Low shear rheological behaviour of two-phase mesophase pitch

The low shear rate rheology of two phase mesophase pitches derived from coal tar pitch has been investigated. Particulate quinoline insolubles (QI) stabilised the mesophase spheres against coalescence. Viscosity measurements over the range 10–10⁶ Pa s were made at appropriate temperature ranges. Increasing shear thinning behaviour was evident with increasing mesophase content. At low mesophase contents the dominant effect on the near Newtonian viscosity was temperature but at higher contents it was the shear rate; temperature dependence declined to near zero. The data indicated that agglomeration could be occurring at intermediate mesophase volume fractions, 0.2–0.3. The Krieger–Dougherty function and its emulsion analogue indicated that in this region the mesophase pitch emulsions actually behaved like ‘hard’ sphere systems and the effective volume fraction was estimated as a function of shear rate illustrating the change in extent of agglomeration. At the higher volume fractions approaching the maximum packing fraction, which could only be measured at higher temperatures, the shear thinning behaviour changed in character and it is considered that this is possibly due to shear induced deformation and breakup of dispersed drops in the shear field.     

High-temperature stability of Mg(Al,Cr)2O4 spinel co-existing with calcium aluminates in air

Cr₂O₃ is a well-known corrosion resistant oxide used in refractory applications. However, it can oxidize into toxic and water-soluble Cr(VI) compounds upon reaction with calcium aluminate cement phases in the presence of oxygen, which subsequently causes disposal problems after use. This study describes the extent to which chromium in the spinel Mg(Al,Cr)₂O₄ phase can be oxidized to Cr(VI) when it reacts with the calcium aluminate cement phases C₁₂A₇, CA, CA₂ and free CaO at 1300 °C in air, using XRD, XPS and leaching tests (TRGS 613 standard) as analytical tools. On reaction with CaO, the Mg(Al,Cr^III)₂O₄ spinel mainly transformed into hauyne (Ca₄Al₆Cr^VIO₁₆) and Ca₅Cr₃O₁₂ which contains both Cr(IV) and Cr(VI). The reaction of C₁₂A₇ and CA with the spinel phase also resulted in the formation of Ca₄Al₆CrO₁₆. Conversely, the reaction of Mg(Al,Cr^III)₂O₄ spinel with CA₂ resulted in the formation of only a trace amount of Cr(VI). Water-soluble Cr(VI) leached in large quantities (>100 mg/L) from samples where the Mg(Al,Cr^III)₂O₄ reacted with either C₁₂A₇ or CA. Almost no Cr(VI) leached from the sample when Mg(Al,Cr^III)₂O₄ reacted with CaO, using the standard TRGS 613 leach test, but a significant amount of Cr(VI) was released into solution when leached with a HCl solution for 12 h. Both Cr(IV) and Cr(VI) present in the Ca₅Cr₃O₁₂ dissolved into acidic solution. Only a small amount of Cr(VI) leached from the sample that resulted when spinel was reacted with CA₂, even after a prolonged HCl leach. Cr(III) in spinel Mg(Al,Cr)₂O₄ is very stable and does not leach in either distilled water or acidic solution.     

Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.     

Ce对440C不锈轴承钢夹杂物演变的影响

为探究稀土Ce对440C不锈轴承钢中夹杂物的改性作用,利用实验室MoSi₂电阻炉对440C不锈轴承钢进行稀土Ce处理,采用OM、SEM等系统分析了Ce的添加对440C不锈轴承钢脱氧及夹杂物演变的影响。结果表明,随着Ce加入量的增加,其收得率逐渐升高。Ce的加入使钢中TO质量分数由0.002 5%降低至0.001 2%。未加入Ce的钢中夹杂物主要为Al₂O₃、MnS以及镁铝尖晶石;加入质量分数为0.011 5%的Ce后,夹杂物被改性为以Ce-Al-O为主的夹杂物;当Ce的添加量达到0.036 4%时,夹杂物被完全改性为Ce-O-S夹杂物。适量的Ce可以降低夹杂物尺寸及面积比例,但过量加入会使夹杂物尺寸变大。在本试验条件下,当Ce质量分数为0.011 5%时,钢中夹杂物细小弥散效果最明显。以上结论可为Ce在高碳铬不锈轴承钢中的应用提供参考。     

Evolution of carbides and carbon content in matrix of an ultra-high carbon sintered steel during heat treatment process

DTA, thermal expansion, XRD, and SEM were used to evaluate the effect of quenching temperature on the mechanical properties and microstructure of a novel sintered steel Fe-6Co-1Ni-5Cr-5Mo-1C. Lattice parameters and the mass fraction of carbon dissolved in the matrix of the steel quenched were investigated. It is discovered that the hardness of the steel increases with quench-ing temperature in the range of 840-900℃ and remains constant in the range of 900 to 1100℃. It decreases rapidly when the tem-perature is higher than 1100℃. The mass fraction of carbon dissolved in the matrix of the steel quenched at 840℃ is 0.38, but when the quenching temperature is increased to 1150℃, it increases to 0.98. The carbides formed during sintering are still present at grain boundaries and in the matrix of the steel quenched at low quenching temperatures, such as 840℃. When the quenching temperature is increased to 1150℃, most of the carbides at grain boundaries are dissolved with just a small amount of spherical M23C6 existing in the matrix of the quenched steel.     

Growth characteristics and kinetics of niobium carbide coating obtained on AISI 52100 by thermal-reactive diffusion technique

Niobium carbide coating was produced by thermal-reactive diffusion technique on AISI 52100 steel in salt bath at 1 123 K, 1 173 K, and 1 223 K for 1, 2, 4, and 6 hours. The salt consisted of borax, sodium fl uoride, boron carbide, and niobium pentoxide. The presence of NbC phase on the steel surface was confi rmed by X-ray diffraction analysis. Microscopic observation showed that niobium carbide coating formed on the substrate was smooth and compact. There was a distinct and fl at interface between the coating and substrate. The micro-hardness of niobium carbide coating was 2892±145HV. The thickness of coating ranged from 1.6 μm to 14μm. The forming kinetics of niobium carbide coating was revealed. Moreover, a contour diagram derived from experimental data was graphed for correct selection of process parameters. Some mathematical equations were built for predicting the coating thickness with predetermined processing temperature and time. The results showed that these mathematical equations are very practical as well as the kinetics equation.     

1-D transient numerical model of a regenerator in a novel sub Kelvin Active Magnetic Regenerative Refrigerator

A sub Kelvin Active Magnetic Regenerative Refrigerator (AMRR) is being developed at the University of Wisconsin – Madison. This AMRR consists of two circulators, two regenerators, one superleak, one cold heat exchanger, and two warm heat exchangers. The circulators are novel non-moving part pumps that reciprocate a superfluid mixture of ⁴He–³He in the system. Heat from the mixture is removed within the two regenerators of this tandem system. An accurate model of the regenerators in this AMRR is necessary in order to predict the performance of these components, which in turn helps predicting the overall performance of the AMRR system. This work presents modeling methodology along with results from a 1-D transient numerical model of the regenerators of an AMRR capable of removing 2.5 mW at 850 mK at cyclic steady state.