At the same time the effective electron temperature remains constant for r〈4 cm and increases for r≥4 cm. The high-temperature and low-temperature electrons＇ densities and temperatures are also discussed in the article.     

Experimental study of density pump-out on EAST

In the experimental advanced superconducting tokamak,density pump-out phenomena were observed by using a multi-channel polarimeter-interferometer system under different heating schemes of ion cyclotron resonant heating,electron cyclotron resonance heating,and neutral beam injection.The density pump-out was also induced with application of resonant magnetic perturbation,accompanied with a degradation of particle confinement.For the comparison analysis in all heating schemes,the typical plasma parameters are plasma current 400 k A,toroidal field 2 T,and line average density 2?×?10~(19)m~(-3).The experimental results show that the degree of pump-out is concerned with electron density and heating power.Low density deuterium low confinement(L-mode) plasmas(3.5?×?10~(19)m~(-3)) show strong pump-out effects.The density pump-out correlated with a significant drop of particle confinement.     

A comparison of emissive and cold floating probe techniques for electric potential measurements in rf inductive discharge

A cold floating probe method was compared with the emissive floating probe method in terms of a low-pressure radio-frequency inductive discharge. The dependences of difference between the plasma potential and the floating potential on the electron temperature 1–8 eV, plasma density 10⁹ –10¹² cm⁻³ and magnetic field 100–650 G were obtained. It was demonstrated that the difference between the potentials that obtained by these two methods can differ significantly from the expected value of 5.2 kT_e/e for argon.     

Diagnostics of Argon Inductively Coupled Plasma and Dielectric Barrier Discharge Plasma by Optical Emission Spectroscopy

1. IntroductionArgon plasma has been frequently used for mate-rial processing and film fabrication processes [1l [21 [31.The efficiency of these processes has very close rela-tion with plasma parameters [4][5], such as ion den-sity, electron temperature and ion energy dlstrlbu-tion. Lots of research has been done on the relation-ship between efficiency and availability of materialprocessing and plasma parameters [6][7].Both lCP dlscharge and DBD discharge are newtype plasma systems developed…     

Inactivation of Staphylococcus aureus by the synergistic action of charged and reactive plasma particles

In this paper, a low-pressure capacitively coupled plasma discharge sustained in an argonoxygen mixture was studied in order to evaluate its properties in terms of inactivation of Staphylococcus aureus. The plasma parameters as electron temperature and plasma density were measured by the Langmuir probe (N_e ≈ 10¹⁵ m⁻³, T_e ≈ 1.5 eV), while the neutral atom density was in the range of 10²¹ m⁻³. In the plasma phase, oxygen radicals were taken as reference of the reactive species with antimicrobial activity, and oxygen spectral lines, over a range of plasma process parameters, were investigated by the optical emission spectroscopy. Optimal plasma conditions were found, and a count reduction of 4 log in a few minutes of the bacterium proves the potentiality of an industrial grade plasma reactor as a sterilization agent.     

Numerical simulation of atmospheric pulse-modulated radio-frequency glow discharge ignition characteristics assisted by a pulsed discharge

A one-dimensional self-consistent fluid numerical model was developed to study the ignition characteristics of a pulse-modulated(PM) radio-frequency(RF) glow discharge in atmospheric helium assisted by a sub-microsecond voltage excited pulsed discharge. The temporal evolution of discharge current density and electron density during PM RF discharge burst was investigated to demonstrate the discharge ignition characteristics with or without the pulsed discharge. Under the assistance of pulsed discharge, the electron density in RF discharge burst reaches the magnitude of 1.87 × 10~(17) m~(-3) within 10 RF cycles, accompanied by the formation of sheath structure. It proposes that the pulsed discharge plays an important role in the ignition of PM RF discharge burst. Furthermore, the dynamics of PM RF glow discharge are demonstrated by the spatiotemporal evolution of the electron density with and without pulsed discharge. The spatial profiles of electron density, electron energy and electric field at specific time instants are given to explain the assistive role of the pulsed discharge on PM RF discharge ignition.     

Optical absorption of metallic Zn nanoparticles in Zn ion implanted sapphire

Zn⁺ ion implantation (48 keV) was performed at room temperature up to a fluence of 5 × 10¹⁷ cm⁻² in -Al₂O₃ single crystals. X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and optical absorption spectroscopy were utilized to characterize the optical properties, chemical charge states and the microstructure of embedded metallic Zn nanoparticles, respectively. XPS analysis indicated that implanted Zn ions are in the charge state of metallic Zn⁰. TEM analysis revealed the metallic Zn nanoparticles of 3–10 nm in the as-implanted sample at a fluence of 1 × 10¹⁷ cm⁻². A selected area electron diffraction (SAD) pattern indicates the random orientation of the Zn nanoparticles. A clear absorption peak appeared gradually in the optical absorption spectra of the as-implanted crystals, due to surface plasma resonance (SPR) of Zn nanoparticles. The wavelength of the absorption peak shifted from 260 nm to 285 nm with the increasing ion fluence, ascribed to the growth of Zn nanoparticles.     

Line identification of extreme ultraviolet(EUV) spectra from low-Z impurity ions in EAST tokamak plasmas

Extreme ultraviolet(EUV) spectra emitted from low-Z impurity ions in the wavelength range of10–500 ? were observed in Experimental Advanced Superconducting Tokamak(EAST)discharges. Several spectral lines from K-and L-shell partially ionized ions were successfully observed with sufficient spectral intensities and resolutions for helium, lithium, boron, carbon,oxygen, neon, silicon and argon using two fast-time-response EUV spectrometers of which the spectral intensities are absolutely calibrated based on the intensity comparison method between visible and EUV bremsstrahlung continua. The wavelength is carefully calibrated using wellknown spectra. The lithium, boron and silicon are individually introduced for the wall coating of the EAST vacuum vessel to suppress mainly the hydrogen and oxygen influxes from the vacuum wall, while the carbon and oxygen intrinsically exist in the plasma. The helium is frequently used as the working gas as well as the deuterium. The neon and argon are also often used for the radiation cooling of edge plasma to reduce the heat flux onto the divertor plate. The measured spectra were analyzed mainly based on the database of National Institute of Standards and Technology. As a result, spectral lines of He Ⅱ, Li Ⅱ–Ⅲ, B Ⅳ–Ⅴ, C Ⅲ–Ⅵ, O Ⅲ–Ⅷ, Ne Ⅱ–Ⅹ,Si Ⅴ–Ⅻ, and Ar Ⅹ–XVI are identified in EAST plasmas of which the central electron temperature and chord-averaged electron density range in T_(e0)=0.6–2.8 keV and n_e=(0.5–6.0)×10~(19) m~(-3), respectively. The wavelengths and transitions of EUV lines identified here are summarized and listed in a table for each impurity species as the database for EUV spectroscopy using fusion plasmas.