Characteristic tryptic peptides and gelling properties of porcine skin gelatin affected by thermal action

Thermal action in extraction process had effects on characteristic tryptic peptides identification and gelling properties of porcine gelatin. SDS-PAGE, HPLC-LTQ/Orbitrap high-resolution mass spectrometry, texture analyser and rheometer were used to evaluate collagen depolymerisation degree, characteristic tryptic peptides and gelling properties of gelatins prepared in various thermal actions. Results showed that with increasing temperature and time, depolymerisation degree enlarged, while gel strength, gelling and melting temperature decreased. Mass spectra showed that 47 and 49 common characteristic tryptic peptides were identified in gelatins extracted at 50 °C and 100 °C with various times, respectively. Moreover, 34 common characteristic tryptic peptides were identified in all gelatin samples. Further comparison between this work and our previous investigations yielded 20 common characteristic tryptic peptides, which stably exist in various thermal actions. These common characteristic tryptic peptides may be very helpful for the accurate authentication of porcine gelatin.     

A first-principles investigation on mechanical and metallic properties of titanium carbides under pressure

The titanium carbides are potential candidates to achieve both high hardness and refractory property. We carried out a structural search for titanium carbides at three pressures of 0 GPa, 30 GPa and 50 GPa. A phase diagram of the Ti-C system at 0 K was obtained by elucidating formation enthalpies as a function of compositions, and their mechanical and metallic properties of titanium carbides were investigated systematically. We also discussed the relation of titanium concentration to the both mechanical and metallic properties of titanium carbides. It has been found that the average valence electron density and tractility improved at higher concentrations of titanium, while the degree of covalent bonding directionality decreased. To this effect, the hardness of titanium carbide decreases as the content of titanium increases. Our results indicated that the titanium content significantly affected the metallic properties of the Ti-C system.     

Optimal Block Design for Asynchronous Wake-Up Schedules and Its Applications in Multihop Wireless Networks

In this paper, we consider the problem of designing optimal asynchronous wake-up schedules to facilitate distributed power management and neighbor discovery in multihop wireless networks. We first formulate it as a block design problem and derive the fundamental trade-offs between wake-up latency and the average duty cycle of a node. After the theoretical foundation is laid, we then devise a neighbor discovery and schedule bookkeeping protocol that can operate on the optimal wake-up schedule derived. To demonstrate the usefulness of asynchronous wake-up, we investigate the efficiency of neighbor discovery and the application of on-demand power management, which overlays a desirable communication schedule over the wake-up schedule mandated by the asynchronous wake-up mechanism. Simulation studies demonstrate that the proposed asynchronous wake-up protocol has short discovery time which scales with the density of the network; it can accommodate various traffic characteristics and loads to achieve an energy savings that can be as high as 70 percent, while the packet delivery ratio is comparable to that without power management.     

Fastmet工艺评述

介绍了Ｆａｓｔｍｅｔ工艺及发展状况，并对工艺特点和指标进行了分析。使用冷固结含碳球团和转底炉使该工艺可直接采用粉矿和提高生产效率，但因硫含量高、铁品位低而产品质量较差。不过投资和生产成本与传统工艺比较却占有较大优势。     

Further results on local stability of REM algorithm with time-varying delays

This letter presents some further results on the local stability in equilibrium for Internet congestion control algorithm proposed by Low et al., (IEEE/ACM Transactions on Networking, 1999). The propagation delay d(t) is assumed to be time-varying and have maximum and minimum delay bounds (i.e., d/sub m//spl les/d(t)/spl les/d/sub M/), which is more general than the assumption (0相似文献   

硫酸钙氨法制取硫酸钾新工艺的实验研究

利用K2 +2 ,Ca2 +/ /SO2 -4 ,Cl2 -2 ,NH3—H2 O混合体系相图作为工艺指导 ,进行硫酸钙制取硫酸钾工艺的相图研究和分析 ,确定实验优选因素及水平并进行正交实验 ,根据实验结果进行极差分析 ,得出新的结论。合适的工艺条件为 :氨浓度为 40 % ,配料比n( 2KCl) :n(CaSO4 ·2H2 O)为 1:1,反应温度为 5℃ ,反应时间为 1h。     

Crystal growth of selected II–VI semiconducting alloys by directional solidification: Part I Ground-based experiments

A series of Hg_0.84Zn_0.16 Te crystal ingots have been grown from pseudobinary melts by the Bridgmam–Stockbarger type directional solidification using a Marshall Space Flight Center/Space Science Laboratory heat-pipe furnace and the ground control experiment laboratory furnace of the crystal growth furnace which was flown on the first United States Microgravity Mission. A number of translation rates and a series of hot- and cold-zone temperatures were employed to assess the influence of growth parameters on the crystal properties for the purpose of optimizing the in-flight growth conditions. This revised version was published online in November 2006 with corrections to the Cover Date.     

Ion irradiation—induced structure damage to botanic samples using the ion transmission energy spectrum

1 INTRODUCTIONThe new aPplications of low energy heavy ion beam in irradi4ted botanical materialswere studied in recellt yeaxs. The beaminduced mutation effect on crop seeds has causedthe attention of physicist and biologists.[1l:] FOr examPle, 1ow energy ions can induceremarkable mutation to rice seeds.[3] There are many special phenomena when heavyions bombard botanic sW1e due to its special structure. Some studies showed that tllepenetration depths of some ions were far larger than t…     

Air bearing design, optimization, stability analysis andverification for sub-25 nm flying

Three sub-25 nm fly height sliders are presented for near contact recording. The designs are geared towards the goal of achieving 10 Gb/in ² areal density. The optimization procedure presented shows promise for facilitating achievement of this goal. The dynamic simulations show the stability of these designs when disturbed from their steady state conditions     

阴极爆炸发射电子电离气体原初过程的动力学模拟

基于阴极爆炸发射电子和电子对气体的碰撞电离模型 ,用胞中粒子 (PIC)模拟方法对单间隙冷阴极气体放电过程中阴极爆炸发射产生的电子和电子碰撞电离产生质子的动力学特性进行了研究。分别给出了在 1.33× 10 - 2 Pa氢气压和 10kV间隙电压下 ,气体放电过程中电子和质子的空间和相空间分布、速度统计分布以及轴线上电荷密度分布 ,分析了阴极爆炸发射电子电离过程。模拟结果表明 ,间隙中电子的最大速度达 5 .8× 10 7m/s ,而只有少数的气体电离产生的质子最大速度达到 1.3× 10 6 m/s。