Solution-Synthesized Multifunctional Janus Nanotree Microswimmer

Synthetic active matters are perfect model systems for non-equilibrium thermodynamics and of great potential for novel biomedical and environmental applications. However, most applications are limited by the complicated and low-yield preparation, while a scalable synthesis for highly functional microswimmers is highly desired. In this paper, an all-solution synthesis method is developed where the gold-loaded titania-silica nanotree can be produced as a multi-functional self-propulsion microswimmer. By applying light, heat, and electric field, the Janus nanotree demonstrated multi-mode self-propulsion, including photochemical self-electrophoresis by UV and visible light radiation, thermophoresis by near-infrared light radiation, and induced-charge electrophoresis under AC electric field. Due to the scalable synthesis, the Janus nanotree is further demonstrated as a high-efficiency, low-cost, active adsorbent for water decontamination, where the toxic mercury ions can be reclaimed with enhanced efficiency.     

乌兰矿采矿现状及技术应对方案

本文分析了乌兰矿投产前期采矿现状及存在的主要问题,针对该矿所处蒙古国经济落后、投资风险大的现实状况,为避免生产中断、规避投资风险,早日回收前期投资考虑,采取了双斜坡道开拓、全尾胶结充填、高端壁空场嗣后充填采矿、多中段组合式连续开采等系列技术应对方案。大大降低了一次性投资规模及投资风险,前期投资得以快速回笼的同时,矿山产能也充分释放,确保了矿山的持续稳定,取得了较好的经济和社会效益。为海外地下近地表矿体开采矿山规避投资风险提供了很好的技术方案借鉴。     

Deep reinforcement learning-based cooperative interactions among heterogeneous vehicular networks

Most real-world vehicle nodes can be structured into an interconnected network of vehicles. Through structuring these services and vehicle device interactions into multiple types, such internet of vehicles becomes multidimensional heterogeneous overlay networks. The heterogeneousness of the overlays makes it difficult for the overlay networks to coordinate with each other to improve their performance. Therefore, it poses an interesting but critical challenge to the effective analysis of heterogeneous virtual vehicular networks. A variety of virtual vehicular networks can be easily deployed onto the native network by applying the concept of SDN (Software Defined Networking). These virtual networks reflect their heterogeneousness due to their different performance goals, and they compete for the same physical resources of the underlying network, so that a sub-optimal performance of the virtual networks may be achieved. Therefore, we propose a Deep Reinforcement Learning (DRL) approach to make the virtual networks cooperate with each other through the SDN controller. A cooperative solution based on the asymmetric Nash bargaining is proposed for co-existing virtual networks to improve their performance. Moreover, the Markov Chain model and DRL resolution are introduced to leverage the heterogeneous performance goals of virtual networks. The implementation of the approach is introduced, and simulation results confirm the performance improvement of the latency sensitive, loss-rate sensitive and throughput sensitive heterogeneous vehicular networks using our cooperative solution.     

基于滑模的运载器主动段俯仰通道姿控系统设计

与传统比例-积分-微分（PID）控制方法相比，滑模控制（SMC）方法可以比较容易地将不确定性纳入控制器设计中，从而增强系统的鲁棒性。探索了SMC技术在运载器主动段姿态控制中的工程应用，首先通过分析基于趋近律的SMC系统，提出了降低不连续切换项系数的需求，然后研究了基于干扰上界的SMC方法。三通道小偏差仿真结果验证了两种方法的控制效果，表明第2种控制器的鲁棒性更好，稳态误差小，同时发动机喷管摆角需求较小。     

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.     

Epos – an instrument for the assessment of the ethical position in software development

Digital technology becomes more powerful, intelligent, pervasive and ubiquitous. Ethical aspects of this development have not yet drawn the appropriate attention of researchers and engineers. This paper presents an instrument that aims at measuring the individual ethical position with regard to the design and development of computer software. The development of the Epos tool was based on two data collections. The data of the first survey (n₁ = 147 participants) were used to select items and to determine the factorial structure of the questionnaire. Results show that the Epos instrument reliably assesses peoples’ ethical opinion with respect to five central components: (1) regulation, (2) data privacy, (3) domain specific knowledge, (4) societal responsibility and (5) company responsibility. In the second survey, we determined the stability of the instruments factor structure by assessing a sample of n₂?=?196 participants. A confirmatory factor analysis (CFA) supported the initial factor structure. Next steps and further implications are discussed regarding the final version of the questionnaire.     

Hydrogenation process in multiphase alloys of Ti-Zr-Mn-V system on the example of Ti42.75Zr27Mn20.25V10 alloy

The influence of phase composition and microstructure of Ti_42.75Zr₂₇Mn_20.25V₁₀ alloy on its hydrogenation kinetic and phase composition of hydrogenated product was studied. It is established that the process of dissociation of hydrogen molecules begins on the surface of Laves phase crystallites. The dissolution of atomic hydrogen in the material volume leads to the formation of cracks in the intermetallic crystallites, which further appear as additional centers of dissociation of hydrogen molecules and noticeably accelerate the diffusion of hydrogen into the bulk material. It was shown that the Laves phase acts as a donor of atomic hydrogen for the BCC solid solution during hydrogenation of two-phase structure, initiating intensive hydrogenation of the BCC phase at room temperature.     

高强WSTi544221合金组织与性能研究

研究了轧制变形量对WSTi544221合金棒材显微组织和力学性能的影响,并对Φ10 mm规格的棒材进行不同制度的固溶+时效处理,对比了不同热处理状态下棒材的组织和力学性能。结果表明,随着轧制变形量的增大,WSTi544221合金棒材的晶粒细化程度增大,强度逐渐提高,但塑性变化不大。经870℃×1 h/WC+520℃×6 h/AC固溶+时效处理后,强度与塑性可以获得良好匹配,当抗拉强度达到1 610 MPa、屈服强度达到1 531 MPa时,延伸率和断面收缩率可分别保持在12%和43%。